armada-388-clearfog.dtb \
armada-388-gp.dtb \
armada-xp-gp.dtb \
- armada-xp-maxbcm.dtb
+ armada-xp-maxbcm.dtb \
+ armada-xp-synology-ds414.dtb
dtb-$(CONFIG_ARCH_UNIPHIER) += \
uniphier-ph1-ld4-ref.dtb \
--- /dev/null
+/*
+ * Device Tree file for Synology DS414
+ *
+ * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the old 0xd0000000).
+ * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot
+ * bootloaders provided by Marvell. It is used in recent versions of
+ * DSM software provided by Synology. Nonetheless, some earlier boards
+ * were delivered with an older version of u-boot that left internal
+ * registers mapped at 0xd0000000. If you have such a device you will
+ * not be able to directly boot a kernel based on this Device Tree. In
+ * that case, the preferred solution is to update your bootloader (e.g.
+ * by upgrading to latest version of DSM, or building a new one and
+ * installing it from u-boot prompt) or adjust the Devive Tree
+ * (s/0xf1000000/0xd0000000/ in 'ranges' below).
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-xp-mv78230.dtsi"
+
+/ {
+ model = "Synology DS414";
+ compatible = "synology,ds414", "marvell,armadaxp-mv78230",
+ "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x40000000>; /* 1GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+
+ pcie-controller {
+ status = "okay";
+
+ /*
+ * Connected to Marvell 88SX7042 SATA-II controller
+ * handling the four disks.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ /*
+ * Connected to EtronTech EJ168A XHCI controller
+ * providing the two rear USB 3.0 ports.
+ */
+ pcie@5,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+
+ /* RTC is provided by Seiko S-35390A below */
+ rtc@10300 {
+ status = "disabled";
+ };
+
+ spi0: spi@10600 {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+
+ spi-flash@0 {
+ u-boot,dm-pre-reloc;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q064";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+
+ /*
+ * Warning!
+ *
+ * Synology u-boot uses its compiled-in environment
+ * and it seems Synology did not care to change u-boot
+ * default configuration in order to allow saving a
+ * modified environment at a sensible location. So,
+ * if you do a 'saveenv' under u-boot, your modified
+ * environment will be saved at 1MB after the start
+ * of the flash, i.e. in the middle of the uImage.
+ * For that reason, it is strongly advised not to
+ * change the default environment, unless you know
+ * what you are doing.
+ */
+ partition@00000000 { /* u-boot */
+ label = "RedBoot";
+ reg = <0x00000000 0x000d0000>; /* 832KB */
+ };
+
+ partition@000c0000 { /* uImage */
+ label = "zImage";
+ reg = <0x000d0000 0x002d0000>; /* 2880KB */
+ };
+
+ partition@003a0000 { /* uInitramfs */
+ label = "rd.gz";
+ reg = <0x003a0000 0x00430000>; /* 4250KB */
+ };
+
+ partition@007d0000 { /* MAC address and serial number */
+ label = "vendor";
+ reg = <0x007d0000 0x00010000>; /* 64KB */
+ };
+
+ partition@007e0000 {
+ label = "RedBoot config";
+ reg = <0x007e0000 0x00010000>; /* 64KB */
+ };
+
+ partition@007f0000 {
+ label = "FIS directory";
+ reg = <0x007f0000 0x00010000>; /* 64KB */
+ };
+ };
+ };
+
+ i2c@11000 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ s35390a: s35390a@30 {
+ compatible = "sii,s35390a";
+ reg = <0x30>;
+ };
+ };
+
+ /* Connected to a header on device's PCB. This
+ * provides the main console for the device.
+ *
+ * Warning: the device may not boot with a 3.3V
+ * USB-serial converter connected when the power
+ * button is pressed. The converter needs to be
+ * connected a few seconds after pressing the
+ * power button. This is possibly due to UART0_TXD
+ * pin being sampled at reset (bit 0 of SAR).
+ */
+ serial@12000 {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+ };
+
+ /* Connected to a Microchip PIC16F883 for power control */
+ serial@12100 {
+ status = "okay";
+ };
+
+ poweroff@12100 {
+ compatible = "synology,power-off";
+ reg = <0x12100 0x100>;
+ clocks = <&coreclk 0>;
+ };
+
+ /* Front USB 2.0 port */
+ usb@50000 {
+ status = "okay";
+ };
+
+ mdio {
+ phy0: ethernet-phy@0 { /* Marvell 88E1512 */
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 { /* Marvell 88E1512 */
+ reg = <1>;
+ };
+ };
+
+ ethernet@70000 {
+ status = "okay";
+ pinctrl-0 = <&ge0_rgmii_pins>;
+ pinctrl-names = "default";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+
+ ethernet@74000 {
+ pinctrl-0 = <&ge1_rgmii_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin
+ &sata3_pwr_pin &sata4_pwr_pin>;
+ pinctrl-names = "default";
+
+ sata1_regulator: sata1-regulator {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "SATA1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <2000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ sata2_regulator: sata2-regulator {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA2 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <4000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ sata3_regulator: sata3-regulator {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "SATA3 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <6000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+ };
+
+ sata4_regulator: sata4-regulator {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "SATA4 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <8000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&pinctrl {
+ sata1_pwr_pin: sata1-pwr-pin {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+
+ sata2_pwr_pin: sata2-pwr-pin {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ sata3_pwr_pin: sata3-pwr-pin {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ sata4_pwr_pin: sata4-pwr-pin {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+
+ sata1_pres_pin: sata1-pres-pin {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+
+ sata2_pres_pin: sata2-pres-pin {
+ marvell,pins = "mpp35";
+ marvell,function = "gpio";
+ };
+
+ sata3_pres_pin: sata3-pres-pin {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+
+ sata4_pres_pin: sata4-pres-pin {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+
+ syno_id_bit0_pin: syno-id-bit0-pin {
+ marvell,pins = "mpp26";
+ marvell,function = "gpio";
+ };
+
+ syno_id_bit1_pin: syno-id-bit1-pin {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ syno_id_bit2_pin: syno-id-bit2-pin {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ fan1_alarm_pin: fan1-alarm-pin {
+ marvell,pins = "mpp33";
+ marvell,function = "gpio";
+ };
+
+ fan2_alarm_pin: fan2-alarm-pin {
+ marvell,pins = "mpp32";
+ marvell,function = "gpio";
+ };
+};
bool "Support db-mv784mp-gp"
select MV78460
+config TARGET_DS414
+ bool "Support Synology DS414"
+ select MV78230
+
config TARGET_MAXBCM
bool "Support maxbcm"
select MV78460
default "clearfog" if TARGET_CLEARFOG
default "db-88f6820-gp" if TARGET_DB_88F6820_GP
default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP
+ default "ds414" if TARGET_DS414
default "maxbcm" if TARGET_MAXBCM
config SYS_CONFIG_NAME
default "clearfog" if TARGET_CLEARFOG
default "db-88f6820-gp" if TARGET_DB_88F6820_GP
default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP
+ default "ds414" if TARGET_DS414
default "maxbcm" if TARGET_MAXBCM
config SYS_VENDOR
default "Marvell" if TARGET_DB_MV784MP_GP
default "Marvell" if TARGET_DB_88F6820_GP
default "solidrun" if TARGET_CLEARFOG
+ default "Synology" if TARGET_DS414
config SYS_SOC
default "mvebu"
#define DB_784MP_GP_ID (RD_78460_SERVER_REV2_ID + 1)
#define RD_78460_CUSTOMER_ID (DB_784MP_GP_ID + 1)
#define MV_MAX_BOARD_ID (RD_78460_CUSTOMER_ID + 1)
-#define INVALID_BAORD_ID 0xFFFFFFFF
+#define INVALID_BOARD_ID 0xFFFFFFFF
/* Sample at Reset */
#define MPP_SAMPLE_AT_RESET(id) (0x18230 + (id * 4))
--- /dev/null
+#
+# Copyright (C) 2015 Phil Sutter <phil@nwl.cc>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := ds414.o
--- /dev/null
+/*
+ *
+ * Copyright (C) 2015 Phil Sutter <phil@nwl.cc>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <linux/mbus.h>
+
+#include "../drivers/ddr/marvell/axp/ddr3_hw_training.h"
+#include "../arch/arm/mach-mvebu/serdes/axp/high_speed_env_spec.h"
+#include "../arch/arm/mach-mvebu/serdes/axp/board_env_spec.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* GPP and MPP settings as found in mvBoardEnvSpec.c of Synology's U-Boot */
+
+#define DS414_GPP_OUT_VAL_LOW (BIT(25) | BIT(30))
+#define DS414_GPP_OUT_VAL_MID (BIT(10) | BIT(15))
+#define DS414_GPP_OUT_VAL_HIGH (0)
+
+#define DS414_GPP_OUT_POL_LOW (0)
+#define DS414_GPP_OUT_POL_MID (0)
+#define DS414_GPP_OUT_POL_HIGH (0)
+
+#define DS414_GPP_OUT_ENA_LOW (~(BIT(25) | BIT(30)))
+#define DS414_GPP_OUT_ENA_MID (~(BIT(10) | BIT(12) | \
+ BIT(13) | BIT(14) | BIT(15)))
+#define DS414_GPP_OUT_ENA_HIGH (~0)
+
+static const u32 ds414_mpp_control[] = {
+ 0x11111111,
+ 0x22221111,
+ 0x22222222,
+ 0x00000000,
+ 0x11110000,
+ 0x00004000,
+ 0x00000000,
+ 0x00000000,
+ 0x00000000
+};
+
+/* DDR3 static MC configuration */
+
+/* 1G_v1 (4x2Gbits) adapted by DS414 */
+MV_DRAM_MC_INIT syno_ddr3_b0_667_1g_v1[MV_MAX_DDR3_STATIC_SIZE] = {
+ {0x00001400, 0x73014A28}, /*DDR SDRAM Configuration Register */
+ {0x00001404, 0x30000800}, /*Dunit Control Low Register */
+ {0x00001408, 0x44148887}, /*DDR SDRAM Timing (Low) Register */
+ {0x0000140C, 0x3AD83FEA}, /*DDR SDRAM Timing (High) Register */
+
+ {0x00001410, 0x14000000}, /*DDR SDRAM Address Control Register */
+
+ {0x00001414, 0x00000000}, /*DDR SDRAM Open Pages Control Register */
+ {0x00001418, 0x00000e00}, /*DDR SDRAM Operation Register */
+ {0x00001420, 0x00000004}, /*DDR SDRAM Extended Mode Register */
+ {0x00001424, 0x0000F3FF}, /*Dunit Control High Register */
+ {0x00001428, 0x000F8830}, /*Dunit Control High Register */
+ {0x0000142C, 0x054C36F4}, /*Dunit Control High Register */
+ {0x0000147C, 0x0000C671},
+
+ {0x000014a0, 0x00000001},
+ {0x000014a8, 0x00000100}, /*2:1 */
+ {0x00020220, 0x00000006},
+
+ {0x00001494, 0x00010000}, /*DDR SDRAM ODT Control (Low) Register */
+ {0x00001498, 0x00000000}, /*DDR SDRAM ODT Control (High) Register */
+ {0x0000149C, 0x00000001}, /*DDR Dunit ODT Control Register */
+
+ {0x000014C0, 0x192424C9}, /* DRAM address and Control Driving Strenght */
+ {0x000014C4, 0x0AAA24C9}, /* DRAM Data and DQS Driving Strenght */
+
+ {0x000200e8, 0x3FFF0E01}, /* DO NOT Modify - Open Mbus Window - 2G - Mbus is required for the training sequence*/
+ {0x00020184, 0x3FFFFFE0}, /* DO NOT Modify - Close fast path Window to - 2G */
+
+ {0x0001504, 0x3FFFFFE1}, /* CS0 Size */
+ {0x000150C, 0x00000000}, /* CS1 Size */
+ {0x0001514, 0x00000000}, /* CS2 Size */
+ {0x000151C, 0x00000000}, /* CS3 Size */
+
+ {0x00001538, 0x00000009}, /*Read Data Sample Delays Register */
+ {0x0000153C, 0x00000009}, /*Read Data Ready Delay Register */
+
+ {0x000015D0, 0x00000650}, /*MR0 */
+ {0x000015D4, 0x00000044}, /*MR1 */
+ {0x000015D8, 0x00000010}, /*MR2 */
+ {0x000015DC, 0x00000000}, /*MR3 */
+
+ {0x000015E4, 0x00203c18}, /*ZQC Configuration Register */
+ {0x000015EC, 0xF800A225}, /*DDR PHY */
+
+ {0x0, 0x0}
+};
+
+MV_DRAM_MODES ds414_ddr_modes[MV_DDR3_MODES_NUMBER] = {
+ {"ds414_1333-667", 0x3, 0x5, 0x0, A0, syno_ddr3_b0_667_1g_v1, NULL},
+};
+
+extern MV_SERDES_CHANGE_M_PHY serdes_change_m_phy[];
+
+MV_BIN_SERDES_CFG ds414_serdes_cfg[] = {
+ { MV_PEX_ROOT_COMPLEX, 0x02011111, 0x00000000,
+ { PEX_BUS_MODE_X4, PEX_BUS_MODE_X1, PEX_BUS_DISABLED,
+ PEX_BUS_DISABLED },
+ 0x0040, serdes_change_m_phy
+ }
+};
+
+MV_DRAM_MODES *ddr3_get_static_ddr_mode(void)
+{
+ return &ds414_ddr_modes[0];
+}
+
+MV_BIN_SERDES_CFG *board_serdes_cfg_get(u8 pex_mode)
+{
+ return &ds414_serdes_cfg[0];
+}
+
+u8 board_sat_r_get(u8 dev_num, u8 reg)
+{
+ return (0x1 << 1 | 1);
+}
+
+int board_early_init_f(void)
+{
+ int i;
+
+ /* Set GPP Out value */
+ reg_write(GPP_DATA_OUT_REG(0), DS414_GPP_OUT_VAL_LOW);
+ reg_write(GPP_DATA_OUT_REG(1), DS414_GPP_OUT_VAL_MID);
+ reg_write(GPP_DATA_OUT_REG(2), DS414_GPP_OUT_VAL_HIGH);
+
+ /* set GPP polarity */
+ reg_write(GPP_DATA_IN_POL_REG(0), DS414_GPP_OUT_POL_LOW);
+ reg_write(GPP_DATA_IN_POL_REG(1), DS414_GPP_OUT_POL_MID);
+ reg_write(GPP_DATA_IN_POL_REG(2), DS414_GPP_OUT_POL_HIGH);
+
+ /* Set GPP Out Enable */
+ reg_write(GPP_DATA_OUT_EN_REG(0), DS414_GPP_OUT_ENA_LOW);
+ reg_write(GPP_DATA_OUT_EN_REG(1), DS414_GPP_OUT_ENA_MID);
+ reg_write(GPP_DATA_OUT_EN_REG(2), DS414_GPP_OUT_ENA_HIGH);
+
+ for (i = 0; i < ARRAY_SIZE(ds414_mpp_control); i++)
+ reg_write(MPP_CONTROL_REG(i), ds414_mpp_control[i]);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ u32 pwr_mng_ctrl_reg;
+
+ /* Adress of boot parameters */
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+ /* Gate unused clocks
+ *
+ * Note: Disabling unused PCIe lanes will hang PCI bus scan.
+ * Once this is resolved, bits 10-12, 26 and 27 can be
+ * unset here as well.
+ */
+ pwr_mng_ctrl_reg = reg_read(POWER_MNG_CTRL_REG);
+ pwr_mng_ctrl_reg &= ~(BIT(0)); /* Audio */
+ pwr_mng_ctrl_reg &= ~(BIT(1) | BIT(2)); /* GE3, GE2 */
+ pwr_mng_ctrl_reg &= ~(BIT(14) | BIT(15)); /* SATA0 link and core */
+ pwr_mng_ctrl_reg &= ~(BIT(16)); /* LCD */
+ pwr_mng_ctrl_reg &= ~(BIT(17)); /* SDIO */
+ pwr_mng_ctrl_reg &= ~(BIT(19) | BIT(20)); /* USB1 and USB2 */
+ pwr_mng_ctrl_reg &= ~(BIT(29) | BIT(30)); /* SATA1 link and core */
+ reg_write(POWER_MNG_CTRL_REG, pwr_mng_ctrl_reg);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: DS414\n");
+
+ return 0;
+}
--- /dev/null
+#
+# Copyright (C) 2014 Stefan Roese <sr@denx.de>
+#
+
+# Armada XP uses version 1 image format
+VERSION 1
+
+# Boot Media configurations
+BOOT_FROM spi
+
+# Binary Header (bin_hdr) with DDR3 training code
+BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_DS414=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-xp-synology-ds414"
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_BASE=0xd0012000
+CONFIG_DEBUG_UART_CLOCK=250000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
--- /dev/null
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _CONFIG_SYNOLOGY_DS414_H
+#define _CONFIG_SYNOLOGY_DS414_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+/*
+ * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
+ * for DDR ECC byte filling in the SPL before loading the main
+ * U-Boot into it.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x00800000
+#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_TFTPPUT
+#define CONFIG_CMD_TIME
+#define CONFIG_CMD_USB
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MVTWSI
+#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
+#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_SYS_I2C_SPEED 100000
+
+/* SPI NOR flash default params, used by sf commands */
+#define CONFIG_SF_DEFAULT_SPEED 1000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
+
+/* Environment in SPI NOR flash */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET 0x7E0000 /* RedBoot config partition in DTS */
+#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
+#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */
+
+#define CONFIG_PHY_MARVELL /* there is a marvell phy */
+#define CONFIG_PHY_ADDR { 0x1, 0x0 }
+#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII
+
+#define CONFIG_SYS_ALT_MEMTEST
+
+/* PCIe support */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PCI_ENUM
+#define CONFIG_PCI_MVEBU
+#define CONFIG_PCI_SCAN_SHOW
+#endif
+
+/* USB/EHCI/XHCI configuration */
+
+#define CONFIG_DM_USB
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
+/* FIXME: broken XHCI support
+ * Below defines should enable support for the two rear USB3 ports. Sadly, this
+ * does not work because:
+ * - xhci-pci seems to not support DM_USB, so with that enabled it is not
+ * found.
+ * - USB init fails, controller does not respond in time */
+#if 0
+#undef CONFIG_DM_USB
+#define CONFIG_USB_XHCI
+#define CONFIG_USB_XHCI_PCI
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
+#endif
+
+#if !defined(CONFIG_USB_XHCI)
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MARVELL
+#define CONFIG_EHCI_IS_TDI
+#endif
+
+/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_SYS_MVFS
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/*
+ * Memory layout while starting into the bin_hdr via the
+ * BootROM:
+ *
+ * 0x4000.4000 - 0x4003.4000 headers space (192KiB)
+ * 0x4000.4030 bin_hdr start address
+ * 0x4003.4000 - 0x4004.7c00 BootROM memory allocations (15KiB)
+ * 0x4007.fffc BootROM stack top
+ *
+ * The address space between 0x4007.fffc and 0x400f.fff is not locked in
+ * L2 cache thus cannot be used.
+ */
+
+/* SPL */
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x40004030
+#define CONFIG_SPL_MAX_SIZE ((128 << 10) - 0x4030)
+
+#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))
+#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
+
+#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
+#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+
+/* SPL related SPI defines */
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_BUS 0
+#define CONFIG_SPL_SPI_CS 0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000
+
+/* DS414 bus width is 32bits */
+#define CONFIG_DDR_32BIT
+
+/* Use random ethernet address if not configured */
+#define CONFIG_LIB_RAND
+#define CONFIG_NET_RANDOM_ETHADDR
+
+/* Default Environment */
+#define CONFIG_BOOTCOMMAND "sf read ${loadaddr} 0xd0000 0x700000; bootm"
+#define CONFIG_BOOTARGS "console=ttyS0,115200"
+#define CONFIG_LOADADDR 0x80000
+#undef CONFIG_PREBOOT /* override preboot for USB and SPI flash init */
+#define CONFIG_PREBOOT "usb start; sf probe"
+
+#endif /* _CONFIG_SYNOLOGY_DS414_H */
projects / u-boot.git / commitdiff