Add support for treating unknown PHYs as generic PHYs.

When bringing up u-boot on new boards, PHY support sometimes gets
neglected.  Most PHYs don't really need any special support,
though.  By adding a generic entry that always matches if nothing
else does, we can provide support for "unsupported" PHYs for the
tsec.

The generic PHY driver supports most PHYs, including gigabit.

Signed-off-by: David Updegraff <dave@cray.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

diff --git a/drivers/tsec.c b/drivers/tsec.c
index ed35f227c1b0f3840547d90e6fcedaea21361fd4..25566a73387752285916f186029081e9e3a9532b 100644 (file)
--- a/drivers/tsec.c
+++ b/drivers/tsec.c
@@ -385,6 +385,76 @@ uint mii_parse_sr(uint mii_reg, struct tsec_private * priv)
        return 0;
 }
 
+/* Generic function which updates the speed and duplex.  If
+ * autonegotiation is enabled, it uses the AND of the link
+ * partner's advertised capabilities and our advertised
+ * capabilities.  If autonegotiation is disabled, we use the
+ * appropriate bits in the control register.
+ *
+ * Stolen from Linux's mii.c and phy_device.c
+ */
+uint mii_parse_link(uint mii_reg, struct tsec_private *priv)
+{
+       /* We're using autonegotiation */
+       if (mii_reg & PHY_BMSR_AUTN_ABLE) {
+               uint lpa = 0;
+               uint gblpa = 0;
+
+               /* Check for gigabit capability */
+               if (mii_reg & PHY_BMSR_EXT) {
+                       /* We want a list of states supported by
+                        * both PHYs in the link
+                        */
+                       gblpa = read_phy_reg(priv, PHY_1000BTSR);
+                       gblpa &= read_phy_reg(priv, PHY_1000BTCR) << 2;
+               }
+
+               /* Set the baseline so we only have to set them
+                * if they're different
+                */
+               priv->speed = 10;
+               priv->duplexity = 0;
+
+               /* Check the gigabit fields */
+               if (gblpa & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) {
+                       priv->speed = 1000;
+
+                       if (gblpa & PHY_1000BTSR_1000FD)
+                               priv->duplexity = 1;
+
+                       /* We're done! */
+                       return 0;
+               }
+
+               lpa = read_phy_reg(priv, PHY_ANAR);
+               lpa &= read_phy_reg(priv, PHY_ANLPAR);
+
+               if (lpa & (PHY_ANLPAR_TXFD | PHY_ANLPAR_TX)) {
+                       priv->speed = 100;
+
+                       if (lpa & PHY_ANLPAR_TXFD)
+                               priv->duplexity = 1;
+
+               } else if (lpa & PHY_ANLPAR_10FD)
+                       priv->duplexity = 1;
+       } else {
+               uint bmcr = read_phy_reg(priv, PHY_BMCR);
+
+               priv->speed = 10;
+               priv->duplexity = 0;
+
+               if (bmcr & PHY_BMCR_DPLX)
+                       priv->duplexity = 1;
+
+               if (bmcr & PHY_BMCR_1000_MBPS)
+                       priv->speed = 1000;
+               else if (bmcr & PHY_BMCR_100_MBPS)
+                       priv->speed = 100;
+       }
+
+       return 0;
+}
+
 /*
  * Parse the BCM54xx status register for speed and duplex information.
  * The linux sungem_phy has this information, but in a table format.
@@ -722,6 +792,7 @@ static void startup_tsec(struct eth_device *dev)
        /* Start up the PHY */
        if(priv->phyinfo)
                phy_run_commands(priv, priv->phyinfo->startup);
+
        adjust_link(dev);
 
        /* Enable Transmit and Receive */
@@ -1092,6 +1163,27 @@ struct phy_info phy_info_dm9161 = {
                           {miim_end,}
                           },
 };
+/* a generic flavor.  */
+struct phy_info phy_info_generic =  {
+       0,
+       "Unknown/Generic PHY",
+       32,
+       (struct phy_cmd[]) { /* config */
+               {PHY_BMCR, PHY_BMCR_RESET, NULL},
+               {PHY_BMCR, PHY_BMCR_AUTON|PHY_BMCR_RST_NEG, NULL},
+               {miim_end,}
+       },
+       (struct phy_cmd[]) { /* startup */
+               {PHY_BMSR, miim_read, NULL},
+               {PHY_BMSR, miim_read, &mii_parse_sr},
+               {PHY_BMSR, miim_read, &mii_parse_link},
+               {miim_end,}
+       },
+       (struct phy_cmd[]) { /* shutdown */
+               {miim_end,}
+       }
+};
+
 
 uint mii_parse_lxt971_sr2(uint mii_reg, struct tsec_private *priv)
 {
@@ -1207,6 +1299,7 @@ struct phy_info *phy_info[] = {
        &phy_info_lxt971,
        &phy_info_VSC8244,
        &phy_info_dp83865,
+       &phy_info_generic,
        NULL
 };