-// SPDX-License-Identifier: GPL-2.0
/*
* DTS File for HiSilicon Poplar Development Board
*
* Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
+ *
+ * Released under the GPLv2 only.
+ * SPDX-License-Identifier: GPL-2.0
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "hi3798cv200.dtsi"
+#include "poplar-pinctrl.dtsi"
/ {
model = "HiSilicon Poplar Development Board";
default-state = "off";
};
};
+
+ reg_pcie: regulator-pcie {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3_PCIE0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio6 7 0>;
+ enable-active-high;
+ };
+};
+
+&ehci {
+ status = "okay";
+};
+
+&emmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins_1 &emmc_pins_2
+ &emmc_pins_3 &emmc_pins_4>;
+ fifo-depth = <256>;
+ clock-frequency = <200000000>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ non-removable;
+ bus-width = <8>;
+ status = "okay";
};
&gmac1 {
&gpio1 {
status = "okay";
- gpio-line-names = "LS-GPIO-E", "",
+ gpio-line-names = "GPIO-E", "",
"", "",
- "", "LS-GPIO-F",
- "", "LS-GPIO-J";
+ "", "GPIO-F",
+ "", "GPIO-J";
};
&gpio2 {
status = "okay";
- gpio-line-names = "LS-GPIO-H", "LS-GPIO-I",
- "LS-GPIO-L", "LS-GPIO-G",
- "LS-GPIO-K", "",
+ gpio-line-names = "GPIO-H", "GPIO-I",
+ "GPIO-L", "GPIO-G",
+ "GPIO-K", "",
"", "";
};
status = "okay";
gpio-line-names = "", "",
"", "",
- "LS-GPIO-C", "",
- "", "LS-GPIO-B";
+ "GPIO-C", "",
+ "", "GPIO-B";
};
&gpio4 {
status = "okay";
gpio-line-names = "", "",
"", "",
- "", "LS-GPIO-D",
+ "", "GPIO-D",
"", "";
};
status = "okay";
gpio-line-names = "", "USER-LED-1",
"USER-LED-2", "",
- "", "LS-GPIO-A",
+ "", "GPIO-A",
"", "";
};
status = "okay";
};
+&ohci {
+ status = "okay";
+};
+
+&pcie {
+ reset-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+ vpcie-supply = <®_pcie>;
+ status = "okay";
+};
+
+&sd0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ status = "okay";
+};
+
&spi0 {
status = "okay";
label = "LS-SPI0";
-// SPDX-License-Identifier: GPL-2.0
/*
* DTS File for HiSilicon Hi3798cv200 SoC.
*
* Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
+ *
+ * Released under the GPLv2 only.
+ * SPDX-License-Identifier: GPL-2.0
*/
#include <dt-bindings/clock/histb-clock.h>
+#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy.h>
#include <dt-bindings/reset/ti-syscon.h>
/ {
#reset-cells = <2>;
};
+ perictrl: peripheral-controller@8a20000 {
+ compatible = "hisilicon,hi3798cv200-perictrl", "syscon",
+ "simple-mfd";
+ reg = <0x8a20000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x8a20000 0x1000>;
+
+ usb2_phy1: usb2-phy@120 {
+ compatible = "hisilicon,hi3798cv200-usb2-phy";
+ reg = <0x120 0x4>;
+ clocks = <&crg HISTB_USB2_PHY1_REF_CLK>;
+ resets = <&crg 0xbc 4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb2_phy1_port0: phy@0 {
+ reg = <0>;
+ #phy-cells = <0>;
+ resets = <&crg 0xbc 8>;
+ };
+
+ usb2_phy1_port1: phy@1 {
+ reg = <1>;
+ #phy-cells = <0>;
+ resets = <&crg 0xbc 9>;
+ };
+ };
+
+ usb2_phy2: usb2-phy@124 {
+ compatible = "hisilicon,hi3798cv200-usb2-phy";
+ reg = <0x124 0x4>;
+ clocks = <&crg HISTB_USB2_PHY2_REF_CLK>;
+ resets = <&crg 0xbc 6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb2_phy2_port0: phy@0 {
+ reg = <0>;
+ #phy-cells = <0>;
+ resets = <&crg 0xbc 10>;
+ };
+ };
+
+ combphy0: phy@850 {
+ compatible = "hisilicon,hi3798cv200-combphy";
+ reg = <0x850 0x8>;
+ #phy-cells = <1>;
+ clocks = <&crg HISTB_COMBPHY0_CLK>;
+ resets = <&crg 0x188 4>;
+ assigned-clocks = <&crg HISTB_COMBPHY0_CLK>;
+ assigned-clock-rates = <100000000>;
+ hisilicon,fixed-mode = <PHY_TYPE_USB3>;
+ };
+
+ combphy1: phy@858 {
+ compatible = "hisilicon,hi3798cv200-combphy";
+ reg = <0x858 0x8>;
+ #phy-cells = <1>;
+ clocks = <&crg HISTB_COMBPHY1_CLK>;
+ resets = <&crg 0x188 12>;
+ assigned-clocks = <&crg HISTB_COMBPHY1_CLK>;
+ assigned-clock-rates = <100000000>;
+ hisilicon,mode-select-bits = <0x0008 11 (0x3 << 11)>;
+ };
+ };
+
+ pmx0: pinconf@8a21000 {
+ compatible = "pinconf-single";
+ reg = <0x8a21000 0x180>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <7>;
+ pinctrl-single,gpio-range = <
+ &range 0 8 2 /* GPIO 0 */
+ &range 8 1 0 /* GPIO 1 */
+ &range 9 4 2
+ &range 13 1 0
+ &range 14 1 1
+ &range 15 1 0
+ &range 16 5 0 /* GPIO 2 */
+ &range 21 3 1
+ &range 24 4 1 /* GPIO 3 */
+ &range 28 2 2
+ &range 86 1 1
+ &range 87 1 0
+ &range 30 4 2 /* GPIO 4 */
+ &range 34 3 0
+ &range 37 1 2
+ &range 38 3 2 /* GPIO 6 */
+ &range 41 5 0
+ &range 46 8 1 /* GPIO 7 */
+ &range 54 8 1 /* GPIO 8 */
+ &range 64 7 1 /* GPIO 9 */
+ &range 71 1 0
+ &range 72 6 1 /* GPIO 10 */
+ &range 78 1 0
+ &range 79 1 1
+ &range 80 6 1 /* GPIO 11 */
+ &range 70 2 1
+ &range 88 8 0 /* GPIO 12 */
+ >;
+
+ range: gpio-range {
+ #pinctrl-single,gpio-range-cells = <3>;
+ };
+ };
+
uart0: serial@8b00000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x8b00000 0x1000>;
status = "disabled";
};
- emmc: mmc@9830000 {
+ sd0: mmc@9820000 {
compatible = "snps,dw-mshc";
+ reg = <0x9820000 0x10000>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HISTB_SDIO0_CIU_CLK>,
+ <&crg HISTB_SDIO0_BIU_CLK>;
+ clock-names = "ciu", "biu";
+ resets = <&crg 0x9c 4>;
+ reset-names = "reset";
+ status = "disabled";
+ };
+
+ emmc: mmc@9830000 {
+ compatible = "hisilicon,hi3798cv200-dw-mshc";
reg = <0x9830000 0x10000>;
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&crg HISTB_MMC_CIU_CLK>,
- <&crg HISTB_MMC_BIU_CLK>;
- clock-names = "ciu", "biu";
+ <&crg HISTB_MMC_BIU_CLK>,
+ <&crg HISTB_MMC_SAMPLE_CLK>,
+ <&crg HISTB_MMC_DRV_CLK>;
+ clock-names = "ciu", "biu", "ciu-sample", "ciu-drive";
+ resets = <&crg 0xa0 4>;
+ reset-names = "reset";
+ status = "disabled";
};
gpio0: gpio@8b20000 {
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 0 8>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <
+ &pmx0 0 8 1
+ &pmx0 1 9 4
+ &pmx0 5 13 1
+ &pmx0 6 14 1
+ &pmx0 7 15 1
+ >;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 16 5 &pmx0 5 21 3>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <
+ &pmx0 0 24 4
+ &pmx0 4 28 2
+ &pmx0 6 86 1
+ &pmx0 7 87 1
+ >;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 30 4 &pmx0 4 34 3 &pmx0 7 37 1>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 38 3 &pmx0 0 41 5>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 46 8>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 54 8>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 64 7 &pmx0 71 1>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 72 6 &pmx0 6 78 1 &pmx0 7 79 1>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 80 6 &pmx0 6 70 2>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 88 8>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
clocks = <&sysctrl HISTB_IR_CLK>;
status = "disabled";
};
+
+ pcie: pcie@9860000 {
+ compatible = "hisilicon,hi3798cv200-pcie";
+ reg = <0x9860000 0x1000>,
+ <0x0 0x2000>,
+ <0x2000000 0x01000000>;
+ reg-names = "control", "rc-dbi", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ bus-range = <0 15>;
+ num-lanes = <1>;
+ ranges = <0x81000000 0x0 0x00000000 0x4f00000 0x0 0x100000
+ 0x82000000 0x0 0x3000000 0x3000000 0x0 0x01f00000>;
+ interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic 0 131 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HISTB_PCIE_AUX_CLK>,
+ <&crg HISTB_PCIE_PIPE_CLK>,
+ <&crg HISTB_PCIE_SYS_CLK>,
+ <&crg HISTB_PCIE_BUS_CLK>;
+ clock-names = "aux", "pipe", "sys", "bus";
+ resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>;
+ reset-names = "soft", "sys", "bus";
+ phys = <&combphy1 PHY_TYPE_PCIE>;
+ phy-names = "phy";
+ status = "disabled";
+ };
+
+ ohci: ohci@9880000 {
+ compatible = "generic-ohci";
+ reg = <0x9880000 0x10000>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HISTB_USB2_BUS_CLK>,
+ <&crg HISTB_USB2_12M_CLK>,
+ <&crg HISTB_USB2_48M_CLK>;
+ clock-names = "bus", "clk12", "clk48";
+ resets = <&crg 0xb8 12>;
+ reset-names = "bus";
+ phys = <&usb2_phy1_port0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci: ehci@9890000 {
+ compatible = "generic-ehci";
+ reg = <0x9890000 0x10000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HISTB_USB2_BUS_CLK>,
+ <&crg HISTB_USB2_PHY_CLK>,
+ <&crg HISTB_USB2_UTMI_CLK>;
+ clock-names = "bus", "phy", "utmi";
+ resets = <&crg 0xb8 12>,
+ <&crg 0xb8 16>,
+ <&crg 0xb8 13>;
+ reset-names = "bus", "phy", "utmi";
+ phys = <&usb2_phy1_port0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
};
};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Pinctrl dts file for HiSilicon Poplar board
+ *
+ * Copyright (c) 2016-2018 HiSilicon Technologies Co., Ltd.
+ */
+
+#include <dt-bindings/pinctrl/hisi.h>
+
+/* value, enable bits, disable bits, mask */
+#define PINCTRL_PULLDOWN(value, enable, disable, mask) \
+ (value << 13) (enable << 13) (disable << 13) (mask << 13)
+#define PINCTRL_PULLUP(value, enable, disable, mask) \
+ (value << 12) (enable << 12) (disable << 12) (mask << 12)
+#define PINCTRL_SLEW_RATE(value, mask) (value << 8) (mask << 8)
+#define PINCTRL_DRV_STRENGTH(value, mask) (value << 4) (mask << 4)
+
+&pmx0 {
+ emmc_pins_1: emmc-pins-1 {
+ pinctrl-single,pins = <
+ 0x000 MUX_M2
+ 0x004 MUX_M2
+ 0x008 MUX_M2
+ 0x00c MUX_M2
+ 0x010 MUX_M2
+ 0x014 MUX_M2
+ 0x018 MUX_M2
+ 0x01c MUX_M2
+ 0x024 MUX_M2
+ >;
+ pinctrl-single,bias-pulldown = <
+ PINCTRL_PULLDOWN(0, 1, 0, 1)
+ >;
+ pinctrl-single,bias-pullup = <
+ PINCTRL_PULLUP(0, 1, 0, 1)
+ >;
+ pinctrl-single,slew-rate = <
+ PINCTRL_SLEW_RATE(1, 1)
+ >;
+ pinctrl-single,drive-strength = <
+ PINCTRL_DRV_STRENGTH(0xb, 0xf)
+ >;
+ };
+
+ emmc_pins_2: emmc-pins-2 {
+ pinctrl-single,pins = <
+ 0x028 MUX_M2
+ >;
+ pinctrl-single,bias-pulldown = <
+ PINCTRL_PULLDOWN(0, 1, 0, 1)
+ >;
+ pinctrl-single,bias-pullup = <
+ PINCTRL_PULLUP(0, 1, 0, 1)
+ >;
+ pinctrl-single,slew-rate = <
+ PINCTRL_SLEW_RATE(1, 1)
+ >;
+ pinctrl-single,drive-strength = <
+ PINCTRL_DRV_STRENGTH(0x9, 0xf)
+ >;
+ };
+
+ emmc_pins_3: emmc-pins-3 {
+ pinctrl-single,pins = <
+ 0x02c MUX_M2
+ >;
+ pinctrl-single,bias-pulldown = <
+ PINCTRL_PULLDOWN(0, 1, 0, 1)
+ >;
+ pinctrl-single,bias-pullup = <
+ PINCTRL_PULLUP(0, 1, 0, 1)
+ >;
+ pinctrl-single,slew-rate = <
+ PINCTRL_SLEW_RATE(1, 1)
+ >;
+ pinctrl-single,drive-strength = <
+ PINCTRL_DRV_STRENGTH(3, 3)
+ >;
+ };
+
+ emmc_pins_4: emmc-pins-4 {
+ pinctrl-single,pins = <
+ 0x030 MUX_M2
+ >;
+ pinctrl-single,bias-pulldown = <
+ PINCTRL_PULLDOWN(1, 1, 0, 1)
+ >;
+ pinctrl-single,bias-pullup = <
+ PINCTRL_PULLUP(0, 1, 0, 1)
+ >;
+ pinctrl-single,slew-rate = <
+ PINCTRL_SLEW_RATE(1, 1)
+ >;
+ pinctrl-single,drive-strength = <
+ PINCTRL_DRV_STRENGTH(3, 3)
+ >;
+ };
+};
#define HISTB_OSC_CLK 0
#define HISTB_APB_CLK 1
#define HISTB_AHB_CLK 2
-#define HISTB_UART1_CLK 3
-#define HISTB_UART2_CLK 4
-#define HISTB_UART3_CLK 5
-#define HISTB_I2C0_CLK 6
-#define HISTB_I2C1_CLK 7
-#define HISTB_I2C2_CLK 8
-#define HISTB_I2C3_CLK 9
-#define HISTB_I2C4_CLK 10
-#define HISTB_I2C5_CLK 11
-#define HISTB_SPI0_CLK 12
-#define HISTB_SPI1_CLK 13
-#define HISTB_SPI2_CLK 14
+#define HISTB_UART1_CLK 3
+#define HISTB_UART2_CLK 4
+#define HISTB_UART3_CLK 5
+#define HISTB_I2C0_CLK 6
+#define HISTB_I2C1_CLK 7
+#define HISTB_I2C2_CLK 8
+#define HISTB_I2C3_CLK 9
+#define HISTB_I2C4_CLK 10
+#define HISTB_I2C5_CLK 11
+#define HISTB_SPI0_CLK 12
+#define HISTB_SPI1_CLK 13
+#define HISTB_SPI2_CLK 14
#define HISTB_SCI_CLK 15
#define HISTB_FMC_CLK 16
#define HISTB_MMC_BIU_CLK 17
#define HISTB_SDIO0_BIU_CLK 21
#define HISTB_SDIO0_CIU_CLK 22
#define HISTB_SDIO0_DRV_CLK 23
-#define HISTB_SDIO0_SAMPLE_CLK 24
+#define HISTB_SDIO0_SAMPLE_CLK 24
#define HISTB_PCIE_AUX_CLK 25
#define HISTB_PCIE_PIPE_CLK 26
#define HISTB_PCIE_SYS_CLK 27
#define HISTB_ETH1_MAC_CLK 31
#define HISTB_ETH1_MACIF_CLK 32
#define HISTB_COMBPHY1_CLK 33
-
+#define HISTB_USB2_BUS_CLK 34
+#define HISTB_USB2_PHY_CLK 35
+#define HISTB_USB2_UTMI_CLK 36
+#define HISTB_USB2_12M_CLK 37
+#define HISTB_USB2_48M_CLK 38
+#define HISTB_USB2_OTG_UTMI_CLK 39
+#define HISTB_USB2_PHY1_REF_CLK 40
+#define HISTB_USB2_PHY2_REF_CLK 41
+#define HISTB_COMBPHY0_CLK 42
+#define HISTB_USB3_BUS_CLK 43
+#define HISTB_USB3_UTMI_CLK 44
+#define HISTB_USB3_PIPE_CLK 45
+#define HISTB_USB3_SUSPEND_CLK 46
+#define HISTB_USB3_BUS_CLK1 47
+#define HISTB_USB3_UTMI_CLK1 48
+#define HISTB_USB3_PIPE_CLK1 49
+#define HISTB_USB3_SUSPEND_CLK1 50
/* clocks provided by mcu CRG */
-#define HISTB_MCE_CLK 1
-#define HISTB_IR_CLK 2
-#define HISTB_TIMER01_CLK 3
-#define HISTB_LEDC_CLK 4
-#define HISTB_UART0_CLK 5
-#define HISTB_LSADC_CLK 6
+#define HISTB_MCE_CLK 1
+#define HISTB_IR_CLK 2
+#define HISTB_TIMER01_CLK 3
+#define HISTB_LEDC_CLK 4
+#define HISTB_UART0_CLK 5
+#define HISTB_LSADC_CLK 6
#endif /* __DTS_HISTB_CLOCK_H */
--- /dev/null
+/*
+ * This header provides constants for hisilicon pinctrl bindings.
+ *
+ * Copyright (c) 2015 Hisilicon Limited.
+ * Copyright (c) 2015 Linaro Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_HISI_H
+#define _DT_BINDINGS_PINCTRL_HISI_H
+
+/* iomg bit definition */
+#define MUX_M0 0
+#define MUX_M1 1
+#define MUX_M2 2
+#define MUX_M3 3
+#define MUX_M4 4
+#define MUX_M5 5
+#define MUX_M6 6
+#define MUX_M7 7
+
+/* iocg bit definition */
+#define PULL_MASK (3)
+#define PULL_DIS (0)
+#define PULL_UP (1 << 0)
+#define PULL_DOWN (1 << 1)
+
+/* drive strength definition */
+#define DRIVE_MASK (7 << 4)
+#define DRIVE1_02MA (0 << 4)
+#define DRIVE1_04MA (1 << 4)
+#define DRIVE1_08MA (2 << 4)
+#define DRIVE1_10MA (3 << 4)
+#define DRIVE2_02MA (0 << 4)
+#define DRIVE2_04MA (1 << 4)
+#define DRIVE2_08MA (2 << 4)
+#define DRIVE2_10MA (3 << 4)
+#define DRIVE3_04MA (0 << 4)
+#define DRIVE3_08MA (1 << 4)
+#define DRIVE3_12MA (2 << 4)
+#define DRIVE3_16MA (3 << 4)
+#define DRIVE3_20MA (4 << 4)
+#define DRIVE3_24MA (5 << 4)
+#define DRIVE3_32MA (6 << 4)
+#define DRIVE3_40MA (7 << 4)
+#define DRIVE4_02MA (0 << 4)
+#define DRIVE4_04MA (2 << 4)
+#define DRIVE4_08MA (4 << 4)
+#define DRIVE4_10MA (6 << 4)
+
+/* drive strength definition for hi3660 */
+#define DRIVE6_MASK (15 << 4)
+#define DRIVE6_04MA (0 << 4)
+#define DRIVE6_12MA (4 << 4)
+#define DRIVE6_19MA (8 << 4)
+#define DRIVE6_27MA (10 << 4)
+#define DRIVE6_32MA (15 << 4)
+#define DRIVE7_02MA (0 << 4)
+#define DRIVE7_04MA (1 << 4)
+#define DRIVE7_06MA (2 << 4)
+#define DRIVE7_08MA (3 << 4)
+#define DRIVE7_10MA (4 << 4)
+#define DRIVE7_12MA (5 << 4)
+#define DRIVE7_14MA (6 << 4)
+#define DRIVE7_16MA (7 << 4)
+#endif
projects / u-boot.git / commitdiff