wandboard: add Future Eletronics 7" WVGA LCD extension board

This adds support for the 7" WVGA produced by Future Eletronics and
make it dynamically detect if it is connected or not based on the
touchscreen controller.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>

diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
index f1951dc5ef0a3f0ed2e5c1b39de6b4c1331278a7..3c8b7a5d2d0a9278158a947f73b143d8713d5989 100644 (file)
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -1,5 +1,6 @@
 /*
  * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ * Copyright (C) 2014 O.S. Systems Software LTDA.
  *
  * Author: Fabio Estevam <fabio.estevam@freescale.com>
  *
@@ -15,18 +16,19 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/gpio.h>
 #include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
 #include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/video.h>
 #include <asm/io.h>
 #include <linux/sizes.h>
 #include <common.h>
 #include <fsl_esdhc.h>
-#include <ipu_pixfmt.h>
 #include <mmc.h>
 #include <miiphy.h>
 #include <netdev.h>
-#include <linux/fb.h>
 #include <phy.h>
 #include <input.h>
+#include <i2c.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -41,6 +43,10 @@ DECLARE_GLOBAL_DATA_PTR;
 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                  \
        PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
 
+#define I2C_PAD_CTRL   (PAD_CTL_PUS_100K_UP |                  \
+       PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |   \
+       PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
 #define USDHC1_CD_GPIO         IMX_GPIO_NR(1, 2)
 #define USDHC3_CD_GPIO         IMX_GPIO_NR(3, 9)
 #define ETH_PHY_RESET          IMX_GPIO_NR(3, 29)
@@ -210,38 +216,120 @@ int board_phy_config(struct phy_device *phydev)
 }
 
 #if defined(CONFIG_VIDEO_IPUV3)
-static struct fb_videomode const hdmi = {
-       .name           = "HDMI",
-       .refresh        = 60,
-       .xres           = 1024,
-       .yres           = 768,
-       .pixclock       = 15385,
-       .left_margin    = 220,
-       .right_margin   = 40,
-       .upper_margin   = 21,
-       .lower_margin   = 7,
-       .hsync_len      = 60,
-       .vsync_len      = 10,
-       .sync           = FB_SYNC_EXT,
-       .vmode          = FB_VMODE_NONINTERLACED
+struct i2c_pads_info i2c2_pad_info = {
+       .scl = {
+               .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL
+                       | MUX_PAD_CTRL(I2C_PAD_CTRL),
+               .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12
+                       | MUX_PAD_CTRL(I2C_PAD_CTRL),
+               .gp = IMX_GPIO_NR(4, 12)
+       },
+       .sda = {
+               .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA
+                       | MUX_PAD_CTRL(I2C_PAD_CTRL),
+               .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13
+                       | MUX_PAD_CTRL(I2C_PAD_CTRL),
+               .gp = IMX_GPIO_NR(4, 13)
+       }
 };
 
-int board_video_skip(void)
-{
-       int ret;
+static iomux_v3_cfg_t const fwadapt_7wvga_pads[] = {
+       MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK,
+       MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02, /* HSync */
+       MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03, /* VSync */
+       MX6_PAD_DI0_PIN4__IPU1_DI0_PIN04
+               | MUX_PAD_CTRL(PAD_CTL_DSE_120ohm), /* Contrast */
+       MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15, /* DISP0_DRDY */
+
+       MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
+       MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
+       MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
+       MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
+       MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
+       MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
+       MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
+       MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
+       MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
+       MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
+       MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
+       MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
+       MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
+       MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
+       MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
+       MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
+       MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
+       MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
+
+       MX6_PAD_SD4_DAT2__GPIO2_IO10
+               | MUX_PAD_CTRL(NO_PAD_CTRL), /* DISP0_BKLEN */
+       MX6_PAD_SD4_DAT3__GPIO2_IO11
+               | MUX_PAD_CTRL(NO_PAD_CTRL), /* DISP0_VDDEN */
+};
 
-       ret = ipuv3_fb_init(&hdmi, 0, IPU_PIX_FMT_RGB24);
+static void do_enable_hdmi(struct display_info_t const *dev)
+{
+       imx_enable_hdmi_phy();
+}
 
-       if (ret) {
-               printf("HDMI cannot be configured: %d\n", ret);
-               return ret;
-       }
+static int detect_i2c(struct display_info_t const *dev)
+{
+       return (0 == i2c_set_bus_num(dev->bus)) &&
+                       (0 == i2c_probe(dev->addr));
+}
 
-       imx_enable_hdmi_phy();
+static void enable_fwadapt_7wvga(struct display_info_t const *dev)
+{
+       imx_iomux_v3_setup_multiple_pads(
+               fwadapt_7wvga_pads,
+               ARRAY_SIZE(fwadapt_7wvga_pads));
 
-       return ret;
+       gpio_direction_output(IMX_GPIO_NR(2, 10), 1);
+       gpio_direction_output(IMX_GPIO_NR(2, 11), 1);
 }
 
+struct display_info_t const displays[] = {{
+       .bus    = -1,
+       .addr   = 0,
+       .pixfmt = IPU_PIX_FMT_RGB24,
+       .detect = detect_hdmi,
+       .enable = do_enable_hdmi,
+       .mode   = {
+               .name           = "HDMI",
+               .refresh        = 60,
+               .xres           = 1024,
+               .yres           = 768,
+               .pixclock       = 15385,
+               .left_margin    = 220,
+               .right_margin   = 40,
+               .upper_margin   = 21,
+               .lower_margin   = 7,
+               .hsync_len      = 60,
+               .vsync_len      = 10,
+               .sync           = FB_SYNC_EXT,
+               .vmode          = FB_VMODE_NONINTERLACED
+} }, {
+       .bus    = 1,
+       .addr   = 0x10,
+       .pixfmt = IPU_PIX_FMT_RGB666,
+       .detect = detect_i2c,
+       .enable = enable_fwadapt_7wvga,
+       .mode   = {
+               .name           = "FWBADAPT-LCD-F07A-0102",
+               .refresh        = 60,
+               .xres           = 800,
+               .yres           = 480,
+               .pixclock       = 33260,
+               .left_margin    = 128,
+               .right_margin   = 128,
+               .upper_margin   = 22,
+               .lower_margin   = 22,
+               .hsync_len      = 1,
+               .vsync_len      = 1,
+               .sync           = 0,
+               .vmode          = FB_VMODE_NONINTERLACED
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+
 static void setup_display(void)
 {
        struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
@@ -254,6 +342,10 @@ static void setup_display(void)
        reg |= (CHSCCDR_CLK_SEL_LDB_DI0
                << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
        writel(reg, &mxc_ccm->chsccdr);
+
+       /* Disable LCD backlight */
+       imx_iomux_v3_setup_pad(MX6_PAD_DI0_PIN4__GPIO4_IO20);
+       gpio_direction_input(IMX_GPIO_NR(4, 20));
 }
 #endif /* CONFIG_VIDEO_IPUV3 */
 
@@ -305,6 +397,8 @@ int board_init(void)
        /* address of boot parameters */
        gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 
+       setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c2_pad_info);
+
        return 0;
 }
 

diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h
index b137d06e205d464371631d521ddb74305164484c..584fc9ecce19763786fb7d02c75ee5621d5dcc68 100644 (file)
--- a/include/configs/wandboard.h
+++ b/include/configs/wandboard.h
@@ -58,6 +58,12 @@
 #define CONFIG_LOADADDR                        0x12000000
 #define CONFIG_SYS_TEXT_BASE           0x17800000
 
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED           100000
+
 /* MMC Configuration */
 #define CONFIG_FSL_ESDHC
 #define CONFIG_FSL_USDHC
@@ -101,6 +107,7 @@
 #define CONFIG_VIDEO_BMP_LOGO
 #define CONFIG_IPUV3_CLK 260000000
 #define CONFIG_IMX_HDMI
+#define CONFIG_IMX_VIDEO_SKIP
 
 #if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
 #define CONFIG_DEFAULT_FDT_FILE                "imx6dl-wandboard.dtb"