mx53evk i.MX53
mx53loco i.MX53
mx6qarm2 i.MX6Q
+ mx6qsabrelite i.MX6Q
Enric Balletbo i Serra <eballetbo@iseebcn.com>
--- /dev/null
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := mx6qsabrelite.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+# Copyright (C) 2011 Freescale Semiconductor, Inc.
+# Jason Liu <r64343@freescale.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not write to the Free Software
+# Foundation Inc. 51 Franklin Street Fifth Floor Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.imxmage for more details about how-to configure
+# and create imximage boot image
+#
+# The syntax is taken as close as possible with the kwbimage
+
+# image version
+
+IMAGE_VERSION 2
+
+# Boot Device : one of
+# spi, sd (the board has no nand neither onenand)
+
+BOOT_FROM sd
+
+# Device Configuration Data (DCD)
+#
+# Each entry must have the format:
+# Addr-type Address Value
+#
+# where:
+# Addr-type register length (1,2 or 4 bytes)
+# Address absolute address of the register
+# value value to be stored in the register
+DATA 4 0x020e05a8 0x00000030
+DATA 4 0x020e05b0 0x00000030
+DATA 4 0x020e0524 0x00000030
+DATA 4 0x020e051c 0x00000030
+
+DATA 4 0x020e0518 0x00000030
+DATA 4 0x020e050c 0x00000030
+DATA 4 0x020e05b8 0x00000030
+DATA 4 0x020e05c0 0x00000030
+
+DATA 4 0x020e05ac 0x00020030
+DATA 4 0x020e05b4 0x00020030
+DATA 4 0x020e0528 0x00020030
+DATA 4 0x020e0520 0x00020030
+
+DATA 4 0x020e0514 0x00020030
+DATA 4 0x020e0510 0x00020030
+DATA 4 0x020e05bc 0x00020030
+DATA 4 0x020e05c4 0x00020030
+
+DATA 4 0x020e056c 0x00020030
+DATA 4 0x020e0578 0x00020030
+DATA 4 0x020e0588 0x00020030
+DATA 4 0x020e0594 0x00020030
+
+DATA 4 0x020e057c 0x00020030
+DATA 4 0x020e0590 0x00003000
+DATA 4 0x020e0598 0x00003000
+DATA 4 0x020e058c 0x00000000
+
+DATA 4 0x020e059c 0x00003030
+DATA 4 0x020e05a0 0x00003030
+DATA 4 0x020e0784 0x00000030
+DATA 4 0x020e0788 0x00000030
+
+DATA 4 0x020e0794 0x00000030
+DATA 4 0x020e079c 0x00000030
+DATA 4 0x020e07a0 0x00000030
+DATA 4 0x020e07a4 0x00000030
+
+DATA 4 0x020e07a8 0x00000030
+DATA 4 0x020e0748 0x00000030
+DATA 4 0x020e074c 0x00000030
+DATA 4 0x020e0750 0x00020000
+
+DATA 4 0x020e0758 0x00000000
+DATA 4 0x020e0774 0x00020000
+DATA 4 0x020e078c 0x00000030
+DATA 4 0x020e0798 0x000C0000
+
+DATA 4 0x021b081c 0x33333333
+DATA 4 0x021b0820 0x33333333
+DATA 4 0x021b0824 0x33333333
+DATA 4 0x021b0828 0x33333333
+
+DATA 4 0x021b481c 0x33333333
+DATA 4 0x021b4820 0x33333333
+DATA 4 0x021b4824 0x33333333
+DATA 4 0x021b4828 0x33333333
+
+DATA 4 0x021b0018 0x00081740
+
+DATA 4 0x021b001c 0x00008000
+DATA 4 0x021b000c 0x555A7975
+DATA 4 0x021b0010 0xFF538E64
+DATA 4 0x021b0014 0x01FF00DB
+DATA 4 0x021b002c 0x000026D2
+
+DATA 4 0x021b0030 0x005B0E21
+DATA 4 0x021b0008 0x09444040
+DATA 4 0x021b0004 0x00025576
+DATA 4 0x021b0040 0x00000027
+DATA 4 0x021b0000 0x831A0000
+
+DATA 4 0x021b001c 0x04088032
+DATA 4 0x021b001c 0x0408803A
+DATA 4 0x021b001c 0x00008033
+DATA 4 0x021b001c 0x0000803B
+DATA 4 0x021b001c 0x00428031
+DATA 4 0x021b001c 0x00428039
+DATA 4 0x021b001c 0x09408030
+DATA 4 0x021b001c 0x09408038
+
+DATA 4 0x021b001c 0x04008040
+DATA 4 0x021b001c 0x04008048
+DATA 4 0x021b0800 0xA1380003
+DATA 4 0x021b4800 0xA1380003
+DATA 4 0x021b0020 0x00005800
+DATA 4 0x021b0818 0x00022227
+DATA 4 0x021b4818 0x00022227
+
+DATA 4 0x021b083c 0x434B0350
+DATA 4 0x021b0840 0x034C0359
+DATA 4 0x021b483c 0x434B0350
+DATA 4 0x021b4840 0x03650348
+DATA 4 0x021b0848 0x4436383B
+DATA 4 0x021b4848 0x39393341
+DATA 4 0x021b0850 0x35373933
+DATA 4 0x021b4850 0x48254A36
+
+DATA 4 0x021b080c 0x001F001F
+DATA 4 0x021b0810 0x001F001F
+
+DATA 4 0x021b480c 0x00440044
+DATA 4 0x021b4810 0x00440044
+
+DATA 4 0x021b08b8 0x00000800
+DATA 4 0x021b48b8 0x00000800
+
+DATA 4 0x021b001c 0x00000000
+DATA 4 0x021b0404 0x00011006
+
+# set the default clock gate to save power
+DATA 4 0x020c4068 0x00C03F3F
+DATA 4 0x020c406c 0x0030FC00
+DATA 4 0x020c4070 0x0FFFC000
+DATA 4 0x020c4074 0x3FF00000
+DATA 4 0x020c4078 0x00FFF300
+DATA 4 0x020c407c 0x0F0000C3
+DATA 4 0x020c4080 0x000003FF
+
+# enable AXI cache for VDOA/VPU/IPU
+DATA 4 0x020e0010 0xF00000FF
+# set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7
+DATA 4 0x020e0018 0x007F007F
+DATA 4 0x020e001c 0x007F007F
--- /dev/null
+/*
+ * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx6x_pins.h>
+#include <asm/arch/iomux-v3.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+ return 0;
+}
+
+iomux_v3_cfg_t uart2_pads[] = {
+ MX6Q_PAD_EIM_D26__UART2_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6Q_PAD_EIM_D27__UART2_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t usdhc3_pads[] = {
+ MX6Q_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD3_DAT5__GPIO_7_0 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+iomux_v3_cfg_t usdhc4_pads[] = {
+ MX6Q_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6Q_PAD_NANDF_D6__GPIO_2_6 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg usdhc_cfg[2] = {
+ {USDHC3_BASE_ADDR, 1},
+ {USDHC4_BASE_ADDR, 1},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret;
+
+ if (cfg->esdhc_base == USDHC3_BASE_ADDR) {
+ gpio_direction_input(192); /*GPIO7_0*/
+ ret = !gpio_get_value(192);
+ } else {
+ gpio_direction_input(38); /*GPIO2_6*/
+ ret = !gpio_get_value(38);
+ }
+
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ s32 status = 0;
+ u32 index = 0;
+
+ for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
+ switch (index) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers"
+ "(%d) then supported by the board (%d)\n",
+ index + 1, CONFIG_SYS_FSL_USDHC_NUM);
+ return status;
+ }
+
+ status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
+ }
+
+ return status;
+}
+#endif
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: MX6Q-Sabre Lite\n");
+
+ return 0;
+}
mx53smd arm armv7 mx53smd freescale mx5 mx53smd:IMX_CONFIG=board/freescale/mx53smd/imximage.cfg
vision2 arm armv7 vision2 ttcontrol mx5 vision2:IMX_CONFIG=board/ttcontrol/vision2/imximage_hynix.cfg
mx6qarm2 arm armv7 mx6qarm2 freescale mx6 mx6qarm2:IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg
+mx6qsabrelite arm armv7 mx6qsabrelite freescale mx6 mx6qsabrelite:IMX_CONFIG=board/freescale/mx6qsabrelite/imximage.cfg
cm_t35 arm armv7 cm_t35 - omap3
omap3_overo arm armv7 overo - omap3
omap3_pandora arm armv7 pandora - omap3
--- /dev/null
+U-Boot for the Freescale i.MX6q SabreLite board
+
+This file contains information for the port of U-Boot to the Freescale
+i.MX6q SabreLite board.
+
+1. Boot source, boot from SD card
+---------------------------------
+
+The recent mainline U-Boot for the Freescale i.MX6q SabreLite board supports
+boot from SD card only. However, by default, the early version of SabreLite
+boards boot from the SPI NOR flash. These boards need to be reflashed with
+a small SD card loader to support boot from SD card. This small SD card loader
+will be flashed into the SPI NOR. The board will still boot from SPI NOR, but
+the loader will in turn request the BootROM to load the U-Boot from SD card.
+At the moment of writing, please check with Freescale on the availablity of
+this small SD loader binary.
+
+To update the SPI-NOR on the SabreLite board without the Freescale
+manufacturing tool use the following procedure:
+
+1. Write this SD card loader onto a large SD card using:
+
+ sudo dd if=MX6_SPI_to_SD_loader.bin of=/dev/sXx
+
+Note: Replace sXx with the device representing the SD card in your system.
+
+Note: This writes SD card loader at address 0
+
+2. Put this SD card into the slot for the large SD card (SD3 on the bottom of
+the board)
+
+3. Power-up the SabreLite, press 'space' to enter command mode in the U-Boot
+(the default one the board is shipped with, starting from the SPI NOR) and
+enter the following commands:
+
+ MX6Q SABRELITE U-Boot > mmc dev 0
+ MX6Q SABRELITE U-Boot > mmc read 0x10800000 0 200
+ MX6Q SABRELITE U-Boot > sf probe 1
+ MX6Q SABRELITE U-Boot > sf erase 0 0x40000
+ MX6Q SABRELITE U-Boot > sf write 0x10800000 0 0x40000
+
+4. done.
+
+In case you somehow do not succeed with this procedure you will have to use
+the Freescale manufacturing tool in order to reflash the SPI-NOR.
+
+Note: The board now boots from full size SD3 on the bottom of the board. NOT
+ the micro SD4/BOOT slot on the top of the board. I.e. you have to use
+ full size SD cards.
+
+This information is taken from
+
+https://wiki.linaro.org/Boards/MX6QSabreLite
+
+2. Build
+--------
+
+To build U-Boot for the SabreLite board:
+
+ make mx6qsabrelite_config
+ make u-boot.imx
+
+To copy the resulting u-boot.imx to the SD card:
+
+ sudo dd if=u-boot.imx of=/dev/sXx bs=512 seek=2&&sudo sync
+
+Note: Replace sXx with the device representing the SD card in your system.
--- /dev/null
+/*
+ * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX6Q Sabre Lite board.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MX6Q
+#define CONFIG_SYS_MX6_HCLK 24000000
+#define CONFIG_SYS_MX6_CLK32 32768
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#include <asm/arch/imx-regs.h>
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
+
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART2_BASE
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+
+#define CONFIG_BOOTDELAY 3
+
+#define CONFIG_LOADADDR 0x10800000
+#define CONFIG_SYS_TEXT_BASE 0x17800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "uimage=uImage\0" \
+ "console=ttymxc3\0" \
+ "mmcdev=0\0" \
+ "mmcpart=2\0" \
+ "mmcroot=/dev/mmcblk0p3 rootwait rw\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootm\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "dhcp ${uimage}; bootm\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev};" \
+ "if mmc rescan ${mmcdev}; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+
+#define CONFIG_ARP_TIMEOUT 200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT "MX6QSABRELITE U-Boot > "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 256
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START 0x10000000
+#define CONFIG_SYS_MEMTEST_END 0x10010000
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE (128 * 1024)
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
+#define CONFIG_ENV_SIZE (8 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_OF_LIBFDT
+
+#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff