These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
config TARGET_MPC8349ITX
bool "Support MPC8349ITX"
-config TARGET_MPC8360EMDS
- bool "Support MPC8360EMDS"
-
-config TARGET_MPC8360ERDK
- bool "Support MPC8360ERDK"
-
config TARGET_MPC837XEMDS
bool "Support MPC837XEMDS"
source "board/freescale/mpc832xemds/Kconfig"
source "board/freescale/mpc8349emds/Kconfig"
source "board/freescale/mpc8349itx/Kconfig"
-source "board/freescale/mpc8360emds/Kconfig"
-source "board/freescale/mpc8360erdk/Kconfig"
source "board/freescale/mpc837xemds/Kconfig"
source "board/freescale/mpc837xerdb/Kconfig"
source "board/ids/ids8313/Kconfig"
#endif
#if defined(CONFIG_PQ_MDS_PIB_ATM)
-#if defined(CONFIG_MPC8360EMDS) || defined(CONFIG_MPC8569MDS)
+#if defined(CONFIG_MPC8569MDS)
val8 = 0;
i2c_write(0x20, 0x6, 1, &val8, 1);
i2c_write(0x20, 0x7, 1, &val8, 1);
+++ /dev/null
-if TARGET_MPC8360EMDS
-
-config SYS_BOARD
- default "mpc8360emds"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "MPC8360EMDS"
-
-endif
+++ /dev/null
-MPC8360EMDS BOARD
-M: Dave Liu <daveliu@freescale.com>
-S: Maintained
-F: board/freescale/mpc8360emds/
-F: include/configs/MPC8360EMDS.h
-F: configs/MPC8360EMDS_33_defconfig
-F: configs/MPC8360EMDS_33_ATM_defconfig
-F: configs/MPC8360EMDS_33_HOST_33_defconfig
-F: configs/MPC8360EMDS_33_HOST_66_defconfig
-F: configs/MPC8360EMDS_33_SLAVE_defconfig
-F: configs/MPC8360EMDS_66_defconfig
-F: configs/MPC8360EMDS_66_ATM_defconfig
-F: configs/MPC8360EMDS_66_HOST_33_defconfig
-F: configs/MPC8360EMDS_66_HOST_66_defconfig
-F: configs/MPC8360EMDS_66_SLAVE_defconfig
+++ /dev/null
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += mpc8360emds.o
-obj-$(CONFIG_PCI) += pci.o
+++ /dev/null
-Freescale MPC8360EMDS Board
------------------------------------------
-1. Board Switches and Jumpers
-1.0 There are four Dual-In-Line Packages(DIP) Switches on MPC8360EMDS board
- For some reason, the HW designers describe the switch settings
- in terms of 0 and 1, and then map that to physical switches where
- the label "On" refers to logic 0 and "Off" is logic 1.
-
- Switch bits are numbered 1 through, like, 4 6 8 or 10, but the
- bits may contribute to signals that are numbered based at 0,
- and some of those signals may be high-bit-number-0 too. Heed
- well the names and labels and do not get confused.
-
- "Off" == 1
- "On" == 0
-
- SW18 is switch 18 as silk-screened onto the board.
- SW4[8] is the bit labeled 8 on Switch 4.
- SW2[1:6] refers to bits labeled 1 through 6 in order on switch 2.
- SW3[7:1] refers to bits labeled 7 through 1 in order on switch 3.
- SW3[1:8]= 0000_0001 refers to bits labeled 1 through 6 is set as "On"
- and bits labeled 8 is set as "Off".
-
-1.1 There are three type boards for MPC8360E silicon up to now, They are
-
- * MPC8360E-MDS-PB PROTO (a.k.a 8360SYS PROTOTYPE)
- * MPC8360E-MDS-PB PILOT (a.k.a 8360SYS PILOT)
- * MPC8360EA-MDS-PB PROTO (a.k.a 8360SYS2 PROTOTYPE)
-
-1.2 For all the MPC8360EMDS Board
-
- First, make sure the board default setting is consistent with the
- document shipped with your board. Then apply the following setting:
- SW3[1-8]= 0000_0100 (HRCW setting value is performed on local bus)
- SW4[1-8]= 0011_0000 (Flash boot on local bus)
- SW9[1-8]= 0110_0110 (PCI Mode enabled. HRCW is read from FLASH)
- SW10[1-8]= 0000_1000 (core PLL setting)
- SW11[1-8]= 0000_0100 (SW11 is on the another side of the board)
- JP6 1-2
- on board Oscillator: 66M
-
-1.3 Since different board/chip rev. combinations have AC timing issues,
- u-boot forces RGMII-ID (RGMII with Internal Delay) mode on by default
- by the patch (mpc83xx: Disable G1TXCLK, G2TXCLK h/w buffers).
-
- When the rev2.x silicon mount on these boards, and if you are using
- u-boot version after this patch, to make the ethernet interfaces usable,
- and to enable RGMII-ID on your board, you have to setup the jumpers
- correctly.
-
- * MPC8360E-MDS-PB PROTO
- nothing to do
- * MPC8360E-MDS-PB PILOT
- JP9 and JP8 should be ON
- * MPC8360EA-MDS-PB PROTO
- JP2 and JP3 should be ON
-
-2. Memory Map
-
-2.1. The memory map should look pretty much like this:
-
- 0x0000_0000 0x7fff_ffff DDR 2G
- 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M
- 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M
- 0xc000_0000 0xdfff_ffff Empty 512M
- 0xe000_0000 0xe01f_ffff Int Mem Reg Space 2M
- 0xe020_0000 0xe02f_ffff Empty 1M
- 0xe030_0000 0xe03f_ffff PCI IO 1M
- 0xe040_0000 0xefff_ffff Empty 252M
- 0xf000_0000 0xf3ff_ffff Local Bus SDRAM 64M
- 0xf400_0000 0xf7ff_ffff Empty 64M
- 0xf800_0000 0xf800_7fff BCSR on CS1 32K
- 0xf800_8000 0xf800_ffff PIB CS4 32K
- 0xf801_0000 0xf801_7fff PIB CS5 32K
- 0xfe00_0000 0xfeff_ffff FLASH on CS0 16M
-
-
-3. Definitions
-
-3.1 Explanation of NEW definitions in:
-
- include/configs/MPC8360EMDS.h
-
- CONFIG_MPC83xx MPC83xx family for both MPC8349 and MPC8360
- CONFIG_MPC8360 MPC8360 specific
- CONFIG_MPC8360EMDS MPC8360EMDS board specific
-
-4. Compilation
-
- MPC8360EMDS shipped with 33.33MHz or 66MHz oscillator(check U41 chip).
-
- Assuming you're using BASH shell:
-
- export CROSS_COMPILE=your-cross-compile-prefix
- cd u-boot
- make distclean
- make MPC8360EMDS_XX_config
- make
-
- MPC8360EMDS support ATM, PCI in host and slave mode.
-
- To make u-boot support ATM :
- 1) Make MPC8360EMDS_XX_ATM_config
-
- To make u-boot support PCI host 66M :
- 1) DIP SW support PCI mode as described in Section 1.1.
- 2) Make MPC8360EMDS_XX_HOST_66_config
-
- To make u-boot support PCI host 33M :
- 1) DIP SW setting is similar as Section 1.1, except for SW3[4] is 1
- 2) Make MPC8360EMDS_XX_HOST_33_config
-
- To make u-boot support PCI slave 66M :
- 1) DIP SW setting is similar as Section 1.1, except for SW9[3] is 1
- 2) Make MPC8360EMDS_XX_SLAVE_config
-
- (where XX is:
- 33 - 33.33MHz oscillator
- 66 - 66MHz oscillator)
-
-5. Downloading and Flashing Images
-
-5.0 Download over serial line using Kermit:
-
- loadb
- [Drop to kermit:
- ^\c
- send <u-boot-bin-image>
- c
- ]
-
-
- Or via tftp:
-
- tftp 10000 u-boot.bin
-
-5.1 Reflash U-boot Image using U-boot
-
- tftp 20000 u-boot.bin
- protect off fef00000 fef3ffff
- erase fef00000 fef3ffff
-
- cp.b 20000 fef00000 xxxx
-
- or
-
- cp.b 20000 fef00000 3ffff
-
-
-You have to supply the correct byte count with 'xxxx' from the TFTP result log.
-Maybe 3ffff will work too, that corresponds to the erased sectors.
-
-
-6. Notes
- 1) The console baudrate for MPC8360EMDS is 115200bps.
+++ /dev/null
-/*
- * Copyright (C) 2006,2010-2011 Freescale Semiconductor, Inc.
- * Dave Liu <daveliu@freescale.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc83xx.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <phy.h>
-#include <fsl_mdio.h>
-#if defined(CONFIG_PCI)
-#include <pci.h>
-#endif
-#include <spd_sdram.h>
-#include <asm/mmu.h>
-#include <asm/io.h>
-#include <asm/mmu.h>
-#if defined(CONFIG_OF_LIBFDT)
-#include <libfdt.h>
-#endif
-#include <hwconfig.h>
-#include <fdt_support.h>
-#if defined(CONFIG_PQ_MDS_PIB)
-#include "../common/pq-mds-pib.h"
-#endif
-#include "../../../drivers/qe/uec.h"
-
-const qe_iop_conf_t qe_iop_conf_tab[] = {
- /* GETH1 */
- {0, 3, 1, 0, 1}, /* TxD0 */
- {0, 4, 1, 0, 1}, /* TxD1 */
- {0, 5, 1, 0, 1}, /* TxD2 */
- {0, 6, 1, 0, 1}, /* TxD3 */
- {1, 6, 1, 0, 3}, /* TxD4 */
- {1, 7, 1, 0, 1}, /* TxD5 */
- {1, 9, 1, 0, 2}, /* TxD6 */
- {1, 10, 1, 0, 2}, /* TxD7 */
- {0, 9, 2, 0, 1}, /* RxD0 */
- {0, 10, 2, 0, 1}, /* RxD1 */
- {0, 11, 2, 0, 1}, /* RxD2 */
- {0, 12, 2, 0, 1}, /* RxD3 */
- {0, 13, 2, 0, 1}, /* RxD4 */
- {1, 1, 2, 0, 2}, /* RxD5 */
- {1, 0, 2, 0, 2}, /* RxD6 */
- {1, 4, 2, 0, 2}, /* RxD7 */
- {0, 7, 1, 0, 1}, /* TX_EN */
- {0, 8, 1, 0, 1}, /* TX_ER */
- {0, 15, 2, 0, 1}, /* RX_DV */
- {0, 16, 2, 0, 1}, /* RX_ER */
- {0, 0, 2, 0, 1}, /* RX_CLK */
- {2, 9, 1, 0, 3}, /* GTX_CLK - CLK10 */
- {2, 8, 2, 0, 1}, /* GTX125 - CLK9 */
- /* GETH2 */
- {0, 17, 1, 0, 1}, /* TxD0 */
- {0, 18, 1, 0, 1}, /* TxD1 */
- {0, 19, 1, 0, 1}, /* TxD2 */
- {0, 20, 1, 0, 1}, /* TxD3 */
- {1, 2, 1, 0, 1}, /* TxD4 */
- {1, 3, 1, 0, 2}, /* TxD5 */
- {1, 5, 1, 0, 3}, /* TxD6 */
- {1, 8, 1, 0, 3}, /* TxD7 */
- {0, 23, 2, 0, 1}, /* RxD0 */
- {0, 24, 2, 0, 1}, /* RxD1 */
- {0, 25, 2, 0, 1}, /* RxD2 */
- {0, 26, 2, 0, 1}, /* RxD3 */
- {0, 27, 2, 0, 1}, /* RxD4 */
- {1, 12, 2, 0, 2}, /* RxD5 */
- {1, 13, 2, 0, 3}, /* RxD6 */
- {1, 11, 2, 0, 2}, /* RxD7 */
- {0, 21, 1, 0, 1}, /* TX_EN */
- {0, 22, 1, 0, 1}, /* TX_ER */
- {0, 29, 2, 0, 1}, /* RX_DV */
- {0, 30, 2, 0, 1}, /* RX_ER */
- {0, 31, 2, 0, 1}, /* RX_CLK */
- {2, 2, 1, 0, 2}, /* GTX_CLK = CLK10 */
- {2, 3, 2, 0, 1}, /* GTX125 - CLK4 */
-
- {0, 1, 3, 0, 2}, /* MDIO */
- {0, 2, 1, 0, 1}, /* MDC */
-
- {5, 0, 1, 0, 2}, /* UART2_SOUT */
- {5, 1, 2, 0, 3}, /* UART2_CTS */
- {5, 2, 1, 0, 1}, /* UART2_RTS */
- {5, 3, 2, 0, 2}, /* UART2_SIN */
-
- {0, 0, 0, 0, QE_IOP_TAB_END}, /* END of table */
-};
-
-/* Handle "mpc8360ea rev.2.1 erratum 2: RGMII Timing"? */
-static int board_handle_erratum2(void)
-{
- const immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
-
- return REVID_MAJOR(immr->sysconf.spridr) == 2 &&
- REVID_MINOR(immr->sysconf.spridr) == 1;
-}
-
-int board_early_init_f(void)
-{
- const immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- u8 *bcsr = (u8 *)CONFIG_SYS_BCSR;
-
- /* Enable flash write */
- bcsr[0xa] &= ~0x04;
-
- /* Disable G1TXCLK, G2TXCLK h/w buffers (rev.2.x h/w bug workaround) */
- if (REVID_MAJOR(immr->sysconf.spridr) == 2)
- bcsr[0xe] = 0x30;
-
- /* Enable second UART */
- bcsr[0x9] &= ~0x01;
-
- if (board_handle_erratum2()) {
- void *immap = (immap_t *)(CONFIG_SYS_IMMR + 0x14a8);
-
- /*
- * IMMR + 0x14A8[4:5] = 11 (clk delay for UCC 2)
- * IMMR + 0x14A8[18:19] = 11 (clk delay for UCC 1)
- */
- setbits_be32(immap, 0x0c003000);
-
- /*
- * IMMR + 0x14AC[20:27] = 10101010
- * (data delay for both UCC's)
- */
- clrsetbits_be32(immap + 4, 0xff0, 0xaa0);
- }
- return 0;
-}
-
-int board_early_init_r(void)
-{
- gd_t *gd;
-#ifdef CONFIG_PQ_MDS_PIB
- pib_init();
-#endif
- /*
- * BAT6 is used for SDRAM when DDR size is 512MB or larger than 256MB
- * So re-setup PCI MEM space used BAT5 after relocated to DDR
- */
- gd = (gd_t *)(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
- if (gd->ram_size > CONFIG_MAX_MEM_MAPPED) {
- write_bat(DBAT5, CONFIG_SYS_DBAT6U, CONFIG_SYS_DBAT6L);
- write_bat(IBAT5, CONFIG_SYS_IBAT6U, CONFIG_SYS_IBAT6L);
- }
-
- return 0;
-}
-
-#ifdef CONFIG_UEC_ETH
-static uec_info_t uec_info[] = {
-#ifdef CONFIG_UEC_ETH1
- STD_UEC_INFO(1),
-#endif
-#ifdef CONFIG_UEC_ETH2
- STD_UEC_INFO(2),
-#endif
-};
-
-int board_eth_init(bd_t *bd)
-{
- if (board_handle_erratum2()) {
- int i;
-
- for (i = 0; i < ARRAY_SIZE(uec_info); i++) {
- uec_info[i].enet_interface_type =
- PHY_INTERFACE_MODE_RGMII_RXID;
- uec_info[i].speed = SPEED_1000;
- }
- }
- return uec_eth_init(bd, uec_info, ARRAY_SIZE(uec_info));
-}
-#endif /* CONFIG_UEC_ETH */
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
-extern void ddr_enable_ecc(unsigned int dram_size);
-#endif
-int fixed_sdram(void);
-static int sdram_init(unsigned int base);
-
-phys_size_t initdram(int board_type)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- u32 msize = 0;
- u32 lbc_sdram_size;
-
- if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
- return -1;
-
- /* DDR SDRAM - Main SODIMM */
- im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR;
-#if defined(CONFIG_SPD_EEPROM)
- msize = spd_sdram();
-#else
- msize = fixed_sdram();
-#endif
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- /*
- * Initialize DDR ECC byte
- */
- ddr_enable_ecc(msize * 1024 * 1024);
-#endif
- /*
- * Initialize SDRAM if it is on local bus.
- */
- lbc_sdram_size = sdram_init(msize * 1024 * 1024);
- if (!msize)
- msize = lbc_sdram_size;
-
- /* return total bus SDRAM size(bytes) -- DDR */
- return (msize * 1024 * 1024);
-}
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*************************************************************************
- * fixed sdram init -- doesn't use serial presence detect.
- ************************************************************************/
-int fixed_sdram(void)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- u32 msize = CONFIG_SYS_DDR_SIZE;
- u32 ddr_size = msize << 20;
- u32 ddr_size_log2 = __ilog2(ddr_size);
- u32 half_ddr_size = ddr_size >> 1;
-
- im->sysconf.ddrlaw[0].bar =
- CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000;
- im->sysconf.ddrlaw[0].ar =
- LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE);
-#if (CONFIG_SYS_DDR_SIZE != 256)
-#warning Currenly any ddr size other than 256 is not supported
-#endif
-#ifdef CONFIG_DDR_II
- im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
- im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
- im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
- im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
- im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
- im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
- im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
- im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
- im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
- im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
- im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
- im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CNTL;
-#else
-
-#if ((CONFIG_SYS_DDR_SDRAM_BASE & 0x00FFFFFF) != 0)
-#warning Chip select bounds is only configurable in 16MB increments
-#endif
- im->ddr.csbnds[0].csbnds =
- ((CONFIG_SYS_DDR_SDRAM_BASE >> CSBNDS_SA_SHIFT) & CSBNDS_SA) |
- (((CONFIG_SYS_DDR_SDRAM_BASE + half_ddr_size - 1) >>
- CSBNDS_EA_SHIFT) & CSBNDS_EA);
- im->ddr.csbnds[1].csbnds =
- (((CONFIG_SYS_DDR_SDRAM_BASE + half_ddr_size) >>
- CSBNDS_SA_SHIFT) & CSBNDS_SA) |
- (((CONFIG_SYS_DDR_SDRAM_BASE + ddr_size - 1) >>
- CSBNDS_EA_SHIFT) & CSBNDS_EA);
-
- im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
- im->ddr.cs_config[1] = CONFIG_SYS_DDR_CS1_CONFIG;
-
- im->ddr.cs_config[2] = 0;
- im->ddr.cs_config[3] = 0;
-
- im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
- im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
- im->ddr.sdram_cfg = CONFIG_SYS_DDR_CONTROL;
-
- im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
- im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
-#endif
- udelay(200);
- im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
-
- return msize;
-}
-#endif /*!CONFIG_SYS_SPD_EEPROM */
-
-int checkboard(void)
-{
- puts("Board: Freescale MPC8360EMDS\n");
- return 0;
-}
-
-/*
- * if MPC8360EMDS is soldered with SDRAM
- */
-#ifdef CONFIG_SYS_LB_SDRAM
-/*
- * Initialize SDRAM memory on the Local Bus.
- */
-
-static int sdram_init(unsigned int base)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- fsl_lbc_t *lbc = LBC_BASE_ADDR;
- const int sdram_size = CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024;
- int rem = base % sdram_size;
- uint *sdram_addr;
-
- /* window base address should be aligned to the window size */
- if (rem)
- base = base - rem + sdram_size;
-
- /*
- * Setup BAT6 for SDRAM when DDR size is 512MB or larger than 256MB
- * After relocated to DDR, reuse BAT5 for PCI MEM space
- */
- if (base > CONFIG_MAX_MEM_MAPPED) {
- unsigned long batl = base | BATL_PP_10 | BATL_MEMCOHERENCE;
- unsigned long batu = base | BATU_BL_64M | BATU_VS | BATU_VP;
-
- /* Setup the BAT6 for SDRAM */
- write_bat(DBAT6, batu, batl);
- write_bat(IBAT6, batu, batl);
- }
-
- sdram_addr = (uint *)base;
- /*
- * Setup SDRAM Base and Option Registers
- */
- set_lbc_br(2, base | CONFIG_SYS_BR2);
- set_lbc_or(2, CONFIG_SYS_OR2);
- immap->sysconf.lblaw[2].bar = base;
- immap->sysconf.lblaw[2].ar = CONFIG_SYS_LBLAWAR2;
-
- /*setup mtrpt, lsrt and lbcr for LB bus */
- lbc->lbcr = CONFIG_SYS_LBC_LBCR;
- lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
- lbc->lsrt = CONFIG_SYS_LBC_LSRT;
- asm("sync");
-
- /*
- * Configure the SDRAM controller Machine Mode Register.
- */
- lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_5; /* Normal Operation */
- lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_1; /* Precharge All Banks */
- asm("sync");
- *sdram_addr = 0xff;
- udelay(100);
-
- /*
- * We need do 8 times auto refresh operation.
- */
- lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_2;
- asm("sync");
- *sdram_addr = 0xff; /* 1 times */
- udelay(100);
- *sdram_addr = 0xff; /* 2 times */
- udelay(100);
- *sdram_addr = 0xff; /* 3 times */
- udelay(100);
- *sdram_addr = 0xff; /* 4 times */
- udelay(100);
- *sdram_addr = 0xff; /* 5 times */
- udelay(100);
- *sdram_addr = 0xff; /* 6 times */
- udelay(100);
- *sdram_addr = 0xff; /* 7 times */
- udelay(100);
- *sdram_addr = 0xff; /* 8 times */
- udelay(100);
-
- /* Mode register write operation */
- lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_4;
- asm("sync");
- *(sdram_addr + 0xcc) = 0xff;
- udelay(100);
-
- /* Normal operation */
- lbc->lsdmr = CONFIG_SYS_LBC_LSDMR_5 | 0x40000000;
- asm("sync");
- *sdram_addr = 0xff;
- udelay(100);
-
- /*
- * In non-aligned case we don't [normally] use that memory because
- * there is a hole.
- */
- if (rem)
- return 0;
- return CONFIG_SYS_LBC_SDRAM_SIZE;
-}
-#else
-static int sdram_init(unsigned int base) { return 0; }
-#endif
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-static void ft_board_fixup_qe_usb(void *blob, bd_t *bd)
-{
- if (!hwconfig_subarg_cmp("qe_usb", "mode", "peripheral"))
- return;
-
- do_fixup_by_compat(blob, "fsl,mpc8323-qe-usb", "mode",
- "peripheral", sizeof("peripheral"), 1);
-}
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI
- ft_pci_setup(blob, bd);
-#endif
- ft_board_fixup_qe_usb(blob, bd);
- /*
- * mpc8360ea pb mds errata 2: RGMII timing
- * if on mpc8360ea rev. 2.1,
- * change both ucc phy-connection-types from rgmii-id to rgmii-rxid
- */
- if (board_handle_erratum2()) {
- int nodeoffset;
- const char *prop;
- int path;
-
- nodeoffset = fdt_path_offset(blob, "/aliases");
- if (nodeoffset >= 0) {
-#if defined(CONFIG_HAS_ETH0)
- /* fixup UCC 1 if using rgmii-id mode */
- prop = fdt_getprop(blob, nodeoffset, "ethernet0", NULL);
- if (prop) {
- path = fdt_path_offset(blob, prop);
- prop = fdt_getprop(blob, path,
- "phy-connection-type", 0);
- if (prop && (strcmp(prop, "rgmii-id") == 0))
- fdt_fixup_phy_connection(blob, path,
- PHY_INTERFACE_MODE_RGMII_RXID);
- }
-#endif
-#if defined(CONFIG_HAS_ETH1)
- /* fixup UCC 2 if using rgmii-id mode */
- prop = fdt_getprop(blob, nodeoffset, "ethernet1", NULL);
- if (prop) {
- path = fdt_path_offset(blob, prop);
- prop = fdt_getprop(blob, path,
- "phy-connection-type", 0);
- if (prop && (strcmp(prop, "rgmii-id") == 0))
- fdt_fixup_phy_connection(blob, path,
- PHY_INTERFACE_MODE_RGMII_RXID);
- }
-#endif
- }
- }
-
- return 0;
-}
-#endif
+++ /dev/null
-/*
- * Copyright (C) 2006-2009 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * PCI Configuration space access support for MPC83xx PCI Bridge
- */
-
-#include <asm/mmu.h>
-#include <asm/io.h>
-#include <common.h>
-#include <mpc83xx.h>
-#include <pci.h>
-#include <i2c.h>
-#include <asm/fsl_i2c.h>
-#include "../common/pq-mds-pib.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static struct pci_region pci1_regions[] = {
- {
- bus_start: CONFIG_SYS_PCI1_MEM_BASE,
- phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
- size: CONFIG_SYS_PCI1_MEM_SIZE,
- flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
- },
- {
- bus_start: CONFIG_SYS_PCI1_IO_BASE,
- phys_start: CONFIG_SYS_PCI1_IO_PHYS,
- size: CONFIG_SYS_PCI1_IO_SIZE,
- flags: PCI_REGION_IO
- },
- {
- bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
- phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
- size: CONFIG_SYS_PCI1_MMIO_SIZE,
- flags: PCI_REGION_MEM
- },
-};
-
-#ifdef CONFIG_MPC83XX_PCI2
-static struct pci_region pci2_regions[] = {
- {
- bus_start: CONFIG_SYS_PCI2_MEM_BASE,
- phys_start: CONFIG_SYS_PCI2_MEM_PHYS,
- size: CONFIG_SYS_PCI2_MEM_SIZE,
- flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
- },
- {
- bus_start: CONFIG_SYS_PCI2_IO_BASE,
- phys_start: CONFIG_SYS_PCI2_IO_PHYS,
- size: CONFIG_SYS_PCI2_IO_SIZE,
- flags: PCI_REGION_IO
- },
- {
- bus_start: CONFIG_SYS_PCI2_MMIO_BASE,
- phys_start: CONFIG_SYS_PCI2_MMIO_PHYS,
- size: CONFIG_SYS_PCI2_MMIO_SIZE,
- flags: PCI_REGION_MEM
- },
-};
-#endif
-
-void pci_init_board(void)
-#ifdef CONFIG_PCISLAVE
-{
- volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
- volatile pcictrl83xx_t *pci_ctrl = &immr->pci_ctrl[0];
- struct pci_region *reg[] = { pci1_regions };
-
- /* Configure PCI Local Access Windows */
- pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
- pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_512M;
-
- pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_1M;
-
- mpc83xx_pci_init(1, reg);
-
- /*
- * Configure PCI Inbound Translation Windows
- */
- pci_ctrl[0].pitar0 = 0x0;
- pci_ctrl[0].pibar0 = 0x0;
- pci_ctrl[0].piwar0 = PIWAR_EN | PIWAR_RTT_SNOOP |
- PIWAR_WTT_SNOOP | PIWAR_IWS_4K;
-
- pci_ctrl[0].pitar1 = 0x0;
- pci_ctrl[0].pibar1 = 0x0;
- pci_ctrl[0].piebar1 = 0x0;
- pci_ctrl[0].piwar1 &= ~PIWAR_EN;
-
- pci_ctrl[0].pitar2 = 0x0;
- pci_ctrl[0].pibar2 = 0x0;
- pci_ctrl[0].piebar2 = 0x0;
- pci_ctrl[0].piwar2 &= ~PIWAR_EN;
-
- /* Unlock the configuration bit */
- mpc83xx_pcislave_unlock(0);
- printf("PCI: Agent mode enabled\n");
-}
-#else
-{
- volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
- volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
-#ifndef CONFIG_MPC83XX_PCI2
- struct pci_region *reg[] = { pci1_regions };
-#else
- struct pci_region *reg[] = { pci1_regions, pci2_regions };
-#endif
-
- /* initialize the PCA9555PW IO expander on the PIB board */
- pib_init();
-
-#if defined(CONFIG_PCI_66M)
- clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2;
- printf("PCI clock is 66MHz\n");
-#elif defined(CONFIG_PCI_33M)
- clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2 |
- OCCR_PCICD0 | OCCR_PCICD1 | OCCR_PCICD2 | OCCR_PCICR;
- printf("PCI clock is 33MHz\n");
-#else
- clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2;
- printf("PCI clock is 66MHz\n");
-#endif
- udelay(2000);
-
- /* Configure PCI Local Access Windows */
- pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
- pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_512M;
-
- pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_1M;
-
- udelay(2000);
-
-#ifndef CONFIG_MPC83XX_PCI2
- mpc83xx_pci_init(1, reg);
-#else
- mpc83xx_pci_init(2, reg);
-#endif
-}
-#endif /* CONFIG_PCISLAVE */
+++ /dev/null
-if TARGET_MPC8360ERDK
-
-config SYS_BOARD
- default "mpc8360erdk"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_CONFIG_NAME
- default "MPC8360ERDK"
-
-endif
+++ /dev/null
-MPC8360ERDK BOARD
-#M: Anton Vorontsov <avorontsov@ru.mvista.com>
-S: Orphan (since 2014-03)
-F: board/freescale/mpc8360erdk/
-F: include/configs/MPC8360ERDK.h
-F: configs/MPC8360ERDK_defconfig
-F: configs/MPC8360ERDK_33_defconfig
+++ /dev/null
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += mpc8360erdk.o
-obj-$(CONFIG_CMD_NAND) += nand.o
+++ /dev/null
-/*
- * Copyright (C) 2006 Freescale Semiconductor, Inc.
- * Dave Liu <daveliu@freescale.com>
- *
- * Copyright (C) 2007 Logic Product Development, Inc.
- * Peter Barada <peterb@logicpd.com>
- *
- * Copyright (C) 2007 MontaVista Software, Inc.
- * Anton Vorontsov <avorontsov@ru.mvista.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc83xx.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <asm/io.h>
-#include <asm/mmu.h>
-#include <pci.h>
-#include <libfdt.h>
-
-const qe_iop_conf_t qe_iop_conf_tab[] = {
- /* MDIO */
- {0, 1, 3, 0, 2}, /* MDIO */
- {0, 2, 1, 0, 1}, /* MDC */
-
- /* UCC1 - UEC (Gigabit) */
- {0, 3, 1, 0, 1}, /* TxD0 */
- {0, 4, 1, 0, 1}, /* TxD1 */
- {0, 5, 1, 0, 1}, /* TxD2 */
- {0, 6, 1, 0, 1}, /* TxD3 */
- {0, 9, 2, 0, 1}, /* RxD0 */
- {0, 10, 2, 0, 1}, /* RxD1 */
- {0, 11, 2, 0, 1}, /* RxD2 */
- {0, 12, 2, 0, 1}, /* RxD3 */
- {0, 7, 1, 0, 1}, /* TX_EN */
- {0, 8, 1, 0, 1}, /* TX_ER */
- {0, 15, 2, 0, 1}, /* RX_DV */
- {0, 0, 2, 0, 1}, /* RX_CLK */
- {2, 9, 1, 0, 3}, /* GTX_CLK - CLK10 */
- {2, 8, 2, 0, 1}, /* GTX125 - CLK9 */
-
- /* UCC2 - UEC (Gigabit) */
- {0, 17, 1, 0, 1}, /* TxD0 */
- {0, 18, 1, 0, 1}, /* TxD1 */
- {0, 19, 1, 0, 1}, /* TxD2 */
- {0, 20, 1, 0, 1}, /* TxD3 */
- {0, 23, 2, 0, 1}, /* RxD0 */
- {0, 24, 2, 0, 1}, /* RxD1 */
- {0, 25, 2, 0, 1}, /* RxD2 */
- {0, 26, 2, 0, 1}, /* RxD3 */
- {0, 21, 1, 0, 1}, /* TX_EN */
- {0, 22, 1, 0, 1}, /* TX_ER */
- {0, 29, 2, 0, 1}, /* RX_DV */
- {0, 31, 2, 0, 1}, /* RX_CLK */
- {2, 2, 1, 0, 2}, /* GTX_CLK - CLK10 */
- {2, 3, 2, 0, 1}, /* GTX125 - CLK4 */
-
- /* UCC7 - UEC */
- {4, 0, 1, 0, 1}, /* TxD0 */
- {4, 1, 1, 0, 1}, /* TxD1 */
- {4, 2, 1, 0, 1}, /* TxD2 */
- {4, 3, 1, 0, 1}, /* TxD3 */
- {4, 6, 2, 0, 1}, /* RxD0 */
- {4, 7, 2, 0, 1}, /* RxD1 */
- {4, 8, 2, 0, 1}, /* RxD2 */
- {4, 9, 2, 0, 1}, /* RxD3 */
- {4, 4, 1, 0, 1}, /* TX_EN */
- {4, 5, 1, 0, 1}, /* TX_ER */
- {4, 12, 2, 0, 1}, /* RX_DV */
- {4, 13, 2, 0, 1}, /* RX_ER */
- {4, 10, 2, 0, 1}, /* COL */
- {4, 11, 2, 0, 1}, /* CRS */
- {2, 18, 2, 0, 1}, /* TX_CLK - CLK19 */
- {2, 19, 2, 0, 1}, /* RX_CLK - CLK20 */
-
- /* UCC4 - UEC */
- {1, 14, 1, 0, 1}, /* TxD0 */
- {1, 15, 1, 0, 1}, /* TxD1 */
- {1, 16, 1, 0, 1}, /* TxD2 */
- {1, 17, 1, 0, 1}, /* TxD3 */
- {1, 20, 2, 0, 1}, /* RxD0 */
- {1, 21, 2, 0, 1}, /* RxD1 */
- {1, 22, 2, 0, 1}, /* RxD2 */
- {1, 23, 2, 0, 1}, /* RxD3 */
- {1, 18, 1, 0, 1}, /* TX_EN */
- {1, 19, 1, 0, 2}, /* TX_ER */
- {1, 26, 2, 0, 1}, /* RX_DV */
- {1, 27, 2, 0, 1}, /* RX_ER */
- {1, 24, 2, 0, 1}, /* COL */
- {1, 25, 2, 0, 1}, /* CRS */
- {2, 6, 2, 0, 1}, /* TX_CLK - CLK7 */
- {2, 7, 2, 0, 1}, /* RX_CLK - CLK8 */
-
- /* PCI1 */
- {5, 4, 2, 0, 3}, /* PCI_M66EN */
- {5, 5, 1, 0, 3}, /* PCI_INTA */
- {5, 6, 1, 0, 3}, /* PCI_RSTO */
- {5, 7, 3, 0, 3}, /* PCI_C_BE0 */
- {5, 8, 3, 0, 3}, /* PCI_C_BE1 */
- {5, 9, 3, 0, 3}, /* PCI_C_BE2 */
- {5, 10, 3, 0, 3}, /* PCI_C_BE3 */
- {5, 11, 3, 0, 3}, /* PCI_PAR */
- {5, 12, 3, 0, 3}, /* PCI_FRAME */
- {5, 13, 3, 0, 3}, /* PCI_TRDY */
- {5, 14, 3, 0, 3}, /* PCI_IRDY */
- {5, 15, 3, 0, 3}, /* PCI_STOP */
- {5, 16, 3, 0, 3}, /* PCI_DEVSEL */
- {5, 17, 0, 0, 0}, /* PCI_IDSEL */
- {5, 18, 3, 0, 3}, /* PCI_SERR */
- {5, 19, 3, 0, 3}, /* PCI_PERR */
- {5, 20, 3, 0, 3}, /* PCI_REQ0 */
- {5, 21, 2, 0, 3}, /* PCI_REQ1 */
- {5, 22, 2, 0, 3}, /* PCI_GNT2 */
- {5, 23, 3, 0, 3}, /* PCI_GNT0 */
- {5, 24, 1, 0, 3}, /* PCI_GNT1 */
- {5, 25, 1, 0, 3}, /* PCI_GNT2 */
- {5, 26, 0, 0, 0}, /* PCI_CLK0 */
- {5, 27, 0, 0, 0}, /* PCI_CLK1 */
- {5, 28, 0, 0, 0}, /* PCI_CLK2 */
- {5, 29, 0, 0, 3}, /* PCI_SYNC_OUT */
- {6, 0, 3, 0, 3}, /* PCI_AD0 */
- {6, 1, 3, 0, 3}, /* PCI_AD1 */
- {6, 2, 3, 0, 3}, /* PCI_AD2 */
- {6, 3, 3, 0, 3}, /* PCI_AD3 */
- {6, 4, 3, 0, 3}, /* PCI_AD4 */
- {6, 5, 3, 0, 3}, /* PCI_AD5 */
- {6, 6, 3, 0, 3}, /* PCI_AD6 */
- {6, 7, 3, 0, 3}, /* PCI_AD7 */
- {6, 8, 3, 0, 3}, /* PCI_AD8 */
- {6, 9, 3, 0, 3}, /* PCI_AD9 */
- {6, 10, 3, 0, 3}, /* PCI_AD10 */
- {6, 11, 3, 0, 3}, /* PCI_AD11 */
- {6, 12, 3, 0, 3}, /* PCI_AD12 */
- {6, 13, 3, 0, 3}, /* PCI_AD13 */
- {6, 14, 3, 0, 3}, /* PCI_AD14 */
- {6, 15, 3, 0, 3}, /* PCI_AD15 */
- {6, 16, 3, 0, 3}, /* PCI_AD16 */
- {6, 17, 3, 0, 3}, /* PCI_AD17 */
- {6, 18, 3, 0, 3}, /* PCI_AD18 */
- {6, 19, 3, 0, 3}, /* PCI_AD19 */
- {6, 20, 3, 0, 3}, /* PCI_AD20 */
- {6, 21, 3, 0, 3}, /* PCI_AD21 */
- {6, 22, 3, 0, 3}, /* PCI_AD22 */
- {6, 23, 3, 0, 3}, /* PCI_AD23 */
- {6, 24, 3, 0, 3}, /* PCI_AD24 */
- {6, 25, 3, 0, 3}, /* PCI_AD25 */
- {6, 26, 3, 0, 3}, /* PCI_AD26 */
- {6, 27, 3, 0, 3}, /* PCI_AD27 */
- {6, 28, 3, 0, 3}, /* PCI_AD28 */
- {6, 29, 3, 0, 3}, /* PCI_AD29 */
- {6, 30, 3, 0, 3}, /* PCI_AD30 */
- {6, 31, 3, 0, 3}, /* PCI_AD31 */
-
- /* NAND */
- {4, 18, 2, 0, 0}, /* NAND_RYnBY */
-
- /* DUART - UART2 */
- {5, 0, 1, 0, 2}, /* UART2_SOUT */
- {5, 2, 1, 0, 1}, /* UART2_RTS */
- {5, 3, 2, 0, 2}, /* UART2_SIN */
- {5, 1, 2, 0, 3}, /* UART2_CTS */
-
- /* UCC5 - UART3 */
- {3, 0, 1, 0, 1}, /* UART3_TX */
- {3, 4, 1, 0, 1}, /* UART3_RTS */
- {3, 6, 2, 0, 1}, /* UART3_RX */
- {3, 12, 2, 0, 0}, /* UART3_CTS */
- {3, 13, 2, 0, 0}, /* UCC5_CD */
-
- /* UCC6 - UART4 */
- {3, 14, 1, 0, 1}, /* UART4_TX */
- {3, 18, 1, 0, 1}, /* UART4_RTS */
- {3, 20, 2, 0, 1}, /* UART4_RX */
- {3, 26, 2, 0, 0}, /* UART4_CTS */
- {3, 27, 2, 0, 0}, /* UCC6_CD */
-
- /* Fujitsu MB86277 (MINT) graphics controller */
- {0, 30, 1, 0, 0}, /* nSRESET_GRAPHICS */
- {1, 5, 1, 0, 0}, /* nXRST_GRAPHICS */
- {1, 7, 1, 0, 0}, /* LVDS_BKLT_CTR */
- {2, 16, 1, 0, 0}, /* LVDS_BKLT_EN */
-
- /* AD7843 ADC/Touchscreen controller */
- {4, 14, 1, 0, 0}, /* SPI_nCS0 */
- {4, 28, 3, 0, 3}, /* SPI_MOSI */
- {4, 29, 3, 0, 3}, /* SPI_MISO */
- {4, 30, 3, 0, 3}, /* SPI_CLK */
-
- /* Freescale QUICC Engine USB Host Controller (FHCI) */
- {1, 2, 1, 0, 3}, /* USBOE */
- {1, 3, 1, 0, 3}, /* USBTP */
- {1, 8, 1, 0, 1}, /* USBTN */
- {1, 9, 2, 1, 3}, /* USBRP */
- {1, 10, 2, 0, 3}, /* USBRXD */
- {1, 11, 2, 1, 3}, /* USBRN */
- {2, 20, 2, 0, 1}, /* CLK21 */
- {4, 20, 1, 0, 0}, /* SPEED */
- {4, 21, 1, 0, 0}, /* SUSPND */
-
- /* END of table */
- {0, 0, 0, 0, QE_IOP_TAB_END},
-};
-
-int board_early_init_r(void)
-{
- void *reg = (void *)(CONFIG_SYS_IMMR + 0x14a8);
- u32 val;
-
- /*
- * Because of errata in the UCCs, we have to write to the reserved
- * registers to slow the clocks down.
- */
- val = in_be32(reg);
- /* UCC1 */
- val |= 0x00003000;
- /* UCC2 */
- val |= 0x0c000000;
- out_be32(reg, val);
-
- return 0;
-}
-
-int fixed_sdram(void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- u32 msize = 0;
- u32 ddr_size;
- u32 ddr_size_log2;
-
- msize = CONFIG_SYS_DDR_SIZE;
- for (ddr_size = msize << 20, ddr_size_log2 = 0;
- (ddr_size > 1); ddr_size = ddr_size >> 1, ddr_size_log2++) {
- if (ddr_size & 1)
- return -1;
- }
-
- im->sysconf.ddrlaw[0].ar =
- LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE);
-
- im->ddr.csbnds[0].csbnds = CONFIG_SYS_DDR_CS0_BNDS;
- im->ddr.cs_config[0] = CONFIG_SYS_DDR_CS0_CONFIG;
- im->ddr.timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0;
- im->ddr.timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
- im->ddr.timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
- im->ddr.timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3;
- im->ddr.sdram_cfg = CONFIG_SYS_DDR_SDRAM_CFG;
- im->ddr.sdram_cfg2 = CONFIG_SYS_DDR_SDRAM_CFG2;
- im->ddr.sdram_mode = CONFIG_SYS_DDR_MODE;
- im->ddr.sdram_mode2 = CONFIG_SYS_DDR_MODE2;
- im->ddr.sdram_interval = CONFIG_SYS_DDR_INTERVAL;
- im->ddr.sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CNTL;
- udelay(200);
- im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
-
- return msize;
-}
-
-phys_size_t initdram(int board_type)
-{
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- extern void ddr_enable_ecc(unsigned int dram_size);
-#endif
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- u32 msize = 0;
-
- if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
- return -1;
-
- /* DDR SDRAM - Main SODIMM */
- im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR;
- msize = fixed_sdram();
-
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- /*
- * Initialize DDR ECC byte
- */
- ddr_enable_ecc(msize * 1024 * 1024);
-#endif
-
- /* return total bus SDRAM size(bytes) -- DDR */
- return (msize * 1024 * 1024);
-}
-
-int checkboard(void)
-{
- puts("Board: Freescale/Logic MPC8360ERDK\n");
- return 0;
-}
-
-static struct pci_region pci_regions[] = {
- {
- .bus_start = CONFIG_SYS_PCI1_MEM_BASE,
- .phys_start = CONFIG_SYS_PCI1_MEM_PHYS,
- .size = CONFIG_SYS_PCI1_MEM_SIZE,
- .flags = PCI_REGION_MEM | PCI_REGION_PREFETCH,
- },
- {
- .bus_start = CONFIG_SYS_PCI1_MMIO_BASE,
- .phys_start = CONFIG_SYS_PCI1_MMIO_PHYS,
- .size = CONFIG_SYS_PCI1_MMIO_SIZE,
- .flags = PCI_REGION_MEM,
- },
- {
- .bus_start = CONFIG_SYS_PCI1_IO_BASE,
- .phys_start = CONFIG_SYS_PCI1_IO_PHYS,
- .size = CONFIG_SYS_PCI1_IO_SIZE,
- .flags = PCI_REGION_IO,
- },
-};
-
-void pci_init_board(void)
-{
- volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
- volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
- struct pci_region *reg[] = { pci_regions, };
-
-#if defined(CONFIG_PCI_33M)
- clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2 |
- OCCR_PCICD0 | OCCR_PCICD1 | OCCR_PCICD2 | OCCR_PCICR;
- printf("PCI clock is 33MHz\n");
-#else
- clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2;
- printf("PCI clock is 66MHz\n");
-#endif
-
- udelay(2000);
-
- /* Configure PCI Local Access Windows */
- pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
- pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
-
- pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
-
- mpc83xx_pci_init(1, reg);
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
- ft_pci_setup(blob, bd);
-
- return 0;
-}
-#endif
+++ /dev/null
-/*
- * MPC8360E-RDK support for the NAND on FSL UPM
- *
- * Copyright (C) 2007 MontaVista Software, Inc.
- * Anton Vorontsov <avorontsov@ru.mvista.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <common.h>
-#include <asm/io.h>
-#include <asm/immap_83xx.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/fsl_upm.h>
-#include <nand.h>
-
-static struct immap *im = (struct immap *)CONFIG_SYS_IMMR;
-
-static const u32 upm_array[] = {
- 0x0ff03c30, 0x0ff03c30, 0x0ff03c34, 0x0ff33c30, /* Words 0 to 3 */
- 0xfff33c31, 0xfffffc30, 0xfffffc30, 0xfffffc30, /* Words 4 to 7 */
- 0x0faf3c30, 0x0faf3c30, 0x0faf3c30, 0x0fff3c34, /* Words 8 to 11 */
- 0xffff3c31, 0xfffffc30, 0xfffffc30, 0xfffffc30, /* Words 12 to 15 */
- 0x0fa3fc30, 0x0fa3fc30, 0x0fa3fc30, 0x0ff3fc34, /* Words 16 to 19 */
- 0xfff3fc31, 0xfffffc30, 0xfffffc30, 0xfffffc30, /* Words 20 to 23 */
- 0x0ff33c30, 0x0fa33c30, 0x0fa33c34, 0x0ff33c30, /* Words 24 to 27 */
- 0xfff33c31, 0xfff0fc30, 0xfff0fc30, 0xfff0fc30, /* Words 28 to 31 */
- 0xfff3fc30, 0xfff3fc30, 0xfff6fc30, 0xfffcfc30, /* Words 32 to 35 */
- 0xfffcfc30, 0xfffcfc30, 0xfffcfc30, 0xfffcfc30, /* Words 36 to 39 */
- 0xfffcfc30, 0xfffcfc30, 0xfffcfc30, 0xfffcfc30, /* Words 40 to 43 */
- 0xfffdfc30, 0xfffffc30, 0xfffffc30, 0xfffffc31, /* Words 44 to 47 */
- 0xfffffc30, 0xfffffc00, 0xfffffc00, 0xfffffc00, /* Words 48 to 51 */
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, /* Words 52 to 55 */
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, /* Words 56 to 59 */
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, /* Words 60 to 63 */
-};
-
-static void upm_setup(struct fsl_upm *upm)
-{
- int i;
-
- /* write upm array */
- out_be32(upm->mxmr, MxMR_OP_WARR);
-
- for (i = 0; i < 64; i++) {
- out_be32(upm->mdr, upm_array[i]);
- out_8(upm->io_addr, 0x0);
- }
-
- /* normal operation */
- out_be32(upm->mxmr, MxMR_OP_NORM);
- while (in_be32(upm->mxmr) != MxMR_OP_NORM)
- eieio();
-}
-
-static int dev_ready(int chip_nr)
-{
- if (in_be32(&im->qepio.ioport[4].pdat) & 0x00002000) {
- debug("nand ready\n");
- return 1;
- }
-
- debug("nand busy\n");
- return 0;
-}
-
-static struct fsl_upm_nand fun = {
- .upm = {
- .io_addr = (void *)CONFIG_SYS_NAND_BASE,
- },
- .width = 8,
- .upm_cmd_offset = 8,
- .upm_addr_offset = 16,
- .dev_ready = dev_ready,
- .wait_flags = FSL_UPM_WAIT_RUN_PATTERN,
- .chip_delay = 50,
-};
-
-int board_nand_init(struct nand_chip *nand)
-{
- fun.upm.mxmr = &im->im_lbc.mamr;
- fun.upm.mdr = &im->im_lbc.mdr;
- fun.upm.mar = &im->im_lbc.mar;
-
- upm_setup(&fun.upm);
-
- return fsl_upm_nand_init(nand, &fun);
-}
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_33MHZ,PQ_MDS_PIB=1,PQ_MDS_PIB_ATM=1"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360EMDS=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_33MHZ,PCI,PCI_33M,PQ_MDS_PIB=1"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360EMDS=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_33MHZ,PCI,PCI_66M,PQ_MDS_PIB=1"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360EMDS=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_33MHZ,PCI,PCISLAVE"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360EMDS=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_33MHZ"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360EMDS=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_66MHZ,PQ_MDS_PIB=1,PQ_MDS_PIB_ATM=1"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360EMDS=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_66MHZ,PCI,PCI_33M,PQ_MDS_PIB=1"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360EMDS=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_66MHZ,PCI,PCI_66M,PQ_MDS_PIB=1"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360EMDS=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_66MHZ,PCI,PCISLAVE"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360EMDS=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_66MHZ"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360EMDS=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="CLKIN_33MHZ"
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360ERDK=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_MPC83xx=y
-CONFIG_TARGET_MPC8360ERDK=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
-P3G4 powerpc 74xx_7xx - - Wolfgang Denk <wd@denx.de>
-ZUMA powerpc 74xx_7xx - - Nye Liu <nyet@zumanetworks.com>
-ppmc7xx powerpc 74xx_7xx - -
-ELPPC powerpc 74xx_7xx - -
-mpc7448hpc2 powerpc 74xx_7xx - - Roy Zang <tie-fei.zang@freescale.com>
+MPC8360EMDS powerpc mpc83xx - - Dave Liu <daveliu@freescale.com>
+MPC8360ERDK powerpc mpc83xx - - Anton Vorontsov <avorontsov@ru.mvista.com>
+P3G4 powerpc 74xx_7xx d928664f 2015-01-16 Wolfgang Denk <wd@denx.de>
+ZUMA powerpc 74xx_7xx d928664f 2015-01-16 Nye Liu <nyet@zumanetworks.com>
+ppmc7xx powerpc 74xx_7xx d928664f 2015-01-16
+ELPPC powerpc 74xx_7xx d928664f 2015-01-16
+mpc7448hpc2 powerpc 74xx_7xx d928664f 2015-01-16 Roy Zang <tie-fei.zang@freescale.com>
CPCI405 ppc4xx 405gp 5f1459dc 2015-01-13 Matthias Fuchs <matthias.fuchs@esd.eu>
CPCI405DT ppc4xx 405gpr 5f1459dc 2015-01-13 Matthias Fuchs <matthias.fuchs@esd.eu>
CPCI405AB ppc4xx 405gpr 5f1459dc 2015-01-13 Matthias Fuchs <matthias.fuchs@esd.eu>
+++ /dev/null
-/*
- * Copyright (C) 2006,2011 Freescale Semiconductor, Inc.
- *
- * Dave Liu <daveliu@freescale.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-#define CONFIG_QE 1 /* Has QE */
-#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
-#define CONFIG_MPC8360EMDS 1 /* MPC8360EMDS board specific */
-
-#define CONFIG_SYS_TEXT_BASE 0xFE000000
-
-#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */
-#undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */
-
-/*
- * System Clock Setup
- */
-#ifdef CONFIG_CLKIN_33MHZ
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_83XX_PCICLK 33330000 /* in HZ */
-#else
-#define CONFIG_83XX_CLKIN 33330000 /* in Hz */
-#endif
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ 33330000
-#endif
-
-#elif defined(CONFIG_CLKIN_66MHZ)
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_83XX_PCICLK 66000000 /* in HZ */
-#else
-#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
-#endif
-
-#ifndef CONFIG_SYS_CLK_FREQ
-#define CONFIG_SYS_CLK_FREQ 66000000
-#endif
-#else
-#error Unknown oscillator frequency.
-#endif
-
-/*
- * Hardware Reset Configuration Word
- */
-#ifdef CONFIG_CLKIN_33MHZ
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN_8X1 |\
- HRCWL_VCO_1X2 |\
- HRCWL_CE_PLL_VCO_DIV_4 |\
- HRCWL_CE_PLL_DIV_1X1 |\
- HRCWL_CE_TO_PLL_1X15 |\
- HRCWL_CORE_TO_CSB_2X1)
-#elif defined(CONFIG_CLKIN_66MHZ)
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN_4X1 |\
- HRCWL_VCO_1X2 |\
- HRCWL_CE_PLL_VCO_DIV_4 |\
- HRCWL_CE_PLL_DIV_1X1 |\
- HRCWL_CE_TO_PLL_1X6 |\
- HRCWL_CORE_TO_CSB_2X1)
-#endif
-
-#ifdef CONFIG_PCISLAVE
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_AGENT |\
- HRCWH_PCI1_ARBITER_DISABLE |\
- HRCWH_PCICKDRV_DISABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0XFFF00100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT)
-#else
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_HOST |\
- HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_PCICKDRV_ENABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0X00000100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT)
-#endif
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH 0x00000000
-#define CONFIG_SYS_SICRL 0x40000000
-
-#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
-#define CONFIG_BOARD_EARLY_INIT_R
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR 0xE0000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
- /* + 256M */
-#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000)
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
- | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CONFIG_SYS_83XX_DDR_USES_CS0
-
-#define CONFIG_DDR_ECC /* support DDR ECC function */
-#define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
-
-/*
- * DDRCDR - DDR Control Driver Register
- */
-#define CONFIG_SYS_DDRCDR_VALUE 0x80080001
-
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#if defined(CONFIG_SPD_EEPROM)
-/*
- * Determine DDR configuration from I2C interface.
- */
-#define SPD_EEPROM_ADDRESS 0x52 /* DDR SODIMM */
-#else
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_SYS_DDR_SIZE 256 /* MB */
-#if defined(CONFIG_DDR_II)
-#define CONFIG_SYS_DDRCDR 0x80080001
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
-#define CONFIG_SYS_DDR_CS0_CONFIG 0x80330102
-#define CONFIG_SYS_DDR_TIMING_0 0x00220802
-#define CONFIG_SYS_DDR_TIMING_1 0x38357322
-#define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-#define CONFIG_SYS_DDR_CLK_CNTL 0x02000000
-#define CONFIG_SYS_DDR_MODE 0x47d00432
-#define CONFIG_SYS_DDR_MODE2 0x8000c000
-#define CONFIG_SYS_DDR_INTERVAL 0x03cf0080
-#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
-#else
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
- | CSCONFIG_ROW_BIT_13 \
- | CSCONFIG_COL_BIT_9)
-#define CONFIG_SYS_DDR_CS1_CONFIG CONFIG_SYS_DDR_CS0_CONFIG
-#define CONFIG_SYS_DDR_TIMING_1 0x37344321 /* tCL-tRCD-tRP-tRAS=2.5-3-3-7 */
-#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* may need tuning */
-#define CONFIG_SYS_DDR_CONTROL 0x42008000 /* Self refresh,2T timing */
-#define CONFIG_SYS_DDR_MODE 0x20000162 /* DLL,normal,seq,4/2.5 */
-#define CONFIG_SYS_DDR_INTERVAL 0x045b0100 /* page mode */
-#endif
-#endif
-
-/*
- * Memory test
- */
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
-#define CONFIG_SYS_MEMTEST_END 0x00100000
-
-/*
- * The reserved memory
- */
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
-#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
-#define CONFIG_SYS_FLASH_SIZE 32 /* max FLASH size is 32M */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
- /* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB)
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
- | BR_PS_16 /* 16 bit port */ \
- | BR_MS_GPCM /* MSEL = GPCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
- | OR_GPCM_XAM \
- | OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV2 \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-
-/*
- * BCSR on the Local Bus
- */
-#define CONFIG_SYS_BCSR 0xF8000000
- /* Access window base at BCSR base */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR
-#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_64KB)
-
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \
- | BR_PS_8 \
- | BR_MS_GPCM \
- | BR_V)
-#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \
- | OR_GPCM_XAM \
- | OR_GPCM_CSNT \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
- /* 0xFFFFE9F7 */
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */
-#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-#define CONFIG_SYS_LB_SDRAM /* if board has SRDAM on local bus */
-
-#ifdef CONFIG_SYS_LB_SDRAM
-#define CONFIG_SYS_LBLAWBAR2 0
-#define CONFIG_SYS_LBLAWAR2 (LBLAWAR_EN | LBLAWAR_64MB)
-
-/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */
-/*
- * Base Register 2 and Option Register 2 configure SDRAM.
- *
- * For BR2, need:
- * Base address = BR[0:16] = dynamic
- * port size = 32-bits = BR2[19:20] = 11
- * no parity checking = BR2[21:22] = 00
- * SDRAM for MSEL = BR2[24:26] = 011
- * Valid = BR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * xxxx xxxx xxxx xxxx x001 1000 0110 0001 = 00001861
- */
-
-/* Port size=32bit, MSEL=DRAM */
-#define CONFIG_SYS_BR2 (BR_PS_32 | BR_MS_SDRAM | BR_V) /* 0xF0001861 */
-
-/*
- * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
- *
- * For OR2, need:
- * 64MB mask for AM, OR2[0:7] = 1111 1100
- * XAM, OR2[17:18] = 11
- * 9 columns OR2[19-21] = 010
- * 13 rows OR2[23-25] = 100
- * EAD set for extra time OR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
- */
-
-#define CONFIG_SYS_OR2 (MEG_TO_AM(CONFIG_SYS_LBC_SDRAM_SIZE) \
- | OR_SDRAM_XAM \
- | ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
- | ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
- | OR_SDRAM_EAD)
- /* 0xFC006901 */
-
- /* LB sdram refresh timer, about 6us */
-#define CONFIG_SYS_LBC_LSRT 0x32000000
- /* LB refresh timer prescal, 266MHz/32 */
-#define CONFIG_SYS_LBC_MRTPR 0x20000000
-
-#define CONFIG_SYS_LBC_LSDMR_COMMON 0x0063b723
-
-/*
- * SDRAM Controller configuration sequence.
- */
-#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
-#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
-#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
-#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
-#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
-
-#endif
-
-/*
- * Windows to access Platform I/O Boards (PIB) via local bus
- */
-#define CONFIG_SYS_PIB_BASE 0xF8008000
-#define CONFIG_SYS_PIB_WINDOW_SIZE (32 * 1024)
-
-/* [RFC] This LBLAW only covers the 2nd window (CS5) */
-#define CONFIG_SYS_LBLAWBAR3_PRELIM \
- CONFIG_SYS_PIB_BASE + CONFIG_SYS_PIB_WINDOW_SIZE
-#define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
-
-/*
- * CS4 on Local Bus, to PIB
- */
- /* CS4 base address at 0xf8008000 */
-#define CONFIG_SYS_BR4_PRELIM (CONFIG_SYS_PIB_BASE \
- | BR_PS_8 \
- | BR_MS_GPCM \
- | BR_V)
- /* 0xF8008801 */
-#define CONFIG_SYS_OR4_PRELIM (OR_AM_32KB \
- | OR_GPCM_XAM \
- | OR_GPCM_CSNT \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
- /* 0xffffe9f7 */
-
-/*
- * CS5 on Local Bus, to PIB
- */
- /* CS5 base address at 0xf8010000 */
-#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_PIB_BASE + \
- CONFIG_SYS_PIB_WINDOW_SIZE) \
- | BR_PS_8 \
- | BR_MS_GPCM \
- | BR_V)
- /* 0xF8010801 */
-#define CONFIG_SYS_OR5_PRELIM (CONFIG_SYS_PIB_BASE \
- | OR_GPCM_XAM \
- | OR_GPCM_CSNT \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
- /* 0xffffe9f7 */
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} }
-
-/*
- * Config on-board RTC
- */
-#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
-#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */
-
-#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
-#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
-
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_83XX_PCI_STREAMING
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-
-#endif /* CONFIG_PCI */
-
-
-#define CONFIG_HWCONFIG 1
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-#define CONFIG_PHY_MODE_NEED_CHANGE
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9
-#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
-#endif
-
-#define CONFIG_UEC_ETH2 /* GETH2 */
-
-#ifdef CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
-#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC2_TX_CLK QE_CLK4
-#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR 1
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
- #define CONFIG_ENV_IS_IN_FLASH 1
- #define CONFIG_ENV_ADDR \
- (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
- #define CONFIG_ENV_SECT_SIZE 0x20000
- #define CONFIG_ENV_SIZE 0x2000
-#else
- #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
- #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
- #define CONFIG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_SDRAM
-
-#if defined(CONFIG_PCI)
- #define CONFIG_CMD_PCI
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT)
- #undef CONFIG_CMD_SAVEENV
- #undef CONFIG_CMD_LOADS
-#endif
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
- /* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
- /* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
-
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2 HID2_HBE
-
-/*
- * MMU Setup
- */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-#define CONFIG_BAT_RW
-
-/* DDR/LBC SDRAM: cacheable */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \
- | BATU_BL_4M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-
-/* BCSR: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR \
- | BATU_BL_128K \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \
- | BATU_BL_32M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/* DDR/LBC SDRAM next 256M: cacheable */
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM_BASE2 \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM_BASE2 \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \
- | BATU_BL_128K \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-
-#ifdef CONFIG_PCI
-/* PCI MEM space: cacheable */
-#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-/* PCI MMIO space: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-#else
-#define CONFIG_SYS_IBAT6L (0)
-#define CONFIG_SYS_IBAT6U (0)
-#define CONFIG_SYS_IBAT7L (0)
-#define CONFIG_SYS_IBAT7U (0)
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#define CONFIG_ENV_OVERWRITE
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
-
-#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=1000000\0" \
- "ramdiskfile=ramfs.83xx\0" \
- "fdtaddr=780000\0" \
- "fdtfile=mpc836x_mds.dtb\0" \
- ""
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
- "$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * Copyright (C) 2006 Freescale Semiconductor, Inc.
- * Dave Liu <daveliu@freescale.com>
- *
- * Copyright (C) 2007 Logic Product Development, Inc.
- * Peter Barada <peterb@logicpd.com>
- *
- * Copyright (C) 2007 MontaVista Software, Inc.
- * Anton Vorontsov <avorontsov@ru.mvista.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300 1 /* E300 family */
-#define CONFIG_QE 1 /* Has QE */
-#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
-#define CONFIG_MPC8360ERDK 1 /* MPC8360ERDK board specific */
-
-#define CONFIG_SYS_TEXT_BASE 0xFF800000
-
-/*
- * System Clock Setup
- */
-#ifdef CONFIG_CLKIN_33MHZ
-#define CONFIG_83XX_CLKIN 33333333
-#define CONFIG_SYS_CLK_FREQ 33333333
-#define CONFIG_PCI_33M 1
-#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_10X1
-#else
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_PCI_66M 1
-#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_5X1
-#endif /* CONFIG_CLKIN_33MHZ */
-
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
- HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
- HRCWL_DDR_TO_SCB_CLK_1X1 |\
- HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\
- HRCWL_CORE_TO_CSB_2X1 |\
- HRCWL_CE_TO_PLL_1X15)
-
-#define CONFIG_SYS_HRCW_HIGH (\
- HRCWH_PCI_HOST |\
- HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_PCICKDRV_ENABLE |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0X00000100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_16BIT |\
- HRCWH_SECONDARY_DDR_DISABLE |\
- HRCWH_BIG_ENDIAN |\
- HRCWH_LALE_EARLY)
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH 0x00000000
-#define CONFIG_SYS_SICRL 0x40000000
-
-#define CONFIG_BOARD_EARLY_INIT_R
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR 0xE0000000
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
- | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CONFIG_SYS_83XX_DDR_USES_CS0
-
-#define CONFIG_DDR_ECC /* support DDR ECC function */
-#define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
-
-/*
- * DDRCDR - DDR Control Driver Register
- */
-#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \
- | DDRCDR_ODT \
- | DDRCDR_Q_DRN)
- /* 0x80080001 */
-
-#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 256 /* MB */
-#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
- | CSCONFIG_ROW_BIT_13 \
- | CSCONFIG_COL_BIT_10 \
- | CSCONFIG_ODT_WR_ONLY_CURRENT)
-#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 \
- | SDRAM_CFG_ECC_EN)
-#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000
-#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL ((256 << SDRAM_INTERVAL_BSTOPRE_SHIFT) \
- | (1115 << SDRAM_INTERVAL_REFINT_SHIFT))
-#define CONFIG_SYS_DDR_MODE 0x47800432
-#define CONFIG_SYS_DDR_MODE2 0x8000c000
-
-#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
- (9 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
- (3 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
- (3 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
- (0 << TIMING_CFG0_WWT_SHIFT) | \
- (0 << TIMING_CFG0_RRT_SHIFT) | \
- (0 << TIMING_CFG0_WRT_SHIFT) | \
- (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_30) | \
- (2 << TIMING_CFG1_WRTORD_SHIFT) | \
- (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
- (3 << TIMING_CFG1_WRREC_SHIFT) | \
- (10 << TIMING_CFG1_REFREC_SHIFT) | \
- (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
- (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
- (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2 ((9 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
- (4 << TIMING_CFG2_CKE_PLS_SHIFT) | \
- (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
- (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
- (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
- (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
- (0 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-
-/*
- * Memory test
- */
-#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
-#define CONFIG_SYS_MEMTEST_END 0x00100000
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* FLASH base address */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
-#define CONFIG_SYS_LBC_LBCR 0x00000000
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
-#define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use intel Flash protection. */
-
- /* Window base at flash base */
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB)
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
- | BR_PS_16 /* 16 bit port */ \
- | BR_MS_GPCM /* MSEL = GPCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
- | OR_UPM_XAM \
- | OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV2 \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-
-/*
- * NAND flash on the local bus
- */
-#define CONFIG_SYS_NAND_BASE 0x60000000
-#define CONFIG_CMD_NAND 1
-#define CONFIG_NAND_FSL_UPM 1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
-/*
- * [RFC] Comment said 4KB window; code said 256MB window; OR1 says 64MB
- * ... What's correct?
- */
-#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_256MB)
-
-/* Port size 8 bit, UPMA */
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE \
- | BR_PS_8 \
- | BR_MS_UPMA \
- | BR_V)
- /* 0x60000881 */
-#define CONFIG_SYS_OR1_PRELIM (OR_AM_64MB | OR_UPM_EAD)
- /* 0xFC000001 */
-
-/*
- * Fujitsu MB86277 (MINT) graphics controller
- */
-#define CONFIG_SYS_VIDEO_BASE 0x70000000
-
-#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VIDEO_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
-
-/* Port size 32 bit, UPMB */
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VIDEO_BASE \
- | BR_PS_32 \
- | BR_MS_UPMB \
- | BR_V)
- /* 0x000018a1 */
-#define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB | OR_UPM_EAD)
- /* 0xFC000001 */
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} }
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_PCI
-
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
-#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE 0xE0300000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
-
-#endif /* CONFIG_PCI */
-
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9
-#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 2
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
-#endif
-
-#define CONFIG_UEC_ETH2 /* GETH2 */
-
-#ifdef CONFIG_UEC_ETH2
-#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
-#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC2_TX_CLK QE_CLK4
-#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
-#define CONFIG_SYS_UEC2_PHY_ADDR 4
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID
-#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#define CONFIG_ENV_SIZE 0x20000
-#else /* CONFIG_SYS_RAMBOOT */
-#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
-#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CONFIG_SYS_RAMBOOT */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#endif
-
-#if defined(CONFIG_SYS_RAMBOOT)
-#undef CONFIG_CMD_SAVEENV
-#undef CONFIG_CMD_LOADS
-#endif
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
-#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
- #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
- /* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
- /* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
-
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2 HID2_HBE
-
-/*
- * MMU Setup
- */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \
- | BATU_BL_4M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-
-/* NAND: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_NAND_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_NAND_BASE \
- | BATU_BL_64M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \
- | BATU_BL_32M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR \
- | BATL_PP_RW)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR \
- | BATU_BL_128K \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_VIDEO_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_VIDEO_BASE \
- | BATU_BL_64M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-
-#ifdef CONFIG_PCI
-/* PCI MEM space: cacheable */
-#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \
- | BATL_PP_RW \
- | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-/* PCI MMIO space: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-#else /* CONFIG_PCI */
-#define CONFIG_SYS_IBAT6L (0)
-#define CONFIG_SYS_IBAT6U (0)
-#define CONFIG_SYS_IBAT7L (0)
-#define CONFIG_SYS_IBAT7U (0)
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADADDR a00000
-#define CONFIG_HOSTNAME mpc8360erdk
-#define CONFIG_BOOTFILE "uImage"
-
-#define CONFIG_ROOTPATH "/nfsroot/"
-
-#define CONFIG_BOOTDELAY 2 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "loadaddr=a00000\0" \
- "fdtaddr=900000\0" \
- "fdtfile=mpc836x_rdk.dtb\0" \
- "fsfile=fs\0" \
- "ubootfile=u-boot.bin\0" \
- "mtdparts=mtdparts=60000000.nand-flash:4096k(kernel),128k(dtb),"\
- "-(rootfs)\0" \
- "setbootargs=setenv bootargs console=$consoledev,$baudrate " \
- "$mtdparts panic=1\0" \
- "adddhcpargs=setenv bootargs $bootargs ip=on\0" \
- "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:" \
- "$gatewayip:$netmask:$hostname:$netdev:off " \
- "root=/dev/nfs rw nfsroot=$serverip:$rootpath\0" \
- "addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 " \
- "rootfstype=jffs2 rw\0" \
- "tftp_get_uboot=tftp 100000 $ubootfile\0" \
- "tftp_get_kernel=tftp $loadaddr $bootfile\0" \
- "tftp_get_dtb=tftp $fdtaddr $fdtfile\0" \
- "tftp_get_fs=tftp c00000 $fsfile\0" \
- "nand_erase_kernel=nand erase 0 400000\0" \
- "nand_erase_dtb=nand erase 400000 20000\0" \
- "nand_erase_fs=nand erase 420000 3be0000\0" \
- "nand_write_kernel=nand write.jffs2 $loadaddr 0 400000\0" \
- "nand_write_dtb=nand write.jffs2 $fdtaddr 400000 20000\0" \
- "nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0" \
- "nand_read_kernel=nand read.jffs2 $loadaddr 0 400000\0" \
- "nand_read_dtb=nand read.jffs2 $fdtaddr 400000 20000\0" \
- "nor_reflash=protect off ff800000 ff87ffff ; " \
- "erase ff800000 ff87ffff ; " \
- "cp.b 100000 ff800000 $filesize\0" \
- "nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel " \
- "nand_write_kernel\0" \
- "nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\
- "nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0" \
- "nand_reflash=run nand_reflash_kernel nand_reflash_dtb " \
- "nand_reflash_fs\0" \
- "boot_m=bootm $loadaddr - $fdtaddr\0" \
- "dhcpboot=dhcp ; run setbootargs adddhcpargs tftp_get_dtb boot_m\0"\
- "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\
- "boot_m\0" \
- "nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\
- "boot_m\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run dhcpboot"
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff