ARM1176: Coexist with other ARM1176 platforms

The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture.  The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.

Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.

1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.

2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM.  Added support for this capability in ARM1176 architecture.

3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.

4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include.  The presence
of this include prevents builds on other ARM1176 archs.

5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

diff --git a/arch/arm/cpu/arm1176/cpu.c b/arch/arm/cpu/arm1176/cpu.c
index befa0cdcc436eec15c4d654e2a1b8ba3d8e5f601..c0fd114e16305fab9f5f5f9aa688b5396ad9efd4 100644 (file)
--- a/arch/arm/cpu/arm1176/cpu.c
+++ b/arch/arm/cpu/arm1176/cpu.c
@@ -33,9 +33,6 @@
 
 #include <common.h>
 #include <command.h>
-#ifdef CONFIG_S3C64XX
-#include <asm/arch/s3c6400.h>
-#endif
 #include <asm/system.h>
 
 static void cache_flush (void);

diff --git a/arch/arm/cpu/arm1176/start.S b/arch/arm/cpu/arm1176/start.S
index e2b6c9b08d916d1c8caff4a17fed5609d0e35b06..a540edbfbf807bc008b4bd8b576510692b524d98 100644 (file)
--- a/arch/arm/cpu/arm1176/start.S
+++ b/arch/arm/cpu/arm1176/start.S
@@ -1,5 +1,5 @@
 /*
- *  armboot - Startup Code for S3C6400/ARM1176 CPU-core
+ *  armboot - Startup Code for ARM1176 CPU-core
  *
  * Copyright (c) 2007  Samsung Electronics
  *
@@ -35,9 +35,6 @@
 #ifdef CONFIG_ENABLE_MMU
 #include <asm/proc/domain.h>
 #endif
-#ifdef CONFIG_S3C64XX
-#include <asm/arch/s3c6400.h>
-#endif
 
 #if !defined(CONFIG_ENABLE_MMU) && !defined(CONFIG_SYS_PHY_UBOOT_BASE)
 #define CONFIG_SYS_PHY_UBOOT_BASE      CONFIG_SYS_UBOOT_BASE
@@ -172,14 +169,10 @@ cpu_init_crit:
        bic     r0, r0, #0x00000087     @ clear bits 7, 2:0 (B--- -CAM)
        orr     r0, r0, #0x00000002     @ set bit 2 (A) Align
        orr     r0, r0, #0x00001000     @ set bit 12 (I) I-Cache
+
        /* Prepare to disable the MMU */
-       adr     r1, mmu_disable_phys
-       /* We presume we're within the first 1024 bytes */
-       and     r1, r1, #0x3fc
-       ldr     r2, _TEXT_PHY_BASE
-       ldr     r3, =0xfff00000
-       and     r2, r2, r3
-       orr     r2, r2, r1
+       adr     r2, mmu_disable_phys
+       sub     r2, r2, #(CONFIG_SYS_PHY_UBOOT_BASE - TEXT_BASE)
        b       mmu_disable
 
        .align 5
@@ -189,14 +182,30 @@ mmu_disable:
        nop
        nop
        mov     pc, r2
+mmu_disable_phys:
+
+#ifdef CONFIG_DISABLE_TCM
+       /*
+        * Disable the TCMs
+        */
+       mrc     p15, 0, r0, c0, c0, 2   /* Return TCM details */
+       cmp     r0, #0
+       beq     skip_tcmdisable
+       mov     r1, #0
+       mov     r2, #1
+       tst     r0, r2
+       mcrne   p15, 0, r1, c9, c1, 1   /* Disable Instruction TCM if present*/
+       tst     r0, r2, LSL #16
+       mcrne   p15, 0, r1, c9, c1, 0   /* Disable Data TCM if present*/
+skip_tcmdisable:
+#endif
 #endif
 
-mmu_disable_phys:
-#ifdef CONFIG_S3C64XX
+#ifdef CONFIG_PERIPORT_REMAP
        /* Peri port setup */
-       ldr     r0, =0x70000000
-       orr     r0, r0, #0x13
-       mcr     p15,0,r0,c15,c2,4       @ 256M (0x70000000 - 0x7fffffff)
+       ldr     r0, =CONFIG_PERIPORT_BASE
+       orr     r0, r0, #CONFIG_PERIPORT_SIZE
+       mcr     p15,0,r0,c15,c2,4
 #endif
 
        /*
@@ -204,7 +213,25 @@ mmu_disable_phys:
         */
        bl      lowlevel_init           /* go setup pll,mux,memory */
 
-after_copy:
+#ifndef CONFIG_SKIP_RELOCATE_UBOOT
+relocate:                              /* relocate U-Boot to RAM           */
+       adr     r0, _start              /* r0 <- current position of code   */
+       ldr     r1, _TEXT_BASE          /* test if we run from flash or RAM */
+       cmp     r0, r1                  /* don't reloc during debug         */
+       beq     stack_setup
+
+       ldr     r2, _armboot_start
+       ldr     r3, _bss_start
+       sub     r2, r3, r2              /* r2 <- size of armboot            */
+       add     r2, r0, r2              /* r2 <- source end address         */
+
+copy_loop:
+       ldmia   r0!, {r3-r10}           /* copy from source address [r0]    */
+       stmia   r1!, {r3-r10}           /* copy to   target address [r1]    */
+       cmp     r0, r2                  /* until source end addreee [r2]    */
+       ble     copy_loop
+#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
+
 #ifdef CONFIG_ENABLE_MMU
 enable_mmu:
        /* enable domain access */
@@ -240,9 +267,9 @@ mmu_enable:
        nop
        nop
        mov     pc, r2
+skip_hw_init:
 #endif
 
-skip_hw_init:
        /* Set up the stack                                                 */
 stack_setup:
        ldr     r0, =CONFIG_SYS_UBOOT_BASE      /* base of copy in DRAM     */
@@ -310,6 +337,8 @@ phy_last_jump:
        mov     r0, #0
        mov     pc, r9
 #endif
+
+
 /*
  *************************************************************************
  *

diff --git a/include/configs/smdk6400.h b/include/configs/smdk6400.h
index f04feae21958f25530cd23ca0a35b57b317e83d7..624fe04b059203a96e457e71763b1e8efb103d96 100644 (file)
--- a/include/configs/smdk6400.h
+++ b/include/configs/smdk6400.h
@@ -40,6 +40,12 @@
 #define CONFIG_S3C64XX         1       /* in a SAMSUNG S3C64XX Family  */
 #define CONFIG_SMDK6400                1       /* on a SAMSUNG SMDK6400 Board  */
 
+#define CONFIG_SKIP_RELOCATE_UBOOT
+
+#define CONFIG_PERIPORT_REMAP
+#define CONFIG_PERIPORT_BASE   0x70000000
+#define CONFIG_PERIPORT_SIZE   0x13
+
 #define CONFIG_SYS_SDRAM_BASE  0x50000000
 
 /* input clock of PLL: SMDK6400 has 12MHz input clock */
@@ -61,8 +67,6 @@
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
 
-#undef CONFIG_SKIP_RELOCATE_UBOOT
-
 /*
  * Size of malloc() pool
  */