--- /dev/null
+/*
+ * Microsemi PHY drivers
+ *
+ * SPDX-License-Identifier: The MIT License (MIT)
+ *
+ * Copyright (c) 2016 Microsemi Corporation
+ *
+ * Author: John Haechten
+ *
+ */
+
+#include <miiphy.h>
+#include <bitfield.h>
+
+/* Microsemi PHY ID's */
+#define PHY_ID_VSC8530 0x00070560
+#define PHY_ID_VSC8531 0x00070570
+#define PHY_ID_VSC8540 0x00070760
+#define PHY_ID_VSC8541 0x00070770
+
+/* Microsemi VSC85xx PHY Register Pages */
+#define MSCC_EXT_PAGE_ACCESS 31 /* Page Access Register */
+#define MSCC_PHY_PAGE_STD 0x0000 /* Standard registers */
+#define MSCC_PHY_PAGE_EXT1 0x0001 /* Extended registers - page 1 */
+#define MSCC_PHY_PAGE_EXT2 0x0002 /* Extended registers - page 2 */
+#define MSCC_PHY_PAGE_EXT3 0x0003 /* Extended registers - page 3 */
+#define MSCC_PHY_PAGE_EXT4 0x0004 /* Extended registers - page 4 */
+#define MSCC_PHY_PAGE_GPIO 0x0010 /* GPIO registers */
+#define MSCC_PHY_PAGE_TEST 0x2A30 /* TEST Page registers */
+#define MSCC_PHY_PAGE_TR 0x52B5 /* Token Ring Page registers */
+
+/* Std Page Register 28 - PHY AUX Control/Status */
+#define MIIM_AUX_CNTRL_STAT_REG 28
+#define MIIM_AUX_CNTRL_STAT_ACTIPHY_TO (0x0004)
+#define MIIM_AUX_CNTRL_STAT_F_DUPLEX (0x0020)
+#define MIIM_AUX_CNTRL_STAT_SPEED_MASK (0x0018)
+#define MIIM_AUX_CNTRL_STAT_SPEED_POS (3)
+#define MIIM_AUX_CNTRL_STAT_SPEED_10M (0x0)
+#define MIIM_AUX_CNTRL_STAT_SPEED_100M (0x1)
+#define MIIM_AUX_CNTRL_STAT_SPEED_1000M (0x2)
+
+/* Std Page Register 23 - Extended PHY CTRL_1 */
+#define MSCC_PHY_EXT_PHY_CNTL_1_REG 23
+#define MAC_IF_SELECTION_MASK (0x1800)
+#define MAC_IF_SELECTION_GMII (0)
+#define MAC_IF_SELECTION_RMII (1)
+#define MAC_IF_SELECTION_RGMII (2)
+#define MAC_IF_SELECTION_POS (11)
+#define MAC_IF_SELECTION_WIDTH (2)
+
+/* Extended Page 2 Register 20E2 */
+#define MSCC_PHY_RGMII_CNTL_REG 20
+#define VSC_FAST_LINK_FAIL2_ENA_MASK (0x8000)
+#define RX_CLK_OUT_MASK (0x0800)
+#define RX_CLK_OUT_POS (11)
+#define RX_CLK_OUT_WIDTH (1)
+#define RX_CLK_OUT_NORMAL (0)
+#define RX_CLK_OUT_DISABLE (1)
+#define RGMII_RX_CLK_DELAY_POS (4)
+#define RGMII_RX_CLK_DELAY_WIDTH (3)
+#define RGMII_RX_CLK_DELAY_MASK (0x0070)
+#define RGMII_TX_CLK_DELAY_POS (0)
+#define RGMII_TX_CLK_DELAY_WIDTH (3)
+#define RGMII_TX_CLK_DELAY_MASK (0x0007)
+
+/* Extended Page 2 Register 27E2 */
+#define MSCC_PHY_WOL_MAC_CONTROL 27
+#define EDGE_RATE_CNTL_POS (5)
+#define EDGE_RATE_CNTL_WIDTH (3)
+#define EDGE_RATE_CNTL_MASK (0x00E0)
+#define RMII_CLK_OUT_ENABLE_POS (4)
+#define RMII_CLK_OUT_ENABLE_WIDTH (1)
+#define RMII_CLK_OUT_ENABLE_MASK (0x10)
+
+/* Token Ring Page 0x52B5 Registers */
+#define MSCC_PHY_REG_TR_ADDR_16 16
+#define MSCC_PHY_REG_TR_DATA_17 17
+#define MSCC_PHY_REG_TR_DATA_18 18
+
+/* Token Ring - Read Value in */
+#define MSCC_PHY_TR_16_READ (0xA000)
+/* Token Ring - Write Value out */
+#define MSCC_PHY_TR_16_WRITE (0x8000)
+
+/* Token Ring Registers */
+#define MSCC_PHY_TR_LINKDETCTRL_POS (3)
+#define MSCC_PHY_TR_LINKDETCTRL_WIDTH (2)
+#define MSCC_PHY_TR_LINKDETCTRL_VAL (3)
+#define MSCC_PHY_TR_LINKDETCTRL_MASK (0x0018)
+#define MSCC_PHY_TR_LINKDETCTRL_ADDR (0x07F8)
+
+#define MSCC_PHY_TR_VGATHRESH100_POS (0)
+#define MSCC_PHY_TR_VGATHRESH100_WIDTH (7)
+#define MSCC_PHY_TR_VGATHRESH100_VAL (0x0018)
+#define MSCC_PHY_TR_VGATHRESH100_MASK (0x007f)
+#define MSCC_PHY_TR_VGATHRESH100_ADDR (0x0FA4)
+
+#define MSCC_PHY_TR_VGAGAIN10_U_POS (0)
+#define MSCC_PHY_TR_VGAGAIN10_U_WIDTH (1)
+#define MSCC_PHY_TR_VGAGAIN10_U_MASK (0x0001)
+#define MSCC_PHY_TR_VGAGAIN10_U_VAL (0)
+
+#define MSCC_PHY_TR_VGAGAIN10_L_POS (12)
+#define MSCC_PHY_TR_VGAGAIN10_L_WIDTH (4)
+#define MSCC_PHY_TR_VGAGAIN10_L_MASK (0xf000)
+#define MSCC_PHY_TR_VGAGAIN10_L_VAL (0x0001)
+#define MSCC_PHY_TR_VGAGAIN10_ADDR (0x0F92)
+
+/* General Timeout Values */
+#define MSCC_PHY_RESET_TIMEOUT (100)
+#define MSCC_PHY_MICRO_TIMEOUT (500)
+
+/* RGMII/GMII Clock Delay (Skew) Options */ enum vsc_phy_rgmii_skew {
+ VSC_PHY_RGMII_DELAY_200_PS,
+ VSC_PHY_RGMII_DELAY_800_PS,
+ VSC_PHY_RGMII_DELAY_1100_PS,
+ VSC_PHY_RGMII_DELAY_1700_PS,
+ VSC_PHY_RGMII_DELAY_2000_PS,
+ VSC_PHY_RGMII_DELAY_2300_PS,
+ VSC_PHY_RGMII_DELAY_2600_PS,
+ VSC_PHY_RGMII_DELAY_3400_PS,
+};
+
+/* MAC i/f Clock Edge Rage Control (Slew), See Reg27E2 */ enum
+vsc_phy_clk_slew {
+ VSC_PHY_CLK_SLEW_RATE_0,
+ VSC_PHY_CLK_SLEW_RATE_1,
+ VSC_PHY_CLK_SLEW_RATE_2,
+ VSC_PHY_CLK_SLEW_RATE_3,
+ VSC_PHY_CLK_SLEW_RATE_4,
+ VSC_PHY_CLK_SLEW_RATE_5,
+ VSC_PHY_CLK_SLEW_RATE_6,
+ VSC_PHY_CLK_SLEW_RATE_7,
+};
+
+
+static int mscc_vsc8531_vsc8541_init_scripts(struct phy_device *phydev)
+{
+ u16 reg_val;
+
+ /* Set to Access Token Ring Registers */
+ phy_write(phydev, MDIO_DEVAD_NONE,
+ MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_TR);
+
+ /* Update LinkDetectCtrl default to optimized values */
+ /* Determined during Silicon Validation Testing */
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_ADDR_16,
+ (MSCC_PHY_TR_LINKDETCTRL_ADDR | MSCC_PHY_TR_16_READ));
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_DATA_17);
+ reg_val = bitfield_replace(reg_val, MSCC_PHY_TR_LINKDETCTRL_POS,
+ MSCC_PHY_TR_LINKDETCTRL_WIDTH,
+ MSCC_PHY_TR_LINKDETCTRL_VAL);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_DATA_17, reg_val);
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_ADDR_16,
+ (MSCC_PHY_TR_LINKDETCTRL_ADDR | MSCC_PHY_TR_16_WRITE));
+
+ /* Update VgaThresh100 defaults to optimized values */
+ /* Determined during Silicon Validation Testing */
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_ADDR_16,
+ (MSCC_PHY_TR_VGATHRESH100_ADDR | MSCC_PHY_TR_16_READ));
+
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_DATA_18);
+ reg_val = bitfield_replace(reg_val, MSCC_PHY_TR_VGATHRESH100_POS,
+ MSCC_PHY_TR_VGATHRESH100_WIDTH,
+ MSCC_PHY_TR_VGATHRESH100_VAL);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_DATA_18, reg_val);
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_ADDR_16,
+ (MSCC_PHY_TR_VGATHRESH100_ADDR | MSCC_PHY_TR_16_WRITE));
+
+ /* Update VgaGain10 defaults to optimized values */
+ /* Determined during Silicon Validation Testing */
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_ADDR_16,
+ (MSCC_PHY_TR_VGAGAIN10_ADDR | MSCC_PHY_TR_16_READ));
+
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_DATA_18);
+ reg_val = bitfield_replace(reg_val, MSCC_PHY_TR_VGAGAIN10_U_POS,
+ MSCC_PHY_TR_VGAGAIN10_U_WIDTH,
+ MSCC_PHY_TR_VGAGAIN10_U_VAL);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_DATA_18, reg_val);
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_DATA_17);
+ reg_val = bitfield_replace(reg_val, MSCC_PHY_TR_VGAGAIN10_L_POS,
+ MSCC_PHY_TR_VGAGAIN10_L_WIDTH,
+ MSCC_PHY_TR_VGAGAIN10_L_VAL);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_DATA_17, reg_val);
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_REG_TR_ADDR_16,
+ (MSCC_PHY_TR_VGAGAIN10_ADDR | MSCC_PHY_TR_16_WRITE));
+
+ /* Set back to Access Standard Page Registers */
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_STD);
+
+ return 0;
+}
+
+static int mscc_parse_status(struct phy_device *phydev)
+{
+ u16 speed;
+ u16 mii_reg;
+
+ mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_AUX_CNTRL_STAT_REG);
+
+ if (mii_reg & MIIM_AUX_CNTRL_STAT_F_DUPLEX)
+ phydev->duplex = DUPLEX_FULL;
+ else
+ phydev->duplex = DUPLEX_HALF;
+
+ speed = mii_reg & MIIM_AUX_CNTRL_STAT_SPEED_MASK;
+ speed = speed >> MIIM_AUX_CNTRL_STAT_SPEED_POS;
+
+ switch (speed) {
+ case MIIM_AUX_CNTRL_STAT_SPEED_1000M:
+ phydev->speed = SPEED_1000;
+ break;
+ case MIIM_AUX_CNTRL_STAT_SPEED_100M:
+ phydev->speed = SPEED_100;
+ break;
+ case MIIM_AUX_CNTRL_STAT_SPEED_10M:
+ phydev->speed = SPEED_10;
+ break;
+ default:
+ phydev->speed = SPEED_10;
+ break;
+ }
+
+ return 0;
+}
+
+static int mscc_startup(struct phy_device *phydev)
+{
+ int retval;
+
+ retval = genphy_update_link(phydev);
+
+ if (retval)
+ return retval;
+
+ return mscc_parse_status(phydev);
+}
+
+static int mscc_phy_soft_reset(struct phy_device *phydev)
+{
+ int retval = 0;
+ u16 timeout = MSCC_PHY_RESET_TIMEOUT;
+ u16 reg_val = 0;
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_STD);
+
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+ phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, (reg_val | BMCR_RESET));
+
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+
+ while ((reg_val & BMCR_RESET) && (timeout > 0)) {
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR);
+ timeout--;
+ udelay(1000); /* 1 ms */
+ }
+
+ if (timeout == 0) {
+ printf("MSCC PHY Soft_Reset Error: mac i/f = 0x%x\n",
+ phydev->interface);
+ retval = -ETIME;
+ }
+
+ return retval;
+}
+
+static int vsc8531_vsc8541_mac_config(struct phy_device *phydev)
+{
+ u16 reg_val = 0;
+ u16 mac_if = 0;
+ u16 rx_clk_out = 0;
+
+ /* For VSC8530/31 the only MAC modes are RMII/RGMII. */
+ /* For VSC8540/41 the only MAC modes are (G)MII and RMII/RGMII. */
+ /* Setup MAC Configuration */
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_MII:
+ case PHY_INTERFACE_MODE_GMII:
+ /* Set Reg23.12:11=0 */
+ mac_if = MAC_IF_SELECTION_GMII;
+ /* Set Reg20E2.11=1 */
+ rx_clk_out = RX_CLK_OUT_DISABLE;
+ break;
+
+ case PHY_INTERFACE_MODE_RMII:
+ /* Set Reg23.12:11=1 */
+ mac_if = MAC_IF_SELECTION_RMII;
+ /* Set Reg20E2.11=0 */
+ rx_clk_out = RX_CLK_OUT_NORMAL;
+ break;
+
+ case PHY_INTERFACE_MODE_RGMII:
+ /* Set Reg23.12:11=2 */
+ mac_if = MAC_IF_SELECTION_RGMII;
+ /* Set Reg20E2.11=0 */
+ rx_clk_out = RX_CLK_OUT_NORMAL;
+ break;
+
+ default:
+ printf("MSCC PHY - INVALID MAC i/f Config: mac i/f = 0x%x\n",
+ phydev->interface);
+ return -EINVAL;
+ }
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_STD);
+
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE,
+ MSCC_PHY_EXT_PHY_CNTL_1_REG);
+ /* Set MAC i/f bits Reg23.12:11 */
+ reg_val = bitfield_replace(reg_val, MAC_IF_SELECTION_POS,
+ MAC_IF_SELECTION_WIDTH, mac_if);
+ /* Update Reg23.12:11 */
+ phy_write(phydev, MDIO_DEVAD_NONE,
+ MSCC_PHY_EXT_PHY_CNTL_1_REG, reg_val);
+ /* Setup ExtPg_2 Register Access */
+ phy_write(phydev, MDIO_DEVAD_NONE,
+ MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXT2);
+ /* Read Reg20E2 */
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE,
+ MSCC_PHY_RGMII_CNTL_REG);
+ reg_val = bitfield_replace(reg_val, RX_CLK_OUT_POS,
+ RX_CLK_OUT_WIDTH, rx_clk_out);
+ /* Update Reg20E2.11 */
+ phy_write(phydev, MDIO_DEVAD_NONE,
+ MSCC_PHY_RGMII_CNTL_REG, reg_val);
+ /* Before leaving - Change back to Std Page Register Access */
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_STD);
+
+ return 0;
+}
+
+static int vsc8531_config(struct phy_device *phydev)
+{
+ int retval = -EINVAL;
+ u16 reg_val;
+ u16 rmii_clk_out;
+ enum vsc_phy_rgmii_skew rx_clk_skew = VSC_PHY_RGMII_DELAY_1700_PS;
+ enum vsc_phy_rgmii_skew tx_clk_skew = VSC_PHY_RGMII_DELAY_800_PS;
+ enum vsc_phy_clk_slew edge_rate = VSC_PHY_CLK_SLEW_RATE_4;
+
+ /* For VSC8530/31 and VSC8540/41 the init scripts are the same */
+ mscc_vsc8531_vsc8541_init_scripts(phydev);
+
+ /* For VSC8530/31 the only MAC modes are RMII/RGMII. */
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_RMII:
+ case PHY_INTERFACE_MODE_RGMII:
+ retval = vsc8531_vsc8541_mac_config(phydev);
+ if (retval != 0)
+ return retval;
+
+ retval = mscc_phy_soft_reset(phydev);
+ if (retval != 0)
+ return retval;
+ break;
+ default:
+ printf("PHY 8530/31 MAC i/f Config Error: mac i/f = 0x%x\n",
+ phydev->interface);
+ return -EINVAL;
+ }
+ /* Default RMII Clk Output to 0=OFF/1=ON */
+ rmii_clk_out = 0;
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXT2);
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG);
+
+ /* Reg20E2 - Update RGMII RX_Clk Skews. */
+ reg_val = bitfield_replace(reg_val, RGMII_RX_CLK_DELAY_POS,
+ RGMII_RX_CLK_DELAY_WIDTH, rx_clk_skew);
+ /* Reg20E2 - Update RGMII TX_Clk Skews. */
+ reg_val = bitfield_replace(reg_val, RGMII_TX_CLK_DELAY_POS,
+ RGMII_TX_CLK_DELAY_WIDTH, tx_clk_skew);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG, reg_val);
+
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_WOL_MAC_CONTROL);
+ /* Reg27E2 - Update Clk Slew Rate. */
+ reg_val = bitfield_replace(reg_val, EDGE_RATE_CNTL_POS,
+ EDGE_RATE_CNTL_WIDTH, edge_rate);
+ /* Reg27E2 - Update RMII Clk Out. */
+ reg_val = bitfield_replace(reg_val, RMII_CLK_OUT_ENABLE_POS,
+ RMII_CLK_OUT_ENABLE_WIDTH, rmii_clk_out);
+ /* Update Reg27E2 */
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_WOL_MAC_CONTROL, reg_val);
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_STD);
+
+ return genphy_config_aneg(phydev);
+}
+
+static int vsc8541_config(struct phy_device *phydev)
+{
+ int retval = -EINVAL;
+ u16 reg_val;
+ u16 rmii_clk_out;
+ enum vsc_phy_rgmii_skew rx_clk_skew = VSC_PHY_RGMII_DELAY_1700_PS;
+ enum vsc_phy_rgmii_skew tx_clk_skew = VSC_PHY_RGMII_DELAY_800_PS;
+ enum vsc_phy_clk_slew edge_rate = VSC_PHY_CLK_SLEW_RATE_4;
+
+ /* For VSC8530/31 and VSC8540/41 the init scripts are the same */
+ mscc_vsc8531_vsc8541_init_scripts(phydev);
+
+ /* For VSC8540/41 the only MAC modes are (G)MII and RMII/RGMII. */
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_MII:
+ case PHY_INTERFACE_MODE_GMII:
+ case PHY_INTERFACE_MODE_RMII:
+ case PHY_INTERFACE_MODE_RGMII:
+ retval = vsc8531_vsc8541_mac_config(phydev);
+ if (retval != 0)
+ return retval;
+
+ retval = mscc_phy_soft_reset(phydev);
+ if (retval != 0)
+ return retval;
+ break;
+ default:
+ printf("PHY 8541 MAC i/f config Error: mac i/f = 0x%x\n",
+ phydev->interface);
+ return -EINVAL;
+ }
+ /* Default RMII Clk Output to 0=OFF/1=ON */
+ rmii_clk_out = 0;
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_EXT2);
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG);
+ /* Reg20E2 - Update RGMII RX_Clk Skews. */
+ reg_val = bitfield_replace(reg_val, RGMII_RX_CLK_DELAY_POS,
+ RGMII_RX_CLK_DELAY_WIDTH, rx_clk_skew);
+ /* Reg20E2 - Update RGMII TX_Clk Skews. */
+ reg_val = bitfield_replace(reg_val, RGMII_TX_CLK_DELAY_POS,
+ RGMII_TX_CLK_DELAY_WIDTH, tx_clk_skew);
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG, reg_val);
+
+ reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_WOL_MAC_CONTROL);
+ /* Reg27E2 - Update Clk Slew Rate. */
+ reg_val = bitfield_replace(reg_val, EDGE_RATE_CNTL_POS,
+ EDGE_RATE_CNTL_WIDTH, edge_rate);
+ /* Reg27E2 - Update RMII Clk Out. */
+ reg_val = bitfield_replace(reg_val, RMII_CLK_OUT_ENABLE_POS,
+ RMII_CLK_OUT_ENABLE_WIDTH, rmii_clk_out);
+ /* Update Reg27E2 */
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_WOL_MAC_CONTROL, reg_val);
+ phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS,
+ MSCC_PHY_PAGE_STD);
+
+ return genphy_config_aneg(phydev);
+}
+
+static struct phy_driver VSC8530_driver = {
+ .name = "Microsemi VSC8530",
+ .uid = PHY_ID_VSC8530,
+ .mask = 0x000ffff0,
+ .features = PHY_BASIC_FEATURES,
+ .config = &vsc8531_config,
+ .startup = &mscc_startup,
+ .shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver VSC8531_driver = {
+ .name = "Microsemi VSC8531",
+ .uid = PHY_ID_VSC8531,
+ .mask = 0x000ffff0,
+ .features = PHY_GBIT_FEATURES,
+ .config = &vsc8531_config,
+ .startup = &mscc_startup,
+ .shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver VSC8540_driver = {
+ .name = "Microsemi VSC8540",
+ .uid = PHY_ID_VSC8540,
+ .mask = 0x000ffff0,
+ .features = PHY_BASIC_FEATURES,
+ .config = &vsc8541_config,
+ .startup = &mscc_startup,
+ .shutdown = &genphy_shutdown,
+};
+
+static struct phy_driver VSC8541_driver = {
+ .name = "Microsemi VSC8541",
+ .uid = PHY_ID_VSC8541,
+ .mask = 0x000ffff0,
+ .features = PHY_GBIT_FEATURES,
+ .config = &vsc8541_config,
+ .startup = &mscc_startup,
+ .shutdown = &genphy_shutdown,
+};
+
+int phy_mscc_init(void)
+{
+ phy_register(&VSC8530_driver);
+ phy_register(&VSC8531_driver);
+ phy_register(&VSC8540_driver);
+ phy_register(&VSC8541_driver);
+
+ return 0;
+}
projects / u-boot.git / commitdiff