Auto-size RAM on canmb board.

Cleanup.

diff --git a/CHANGELOG b/CHANGELOG
index 28d35e28fd19f3294c6ec09217cdcacecd20925f..ba5e3dd14ef2b0ba2a8f83d825fc9856b6b3eded 100644 (file)
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -6,6 +6,8 @@ Changes for U-Boot 1.1.3:
   Make PCI target address spaces on PMC405 and CPCI405 boards
   configurable via environment variables
 
+* Auto-size RAM on canmb board.
+
 * Add support for canmb board
 
 * Patch by Stefan Roese, 13 Apr 2005:

diff --git a/board/canmb/canmb.c b/board/canmb/canmb.c
index 172fcd7bc7cf2de29ca7d439b4801e8cdebc2b5b..3d3abf72074f7a9d632e2b194dc8abf877a46305 100644 (file)
--- a/board/canmb/canmb.c
+++ b/board/canmb/canmb.c
@@ -2,8 +2,8 @@
  * (C) Copyright 2005
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
- * (C) Copyright 2003
- * Reinhard Meyer, EMK Elektronik GmbH, r.meyer@emk-elektronik.de
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -28,64 +28,209 @@
 #include <mpc5xxx.h>
 #include <pci.h>
 
-/*****************************************************************************
- * initialize SDRAM/DDRAM controller.
- * TBD: get data from I2C EEPROM
- *****************************************************************************/
-long int initdram (int board_type)
-{
-       ulong dramsize = 0;
-#ifndef CFG_RAMBOOT
-#if 0
-       ulong   t;
-       ulong   tap_del;
+#if defined(CONFIG_MPC5200_DDR)
+#include "mt46v16m16-75.h"
+#else
+#include "mt48lc16m32s2-75.h"
 #endif
 
-       #define MODE_EN         0x80000000
-       #define SOFT_PRE        2
-       #define SOFT_REF        4
-
-       /* configure SDRAM start/end */
-       *(vu_long *)MPC5XXX_SDRAM_CS0CFG = (CFG_SDRAM_BASE & 0xFFF00000) | CFG_DRAM_RAM_SIZE;
-       *(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x8000000;
-
-       /* setup config registers */
-       *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = CFG_DRAM_CONFIG1;
-       *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = CFG_DRAM_CONFIG2;
+#ifndef CFG_RAMBOOT
+static void sdram_start (int hi_addr)
+{
+       long hi_addr_bit = hi_addr ? 0x01000000 : 0;
 
        /* unlock mode register */
-       *(vu_long *)MPC5XXX_SDRAM_CTRL = CFG_DRAM_CONTROL | MODE_EN;
+       *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
+       __asm__ volatile ("sync");
+
        /* precharge all banks */
-       *(vu_long *)MPC5XXX_SDRAM_CTRL = CFG_DRAM_CONTROL | MODE_EN | SOFT_PRE;
-#ifdef CFG_DRAM_DDR
-       /* set extended mode register */
-       *(vu_short *)MPC5XXX_SDRAM_MODE = CFG_DRAM_EMODE;
+       *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+       __asm__ volatile ("sync");
+
+#if SDRAM_DDR
+       /* set mode register: extended mode */
+       *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
+       __asm__ volatile ("sync");
+
+       /* set mode register: reset DLL */
+       *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
+       __asm__ volatile ("sync");
 #endif
-       /* set mode register */
-       *(vu_short *)MPC5XXX_SDRAM_MODE = CFG_DRAM_MODE | 0x0400;
+
        /* precharge all banks */
-       *(vu_long *)MPC5XXX_SDRAM_CTRL = CFG_DRAM_CONTROL | MODE_EN | SOFT_PRE;
+       *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+       __asm__ volatile ("sync");
+
        /* auto refresh */
-       *(vu_long *)MPC5XXX_SDRAM_CTRL = CFG_DRAM_CONTROL | MODE_EN | SOFT_REF;
+       *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
+       __asm__ volatile ("sync");
+
        /* set mode register */
-       *(vu_short *)MPC5XXX_SDRAM_MODE = CFG_DRAM_MODE;
+       *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
+       __asm__ volatile ("sync");
+
        /* normal operation */
-       *(vu_long *)MPC5XXX_SDRAM_CTRL = CFG_DRAM_CONTROL;
-       /* write default TAP delay */
-       *(vu_long *)MPC5XXX_CDM_PORCFG = CFG_DRAM_TAP_DEL << 24;
+       *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
+       __asm__ volatile ("sync");
+}
+#endif
+
+/*
+ * ATTENTION: Although partially referenced initdram does NOT make real use
+ *            use of CFG_SDRAM_BASE. The code does not work if CFG_SDRAM_BASE
+ *            is something else than 0x00000000.
+ */
+
+#if defined(CONFIG_MPC5200)
+long int initdram (int board_type)
+{
+       ulong dramsize = 0;
+       ulong dramsize2 = 0;
+#ifndef CFG_RAMBOOT
+       ulong test1, test2;
+
+       /* setup SDRAM chip selects */
+       *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e;/* 2G at 0x0 */
+       *(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000;/* disabled */
+       __asm__ volatile ("sync");
+
+       /* setup config registers */
+       *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+       *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+       __asm__ volatile ("sync");
+
+#if SDRAM_DDR
+       /* set tap delay */
+       *(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
+       __asm__ volatile ("sync");
+#endif
+
+       /* find RAM size using SDRAM CS0 only */
+       sdram_start(0);
+       test1 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
+       sdram_start(1);
+       test2 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
+       if (test1 > test2) {
+               sdram_start(0);
+               dramsize = test1;
+       } else {
+               dramsize = test2;
+       }
+
+       /* memory smaller than 1MB is impossible */
+       if (dramsize < (1 << 20)) {
+               dramsize = 0;
+       }
+
+       /* set SDRAM CS0 size according to the amount of RAM found */
+       if (dramsize > 0) {
+               *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
+       } else {
+               *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
+       }
+
+       /* let SDRAM CS1 start right after CS0 */
+       *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
+
+       /* find RAM size using SDRAM CS1 only */
+       sdram_start(0);
+       test1 = get_ram_size((ulong *)(CFG_SDRAM_BASE + dramsize), 0x80000000);
+       sdram_start(1);
+       test2 = get_ram_size((ulong *)(CFG_SDRAM_BASE + dramsize), 0x80000000);
+       if (test1 > test2) {
+               sdram_start(0);
+               dramsize2 = test1;
+       } else {
+               dramsize2 = test2;
+       }
+
+       /* memory smaller than 1MB is impossible */
+       if (dramsize2 < (1 << 20)) {
+               dramsize2 = 0;
+       }
+
+       /* set SDRAM CS1 size according to the amount of RAM found */
+       if (dramsize2 > 0) {
+               *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize
+                       | (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
+       } else {
+               *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
+       }
+
+#else /* CFG_RAMBOOT */
+
+       /* retrieve size of memory connected to SDRAM CS0 */
+       dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
+       if (dramsize >= 0x13) {
+               dramsize = (1 << (dramsize - 0x13)) << 20;
+       } else {
+               dramsize = 0;
+       }
+
+       /* retrieve size of memory connected to SDRAM CS1 */
+       dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF;
+       if (dramsize2 >= 0x13) {
+               dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
+       } else {
+               dramsize2 = 0;
+       }
 
 #endif /* CFG_RAMBOOT */
 
-       dramsize = ((1 << (*(vu_long *)MPC5XXX_SDRAM_CS0CFG - 0x13)) << 20) +
-               ((1 << (*(vu_long *)MPC5XXX_SDRAM_CS1CFG - 0x13)) << 20);
+       return dramsize + dramsize2;
+}
+
+#elif defined(CONFIG_MGT5100)
+
+long int initdram (int board_type)
+{
+       ulong dramsize = 0;
+#ifndef CFG_RAMBOOT
+       ulong test1, test2;
+
+       /* setup and enable SDRAM chip selects */
+       *(vu_long *)MPC5XXX_SDRAM_START = 0x00000000;
+       *(vu_long *)MPC5XXX_SDRAM_STOP = 0x0000ffff;/* 2G */
+       *(vu_long *)MPC5XXX_ADDECR |= (1 << 22); /* Enable SDRAM */
+       __asm__ volatile ("sync");
+
+       /* setup config registers */
+       *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+       *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+
+       /* address select register */
+       *(vu_long *)MPC5XXX_SDRAM_XLBSEL = SDRAM_ADDRSEL;
+       __asm__ volatile ("sync");
+
+       /* find RAM size */
+       sdram_start(0);
+       test1 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
+       sdram_start(1);
+       test2 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
+       if (test1 > test2) {
+               sdram_start(0);
+               dramsize = test1;
+       } else {
+               dramsize = test2;
+       }
+
+       /* set SDRAM end address according to size */
+       *(vu_long *)MPC5XXX_SDRAM_STOP = ((dramsize - 1) >> 15);
+
+#else /* CFG_RAMBOOT */
+
+       /* Retrieve amount of SDRAM available */
+       dramsize = ((*(vu_long *)MPC5XXX_SDRAM_STOP + 1) << 15);
+
+#endif /* CFG_RAMBOOT */
 
-       /* return total ram size */
        return dramsize;
 }
 
-/*****************************************************************************
- * print board identification
- *****************************************************************************/
+#else
+#error Neither CONFIG_MPC5200 or CONFIG_MGT5100 defined
+#endif
+
 int checkboard (void)
 {
        puts ("Board: CANMB\n");

diff --git a/doc/README.ocotea-PIBS-to-U-Boot b/doc/README.ocotea-PIBS-to-U-Boot
index 6b276c5f8c5da5995c9d96ea3d0b14c53cea71bd..0044aa0f91b87dd762bee808526b7fe00c52d1c4 100644 (file)
--- a/doc/README.ocotea-PIBS-to-U-Boot
+++ b/doc/README.ocotea-PIBS-to-U-Boot
@@ -77,14 +77,14 @@ U-Boot 1.1.3 (Apr  5 2005 - 22:59:57)
 
 IBM PowerPC 440 GX Rev. C
 Board: IBM 440GX Evaluation Board
-        VCO: 1066 MHz
-        CPU: 533 MHz
-        PLB: 152 MHz
-        OPB: 76 MHz
-        EPB: 76 MHz
+       VCO: 1066 MHz
+       CPU: 533 MHz
+       PLB: 152 MHz
+       OPB: 76 MHz
+       EPB: 76 MHz
 I2C:   ready
 DRAM:  256 MB
-FLASH:  5 MB
+FLASH: 5 MB
 PCI:   Bus Dev VenId DevId Class Int
 In:    serial
 Out:   serial

diff --git a/drivers/netconsole.c b/drivers/netconsole.c
index 6c27c08f2aa5f7dc08e5d5996790109bad3439e5..9cf6cd6339951cbe7b1f91b73a061bb5c4c57653 100644 (file)
--- a/drivers/netconsole.c
+++ b/drivers/netconsole.c
@@ -153,11 +153,12 @@ int nc_start (void)
        nc_port = 6666;         /* default port */
 
        if (getenv ("ncip")) {
+               char *p;
+
                nc_ip = getenv_IPaddr ("ncip");
                if (!nc_ip)
                        return -1;      /* ncip is 0.0.0.0 */
-               char *p = strchr (getenv ("ncip"), ':');
-               if (p)
+               if ((p = strchr (getenv ("ncip"), ':')) != NULL)
                        nc_port = simple_strtoul (p + 1, NULL, 10);
        } else
                nc_ip = ~0;             /* ncip is not set */
@@ -188,13 +189,13 @@ void nc_putc (char c)
 
 void nc_puts (const char *s)
 {
+       int len;
+
        if (output_recursion)
                return;
        output_recursion = 1;
 
-       int len = strlen (s);
-
-       if (len > 512)
+       if ((len = strlen (s)) > 512)
                len = 512;
 
        nc_send_packet (s, len);
@@ -204,6 +205,8 @@ void nc_puts (const char *s)
 
 int nc_getc (void)
 {
+       uchar c;
+
        input_recursion = 1;
 
        net_timeout = 0;        /* no timeout */
@@ -212,8 +215,8 @@ int nc_getc (void)
 
        input_recursion = 0;
 
-       uchar c = input_buffer[input_offset];
-       input_offset++;
+       c = input_buffer[input_offset++];
+
        if (input_offset >= sizeof input_buffer)
                input_offset -= sizeof input_buffer;
        input_size--;

diff --git a/include/configs/canmb.h b/include/configs/canmb.h
index 0bbf41cbc2bdf0cbef22fe3ba4ea9190e9736e38..a8bea02e56e70099834578797be072b8ce09630c 100644 (file)
--- a/include/configs/canmb.h
+++ b/include/configs/canmb.h
@@ -128,18 +128,6 @@
 #define CFG_FLASH_CFI
 #define CFG_FLASH_EMPTY_INFO
 
-/*
- * DRAM configuration
- */
-#define        CFG_DRAM_DDR            0
-#define CFG_DRAM_EMODE         0
-#define CFG_DRAM_MODE          0x00CD
-#define CFG_DRAM_CONTROL       0x514F0000
-#define CFG_DRAM_CONFIG1       0xD2333A00
-#define CFG_DRAM_CONFIG2       0x8AD70004
-#define        CFG_DRAM_TAP_DEL        0x08
-#define CFG_DRAM_RAM_SIZE      0x19
-
 /*
  * Environment settings
  */