The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
Wolfgang Denk <wd@denx.de>
incaip MIPS32 4Kc
- purple MIPS64 5Kc
Thomas Lange <thomas@corelatus.se>
dbau1x00 MIPS32 Au1000
vct_premium_onenand_small \
"
-LIST_mips5kc=" \
- purple \
-"
+LIST_mips5kc=""
LIST_au1xx0=" \
dbau1000 \
SOBJS-$(CONFIG_INCA_IP) += incaip_wdt.o
COBJS-$(CONFIG_INCA_IP) += asc_serial.o incaip_clock.o
-COBJS-$(CONFIG_PURPLE) += asc_serial.o
COBJS-$(CONFIG_SOC_AU1X00) += au1x00_eth.o au1x00_serial.o au1x00_usb_ohci.o
SRCS := $(START:.o=.S) $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
*/
#include <config.h>
-
-#ifdef CONFIG_PURPLE
-#define serial_init asc_serial_init
-#define serial_putc asc_serial_putc
-#define serial_puts asc_serial_puts
-#define serial_getc asc_serial_getc
-#define serial_tstc asc_serial_tstc
-#define serial_setbrg asc_serial_setbrg
-#endif
-
#include <common.h>
#include <asm/inca-ip.h>
#include "asc_serial.h"
-#ifdef CONFIG_PURPLE
-
-#undef ASC_FIFO_PRESENT
-#define TOUT_LOOP 100000
-
-/* Set base address for second FPI interrupt control register bank */
-#define SFPI_INTCON_BASEADDR 0xBF0F0000
-
-/* Register offset from base address */
-#define FBS_ISR 0x00000000 /* Interrupt status register */
-#define FBS_IMR 0x00000008 /* Interrupt mask register */
-#define FBS_IDIS 0x00000010 /* Interrupt disable register */
-
-/* Interrupt status register bits */
-#define FBS_ISR_AT 0x00000040 /* ASC transmit interrupt */
-#define FBS_ISR_AR 0x00000020 /* ASC receive interrupt */
-#define FBS_ISR_AE 0x00000010 /* ASC error interrupt */
-#define FBS_ISR_AB 0x00000008 /* ASC transmit buffer interrupt */
-#define FBS_ISR_AS 0x00000004 /* ASC start of autobaud detection interrupt */
-#define FBS_ISR_AF 0x00000002 /* ASC end of autobaud detection interrupt */
-
-#else
-
-#define ASC_FIFO_PRESENT
-
-#endif
-
#define SET_BIT(reg, mask) reg |= (mask)
#define CLEAR_BIT(reg, mask) reg &= (~mask)
int serial_init (void)
{
-#ifdef CONFIG_INCA_IP
/* we have to set PMU.EN13 bit to enable an ASC device*/
INCAASC_PMU_ENABLE(13);
-#endif
/* and we have to set CLC register*/
CLEAR_BIT(pAsc->asc_clc, ASCCLC_DISS);
/* select input port */
pAsc->asc_pisel = (CONSOLE_TTY & 0x1);
-#ifdef ASC_FIFO_PRESENT
/* TXFIFO's filling level */
SET_BITFIELD(pAsc->asc_txfcon, ASCTXFCON_TXFITLMASK,
ASCTXFCON_TXFITLOFF, INCAASC_TXFIFO_FL);
ASCRXFCON_RXFITLOFF, INCAASC_RXFIFO_FL);
/* enable RXFIFO */
SET_BIT(pAsc->asc_rxfcon, ASCRXFCON_RXFEN);
-#endif
/* enable error signals */
SET_BIT(pAsc->asc_con, ASCCON_FEN);
SET_BIT(pAsc->asc_con, ASCCON_OEN);
-#ifdef CONFIG_INCA_IP
/* acknowledge ASC interrupts */
ASC_INTERRUPTS_CLEAR(INCAASC_IRQ_LINE_ALL);
/* disable ASC interrupts */
ASC_INTERRUPTS_DISABLE(INCAASC_IRQ_LINE_ALL);
-#endif
-#ifdef ASC_FIFO_PRESENT
/* set FIFOs into the transparent mode */
SET_BIT(pAsc->asc_txfcon, ASCTXFCON_TXTMEN);
SET_BIT(pAsc->asc_rxfcon, ASCRXFCON_RXTMEN);
-#endif
/* set baud rate */
serial_setbrg();
ulong uiReloadValue, fdv;
ulong f_ASC;
-#ifdef CONFIG_INCA_IP
f_ASC = incaip_get_fpiclk();
-#else
- f_ASC = ASC_CLOCK_RATE;
-#endif
#ifndef INCAASC_USE_FDV
fdv = 2;
void serial_putc (const char c)
{
-#ifdef ASC_FIFO_PRESENT
uint txFl = 0;
-#else
- uint timeout = 0;
-#endif
if (c == '\n') serial_putc ('\r');
-#ifdef ASC_FIFO_PRESENT
/* check do we have a free space in the TX FIFO */
/* get current filling level */
do
txFl = ( pAsc->asc_fstat & ASCFSTAT_TXFFLMASK ) >> ASCFSTAT_TXFFLOFF;
}
while ( txFl == INCAASC_TXFIFO_FULL );
-#else
-
- while(!(*(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) &
- FBS_ISR_AB))
- {
- if (timeout++ > TOUT_LOOP)
- {
- break;
- }
- }
-#endif
pAsc->asc_tbuf = c; /* write char to Transmit Buffer Register */
-#ifndef ASC_FIFO_PRESENT
- *(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) = FBS_ISR_AB |
- FBS_ISR_AT;
-#endif
-
/* check for errors */
if ( pAsc->asc_con & ASCCON_OE )
{
c = (char)(pAsc->asc_rbuf & symbol_mask);
-#ifndef ASC_FIFO_PRESENT
- *(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) = FBS_ISR_AR;
-#endif
-
return c;
}
{
int res = 1;
-#ifdef ASC_FIFO_PRESENT
if ( (pAsc->asc_fstat & ASCFSTAT_RXFFLMASK) == 0 )
{
res = 0;
}
-#else
- if (!(*(volatile unsigned long*)(SFPI_INTCON_BASEADDR + FBS_ISR) &
- FBS_ISR_AR))
-
- {
- res = 0;
- }
-#endif
else if ( pAsc->asc_con & ASCCON_FE )
{
SET_BIT(pAsc->asc_whbcon, ASCWHBCON_CLRFE);
* RETURNS: N/A
*
*/
-#if defined(CONFIG_PURPLE)
-# define CACHE_LOCK_SIZE (CONFIG_SYS_DCACHE_SIZE/2)
-#else
# define CACHE_LOCK_SIZE (CONFIG_SYS_DCACHE_SIZE)
-#endif
.globl mips_cache_lock
.ent mips_cache_lock
mips_cache_lock:
#if defined(CONFIG_INCA_IP)
.word INFINEON_EBU_BOOTCFG /* EBU init code, fetched during booting */
.word 0x00000000 /* phase of the flash */
-#elif defined(CONFIG_PURPLE)
- .word INFINEON_EBU_BOOTCFG /* EBU init code, fetched during booting */
- .word INFINEON_EBU_BOOTCFG /* EBU init code, fetched during booting */
#else
RVECENT(romReserved,2)
#endif
* 128 * 8 == 1024 == 0x400
* so this is address R_VEC+0x400 == 0xbfc00400
*/
-#ifdef CONFIG_PURPLE
-/* 0xbfc00400 */
- .word 0xdc870000
- .word 0xfca70000
- .word 0x20840008
- .word 0x20a50008
- .word 0x20c6ffff
- .word 0x14c0fffa
- .word 0x00000000
- .word 0x03e00008
- .word 0x00000000
- .word 0x00000000
-/* 0xbfc00428 */
- .word 0xdc870000
- .word 0xfca70000
- .word 0x20840008
- .word 0x20a50008
- .word 0x20c6ffff
- .word 0x14c0fffa
- .word 0x00000000
- .word 0x03e00008
- .word 0x00000000
- .word 0x00000000
-#endif /* CONFIG_PURPLE */
.align 4
reset:
move a0, t1 /* a0 <-- destination addr */
sub a1, t2, t0 /* a1 <-- size */
- /* On the purple board we copy the code earlier in a special way
- * in order to solve flash problems
- */
-#ifndef CONFIG_PURPLE
1:
lw t3, 0(t0)
sw t3, 0(t1)
addu t0, 4
ble t0, t2, 1b
addu t1, 4 /* delay slot */
-#endif
/* If caches were enabled, we would have to flush them here.
*/
/* Module : EBU register address and bits */
/***********************************************************************/
-#if defined(CONFIG_INCA_IP)
#define INCA_IP_EBU (0xB8000200)
-#elif defined(CONFIG_PURPLE)
-#define INCA_IP_EBU (0xB800D800)
-#endif
-
/***********************************************************************/
/* Module : ASC register address and bits */
/***********************************************************************/
-#if defined(CONFIG_INCA_IP)
#define INCA_IP_ASC (0xB8000400)
-#elif defined(CONFIG_PURPLE)
-#define INCA_IP_ASC (0xBE500000)
-#endif
-
/***********************************************************************/
init_fnc_t **init_fnc_ptr;
ulong addr, addr_sp, len = (ulong)&uboot_end - CONFIG_SYS_MONITOR_BASE;
ulong *s;
-#ifdef CONFIG_PURPLE
- void copy_code (ulong);
-#endif
/* Pointer is writable since we allocated a register for it.
*/
memcpy (id, (void *)gd, sizeof (gd_t));
- /* On the purple board we copy the code in a special way
- * in order to solve flash problems
- */
-#ifdef CONFIG_PURPLE
- copy_code(addr);
-#endif
-
relocate_code (addr_sp, id, addr);
/* NOTREACHED - relocate_code() does not return */
+++ /dev/null
-
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).o
-
-COBJS = $(BOARD).o flash.o sconsole.o
-SOBJS = lowlevel_init.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS) $(SOBJS)
- $(call cmd_link_o_target, $(OBJS))
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-#
-# (C) Copyright 2003
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-#
-# Purple board with MIPS 5Kc CPU core
-#
-
-# ROM version
-CONFIG_SYS_TEXT_BASE = 0xB0000000
-
-# RAM version
-#CONFIG_SYS_TEXT_BASE = 0x80100000
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/inca-ip.h>
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-typedef unsigned long FLASH_PORT_WIDTH;
-typedef volatile unsigned long FLASH_PORT_WIDTHV;
-
-#define FLASH_ID_MASK 0xFFFFFFFF
-
-#define FPW FLASH_PORT_WIDTH
-#define FPWV FLASH_PORT_WIDTHV
-
-#define ORMASK(size) ((-size) & OR_AM_MSK)
-
-#define FLASH29_REG_ADRS(reg) ((FPWV *)PHYS_FLASH_1 + (reg))
-
-/* FLASH29 command register addresses */
-
-#define FLASH29_REG_FIRST_CYCLE FLASH29_REG_ADRS (0x1555)
-#define FLASH29_REG_SECOND_CYCLE FLASH29_REG_ADRS (0x2aaa)
-#define FLASH29_REG_THIRD_CYCLE FLASH29_REG_ADRS (0x3555)
-#define FLASH29_REG_FOURTH_CYCLE FLASH29_REG_ADRS (0x4555)
-#define FLASH29_REG_FIFTH_CYCLE FLASH29_REG_ADRS (0x5aaa)
-#define FLASH29_REG_SIXTH_CYCLE FLASH29_REG_ADRS (0x6555)
-
-/* FLASH29 command definitions */
-
-#define FLASH29_CMD_FIRST 0xaaaaaaaa
-#define FLASH29_CMD_SECOND 0x55555555
-#define FLASH29_CMD_FOURTH 0xaaaaaaaa
-#define FLASH29_CMD_FIFTH 0x55555555
-#define FLASH29_CMD_SIXTH 0x10101010
-
-#define FLASH29_CMD_SECTOR 0x30303030
-#define FLASH29_CMD_PROGRAM 0xa0a0a0a0
-#define FLASH29_CMD_CHIP_ERASE 0x80808080
-#define FLASH29_CMD_READ_RESET 0xf0f0f0f0
-#define FLASH29_CMD_AUTOSELECT 0x90909090
-#define FLASH29_CMD_READ 0x70707070
-
-#define IN_RAM_CMD_READ 0x1
-#define IN_RAM_CMD_WRITE 0x2
-
-#define FLASH_WRITE_CMD ((ulong)(flash_write_cmd) & 0x7)+0xbf008000
-#define FLASH_READ_CMD ((ulong)(flash_read_cmd) & 0x7)+0xbf008000
-
-typedef void (*FUNCPTR_CP)(ulong *source, ulong *destination, ulong nlongs);
-typedef void (*FUNCPTR_RD)(int cmd, FPWV * pFA, char * string, int strLen);
-typedef void (*FUNCPTR_WR)(int cmd, FPWV * pFA, FPW value);
-
-static ulong flash_get_size(FPWV *addr, flash_info_t *info);
-static int write_word(flash_info_t *info, FPWV *dest, FPW data);
-static void flash_get_offsets(ulong base, flash_info_t *info);
-static flash_info_t *flash_get_info(ulong base);
-
-static void load_cmd(ulong cmd);
-static ulong in_ram_cmd = 0;
-
-
-/******************************************************************************
-*
-* Don't change the program architecture
-* This architecture assure the program
-* can be relocated to scratch ram
-*/
-static void flash_read_cmd(int cmd, FPWV * pFA, char * string, int strLen)
-{
- int i,j;
- FPW temp,temp1;
- FPWV *str;
-
- str = (FPWV *)string;
-
- j= strLen/4;
-
- if(cmd == FLASH29_CMD_AUTOSELECT)
- {
- *(FLASH29_REG_FIRST_CYCLE) = FLASH29_CMD_FIRST;
- *(FLASH29_REG_SECOND_CYCLE) = FLASH29_CMD_SECOND;
- *(FLASH29_REG_THIRD_CYCLE) = FLASH29_CMD_AUTOSELECT;
- }
-
- if(cmd == FLASH29_CMD_READ)
- {
- i = 0;
- while(i<j)
- {
- temp = *pFA++;
- temp1 = *(int *)0xa0000000;
- *(int *)0xbf0081f8 = temp1 + temp;
- *str++ = temp;
- i++;
- }
- }
-
- if(cmd == FLASH29_CMD_READ_RESET)
- {
- *(FLASH29_REG_FIRST_CYCLE) = FLASH29_CMD_FIRST;
- *(FLASH29_REG_SECOND_CYCLE) = FLASH29_CMD_SECOND;
- *(FLASH29_REG_THIRD_CYCLE) = FLASH29_CMD_READ_RESET;
- }
-
- *(int *)0xbf0081f8 = *(int *)0xa0000000; /* dummy read switch back to sdram interface */
-}
-
-/******************************************************************************
-*
-* Don't change the program architecture
-* This architecture assure the program
-* can be relocated to scratch ram
-*/
-static void flash_write_cmd(int cmd, FPWV * pFA, FPW value)
-{
- *(FLASH29_REG_FIRST_CYCLE) = FLASH29_CMD_FIRST;
- *(FLASH29_REG_SECOND_CYCLE) = FLASH29_CMD_SECOND;
-
- if (cmd == FLASH29_CMD_SECTOR)
- {
- *(FLASH29_REG_THIRD_CYCLE) = FLASH29_CMD_CHIP_ERASE;
- *(FLASH29_REG_FOURTH_CYCLE) = FLASH29_CMD_FOURTH;
- *(FLASH29_REG_FIFTH_CYCLE) = FLASH29_CMD_FIFTH;
- *pFA = FLASH29_CMD_SECTOR;
- }
-
- if (cmd == FLASH29_CMD_SIXTH)
- {
- *(FLASH29_REG_THIRD_CYCLE) = FLASH29_CMD_CHIP_ERASE;
- *(FLASH29_REG_FOURTH_CYCLE) = FLASH29_CMD_FOURTH;
- *(FLASH29_REG_FIFTH_CYCLE) = FLASH29_CMD_FIFTH;
- *(FLASH29_REG_SIXTH_CYCLE) = FLASH29_CMD_SIXTH;
- }
-
- if (cmd == FLASH29_CMD_PROGRAM)
- {
- *(FLASH29_REG_THIRD_CYCLE) = FLASH29_CMD_PROGRAM;
- *pFA = value;
- }
-
- if (cmd == FLASH29_CMD_READ_RESET)
- {
- *(FLASH29_REG_THIRD_CYCLE) = FLASH29_CMD_READ_RESET;
- }
-
- *(int *)0xbf0081f8 = *(int *)0xa0000000; /* dummy read switch back to sdram interface */
-}
-
-static void load_cmd(ulong cmd)
-{
- ulong *src;
- ulong *dst;
- FUNCPTR_CP absEntry;
- ulong func;
-
- if (in_ram_cmd & cmd) return;
-
- if (cmd == IN_RAM_CMD_READ)
- {
- func = (ulong)flash_read_cmd;
- }
- else
- {
- func = (ulong)flash_write_cmd;
- }
-
- src = (ulong *)(func & 0xfffffff8);
- dst = (ulong *)0xbf008000;
- absEntry = (FUNCPTR_CP)(0xbf0081d0);
- absEntry(src,dst,0x38);
-
- in_ram_cmd = cmd;
-}
-
-/*-----------------------------------------------------------------------
- * flash_init()
- *
- * sets up flash_info and returns size of FLASH (bytes)
- */
-unsigned long flash_init (void)
-{
- unsigned long size = 0;
- int i;
-
- load_cmd(IN_RAM_CMD_READ);
-
- /* Init: no FLASHes known */
- for (i=0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- ulong flashbase = PHYS_FLASH_1;
- ulong * buscon = (ulong *) INCA_IP_EBU_EBU_BUSCON0;
-
- /* Disable write protection */
- *buscon &= ~INCA_IP_EBU_EBU_BUSCON1_WRDIS;
-
-#if 1
- memset(&flash_info[i], 0, sizeof(flash_info_t));
-#endif
-
- flash_info[i].size =
- flash_get_size((FPW *)flashbase, &flash_info[i]);
-
- if (flash_info[i].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank %d - Size = 0x%08lx\n",
- i, flash_info[i].size);
- }
-
- size += flash_info[i].size;
- }
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- flash_get_info(CONFIG_SYS_MONITOR_BASE));
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SIZE-1,
- flash_get_info(CONFIG_ENV_ADDR));
-#endif
-
- return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
- int i;
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD
- && (info->flash_id & FLASH_TYPEMASK) == FLASH_AM160B) {
-
- int bootsect_size[4]; /* number of bytes/boot sector */
- int sect_size; /* number of bytes/regular sector */
-
- bootsect_size[0] = 0x00008000;
- bootsect_size[1] = 0x00004000;
- bootsect_size[2] = 0x00004000;
- bootsect_size[3] = 0x00010000;
- sect_size = 0x00020000;
-
- /* set sector offsets for bottom boot block type */
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base;
- base += i < 4 ? bootsect_size[i] : sect_size;
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-
-static flash_info_t *flash_get_info(ulong base)
-{
- int i;
- flash_info_t * info;
-
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i ++) {
- info = & flash_info[i];
- if (info->start[0] <= base && base < info->start[0] + info->size)
- break;
- }
-
- return i == CONFIG_SYS_MAX_FLASH_BANKS ? 0 : info;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-void flash_print_info (flash_info_t *info)
-{
- int i;
- uchar *boottype;
- uchar *bootletter;
- char *fmt;
- uchar botbootletter[] = "B";
- uchar topbootletter[] = "T";
- uchar botboottype[] = "bottom boot sector";
- uchar topboottype[] = "top boot sector";
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD: printf ("AMD "); break;
- case FLASH_MAN_BM: printf ("BRIGHT MICRO "); break;
- case FLASH_MAN_FUJ: printf ("FUJITSU "); break;
- case FLASH_MAN_SST: printf ("SST "); break;
- case FLASH_MAN_STM: printf ("STM "); break;
- case FLASH_MAN_INTEL: printf ("INTEL "); break;
- default: printf ("Unknown Vendor "); break;
- }
-
- /* check for top or bottom boot, if it applies */
- if (info->flash_id & FLASH_BTYPE) {
- boottype = botboottype;
- bootletter = botbootletter;
- }
- else {
- boottype = topboottype;
- bootletter = topbootletter;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM160B:
- fmt = "29LV160B%s (16 Mbit, %s)\n";
- break;
- case FLASH_28F800C3B:
- case FLASH_28F800C3T:
- fmt = "28F800C3%s (8 Mbit, %s)\n";
- break;
- case FLASH_INTEL800B:
- case FLASH_INTEL800T:
- fmt = "28F800B3%s (8 Mbit, %s)\n";
- break;
- case FLASH_28F160C3B:
- case FLASH_28F160C3T:
- fmt = "28F160C3%s (16 Mbit, %s)\n";
- break;
- case FLASH_INTEL160B:
- case FLASH_INTEL160T:
- fmt = "28F160B3%s (16 Mbit, %s)\n";
- break;
- case FLASH_28F320C3B:
- case FLASH_28F320C3T:
- fmt = "28F320C3%s (32 Mbit, %s)\n";
- break;
- case FLASH_INTEL320B:
- case FLASH_INTEL320T:
- fmt = "28F320B3%s (32 Mbit, %s)\n";
- break;
- case FLASH_28F640C3B:
- case FLASH_28F640C3T:
- fmt = "28F640C3%s (64 Mbit, %s)\n";
- break;
- case FLASH_INTEL640B:
- case FLASH_INTEL640T:
- fmt = "28F640B3%s (64 Mbit, %s)\n";
- break;
- default:
- fmt = "Unknown Chip Type\n";
- break;
- }
-
- printf (fmt, bootletter, boottype);
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20,
- info->sector_count);
-
- printf (" Sector Start Addresses:");
-
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0) {
- printf ("\n ");
- }
-
- printf (" %08lX%s", info->start[i],
- info->protect[i] ? " (RO)" : " ");
- }
-
- printf ("\n");
-}
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-ulong flash_get_size (FPWV *addr, flash_info_t *info)
-{
- FUNCPTR_RD absEntry;
- FPW retValue;
- int flag;
-
- load_cmd(IN_RAM_CMD_READ);
- absEntry = (FUNCPTR_RD)FLASH_READ_CMD;
-
- flag = disable_interrupts();
- absEntry(FLASH29_CMD_AUTOSELECT,0,0,0);
- if (flag) enable_interrupts();
-
- udelay(100);
-
- flag = disable_interrupts();
- absEntry(FLASH29_CMD_READ, addr + 1, (char *)&retValue, sizeof(retValue));
- absEntry(FLASH29_CMD_READ_RESET,0,0,0);
- if (flag) enable_interrupts();
-
- udelay(100);
-
- switch (retValue) {
-
- case (FPW)AMD_ID_LV160B:
- info->flash_id += FLASH_AM160B;
- info->sector_count = 35;
- info->size = 0x00400000;
- break; /* => 8 or 16 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- return (0); /* => no or unknown flash */
- }
-
- flash_get_offsets((ulong)addr, info);
-
- return (info->size);
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- FPWV *addr;
- int flag, prot, sect;
- ulong start, now, last;
- FUNCPTR_WR absEntry;
-
- load_cmd(IN_RAM_CMD_WRITE);
- absEntry = (FUNCPTR_WR)FLASH_WRITE_CMD;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM160B:
- break;
- case FLASH_UNKNOWN:
- default:
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- last = get_timer(0);
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
-
- if (info->protect[sect] != 0) /* protected, skip it */
- continue;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr = (FPWV *)(info->start[sect]);
- absEntry(FLASH29_CMD_SECTOR, addr, 0);
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- start = get_timer(0);
-
- while ((now = get_timer(start)) <= CONFIG_SYS_FLASH_ERASE_TOUT) {
-
- /* show that we're waiting */
- if ((get_timer(last)) > CONFIG_SYS_HZ) {/* every second */
- putc ('.');
- last = get_timer(0);
- }
- }
-
- flag = disable_interrupts();
- absEntry(FLASH29_CMD_READ_RESET,0,0);
- if (flag)
- enable_interrupts();
- }
-
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- FPW data = 0; /* 16 or 32 bit word, matches flash bus width on MPC8XX */
- int bytes; /* number of bytes to program in current word */
- int left; /* number of bytes left to program */
- int i, res;
-
- for (left = cnt, res = 0;
- left > 0 && res == 0;
- addr += sizeof(data), left -= sizeof(data) - bytes) {
-
- bytes = addr & (sizeof(data) - 1);
- addr &= ~(sizeof(data) - 1);
-
- /* combine source and destination data so can program
- * an entire word of 16 or 32 bits
- */
- for (i = 0; i < sizeof(data); i++) {
- data <<= 8;
- if (i < bytes || i - bytes >= left )
- data += *((uchar *)addr + i);
- else
- data += *src++;
- }
-
- res = write_word(info, (FPWV *)addr, data);
- }
-
- return (res);
-}
-
-static int write_word (flash_info_t *info, FPWV *dest, FPW data)
-{
- int res = 0; /* result, assume success */
- FUNCPTR_WR absEntry;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*dest & data) != data) {
- return (2);
- }
-
- if (info->start[0] != PHYS_FLASH_1)
- {
- return (3);
- }
-
- load_cmd(IN_RAM_CMD_WRITE);
- absEntry = (FUNCPTR_WR)FLASH_WRITE_CMD;
-
- flag = disable_interrupts();
- absEntry(FLASH29_CMD_PROGRAM,dest,data);
- if (flag) enable_interrupts();
-
- udelay(100);
-
- flag = disable_interrupts();
- absEntry(FLASH29_CMD_READ_RESET,0,0);
- if (flag) enable_interrupts();
-
- return (res);
-}
+++ /dev/null
-/*
- * Memory sub-system initialization code for PURPLE development board.
- *
- * Copyright (c) 2003 Wolfgang Denk <wd@denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <asm/regdef.h>
-
-#define MC_IOGP 0xBF800800
-
- .globl lowlevel_init
-lowlevel_init:
- li t0, MC_IOGP
- li t1, 0xf24
- sw t1, 0(t0)
- jr ra
- nop
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <command.h>
-#include <netdev.h>
-#include <asm/inca-ip.h>
-#include <asm/regdef.h>
-#include <asm/mipsregs.h>
-#include <asm/io.h>
-#include <asm/addrspace.h>
-#include <asm/cacheops.h>
-#include <asm/reboot.h>
-
-#include "sconsole.h"
-
-#define cache_unroll(base,op) \
- __asm__ __volatile__(" \
- .set noreorder; \
- .set mips3; \
- cache %1, (%0); \
- .set mips0; \
- .set reorder" \
- : \
- : "r" (base), \
- "i" (op));
-
-typedef void (*FUNCPTR)(ulong *source, ulong *destination, ulong nlongs);
-
-extern void asc_serial_init (void);
-extern void asc_serial_putc (char);
-extern void asc_serial_puts (const char *);
-extern int asc_serial_getc (void);
-extern int asc_serial_tstc (void);
-extern void asc_serial_setbrg (void);
-
-void _machine_restart(void)
-{
- void (*f)(void) = (void *) 0xbfc00000;
-
- f();
-}
-
-static void sdram_timing_init (ulong size)
-{
- register uint pass;
- register uint done;
- register uint count;
- register uint p0, p1, p2, p3, p4;
- register uint addr;
-
-#define WRITE_MC_IOGP_1 *(uint *)0xbf800800 = (p1<<14)+(p2<<13)+(p4<<8)+(p0<<4)+p3;
-#define WRITE_MC_IOGP_2 *(uint *)0xbf800800 = (p1<<14)+(p2<<13)+((p4-16)<<8)+(p0<<4)+p3;
-
- done = 0;
- p0 = 2;
- while (p0 < 4 && done == 0) {
- p1 = 0;
- while (p1 < 2 && done == 0) {
- p2 = 0;
- while (p2 < 2 && done == 0) {
- p3 = 0;
- while (p3 < 16 && done == 0) {
- count = 0;
- p4 = 0;
- while (p4 < 32 && done == 0) {
- WRITE_MC_IOGP_1;
-
- for (addr = CKSEG1 + 0x4000;
- addr < CKSEG1ADDR (size);
- addr = addr + 4) {
- *(uint *) addr = 0xaa55aa55;
- }
-
- pass = 1;
-
- for (addr = CKSEG1 + 0x4000;
- addr < CKSEG1ADDR (size) && pass == 1;
- addr = addr + 4) {
- if (*(uint *) addr != 0xaa55aa55)
- pass = 0;
- }
-
- if (pass == 1) {
- count++;
- } else {
- count = 0;
- }
-
- if (count == 32) {
- WRITE_MC_IOGP_2;
- done = 1;
- }
- p4++;
- }
- p3++;
- }
- p2++;
- }
- p1++;
- }
- p0++;
- if (p0 == 1)
- p0++;
- }
-}
-
-phys_size_t initdram(int board_type)
-{
- /* The only supported number of SDRAM banks is 4.
- */
-#define CONFIG_SYS_NB 4
-
- ulong cfgpb0 = *INCA_IP_SDRAM_MC_CFGPB0;
- ulong cfgdw = *INCA_IP_SDRAM_MC_CFGDW;
- int cols = cfgpb0 & 0xF;
- int rows = (cfgpb0 & 0xF0) >> 4;
- int dw = cfgdw & 0xF;
- ulong size = (1 << (rows + cols)) * (1 << (dw - 1)) * CONFIG_SYS_NB;
- void (* sdram_init) (ulong);
-
- sdram_init = (void (*)(ulong)) CKSEG0ADDR(&sdram_timing_init);
-
- sdram_init(0x10000);
-
- return size;
-}
-
-int checkboard (void)
-{
-
- unsigned long chipid = *(unsigned long *)0xB800C800;
-
- printf ("Board: Purple PLB 2800 chip version %ld, ", chipid & 0xF);
-
- printf("CPU Speed %d MHz\n", CPU_CLOCK_RATE/1000000);
-
- set_io_port_base(0);
-
- return 0;
-}
-
-int misc_init_r (void)
-{
- asc_serial_init ();
-
- sconsole_putc = asc_serial_putc;
- sconsole_puts = asc_serial_puts;
- sconsole_getc = asc_serial_getc;
- sconsole_tstc = asc_serial_tstc;
- sconsole_setbrg = asc_serial_setbrg;
-
- sconsole_flush ();
- return (0);
-}
-
-/*******************************************************************************
-*
-* copydwords - copy one buffer to another a long at a time
-*
-* This routine copies the first <nlongs> longs from <source> to <destination>.
-*/
-static void copydwords (ulong *source, ulong *destination, ulong nlongs)
-{
- ulong temp,temp1;
- ulong *dstend = destination + nlongs;
-
- while (destination < dstend) {
- temp = *source++;
- /* dummy read from sdram */
- temp1 = *(ulong *)0xa0000000;
- /* avoid optimization from compliler */
- *(ulong *)0xbf0081f8 = temp1 + temp;
- *destination++ = temp;
-
- }
-}
-
-/*******************************************************************************
-*
-* copyLongs - copy one buffer to another a long at a time
-*
-* This routine copies the first <nlongs> longs from <source> to <destination>.
-*/
-static void copyLongs (ulong *source, ulong *destination, ulong nlongs)
-{
- FUNCPTR absEntry;
-
- absEntry = (FUNCPTR)(0xbf008000+((ulong)copydwords & 0x7));
- absEntry(source, destination, nlongs);
-}
-
-/*******************************************************************************
-*
-* programLoad - load program into ram
-*
-* This routine load copydwords into ram
-*
-*/
-static void programLoad(void)
-{
- FUNCPTR absEntry;
- ulong *src,*dst;
-
- src = (ulong *)(CONFIG_SYS_TEXT_BASE + 0x428);
- dst = (ulong *)0xbf0081d0;
-
- absEntry = (FUNCPTR)(CONFIG_SYS_TEXT_BASE + 0x400);
- absEntry(src,dst,0x6);
-
- src = (ulong *)((ulong)copydwords & 0xfffffff8);
- dst = (ulong *)0xbf008000;
-
- absEntry(src,dst,0x38);
-}
-
-/*******************************************************************************
-*
-* copy_code - copy u-boot image from flash to RAM
-*
-* This routine is needed to solve flash problems on this board
-*
-*/
-void copy_code (ulong dest_addr)
-{
- extern long uboot_end_data;
- unsigned long start;
- unsigned long end;
-
- /* load copydwords into ram
- */
- programLoad();
-
- /* copy u-boot code
- */
- copyLongs((ulong *)CONFIG_SYS_MONITOR_BASE,
- (ulong *)dest_addr,
- ((ulong)&uboot_end_data - CONFIG_SYS_MONITOR_BASE + 3) / 4);
-
-
- /* flush caches
- */
-
- start = CKSEG0;
- end = start + CONFIG_SYS_DCACHE_SIZE;
- while(start < end) {
- cache_unroll(start,Index_Writeback_Inv_D);
- start += CONFIG_SYS_CACHELINE_SIZE;
- }
-
- start = CKSEG0;
- end = start + CONFIG_SYS_ICACHE_SIZE;
- while(start < end) {
- cache_unroll(start,Index_Invalidate_I);
- start += CONFIG_SYS_CACHELINE_SIZE;
- }
-}
-
-#ifdef CONFIG_PLB2800_ETHER
-int board_eth_init(bd_t *bis)
-{
- return plb2800_eth_initialize(bis);
-}
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <common.h>
-
-#include "sconsole.h"
-
-void (*sconsole_putc) (char) = 0;
-void (*sconsole_puts) (const char *) = 0;
-int (*sconsole_getc) (void) = 0;
-int (*sconsole_tstc) (void) = 0;
-void (*sconsole_setbrg) (void) = 0;
-
-int serial_init (void)
-{
- sconsole_buffer_t *sb = SCONSOLE_BUFFER;
-
- sb->pos = 0;
- sb->size = 0;
- sb->max_size = CONFIG_SYS_SCONSOLE_SIZE - sizeof (sconsole_buffer_t);
-
- return (0);
-}
-
-void serial_putc (char c)
-{
- if (sconsole_putc) {
- (*sconsole_putc) (c);
- } else {
- sconsole_buffer_t *sb = SCONSOLE_BUFFER;
-
- if (c) {
- sb->data[sb->pos++] = c;
- if (sb->pos == sb->max_size) {
- sb->pos = 0;
- }
- if (sb->size < sb->max_size) {
- sb->size++;
- }
- }
- }
-}
-
-void serial_puts (const char *s)
-{
- if (sconsole_puts) {
- (*sconsole_puts) (s);
- } else {
- sconsole_buffer_t *sb = SCONSOLE_BUFFER;
-
- while (*s) {
- sb->data[sb->pos++] = *s++;
- if (sb->pos == sb->max_size) {
- sb->pos = 0;
- }
- if (sb->size < sb->max_size) {
- sb->size++;
- }
- }
- }
-}
-
-int serial_getc (void)
-{
- if (sconsole_getc) {
- return (*sconsole_getc) ();
- } else {
- return 0;
- }
-}
-
-int serial_tstc (void)
-{
- if (sconsole_tstc) {
- return (*sconsole_tstc) ();
- } else {
- return 0;
- }
-}
-
-void serial_setbrg (void)
-{
- if (sconsole_setbrg) {
- (*sconsole_setbrg) ();
- }
-}
-
-void sconsole_flush (void)
-{
- if (sconsole_putc) {
- sconsole_buffer_t *sb = SCONSOLE_BUFFER;
- unsigned int end = sb->pos < sb->size
- ? sb->pos + sb->max_size - sb->size
- : sb->pos - sb->size;
-
- while (sb->size) {
- (*sconsole_putc) (sb->data[end++]);
- if (end == sb->max_size) {
- end = 0;
- }
- sb->size--;
- }
- }
-}
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef _SCONSOLE_H_
-#define _SCONSOLE_H_
-
-#include <config.h>
-
-typedef struct sconsole_buffer_s {
- unsigned long size;
- unsigned long max_size;
- unsigned long pos;
- char data[1];
-} sconsole_buffer_t;
-
-#define SCONSOLE_BUFFER ((sconsole_buffer_t *) CONFIG_SYS_SCONSOLE_ADDR)
-
-extern void (* sconsole_putc) (char);
-extern void (* sconsole_puts) (const char *);
-extern int (* sconsole_getc) (void);
-extern int (* sconsole_tstc) (void);
-extern void (* sconsole_setbrg) (void);
-
-extern void sconsole_flush (void);
-
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk Engineering, <wd@denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
-OUTPUT_FORMAT("elf32-bigmips", "elf32-bigmips", "elf32-bigmips")
-*/
-OUTPUT_FORMAT("elf32-tradbigmips", "elf32-tradbigmips", "elf32-tradlittlemips")
-OUTPUT_ARCH(mips)
-ENTRY(_start)
-SECTIONS
-{
- . = 0x00000000;
-
- . = ALIGN(4);
- .text :
- {
- arch/mips/cpu/start.o (.text)
- board/purple/lowlevel_init.o (.text)
- . = DEFINED(env_offset) ? env_offset : .;
- common/env_embedded.o (.ppcenv)
-
- *(.text)
- }
-
- . = ALIGN(4);
- .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
-
- . = ALIGN(4);
- .data : { *(.data) }
-
- . = .;
- _gp = ALIGN(16) + 0x7ff0;
-
- .got : {
- __got_start = .;
- *(.got)
- __got_end = .;
- }
-
- .sdata : { *(.sdata) }
-
- .u_boot_cmd : {
- __u_boot_cmd_start = .;
- *(.u_boot_cmd)
- __u_boot_cmd_end = .;
- }
-
- uboot_end_data = .;
- num_got_entries = (__got_end - __got_start) >> 2;
-
- . = ALIGN(4);
- .sbss (NOLOAD) : { *(.sbss) }
- .bss (NOLOAD) : { *(.bss) . = ALIGN(4); }
- uboot_end = .;
-}
incaip_133MHz mips mips incaip - - incaip:CPU_CLOCK_RATE=133000000
incaip_150MHz mips mips incaip - - incaip:CPU_CLOCK_RATE=150000000
pb1000 mips mips pb1x00 - - pb1x00:PB1000
-purple mips mips
qemu_mips mips mips qemu-mips - - qemu-mips
tb0229 mips mips
vct_premium mips mips vct micronas - vct:VCT_PREMIUM
+++ /dev/null
-Installation Instructions:
---------------------------
-
-1. Put the s2 switch into the following position:
-
- Off On
- ------
- |x |
- | x|
- |x |
- | X|
- ------
-
- Put the s3 switch into the following position:
-
- Off On
- ------
- | x |
- | x |
- | x|
- | x|
- ------
-
- Put the s4 switch into the following position:
-
- Off On
- ------
- |x |
- |x |
- |x |
- |x |
- |x |
- | x|
- | x|
- |x |
- ------
-
-2. Connect to the serial console and to the BDI. Power on. On the
- serial line, you should see:
-
- PURPLE@1.2>
-
-3. Type '8'. No echo will be displayed. In response, you should get:
-
- 7A(pass)
-
-4. From BDI, enter command:
-
- mmw 0xb800d860 0x0042c7ff
-
-5. Then, from BDI:
-
- erase 0xB0000000
- erase 0xB0008000
- erase 0xB000C000
- erase 0xB0010000
- erase 0xB0020000
-
- prog 0xB0000000 <u-boot.bin> bin
-
-6. Power off. Restore the original S2 switch position:
-
- Off On
- ------
- | x|
- | x|
- |x |
- | X|
- ------
-
- Power on. U-Boot should come up.
-
-
-Implementation Notes:
----------------------
-
-Due to the RAM/flash bus arbitration problem the suggested workaround
-had to be implemented. It works okay. On the downside is that you
-can't really check whether 'erase' is complete by polling flash as it
-is usually done. Instead, the flash driver simply waits for a given
-time and assumes that erase then has passed. This behaviour is
-identical to what the VxWorks driver does; also, the same timeout (6
-seconds) was chosen. Note that this timeout applies for each erase
-operation, i. e. per erased sector.
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * This file contains the configuration parameters for the PURPLE board.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_MIPS32 1 /* MIPS 5Kc CPU core */
-#define CONFIG_PURPLE 1 /* on a PURPLE Board */
-
-#define CPU_CLOCK_RATE 125000000 /* 125 MHz clock for the MIPS core */
-#define ASC_CLOCK_RATE 62500000 /* 62.5 MHz ASC clock */
-
-#define INFINEON_EBU_BOOTCFG 0xE0CC
-
-#define CONFIG_STACKSIZE (128 * 1024)
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_BAUDRATE 19200
-
-/* valid baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off\0" \
- "addmisc=setenv bootargs ${bootargs} " \
- "console=ttyS0,${baudrate} " \
- "ethaddr=${ethaddr} " \
- "panic=1\0" \
- "flash_nfs=run nfsargs addip addmisc;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 80500000 ${bootfile};" \
- "run nfsargs addip addmisc;bootm\0" \
- "rootpath=/opt/eldk/mips_5KC\0" \
- "bootfile=/tftpboot/purple/uImage\0" \
- "kernel_addr=B0040000\0" \
- "ramdisk_addr=B0100000\0" \
- "u-boot=/tftpboot/purple/u-boot.bin\0" \
- "load=tftp 80500000 ${u-boot}\0" \
- "update=protect off 1:0-4;era 1:0-4;" \
- "cp.b 80500000 B0000000 ${filesize}\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-
-
-#define CONFIG_SYS_SDRAM_BASE 0x80000000
-
-#define CONFIG_SYS_INIT_SP_OFFSET 0x400000
-
-#define CONFIG_SYS_MALLOC_LEN 128*1024
-
-#define CONFIG_SYS_BOOTPARAMS_LEN 128*1024
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "PURPLE # " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MIPS_TIMER_FREQ (CPU_CLOCK_RATE/2)
-#define CONFIG_SYS_HZ 1000
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args*/
-
-#define CONFIG_SYS_LOAD_ADDR 0x80500000 /* default load address */
-
-#define CONFIG_SYS_MEMTEST_START 0x80200000
-#define CONFIG_SYS_MEMTEST_END 0x80800000
-
-#define CONFIG_MISC_INIT_R
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT (35) /* max number of sectors on one chip */
-
-#define PHYS_FLASH_1 0xb0000000 /* Flash Bank #1 */
-
-/* The following #defines are needed to get flash environment right */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (192 << 10)
-
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (6 * CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (6 * CONFIG_SYS_HZ) /* Timeout for Flash Write */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-
-/* Address and size of Primary Environment Sector */
-#define CONFIG_ENV_ADDR 0xB0008000
-#define CONFIG_ENV_SIZE 0x4000
-
-#define CONFIG_FLASH_32BIT
-#define CONFIG_NR_DRAM_BANKS 1
-
-#define CONFIG_PLB2800_ETHER
-#define CONFIG_NET_MULTI
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_DCACHE_SIZE 16384
-#define CONFIG_SYS_ICACHE_SIZE 16384
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
-/*
- * Temporary buffer for serial data until the real serial driver
- * is initialised (memtest will destroy this buffer)
- */
-#define CONFIG_SYS_SCONSOLE_ADDR (CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_INIT_SP_OFFSET - \
- CONFIG_SYS_DCACHE_SIZE / 2)
-#define CONFIG_SYS_SCONSOLE_SIZE (CONFIG_SYS_DCACHE_SIZE / 4)
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff