select SSCANF
endchoice
+config SUPPORT_PASSING_ATAGS
+ bool "Support pre-devicetree ATAG-based booting"
+ depends on !ARM64
+ imply SETUP_MEMORY_TAGS
+ help
+ Support for booting older Linux kernels, using ATAGs rather than
+ passing a devicetree. This is option is rarely used, and the
+ semantics are defined at
+ https://www.kernel.org/doc/Documentation/arm/Booting at section 4a.
+
+config SETUP_MEMORY_TAGS
+ bool "Pass memory size information via ATAG"
+ depends on SUPPORT_PASSING_ATAGS
+
+config CMDLINE_TAG
+ bool "Pass Linux kernel cmdline via ATAG"
+ depends on SUPPORT_PASSING_ATAGS
+
+config INITRD_TAG
+ bool "Pass initrd starting point and size via ATAG"
+ depends on SUPPORT_PASSING_ATAGS
+
+config REVISION_TAG
+ bool "Pass system revision via ATAG"
+ depends on SUPPORT_PASSING_ATAGS
+
+config SERIAL_TAG
+ bool "Pass system serial number via ATAG"
+ depends on SUPPORT_PASSING_ATAGS
+
config ARCH_SUPPORT_TFABOOT
bool
return 0;
}
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
int rev = 0;
return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
}
+#endif
/*
* called prior to booting kernel or by 'fdt boardsetup' command
#
# Copyright (C) 2021 Phil Sutter <phil@nwl.cc>
-obj-y += legacy.o
+obj-$(SUPPORT_PASSING_ATAGS) += legacy.o
DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
}
+#endif
/*
* Set CCAT mode
return 0;
}
-u32 get_board_rev(void)
-{
- return 0;
-}
-
void reset_cpu(void)
{
}
return 0;
}
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
return cl_eeprom_get_board_rev(CONFIG_SYS_I2C_EEPROM_BUS);
}
+#endif
static struct mxc_serial_plat cm_fx6_mxc_serial_plat = {
.reg = (struct mxc_uart *)UART4_BASE,
#define REV_AM18X_EVM 0x100
+#ifdef CONFIG_REVISION_TAG
/*
* get_board_rev() - setup to pass kernel board revision information
* Returns:
rev = 1;
return rev;
}
+#endif
int board_early_init_f(void)
{
#define CONFIG_DA850_EVM_MAX_CPU_CLK 456000000
#endif
-/*
- * get_board_rev() - setup to pass kernel board revision information
- * Returns:
- * bit[0-3] Maximum cpu clock rate supported by onboard SoC
- * 0000b - 300 MHz
- * 0001b - 372 MHz
- * 0010b - 408 MHz
- * 0011b - 456 MHz
- */
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int board_early_init_f(void)
{
/*
}
#endif
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int board_init(void)
{
gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
}
#endif
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int board_init(void)
{
gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
return 0;
}
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
u32 rev = get_cpu_rev();
rev |= BOARD_REV_2_0 << BOARD_VER_OFFSET;
return rev;
}
+#endif
#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_DSE_HIGH)
DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
}
+#endif
#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
}
#endif
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
int rev = nxp_board_rev();
return (get_cpu_rev() & ~(0xF << 8)) | rev;
}
+#endif
static int ar8031_phy_fixup(struct phy_device *phydev)
{
env_set("ethaddr", ethaddr);
}
-#ifdef CONFIG_REVISION_TAG
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
static void set_board_rev(void)
{
char info[64] = {0, };
- snprintf(info, ARRAY_SIZE(info), "%02x", get_board_rev());
+ snprintf(info, ARRAY_SIZE(info), "%02x", get_board_revision());
env_set("board_rev", info);
}
#endif
char info[64] = {0, };
snprintf(info, ARRAY_SIZE(info),
- "s5p4418-nanopi2-rev%02x.dtb", get_board_rev());
+ "s5p4418-nanopi2-rev%02x.dtb", get_board_revision());
env_set("dtb_name", info);
}
{
bd_update_env();
-#ifdef CONFIG_REVISION_TAG
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
set_board_rev();
#endif
set_dtb_name();
}
/* To override __weak symbols */
-u32 get_board_rev(void)
+u32 get_board_revision(void)
{
return (base_rev << 8) | pcb_rev;
}
+#ifdef CONFIG_REVISION_TAG
+u32 get_board_rev(void)
+{
+ return get_board_revision();
+}
+#endif
+
const char *get_board_name(void)
{
bd_hwrev_init();
extern void bd_hwrev_init(void);
extern void bd_base_rev_init(void);
-extern u32 get_board_rev(void);
+extern u32 get_board_revision(void);
extern const char *get_board_name(void);
#endif /* __BD_HW_REV_H__ */
return 0;
}
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
return get_cpu_rev() & ~(0xF << 8);
}
+#endif
#ifdef CONFIG_USB_EHCI_MX5
int board_ehci_hcd_init(int port)
DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
}
+#endif
struct fsl_esdhc_cfg esdhc_cfg[1] = {
{MMC_SDHC1_BASE_ADDR}
return 0;
}
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
/* Sold devices are expected to be at least revision F. */
return 6;
}
+#endif
void get_board_serial(struct tag_serialnr *serialnr)
{
return 0;
}
+#ifdef CONFIG_REVISION_TAG
/*
* Routine: get_board_revision
* Description: Return board revision.
{
return simple_strtol(hw_build_ptr, NULL, 16);
}
+#endif
/*
* Routine: setup_board_tags
return 0;
}
-static void get_board_rev(void)
+static void get_board_revision(void)
{
ALLOC_CACHE_ALIGN_BUFFER(struct msg_get_board_rev, msg, 1);
int ret;
hw_watchdog_init();
#endif
- get_board_rev();
+ get_board_revision();
gd->bd->bi_boot_params = 0x100;
{ EXYNOS5_BOARD_ODROID_UNKNOWN, 0, 4095, "unknown" },
};
-static unsigned int odroid_get_rev(void)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(odroid_info); i++) {
- if (odroid_info[i].board_type == gd->board_type)
- return odroid_info[i].board_rev;
- }
-
- return 0;
-}
-
/*
* Read ADC at least twice and check the resuls. If regulator providing voltage
* on to measured point was just turned on, first reads might require time
return false;
}
+#ifdef CONFIG_REVISION_TAG
+static unsigned int odroid_get_rev(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(odroid_info); i++) {
+ if (odroid_info[i].board_type == gd->board_type)
+ return odroid_info[i].board_rev;
+ }
+
+ return 0;
+}
+
/**
* get_board_rev() - return detected board revision.
*
return odroid_get_rev();
}
+#endif
/**
* get_board_type() - returns board type string.
DECLARE_GLOBAL_DATA_PTR;
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int board_init(void)
{
/* Set Initial global variables */
#include <asm/arch/pinmux.h>
#include <usb.h>
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int exynos_init(void)
{
return 0;
board_rev = modelrev << 8;
}
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
return board_rev;
}
+#endif
static inline u32 get_model_rev(void)
{
unsigned int board_rev;
static int init_pmic_lcd(void);
+#ifdef CONFIG_REVISION_TAG
u32 get_board_rev(void)
{
return board_rev;
}
+#endif
int exynos_power_init(void)
{
return 0;
}
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int board_init(void)
{
gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
return 0;
}
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int board_init(void)
{
gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
return 0;
}
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int board_init(void)
{
gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
{
return BOOT_DEVICE_XIP;
}
-
#endif
-u32 get_board_rev(void)
-{
- return 0;
-}
int board_late_init(void)
{
return 0;
}
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int board_init(void)
{
gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
return 0;
}
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int board_init(void)
{
gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
return 0;
}
-u32 get_board_rev(void)
-{
- return 0;
-}
-
int board_late_init(void)
{
return 0;
#endif
#endif
+#ifdef CONFIG_REVISION_TAG
/*
* get_board_rev() - get board revision
*/
{
return 0x20;
}
+#endif
}
#endif /* CONFIG_SPL_OS_BOOT */
+#ifdef CONFIG_REVISION_TAG
/*
* get_board_rev() - get board revision
*/
{
return 0x20;
}
+#endif
#ifdef CONFIG_BOARD_LATE_INIT
int board_late_init(void)
{
-#if defined(CONFIG_REVISION_TAG) && \
- defined(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG)
+#if defined(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG)
char env_str[256];
u32 rev;
- rev = get_board_rev();
+ rev = get_board_revision();
snprintf(env_str, ARRAY_SIZE(env_str), "%.4x", rev);
env_set("board_rev", env_str);
#ifdef CONFIG_BOARD_LATE_INIT
int board_late_init(void)
{
-#if defined(CONFIG_REVISION_TAG) && \
- defined(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG)
+#if defined(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG)
char env_str[256];
u32 rev;
- rev = get_board_rev();
+ rev = get_board_revision();
snprintf(env_str, ARRAY_SIZE(env_str), "%.4x", rev);
env_set("board_rev", env_str);
#endif
static char *tdx_carrier_board_name;
#endif
-#ifdef CONFIG_REVISION_TAG
-u32 get_board_rev(void)
+#if defined(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG)
+u32 get_board_revision(void)
{
/* Check validity */
if (!tdx_hw_tag.ver_major)
#else /* CONFIG_TDX_CFG_BLOCK */
-#ifdef CONFIG_REVISION_TAG
-u32 get_board_rev(void)
+#if defined(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG)
+u32 get_board_revision(void)
{
return 0;
}
#define TDX_USB_VID 0x1B67
int ft_common_board_setup(void *blob, struct bd_info *bd);
+u32 get_board_revision(void);
#if defined(CONFIG_DM_VIDEO)
int show_boot_logo(void);
CONFIG_SYS_DCACHE_OFF=y
CONFIG_ARCH_CPU_INIT=y
CONFIG_ARCH_KIRKWOOD=y
+CONFIG_SUPPORT_PASSING_ATAGS=y
+CONFIG_CMDLINE_TAG=y
+CONFIG_INITRD_TAG=y
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_NR_DRAM_BANKS=2
CONFIG_TARGET_DS109=y
CONFIG_ARM=y
CONFIG_ARCH_CPU_INIT=y
CONFIG_ARCH_MVEBU=y
+CONFIG_SUPPORT_PASSING_ATAGS=y
+CONFIG_CMDLINE_TAG=y
+CONFIG_INITRD_TAG=y
CONFIG_SYS_TEXT_BASE=0x00800000
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
+CONFIG_SUPPORT_PASSING_ATAGS=y
+CONFIG_CMDLINE_TAG=y
+CONFIG_INITRD_TAG=y
+CONFIG_SERIAL_TAG=y
CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-icnova-swac"
CONFIG_SPL=y
CONFIG_MACH_SUN7I=y
CONFIG_SKIP_LOWLEVEL_INIT=y
# CONFIG_SYS_THUMB_BUILD is not set
CONFIG_ARCH_OMAP2PLUS=y
+CONFIG_SUPPORT_PASSING_ATAGS=y
+CONFIG_CMDLINE_TAG=y
+CONFIG_INITRD_TAG=y
+CONFIG_REVISION_TAG=y
CONFIG_SYS_TEXT_BASE=0x80008000
CONFIG_NR_DRAM_BANKS=2
CONFIG_SYS_MALLOC_LEN=0xc0000
CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_ARCH_U8500=y
+CONFIG_SUPPORT_PASSING_ATAGS=y
+# CONFIG_SETUP_MEMORY_TAGS is not set
+CONFIG_INITRD_TAG=y
CONFIG_SYS_TEXT_BASE=0x100000
CONFIG_NR_DRAM_BANKS=2
CONFIG_SYS_MALLOC_LEN=0x0200000
* for your console driver.
*/
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
-
#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
#define MTDPARTS_MTDOOPS "errlog"
#define CONFIG_DOS_PARTITION
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
/* size in bytes reserved for initial data */
* for your console driver.
*/
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
-
#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
#define MTDPARTS_MTDOOPS "errlog"
#define CONFIG_DOS_PARTITION
#include <configs/ti_omap3_common.h>
-#define CONFIG_REVISION_TAG
-
/* Hardware drivers */
/*
#include "imx6_spl.h"
#endif
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_MXC_UART_BASE UART1_BASE
/* MMC Configs */
#include <asm/arch/platform.h>
/* Misc CPU related */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
#define CONFIG_SYS_SDRAM_BASE ASPEED_DRAM_BASE
#endif
/* Misc CPU related */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
#include <asm/hardware.h>
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
#define CONFIG_ATMEL_LEGACY
/*
#define CONFIG_SYS_AT91_MAIN_CLOCK 16367660 /* 16.367 MHz crystal */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
#ifndef CONFIG_SYS_USE_BOOT_NORFLASH
#else
#define CONFIG_SYS_USE_NORFLASH
#define CONFIG_AT91SAM9M10G45EK
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
#define CONFIG_SYS_AT91_MAIN_CLOCK 16000000 /* main clock xtal */
/* Misc CPU related */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
/* LCD */
#define LCD_BPP LCD_COLOR16
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* main clock xtal */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
#define CONFIG_ATMEL_LEGACY
/*
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
/*
* Informational display configuration.
*/
-#define CONFIG_REVISION_TAG
/*
* Command configuration.
#include <asm/arch/imx-regs.h>
#include <linux/sizes.h>
-/* Enable passing of ATAGs */
-#define CONFIG_CMDLINE_TAG
-
/* NAND support */
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_POWER_TPS65217
-/* Support both device trees and ATAGs. */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
/*#define CONFIG_MACH_TYPE 3589*/
#define CONFIG_MACH_TYPE 0xFFFFFFFF /* TODO: check with kernel*/
#define CONFIG_FSL_USDHC
/* Boot */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
#define CONFIG_MACH_TYPE 0xFFFFFFFF
/* misc */
" bootm ${loadaddr} - ${dtbaddr}\0"
#endif /* !CONFIG_SPL_BUILD*/
-/* Support both device trees and ATAGs. */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* SPI Flash */
/* Environment */
#define CONFIG_BOOTCOMMAND "mmc dev 1; run b_default"
-/* Support both device trees and ATAGs. */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* Environment */
#endif /* __CONFIG_BRXRE1_H__ */
#include "imx6_spl.h"
#endif
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_MXC_UART_BASE UART1_BASE
/* MMC Configs */
"fi; " \
"bootm 0xc0000;"
#define CONFIG_TIMESTAMP
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
/*
* Serial Console Configuration
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
*/
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
#define CONFIG_HWCONFIG /* enable hwconfig */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTCOMMAND \
"run envboot; " \
* U-Boot Commands
*/
-/*
- * Boot Linux
- */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-
#define CONFIG_BOOTFILE "uImage"
/*
#include <configs/ti_omap3_common.h>
-#define CONFIG_REVISION_TAG 1
-
/* Hardware drivers */
/* DM9000 */
#define CONFIG_NET_RETRY_COUNT 20
/* Miscellaneous configurable options */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
/* Bootcounter */
#define CONFIG_SYS_BOOTCOUNT_BE
#include "imx6_spl.h"
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_MXC_UART_BASE UART5_BASE
/* I2C Configs */
/* auto boot */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
-
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
/*
/* File systems */
/* Boot command */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
#define CONFIG_BOOTCOMMAND "sf probe 0:0; " \
"sf read 0x22000000 0xc6000 0x294000; " \
"bootm 0x22000000"
#define CONFIG_SYS_CLK_FREQ 24000000
#define COUNTER_FREQUENCY CONFIG_SYS_CLK_FREQ
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_INITRD_TAG
-
/* select serial console configuration */
/* PWM */
#define CONFIG_BOARD_COMMON
-#define CONFIG_REVISION_TAG
-
/* SD/MMC configuration */
#define CONFIG_MMC_DEFAULT_DEV 0
/* This is required to setup the ESDC controller */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_REVISION_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/*
* Hardware drivers
*/
#include "mx6_common.h"
#include <linux/sizes.h>
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
/* SATA Configs */
#ifdef CONFIG_CMD_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 1
/* Miscellaneous */
#define CONFIG_SYS_PBSIZE 256
-#define CONFIG_CMDLINE_TAG
/* Internal RAM Size (RZ/A1=3M, RZ/A1M=5M, RZ/A1H=10M) */
#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_MX27
#define CONFIG_MX27_CLK32 32768 /* OSC32K frequency */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
/*
* Lowlevel configuration
*/
#define CONFIG_SYS_TIMERBASE 0x13000100 /* Timer1 */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-
/*
* There are various dependencies on the core module (CM) fitted
* Users should refer to their CM user guide
"appended one; fi\0" \
""
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */
-
/*
* NAND Flash configuration
*/
#include "imx6_spl.h" /* common IMX6 SPL configuration */
/* Miscellaneous configurable options */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
/* FEC ethernet */
#define CONFIG_ARP_TIMEOUT 200UL
#include <asm/arch/rmobile.h>
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* MEMORY */
#define KZM_SDRAM_BASE (0x40000000)
#define PHYS_SDRAM KZM_SDRAM_BASE
*/
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
#define CONFIG_HWCONFIG /* enable hwconfig */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_SETUP_INITRD_TAG
#define CONFIG_BOOTCOMMAND \
"if mmc rescan; then " \
#define CONFIG_PCI_SCAN_SHOW
#endif
-#define CONFIG_CMDLINE_TAG
-
#define CONFIG_PEN_ADDR_BIG_ENDIAN
#define CONFIG_LAYERSCAPE_NS_ACCESS
#define CONFIG_SMP_PEN_ADDR 0x01ee0200
#define CONFIG_PCI_SCAN_SHOW
#endif
-#define CONFIG_CMDLINE_TAG
-
#define CONFIG_PEN_ADDR_BIG_ENDIAN
#define CONFIG_LAYERSCAPE_NS_ACCESS
#define CONFIG_SMP_PEN_ADDR 0x01ee0200
#define CONFIG_PCI_SCAN_SHOW
#endif
-#define CONFIG_CMDLINE_TAG
-
#define CONFIG_PEN_ADDR_BIG_ENDIAN
#define CONFIG_LAYERSCAPE_NS_ACCESS
#define CONFIG_SMP_PEN_ADDR 0x01ee0200
* Environment
*/
-#define CONFIG_CMDLINE_TAG
-
#include <asm/fsl_secure_boot.h>
#endif /* __LS1043AQDS_H__ */
* Environment
*/
-#define CONFIG_CMDLINE_TAG
-
#undef CONFIG_BOOTCOMMAND
#ifdef CONFIG_TFABOOT
#define IFC_NAND_BOOTCOMMAND "run distro_bootcmd; run nand_bootcmd; " \
#include <asm/arch/imx-regs.h>
-#define CONFIG_REVISION_TAG
#define CONFIG_SYS_FSL_CLK
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
/*
* Boot Linux
*/
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTFILE "boot/fitImage"
#define CONFIG_BOOTCOMMAND "run mmc_mmc"
#define CONFIG_SYS_AT91_MAIN_CLOCK 16000000/* 16.0 MHz crystal */
/* Misc CPU related */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_SERIAL_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
/*
* Hardware drivers
#include <linux/sizes.h>
/* Miscellaneous configurable options */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_CMDLINE_TAG
#define CONFIG_SYS_MAXARGS 8
#define CONFIG_SYS_BOOTM_LEN SZ_64M
#include <linux/sizes.h>
/* Miscellaneous configurable options */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_CMDLINE_TAG
#define CONFIG_SYS_MAXARGS 8
#define CONFIG_SYS_BOOTM_LEN SZ_64M
/* auto boot */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
-
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
/*
4000000, 4500000, 5000000, 5500000, \
6000000 }
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */
-
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
/*
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
115200, 230400, 460800, 921600 }
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */
-
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
/*
#include <asm/arch/imx-regs.h>
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_MACH_TYPE MACH_TYPE_MX51_BABBAGE
/*
* Hardware drivers
#include <asm/arch/imx-regs.h>
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
#define CONFIG_SYS_FSL_CLK
-#define CONFIG_REVISION_TAG
-
#define CONFIG_MXC_UART_BASE UART2_BASE
#define CONFIG_FPGA_COUNT 1
#include <asm/arch/imx-regs.h>
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
#define CONFIG_SYS_FSL_CLK
-#define CONFIG_REVISION_TAG
-
#define CONFIG_MXC_UART_BASE UART1_BASE
/* MMC Configs */
#include <asm/arch/imx-regs.h>
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
#define CONFIG_SYS_FSL_CLK
-#define CONFIG_REVISION_TAG
-
/* USB Configs */
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_SYS_FSL_CLK
-/* ATAGs */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
/* Miscellaneous configurable options */
#define CONFIG_SYS_CBSIZE 512
#define CONFIG_SYS_MAXARGS 32
#define CONFIG_SYS_HZ_CLOCK 1000000 /* Fixed at 1MHz from TSTMR */
-#define CONFIG_INITRD_TAG
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-
/* UART */
#define LPUART_BASE LPUART4_RBASE
#define CONFIG_SYS_HZ_CLOCK 1000000 /* Fixed at 1Mhz from TSTMR */
-#define CONFIG_INITRD_TAG
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-/*#define CONFIG_REVISION_TAG*/
-
/* UART */
#define LPUART_BASE LPUART4_RBASE
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* Boot argument buffer size */
-/* Booting Linux */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-
/*
* Drivers
*/
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#define CONFIG_CMDLINE_TAG /* enable passing kernel command line string */
-#define CONFIG_INITRD_TAG /* enable passing initrd */
-#define CONFIG_REVISION_TAG /* enable passing revision tag*/
-#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */
-
#define CONFIG_UBI_SIZE (512 << 10)
/*
*/
#define CONFIG_MISC_COMMON
-#undef CONFIG_REVISION_TAG
-
#endif /* __CONFIG_H */
/* Set soc_rev, soc_id, board_rev, board_name, fdtfile */
#define CONFIG_ODROID_REV_AIN 9
-#define CONFIG_REVISION_TAG
/*
* Need to override existing one (smdk5420) with odroid so set_board_info will
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB).
*/
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
/* NAND */
#if defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_SYS_FLASH_BASE NAND_BASE
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB).
*/
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
/* NAND */
#if defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_SYS_FLASH_BASE NAND_BASE
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB).
*/
-#define CONFIG_REVISION_TAG 1
-
/* TPS65950 */
#define PBIASLITEVMODE1 (1 << 8)
* order to allow for BCH8 to fit in.
*/
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
/* Hardware drivers */
/* I2C */
* Linux Information
*/
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTCOMMAND \
"run envboot; " \
"run mmcboot; "
#include <linux/sizes.h>
#include <linux/stringify.h>
-/* Enable passing of ATAGs */
-#define CONFIG_CMDLINE_TAG
-
/* NAND support */
#define CONFIG_SYS_NAND_ONFI_DETECTION
AT91_WDT_MR_WDDIS | \
AT91_WDT_MR_WDD(0xfff))
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
/*
* Hardware drivers
*/
AT91_WDT_MR_WDDIS | \
AT91_WDT_MR_WDD(0xfff))
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
#define CONFIG_USER_LOWLEVEL_INIT 1
/*
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
#include <asm/arch/rmobile.h>
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
#ifdef CONFIG_SPL
#define CONFIG_SPL_TARGET "spl/u-boot-spl.srec"
#endif
/* boot option */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* Generic Interrupt Controller Definitions */
#define GICD_BASE 0xF1010000
#define GICC_BASE 0xF1020000
/* Shell */
-/* ATAGs support for bootm/bootz */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_INITRD_TAG
-
/* Environment */
#define ENV_DEVICE_SETTINGS \
"stdin=serial,usbkbd\0" \
/* Text Base */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_INITRD_TAG
-
/* MMC */
#define SDHCI_MAX_HOSTS 4
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 24000000 /* 24 MHz crystal */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID 0 /* ignored in arm */
#define CONFIG_MACH_TYPE CONFIG_SIEMENS_MACH_TYPE
#endif
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* commands to include */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432MHz crystal */
/* misc settings */
-#define CONFIG_CMDLINE_TAG /* pass commandline to Kernel */
-#define CONFIG_SETUP_MEMORY_TAGS /* pass memory defs to kernel */
-#define CONFIG_INITRD_TAG /* pass initrd param to kernel */
/* We set the max number of command args high to avoid HUSH bugs. */
#define CONFIG_SYS_MAXARGS 32
/* Text Base */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_INITRD_TAG
-
/*
* select serial console configuration
*/
#undef CONFIG_BOARD_COMMON
#undef CONFIG_USB_GADGET_DWC2_OTG_PHY
-#undef CONFIG_REVISION_TAG
/* High Level Configuration Options */
#define CONFIG_EXYNOS4210 1 /* which is a EXYNOS4210 SoC */
/* CPU */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1
#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* 64MB */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
/* CPU */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS6
"bootfile=/boot/extlinux/extlinux.conf\0" \
"bootargs=console=ttyO2,115200 vram=5M,0x9FA00000 omapfb.vram=0:5M\0"
-/*
- * ATAGs
- */
-
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-#define CONFIG_SERIAL_TAG
-
/*
* Boot
*/
"setenv altbootcmd 'setenv bootnum b && saveenv && boot;' && " \
"saveenv && saveenv && boot;"
-#define CONFIG_CMDLINE_TAG
#define CONFIG_SYS_BOOTM_LEN (64 << 20)
/* Environment settings */
#define CONFIG_SYS_L2_PL310
#define CONFIG_SYS_PL310_BASE 0xa0412000
-/* Generate initrd atag for downstream kernel (others are copied in stemmy.c) */
-#define CONFIG_INITRD_TAG
-
/* Linux does not boot if FDT / initrd is loaded to end of RAM */
#define BOOT_ENV \
"fdt_high=0x6000000\0" \
/* Extra Commands */
-#define CONFIG_SETUP_MEMORY_TAGS
-
#define CONFIG_SYS_GBL_DATA_SIZE 1024 /* Global data structures */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - \
CONFIG_SYS_MALLOC_LEN - \
#define CONFIG_SYS_HZ_CLOCK 1000000 /* Timer is clocked at 1MHz */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_SYS_CBSIZE 1024
#define CONFIG_BOOTCOMMAND \
#define CONFIG_SYS_HZ_CLOCK 1000000 /* Timer is clocked at 1MHz */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_SYS_CBSIZE 1024
#define BOOT_TARGET_DEVICES(func) \
#define CONFIG_SYS_HZ_CLOCK 1000000 /* Timer is clocked at 1MHz */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_SYS_CBSIZE 1024
#define BOOT_TARGET_DEVICES(func) \
#define CONFIG_SYS_HZ_CLOCK 1000000 /* Timer is clocked at 1MHz */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_SYS_CBSIZE 1024
#define BOOT_TARGET_DEVICES(func) \
#define CONFIG_SYS_HZ_CLOCK 1000000
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_SYS_MAXARGS 16
#define BOOT_TARGET_DEVICES(func) \
#define CONFIG_SYS_HZ_CLOCK 1000000
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_SYS_MAXARGS 16
#define BOOT_TARGET_DEVICES(func) \
#define CONFIG_SYS_HZ_CLOCK 1000000
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
#define CONFIG_SYS_MAXARGS 16
#define BOOT_TARGET_DEVICES(func) \
*/
#define CONFIG_SYS_CBSIZE SZ_1K
-/* ATAGs */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/*
* For booting Linux, use the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
#define CONFIG_SYS_64BIT_LBA
#endif
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_INITRD_TAG
-#define CONFIG_SERIAL_TAG
-
#ifdef CONFIG_NAND_SUNXI
#define CONFIG_SYS_NAND_MAX_ECCPOS 1664
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
/*
* DDR related
*/
#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */
/* Misc CPU related */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
#define CONFIG_TEGRA_SLINK_CTRLS 6
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
-/* Tag support */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
#include "tegra-common-post.h"
#endif /* __CONFIG_H */
#define CONFIG_SYS_TIMER_COUNTER NV_PA_TMRUS_BASE
#endif
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-
/* Environment */
/*
#define CONFIG_MACH_TYPE MACH_TYPE_TI8148EVM
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG /* for ramdisk support */
-
/* commands to include */
#define CONFIG_EXTRA_ENV_SETTINGS \
#ifndef __CONFIG_TI_ARMV7_COMMON_H__
#define __CONFIG_TI_ARMV7_COMMON_H__
-/* Support both device trees and ATAGs. */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/*
* We setup defaults based on constraints from the Linux kernel, which should
* also be safe elsewhere. We have the default load at 32MB into DDR (for
4000000, 4500000, 5000000, 5500000, \
6000000 }
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */
-
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
/*
#define CONFIG_MACH_TYPE MACH_TYPE_USB_A9263
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/*
* Hardware drivers
*/
/* Board info register */
#define SYS_ID V2M_SYSREGS
-#define CONFIG_REVISION_TAG 1
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_SYS_L2CACHE_OFF 1
-#define CONFIG_INITRD_TAG 1
#define SCTL_BASE V2M_SYSCTL
#define VEXPRESS_FLASHPROG_FLVPPEN (1 << 0)
#define CONFIG_MACH_TYPE 4146
-/* Enable passing of ATAGs */
-#define CONFIG_CMDLINE_TAG
-
/* NAND support */
#define CONFIG_SYS_NAND_ONFI_DETECTION
/*
* Boot Linux
*/
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
#define CONFIG_BOOTFILE "uImage"
"fatls usb 0; fatload usb 0 0x81000000 zmx25-init.bin;" \
"bootm 0x81000000; bootelf 0x81000000\0"
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
/*
* Hardware drivers
*/
projects / u-boot.git / commitdiff