Blackfin: serial: clean up muxing a bit

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

diff --git a/arch/blackfin/cpu/serial.h b/arch/blackfin/cpu/serial.h
index f9e311f3eee819620f186274011a242c2f5b39b8..b0cf09a2f586e1ae7579e11aca1cc70f67f8fa5d 100644 (file)
--- a/arch/blackfin/cpu/serial.h
+++ b/arch/blackfin/cpu/serial.h
@@ -74,23 +74,19 @@ struct bfin_mmr_serial {
 };
 #undef __BFP
 
-#ifndef UART_LSR
-# if (CONFIG_UART_CONSOLE == 3)
-#  define UART_BASE UART3_DLL
-# elif (CONFIG_UART_CONSOLE == 2)
-#  define UART_BASE UART2_DLL
-# elif (CONFIG_UART_CONSOLE == 1)
-#  define UART_BASE UART1_DLL
-# elif (CONFIG_UART_CONSOLE == 0)
-#  define UART_BASE UART0_DLL
-# endif
+#define __PASTE_UART(num, pfx, sfx) pfx##num##_##sfx
+#define _PASTE_UART(num, pfx, sfx) __PASTE_UART(num, pfx, sfx)
+#define MMR_UART(mmr) _PASTE_UART(CONFIG_UART_CONSOLE, UART, DLL)
+#define P_UART(pin) _PASTE_UART(CONFIG_UART_CONSOLE, P_UART, pin)
+
+#ifndef UART_DLL
+# define UART_DLL MMR_UART(DLL)
 #else
 # if CONFIG_UART_CONSOLE != 0
 #  error CONFIG_UART_CONSOLE must be 0 on parts with only one UART
 # endif
-# define UART_BASE UART_DLL
 #endif
-#define pUART ((volatile struct bfin_mmr_serial *)UART_BASE)
+#define pUART ((volatile struct bfin_mmr_serial *)UART_DLL)
 
 #ifdef __ADSPBF54x__
 # define ACCESS_LATCH()
@@ -106,18 +102,7 @@ __attribute__((always_inline))
 static inline void serial_do_portmux(void)
 {
        if (!BFIN_DEBUG_EARLY_SERIAL) {
-               const unsigned short pins[] = {
-#if CONFIG_UART_CONSOLE == 0
-                       P_UART0_TX, P_UART0_RX,
-#elif CONFIG_UART_CONSOLE == 1
-                       P_UART1_TX, P_UART1_RX,
-#elif CONFIG_UART_CONSOLE == 2
-                       P_UART2_TX, P_UART2_RX,
-#elif CONFIG_UART_CONSOLE == 3
-                       P_UART3_TX, P_UART3_RX,
-#endif
-                       0,
-               };
+               const unsigned short pins[] = { P_UART(RX), P_UART(TX), 0, };
                peripheral_request_list(pins, "bfin-uart");
                return;
        }
@@ -141,13 +126,11 @@ static inline void serial_do_portmux(void)
        }
        SSYNC();
 #elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__)
-# define DO_MUX(func, tx, rx) \
-       bfin_write_PORT_MUX(bfin_read_PORT_MUX() & ~(func)); \
-       bfin_write_PORTF_FER(bfin_read_PORTF_FER() | PF##tx | PF##rx);
-       switch (CONFIG_UART_CONSOLE) {
-       case 0: DO_MUX(PFDE, 0, 1); break;
-       case 1: DO_MUX(PFTE, 2, 3); break;
-       }
+       const uint16_t func[] = { PFDE, PFTE, };
+       bfin_write_PORT_MUX(bfin_read_PORT_MUX() & ~func[CONFIG_UART_CONSOLE]);
+       bfin_write_PORTF_FER(bfin_read_PORTF_FER() |
+                            (1 << P_IDENT(P_UART(RX))) |
+                            (1 << P_IDENT(P_UART(TX))));
        SSYNC();
 #elif defined(__ADSPBF54x__)
 # define DO_MUX(port, tx, rx) \
@@ -160,6 +143,12 @@ static inline void serial_do_portmux(void)
        case 3: DO_MUX(B, 6, 7); break; /* Port B; PB6 and PB7 */
        }
        SSYNC();
+#elif defined(__ADSPBF561__)
+       /* UART pins could be GPIO, but they aren't pin muxed.  */
+#else
+# if (P_UART(RX) & P_DEFINED) || (P_UART(TX) & P_DEFINED)
+#  error "missing portmux logic for UART"
+# endif
 #endif
 }