/*
* Xilinx SPI driver
*
- * supports 8 bit SPI transfers only, with or w/o FIFO
+ * Supports 8 bit SPI transfers only, with or w/o FIFO
*
- * based on bfin_spi.c, by way of altera_spi.c
- * Copyright (c) 2005-2008 Analog Devices Inc.
- * Copyright (c) 2010 Thomas Chou <thomas@wytron.com.tw>
- * Copyright (c) 2010 Graeme Smecher <graeme.smecher@mail.mcgill.ca>
+ * Based on bfin_spi.c, by way of altera_spi.c
* Copyright (c) 2012 Stephan Linz <linz@li-pro.net>
+ * Copyright (c) 2010 Graeme Smecher <graeme.smecher@mail.mcgill.ca>
+ * Copyright (c) 2010 Thomas Chou <thomas@wytron.com.tw>
+ * Copyright (c) 2005-2008 Analog Devices Inc.
*
* SPDX-License-Identifier: GPL-2.0+
- *
- * [0]: http://www.xilinx.com/support/documentation
- *
- * [S]: [0]/ip_documentation/xps_spi.pdf
- * [0]/ip_documentation/axi_spi_ds742.pdf
*/
+
#include <config.h>
#include <common.h>
#include <malloc.h>
#include <spi.h>
/*
- * Xilinx SPI Register Definition
+ * [0]: http://www.xilinx.com/support/documentation
*
+ * Xilinx SPI Register Definitions
* [1]: [0]/ip_documentation/xps_spi.pdf
* page 8, Register Descriptions
* [2]: [0]/ip_documentation/axi_spi_ds742.pdf
* page 7, Register Overview Table
*/
-struct xilinx_spi_reg {
- u32 __space0__[7];
- u32 dgier; /* Device Global Interrupt Enable Register (DGIER) */
- u32 ipisr; /* IP Interrupt Status Register (IPISR) */
- u32 __space1__;
- u32 ipier; /* IP Interrupt Enable Register (IPIER) */
- u32 __space2__[5];
- u32 srr; /* Softare Reset Register (SRR) */
- u32 __space3__[7];
- u32 spicr; /* SPI Control Register (SPICR) */
- u32 spisr; /* SPI Status Register (SPISR) */
- u32 spidtr; /* SPI Data Transmit Register (SPIDTR) */
- u32 spidrr; /* SPI Data Receive Register (SPIDRR) */
- u32 spissr; /* SPI Slave Select Register (SPISSR) */
- u32 spitfor; /* SPI Transmit FIFO Occupancy Register (SPITFOR) */
- u32 spirfor; /* SPI Receive FIFO Occupancy Register (SPIRFOR) */
-};
-
-/* Device Global Interrupt Enable Register (dgier), [1] p15, [2] p15 */
-#define DGIER_GIE (1 << 31)
-
-/* IP Interrupt Status Register (ipisr), [1] p15, [2] p15 */
-#define IPISR_DRR_NOT_EMPTY (1 << 8)
-#define IPISR_SLAVE_SELECT (1 << 7)
-#define IPISR_TXF_HALF_EMPTY (1 << 6)
-#define IPISR_DRR_OVERRUN (1 << 5)
-#define IPISR_DRR_FULL (1 << 4)
-#define IPISR_DTR_UNDERRUN (1 << 3)
-#define IPISR_DTR_EMPTY (1 << 2)
-#define IPISR_SLAVE_MODF (1 << 1)
-#define IPISR_MODF (1 << 0)
-
-/* IP Interrupt Enable Register (ipier), [1] p17, [2] p18 */
-#define IPIER_DRR_NOT_EMPTY (1 << 8)
-#define IPIER_SLAVE_SELECT (1 << 7)
-#define IPIER_TXF_HALF_EMPTY (1 << 6)
-#define IPIER_DRR_OVERRUN (1 << 5)
-#define IPIER_DRR_FULL (1 << 4)
-#define IPIER_DTR_UNDERRUN (1 << 3)
-#define IPIER_DTR_EMPTY (1 << 2)
-#define IPIER_SLAVE_MODF (1 << 1)
-#define IPIER_MODF (1 << 0)
-
-/* Softare Reset Register (srr), [1] p9, [2] p8 */
-#define SRR_RESET_CODE 0x0000000A
/* SPI Control Register (spicr), [1] p9, [2] p8 */
#define SPICR_LSB_FIRST (1 << 9)
#define SPISSR_ACT(cs) ~SPISSR_MASK(cs)
#define SPISSR_OFF ~0UL
-/* SPI Transmit FIFO Occupancy Register (spitfor), [1] p13, [2] p14 */
-#define SPITFOR_OCYVAL_POS 0
-#define SPITFOR_OCYVAL_MASK (0xf << SPITFOR_OCYVAL_POS)
-
-/* SPI Receive FIFO Occupancy Register (spirfor), [1] p14, [2] p14 */
-#define SPIRFOR_OCYVAL_POS 0
-#define SPIRFOR_OCYVAL_MASK (0xf << SPIRFOR_OCYVAL_POS)
-
/* SPI Software Reset Register (ssr) */
#define SPISSR_RESET_VALUE 0x0a
+#define XILSPI_MAX_XFER_BITS 8
+#define XILSPI_SPICR_DFLT_ON (SPICR_MANUAL_SS | SPICR_MASTER_MODE | \
+ SPICR_SPE)
+#define XILSPI_SPICR_DFLT_OFF (SPICR_MASTER_INHIBIT | SPICR_MANUAL_SS)
+
+#ifndef CONFIG_XILINX_SPI_IDLE_VAL
+#define CONFIG_XILINX_SPI_IDLE_VAL 0xff
+#endif
+
+#ifndef CONFIG_SYS_XILINX_SPI_LIST
+#define CONFIG_SYS_XILINX_SPI_LIST { CONFIG_SYS_SPI_BASE }
+#endif
+
+/* xilinx spi register set */
+struct xilinx_spi_reg {
+ u32 __space0__[7];
+ u32 dgier; /* Device Global Interrupt Enable Register (DGIER) */
+ u32 ipisr; /* IP Interrupt Status Register (IPISR) */
+ u32 __space1__;
+ u32 ipier; /* IP Interrupt Enable Register (IPIER) */
+ u32 __space2__[5];
+ u32 srr; /* Softare Reset Register (SRR) */
+ u32 __space3__[7];
+ u32 spicr; /* SPI Control Register (SPICR) */
+ u32 spisr; /* SPI Status Register (SPISR) */
+ u32 spidtr; /* SPI Data Transmit Register (SPIDTR) */
+ u32 spidrr; /* SPI Data Receive Register (SPIDRR) */
+ u32 spissr; /* SPI Slave Select Register (SPISSR) */
+ u32 spitfor; /* SPI Transmit FIFO Occupancy Register (SPITFOR) */
+ u32 spirfor; /* SPI Receive FIFO Occupancy Register (SPIRFOR) */
+};
+
+/* xilinx spi slave */
struct xilinx_spi_slave {
struct spi_slave slave;
struct xilinx_spi_reg *regs;
};
static inline struct xilinx_spi_slave *to_xilinx_spi_slave(
- struct spi_slave *slave)
+ struct spi_slave *slave)
{
return container_of(slave, struct xilinx_spi_slave, slave);
}
-#ifndef CONFIG_SYS_XILINX_SPI_LIST
-#define CONFIG_SYS_XILINX_SPI_LIST { CONFIG_SYS_SPI_BASE }
-#endif
-
-#ifndef CONFIG_XILINX_SPI_IDLE_VAL
-#define CONFIG_XILINX_SPI_IDLE_VAL 0xff
-#endif
-
-#define XILSPI_SPICR_DFLT_ON (SPICR_MANUAL_SS | \
- SPICR_MASTER_MODE | \
- SPICR_SPE)
-
-#define XILSPI_SPICR_DFLT_OFF (SPICR_MASTER_INHIBIT | \
- SPICR_MANUAL_SS)
-
-#define XILSPI_MAX_XFER_BITS 8
-
static unsigned long xilinx_spi_base_list[] = CONFIG_SYS_XILINX_SPI_LIST;
-
-__attribute__((weak))
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
return bus < ARRAY_SIZE(xilinx_spi_base_list) && cs < 32;
}
-__attribute__((weak))
void spi_cs_activate(struct spi_slave *slave)
{
struct xilinx_spi_slave *xilspi = to_xilinx_spi_slave(slave);
writel(SPISSR_ACT(slave->cs), &xilspi->regs->spissr);
}
-__attribute__((weak))
void spi_cs_deactivate(struct spi_slave *slave)
{
struct xilinx_spi_slave *xilspi = to_xilinx_spi_slave(slave);
/* do nothing */
}
-void spi_set_speed(struct spi_slave *slave, uint hz)
-{
- /* xilinx spi core does not support programmable speed */
-}
-
struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
unsigned int max_hz, unsigned int mode)
{
struct xilinx_spi_slave *xilspi;
if (!spi_cs_is_valid(bus, cs)) {
- printf("XILSPI error: %s: unsupported bus %d / cs %d\n",
- __func__, bus, cs);
+ printf("XILSPI error: unsupported bus %d / cs %d\n", bus, cs);
return NULL;
}
xilspi = spi_alloc_slave(struct xilinx_spi_slave, bus, cs);
if (!xilspi) {
- printf("XILSPI error: %s: malloc of SPI structure failed\n",
- __func__);
+ printf("XILSPI error: malloc of SPI structure failed\n");
return NULL;
}
xilspi->regs = (struct xilinx_spi_reg *)xilinx_spi_base_list[bus];
xilspi->freq = max_hz;
xilspi->mode = mode;
- debug("%s: bus:%i cs:%i base:%p mode:%x max_hz:%d\n", __func__,
- bus, cs, xilspi->regs, xilspi->mode, xilspi->freq);
+ debug("spi_setup_slave: bus:%i cs:%i base:%p mode:%x max_hz:%d\n",
+ bus, cs, xilspi->regs, xilspi->mode, xilspi->freq);
writel(SPISSR_RESET_VALUE, &xilspi->regs->srr);
struct xilinx_spi_slave *xilspi = to_xilinx_spi_slave(slave);
u32 spicr;
- debug("%s: bus:%i cs:%i\n", __func__, slave->bus, slave->cs);
+ debug("spi_claim_bus: bus:%i cs:%i\n", slave->bus, slave->cs);
writel(SPISSR_OFF, &xilspi->regs->spissr);
spicr = XILSPI_SPICR_DFLT_ON;
{
struct xilinx_spi_slave *xilspi = to_xilinx_spi_slave(slave);
- debug("%s: bus:%i cs:%i\n", __func__, slave->bus, slave->cs);
+ debug("spi_release_bus: bus:%i cs:%i\n", slave->bus, slave->cs);
writel(SPISSR_OFF, &xilspi->regs->spissr);
writel(XILSPI_SPICR_DFLT_OFF, &xilspi->regs->spicr);
}
unsigned rxecount = 17; /* max. 16 elements in FIFO, leftover 1 */
unsigned global_timeout;
- debug("%s: bus:%i cs:%i bitlen:%i bytes:%i flags:%lx\n", __func__,
- slave->bus, slave->cs, bitlen, bytes, flags);
+ debug("spi_xfer: bus:%i cs:%i bitlen:%i bytes:%i flags:%lx\n",
+ slave->bus, slave->cs, bitlen, bytes, flags);
+
if (bitlen == 0)
goto done;
if (bitlen % XILSPI_MAX_XFER_BITS) {
- printf("XILSPI warning: %s: Not a multiple of %d bits\n",
- __func__, XILSPI_MAX_XFER_BITS);
+ printf("XILSPI warning: Not a multiple of %d bits\n",
+ XILSPI_MAX_XFER_BITS);
flags |= SPI_XFER_END;
goto done;
}
}
if (!rxecount) {
- printf("XILSPI error: %s: Rx buffer not empty\n", __func__);
+ printf("XILSPI error: Rx buffer not empty\n");
return -1;
}
unsigned timeout = global_timeout;
/* get Tx element from data out buffer and count up */
unsigned char d = txp ? *txp++ : CONFIG_XILINX_SPI_IDLE_VAL;
- debug("%s: tx:%x ", __func__, d);
+ debug("spi_xfer: tx:%x ", d);
/* write out and wait for processing (receive data) */
writel(d & SPIDTR_8BIT_MASK, &xilspi->regs->spidtr);
}
if (!timeout) {
- printf("XILSPI error: %s: Xfer timeout\n", __func__);
+ printf("XILSPI error: Xfer timeout\n");
return -1;
}
d = readl(&xilspi->regs->spidrr) & SPIDRR_8BIT_MASK;
if (rxp)
*rxp++ = d;
- debug("rx:%x\n", d);
+ debug("spi_xfer: rx:%x\n", d);
}
done:
projects / u-boot.git / commitdiff