/* check a device connected to root_hub */
if ((parent && parent->devnum == 1) ||
- (dev->devnum == 1))
+ dev->devnum == 1)
return;
*hub_devnum = (u8)parent->devnum;
}
static void set_devadd(struct r8a66597 *r8a66597, u8 r8a66597_address,
- struct usb_device *dev, int port)
+ struct usb_device *dev, int port)
{
u16 val, usbspd, upphub, hubport;
unsigned long devadd_reg = get_devadd_addr(r8a66597_address);
R8A66597_DPRINT("%s\n", __func__);
r8a66597_mdfy(r8a66597, MBW | BULK_OUT_PIPENUM,
- MBW | CURPIPE, CFIFOSEL);
+ MBW | CURPIPE, CFIFOSEL);
r8a66597_reg_wait(r8a66597, CFIFOSEL, CURPIPE, BULK_OUT_PIPENUM);
tmp = r8a66597_read(r8a66597, CFIFOCTR);
if ((tmp & FRDY) == 0) {
dev->act_len += size;
r8a66597_mdfy(r8a66597, PID_BUF, PID,
- get_pipectr_addr(BULK_OUT_PIPENUM));
+ get_pipectr_addr(BULK_OUT_PIPENUM));
while (!(r8a66597_read(r8a66597, BEMPSTS) & (1 << BULK_OUT_PIPENUM)))
if (ctrlc())
if (dev->act_len >= transfer_len)
r8a66597_mdfy(r8a66597, PID_NAK, PID,
- get_pipectr_addr(BULK_OUT_PIPENUM));
+ get_pipectr_addr(BULK_OUT_PIPENUM));
return 0;
}
/* prepare */
if (dev->act_len == 0) {
r8a66597_mdfy(r8a66597, PID_NAK, PID,
- get_pipectr_addr(pipenum));
+ get_pipectr_addr(pipenum));
r8a66597_write(r8a66597, ~(1 << pipenum), BRDYSTS);
r8a66597_write(r8a66597, TRCLR, get_pipetre_addr(pipenum));
r8a66597_write(r8a66597,
- (transfer_len + maxpacket - 1) / maxpacket,
+ (transfer_len + maxpacket - 1) / maxpacket,
get_pipetrn_addr(pipenum));
r8a66597_bset(r8a66597, TRENB, get_pipetre_addr(pipenum));
r8a66597_mdfy(r8a66597, PID_BUF, PID,
- get_pipectr_addr(pipenum));
+ get_pipectr_addr(pipenum));
}
r8a66597_mdfy(r8a66597, MBW | pipenum, MBW | CURPIPE, CFIFOSEL);
}
static int send_status_packet(struct r8a66597 *r8a66597,
- unsigned long pipe)
+ unsigned long pipe)
{
r8a66597_bset(r8a66597, SQSET, DCPCTR);
r8a66597_mdfy(r8a66597, PID_NAK, PID, DCPCTR);
return -1; /* fail */
}
-/*-------------------------------------------------------------------------*
- * Virtual Root Hub
- *-------------------------------------------------------------------------*/
+/* Virtual Root Hub */
#include <usbroothubdes.h>
switch ((wValue & 0xff00) >> 8) {
case (0x01): /* device descriptor */
len = min_t(unsigned int,
- leni,
+ leni,
min_t(unsigned int,
- sizeof(root_hub_dev_des),
+ sizeof(root_hub_dev_des),
wLength));
memcpy(buffer, root_hub_dev_des, len);
break;
case (0x02): /* configuration descriptor */
len = min_t(unsigned int,
- leni,
+ leni,
min_t(unsigned int,
- sizeof(root_hub_config_des),
+ sizeof(root_hub_config_des),
wLength));
memcpy(buffer, root_hub_config_des, len);
break;
case (0x03): /* string descriptors */
if (wValue == 0x0300) {
len = min_t(unsigned int,
- leni,
+ leni,
min_t(unsigned int,
- sizeof(root_hub_str_index0),
+ sizeof(root_hub_str_index0),
wLength));
memcpy(buffer, root_hub_str_index0, len);
}
if (wValue == 0x0301) {
len = min_t(unsigned int,
- leni,
+ leni,
min_t(unsigned int,
- sizeof(root_hub_str_index1),
+ sizeof(root_hub_str_index1),
wLength));
memcpy(buffer, root_hub_str_index1, len);
}
} else {
data[0] += 2;
data[8] = (temp & RH_B_DR) >> 8;
- data[10] = data[9] = 0xff;
+ data[9] = 0xff;
+ data[10] = 0xff;
}
len = min_t(unsigned int, leni,
}
case RH_GET_CONFIGURATION:
- *(__u8 *) buffer = 0x01;
+ *(__u8 *)buffer = 0x01;
len = 1;
break;
case RH_SET_CONFIGURATION:
return stat;
}
-static int r8a66597_submit_control_msg(struct udevice *udev, struct usb_device *dev,
- unsigned long pipe, void *buffer, int length,
- struct devrequest *setup)
+static int r8a66597_submit_control_msg(struct udevice *udev,
+ struct usb_device *dev,
+ unsigned long pipe, void *buffer,
+ int length, struct devrequest *setup)
{
struct r8a66597 *r8a66597 = dev_get_priv(udev);
u16 r8a66597_address = setup->request == USB_REQ_SET_ADDRESS ?
dev->act_len = 0;
if (usb_pipein(pipe))
if (receive_control_packet(r8a66597, dev, buffer,
- length) < 0)
+ length) < 0)
return -1;
if (send_status_packet(r8a66597, pipe) < 0)
return 0;
}
-static int r8a66597_submit_bulk_msg(struct udevice *udev, struct usb_device *dev,
- unsigned long pipe, void *buffer, int length)
+static int r8a66597_submit_bulk_msg(struct udevice *udev,
+ struct usb_device *dev, unsigned long pipe,
+ void *buffer, int length)
{
struct r8a66597 *r8a66597 = dev_get_priv(udev);
int ret = 0;
if (usb_pipein(pipe))
ret = receive_bulk_packet(r8a66597, dev, pipe, buffer,
- length);
+ length);
else
ret = send_bulk_packet(r8a66597, dev, pipe, buffer,
- length);
+ length);
}
if (ret == 0)
mdelay(100);
enable_controller(priv);
- r8a66597_port_power(priv, 0 , 1);
+ r8a66597_port_power(priv, 0, 1);
/* check usb device */
check_usb_device_connecting(priv);
#define PIPE3TRE 0x98
#define PIPE3TRN 0x9A
#define PIPE4TRE 0x9C
-#define PIPE4TRN 0x9E
-#define PIPE5TRE 0xA0
-#define PIPE5TRN 0xA2
+#define PIPE4TRN 0x9E
+#define PIPE5TRE 0xA0
+#define PIPE5TRN 0xA2
#define DEVADD0 0xD0
#define DEVADD1 0xD2
#define DEVADD2 0xD4
#define SUSPMODE0 0x102 /* RZ/A only */
/* System Configuration Control Register */
-#define HSE 0x0080 /* b7: Hi-speed enable */
-#define DCFM 0x0040 /* b6: Controller function select */
-#define DRPD 0x0020 /* b5: D+/- pull down control */
-#define DPRPU 0x0010 /* b4: D+ pull up control */
-#define XTAL 0x0004 /* b2: Crystal selection */
-#define XTAL12 0x0004 /* 12MHz */
-#define XTAL48 0x0000 /* 48MHz */
-#define UPLLE 0x0002 /* b1: internal PLL control */
-#define USBE 0x0001 /* b0: USB module operation enable */
+#define HSE 0x0080 /* b7: Hi-speed enable */
+#define DCFM 0x0040 /* b6: Controller function select */
+#define DRPD 0x0020 /* b5: D+/- pull down control */
+#define DPRPU 0x0010 /* b4: D+ pull up control */
+#define XTAL 0x0004 /* b2: Crystal selection */
+#define XTAL12 0x0004 /* 12MHz */
+#define XTAL48 0x0000 /* 48MHz */
+#define UPLLE 0x0002 /* b1: internal PLL control */
+#define USBE 0x0001 /* b0: USB module operation enable */
/* System Configuration Status Register */
-#define OVCBIT 0x8000 /* b15-14: Over-current bit */
-#define OVCMON 0xC000 /* b15-14: Over-current monitor */
-#define SOFEA 0x0020 /* b5: SOF monitor */
-#define IDMON 0x0004 /* b3: ID-pin monitor */
-#define LNST 0x0003 /* b1-0: D+, D- line status */
-#define SE1 0x0003 /* SE1 */
-#define FS_KSTS 0x0002 /* Full-Speed K State */
-#define FS_JSTS 0x0001 /* Full-Speed J State */
-#define LS_JSTS 0x0002 /* Low-Speed J State */
-#define LS_KSTS 0x0001 /* Low-Speed K State */
-#define SE0 0x0000 /* SE0 */
+#define OVCBIT 0x8000 /* b15-14: Over-current bit */
+#define OVCMON 0xC000 /* b15-14: Over-current monitor */
+#define SOFEA 0x0020 /* b5: SOF monitor */
+#define IDMON 0x0004 /* b3: ID-pin monitor */
+#define LNST 0x0003 /* b1-0: D+, D- line status */
+#define SE1 0x0003 /* SE1 */
+#define FS_KSTS 0x0002 /* Full-Speed K State */
+#define FS_JSTS 0x0001 /* Full-Speed J State */
+#define LS_JSTS 0x0002 /* Low-Speed J State */
+#define LS_KSTS 0x0001 /* Low-Speed K State */
+#define SE0 0x0000 /* SE0 */
/* Device State Control Register */
-#define EXTLP0 0x0400 /* b10: External port */
-#define VBOUT 0x0200 /* b9: VBUS output */
-#define WKUP 0x0100 /* b8: Remote wakeup */
-#define RWUPE 0x0080 /* b7: Remote wakeup sense */
-#define USBRST 0x0040 /* b6: USB reset enable */
-#define RESUME 0x0020 /* b5: Resume enable */
-#define UACT 0x0010 /* b4: USB bus enable */
-#define RHST 0x0007 /* b1-0: Reset handshake status */
-#define HSPROC 0x0004 /* HS handshake is processing */
-#define HSMODE 0x0003 /* Hi-Speed mode */
-#define FSMODE 0x0002 /* Full-Speed mode */
-#define LSMODE 0x0001 /* Low-Speed mode */
-#define UNDECID 0x0000 /* Undecided */
+#define EXTLP0 0x0400 /* b10: External port */
+#define VBOUT 0x0200 /* b9: VBUS output */
+#define WKUP 0x0100 /* b8: Remote wakeup */
+#define RWUPE 0x0080 /* b7: Remote wakeup sense */
+#define USBRST 0x0040 /* b6: USB reset enable */
+#define RESUME 0x0020 /* b5: Resume enable */
+#define UACT 0x0010 /* b4: USB bus enable */
+#define RHST 0x0007 /* b1-0: Reset handshake status */
+#define HSPROC 0x0004 /* HS handshake is processing */
+#define HSMODE 0x0003 /* Hi-Speed mode */
+#define FSMODE 0x0002 /* Full-Speed mode */
+#define LSMODE 0x0001 /* Low-Speed mode */
+#define UNDECID 0x0000 /* Undecided */
/* Test Mode Register */
-#define UTST 0x000F /* b3-0: Test select */
-#define H_TST_PACKET 0x000C /* HOST TEST Packet */
-#define H_TST_SE0_NAK 0x000B /* HOST TEST SE0 NAK */
-#define H_TST_K 0x000A /* HOST TEST K */
-#define H_TST_J 0x0009 /* HOST TEST J */
-#define H_TST_NORMAL 0x0000 /* HOST Normal Mode */
-#define P_TST_PACKET 0x0004 /* PERI TEST Packet */
-#define P_TST_SE0_NAK 0x0003 /* PERI TEST SE0 NAK */
-#define P_TST_K 0x0002 /* PERI TEST K */
-#define P_TST_J 0x0001 /* PERI TEST J */
-#define P_TST_NORMAL 0x0000 /* PERI Normal Mode */
+#define UTST 0x000F /* b3-0: Test select */
+#define H_TST_PACKET 0x000C /* HOST TEST Packet */
+#define H_TST_SE0_NAK 0x000B /* HOST TEST SE0 NAK */
+#define H_TST_K 0x000A /* HOST TEST K */
+#define H_TST_J 0x0009 /* HOST TEST J */
+#define H_TST_NORMAL 0x0000 /* HOST Normal Mode */
+#define P_TST_PACKET 0x0004 /* PERI TEST Packet */
+#define P_TST_SE0_NAK 0x0003 /* PERI TEST SE0 NAK */
+#define P_TST_K 0x0002 /* PERI TEST K */
+#define P_TST_J 0x0001 /* PERI TEST J */
+#define P_TST_NORMAL 0x0000 /* PERI Normal Mode */
/* Data Pin Configuration Register */
-#define LDRV 0x8000 /* b15: Drive Current Adjust */
-#define VIF1 0x0000 /* VIF = 1.8V */
-#define VIF3 0x8000 /* VIF = 3.3V */
-#define INTA 0x0001 /* b1: USB INT-pin active */
+#define LDRV 0x8000 /* b15: Drive Current Adjust */
+#define VIF1 0x0000 /* VIF = 1.8V */
+#define VIF3 0x8000 /* VIF = 3.3V */
+#define INTA 0x0001 /* b1: USB INT-pin active */
/* DMAx Pin Configuration Register */
-#define DREQA 0x4000 /* b14: Dreq active select */
-#define BURST 0x2000 /* b13: Burst mode */
-#define DACKA 0x0400 /* b10: Dack active select */
-#define DFORM 0x0380 /* b9-7: DMA mode select */
-#define CPU_ADR_RD_WR 0x0000 /* Address + RD/WR mode (CPU bus) */
-#define CPU_DACK_RD_WR 0x0100 /* DACK + RD/WR mode (CPU bus) */
-#define CPU_DACK_ONLY 0x0180 /* DACK only mode (CPU bus) */
-#define SPLIT_DACK_ONLY 0x0200 /* DACK only mode (SPLIT bus) */
-#define DENDA 0x0040 /* b6: Dend active select */
-#define PKTM 0x0020 /* b5: Packet mode */
-#define DENDE 0x0010 /* b4: Dend enable */
-#define OBUS 0x0004 /* b2: OUTbus mode */
+#define DREQA 0x4000 /* b14: Dreq active select */
+#define BURST 0x2000 /* b13: Burst mode */
+#define DACKA 0x0400 /* b10: Dack active select */
+#define DFORM 0x0380 /* b9-7: DMA mode select */
+#define CPU_ADR_RD_WR 0x0000 /* Address + RD/WR mode (CPU bus) */
+#define CPU_DACK_RD_WR 0x0100 /* DACK + RD/WR mode (CPU bus) */
+#define CPU_DACK_ONLY 0x0180 /* DACK only mode (CPU bus) */
+#define SPLIT_DACK_ONLY 0x0200 /* DACK only mode (SPLIT bus) */
+#define DENDA 0x0040 /* b6: Dend active select */
+#define PKTM 0x0020 /* b5: Packet mode */
+#define DENDE 0x0010 /* b4: Dend enable */
+#define OBUS 0x0004 /* b2: OUTbus mode */
/* CFIFO/DxFIFO Port Select Register */
-#define RCNT 0x8000 /* b15: Read count mode */
-#define REW 0x4000 /* b14: Buffer rewind */
-#define DCLRM 0x2000 /* b13: DMA buffer clear mode */
-#define DREQE 0x1000 /* b12: DREQ output enable */
-#define MBW 0x0800 /* b10: Maximum bit width for FIFO access */
-#define MBW_8 0x0000 /* 8bit */
-#define MBW_16 0x0400 /* 16bit */
-#define MBW_32 0x0800 /* 32bit */
-#define BIGEND 0x0100 /* b8: Big endian mode */
-#define BYTE_LITTLE 0x0000 /* little dendian */
-#define BYTE_BIG 0x0100 /* big endifan */
-#define ISEL 0x0020 /* b5: DCP FIFO port direction select */
-#define CURPIPE 0x000F /* b2-0: PIPE select */
+#define RCNT 0x8000 /* b15: Read count mode */
+#define REW 0x4000 /* b14: Buffer rewind */
+#define DCLRM 0x2000 /* b13: DMA buffer clear mode */
+#define DREQE 0x1000 /* b12: DREQ output enable */
+#define MBW 0x0800 /* b10: Maximum bit width for FIFO access */
+#define MBW_8 0x0000 /* 8bit */
+#define MBW_16 0x0400 /* 16bit */
+#define MBW_32 0x0800 /* 32bit */
+#define BIGEND 0x0100 /* b8: Big endian mode */
+#define BYTE_LITTLE 0x0000 /* little dendian */
+#define BYTE_BIG 0x0100 /* big endifan */
+#define ISEL 0x0020 /* b5: DCP FIFO port direction select */
+#define CURPIPE 0x000F /* b2-0: PIPE select */
/* CFIFO/DxFIFO Port Control Register */
-#define BVAL 0x8000 /* b15: Buffer valid flag */
-#define BCLR 0x4000 /* b14: Buffer clear */
-#define FRDY 0x2000 /* b13: FIFO ready */
-#define DTLN 0x0FFF /* b11-0: FIFO received data length */
+#define BVAL 0x8000 /* b15: Buffer valid flag */
+#define BCLR 0x4000 /* b14: Buffer clear */
+#define FRDY 0x2000 /* b13: FIFO ready */
+#define DTLN 0x0FFF /* b11-0: FIFO received data length */
/* Interrupt Enable Register 0 */
-#define VBSE 0x8000 /* b15: VBUS interrupt */
-#define RSME 0x4000 /* b14: Resume interrupt */
-#define SOFE 0x2000 /* b13: Frame update interrupt */
-#define DVSE 0x1000 /* b12: Device state transition interrupt */
-#define CTRE 0x0800 /* b11: Control transfer stage transition interrupt */
-#define BEMPE 0x0400 /* b10: Buffer empty interrupt */
-#define NRDYE 0x0200 /* b9: Buffer not ready interrupt */
-#define BRDYE 0x0100 /* b8: Buffer ready interrupt */
+#define VBSE 0x8000 /* b15: VBUS interrupt */
+#define RSME 0x4000 /* b14: Resume interrupt */
+#define SOFE 0x2000 /* b13: Frame update interrupt */
+#define DVSE 0x1000 /* b12: Device state transition interrupt */
+#define CTRE 0x0800 /* b11: Control transfer stage transition interrupt */
+#define BEMPE 0x0400 /* b10: Buffer empty interrupt */
+#define NRDYE 0x0200 /* b9: Buffer not ready interrupt */
+#define BRDYE 0x0100 /* b8: Buffer ready interrupt */
/* Interrupt Enable Register 1 */
-#define OVRCRE 0x8000 /* b15: Over-current interrupt */
-#define BCHGE 0x4000 /* b14: USB us chenge interrupt */
-#define DTCHE 0x1000 /* b12: Detach sense interrupt */
-#define ATTCHE 0x0800 /* b11: Attach sense interrupt */
-#define EOFERRE 0x0040 /* b6: EOF error interrupt */
-#define SIGNE 0x0020 /* b5: SETUP IGNORE interrupt */
-#define SACKE 0x0010 /* b4: SETUP ACK interrupt */
+#define OVRCRE 0x8000 /* b15: Over-current interrupt */
+#define BCHGE 0x4000 /* b14: USB us chenge interrupt */
+#define DTCHE 0x1000 /* b12: Detach sense interrupt */
+#define ATTCHE 0x0800 /* b11: Attach sense interrupt */
+#define EOFERRE 0x0040 /* b6: EOF error interrupt */
+#define SIGNE 0x0020 /* b5: SETUP IGNORE interrupt */
+#define SACKE 0x0010 /* b4: SETUP ACK interrupt */
/* BRDY Interrupt Enable/Status Register */
-#define BRDY9 0x0200 /* b9: PIPE9 */
-#define BRDY8 0x0100 /* b8: PIPE8 */
-#define BRDY7 0x0080 /* b7: PIPE7 */
-#define BRDY6 0x0040 /* b6: PIPE6 */
-#define BRDY5 0x0020 /* b5: PIPE5 */
-#define BRDY4 0x0010 /* b4: PIPE4 */
-#define BRDY3 0x0008 /* b3: PIPE3 */
-#define BRDY2 0x0004 /* b2: PIPE2 */
-#define BRDY1 0x0002 /* b1: PIPE1 */
-#define BRDY0 0x0001 /* b1: PIPE0 */
+#define BRDY9 0x0200 /* b9: PIPE9 */
+#define BRDY8 0x0100 /* b8: PIPE8 */
+#define BRDY7 0x0080 /* b7: PIPE7 */
+#define BRDY6 0x0040 /* b6: PIPE6 */
+#define BRDY5 0x0020 /* b5: PIPE5 */
+#define BRDY4 0x0010 /* b4: PIPE4 */
+#define BRDY3 0x0008 /* b3: PIPE3 */
+#define BRDY2 0x0004 /* b2: PIPE2 */
+#define BRDY1 0x0002 /* b1: PIPE1 */
+#define BRDY0 0x0001 /* b1: PIPE0 */
/* NRDY Interrupt Enable/Status Register */
-#define NRDY9 0x0200 /* b9: PIPE9 */
-#define NRDY8 0x0100 /* b8: PIPE8 */
-#define NRDY7 0x0080 /* b7: PIPE7 */
-#define NRDY6 0x0040 /* b6: PIPE6 */
-#define NRDY5 0x0020 /* b5: PIPE5 */
-#define NRDY4 0x0010 /* b4: PIPE4 */
-#define NRDY3 0x0008 /* b3: PIPE3 */
-#define NRDY2 0x0004 /* b2: PIPE2 */
-#define NRDY1 0x0002 /* b1: PIPE1 */
-#define NRDY0 0x0001 /* b1: PIPE0 */
+#define NRDY9 0x0200 /* b9: PIPE9 */
+#define NRDY8 0x0100 /* b8: PIPE8 */
+#define NRDY7 0x0080 /* b7: PIPE7 */
+#define NRDY6 0x0040 /* b6: PIPE6 */
+#define NRDY5 0x0020 /* b5: PIPE5 */
+#define NRDY4 0x0010 /* b4: PIPE4 */
+#define NRDY3 0x0008 /* b3: PIPE3 */
+#define NRDY2 0x0004 /* b2: PIPE2 */
+#define NRDY1 0x0002 /* b1: PIPE1 */
+#define NRDY0 0x0001 /* b1: PIPE0 */
/* BEMP Interrupt Enable/Status Register */
-#define BEMP9 0x0200 /* b9: PIPE9 */
-#define BEMP8 0x0100 /* b8: PIPE8 */
-#define BEMP7 0x0080 /* b7: PIPE7 */
-#define BEMP6 0x0040 /* b6: PIPE6 */
-#define BEMP5 0x0020 /* b5: PIPE5 */
-#define BEMP4 0x0010 /* b4: PIPE4 */
-#define BEMP3 0x0008 /* b3: PIPE3 */
-#define BEMP2 0x0004 /* b2: PIPE2 */
-#define BEMP1 0x0002 /* b1: PIPE1 */
-#define BEMP0 0x0001 /* b0: PIPE0 */
+#define BEMP9 0x0200 /* b9: PIPE9 */
+#define BEMP8 0x0100 /* b8: PIPE8 */
+#define BEMP7 0x0080 /* b7: PIPE7 */
+#define BEMP6 0x0040 /* b6: PIPE6 */
+#define BEMP5 0x0020 /* b5: PIPE5 */
+#define BEMP4 0x0010 /* b4: PIPE4 */
+#define BEMP3 0x0008 /* b3: PIPE3 */
+#define BEMP2 0x0004 /* b2: PIPE2 */
+#define BEMP1 0x0002 /* b1: PIPE1 */
+#define BEMP0 0x0001 /* b0: PIPE0 */
/* SOF Pin Configuration Register */
-#define TRNENSEL 0x0100 /* b8: Select transaction enable period */
-#define BRDYM 0x0040 /* b6: BRDY clear timing */
-#define INTL 0x0020 /* b5: Interrupt sense select */
-#define EDGESTS 0x0010 /* b4: */
-#define SOFMODE 0x000C /* b3-2: SOF pin select */
-#define SOF_125US 0x0008 /* SOF OUT 125us Frame Signal */
-#define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */
-#define SOF_DISABLE 0x0000 /* SOF OUT Disable */
+#define TRNENSEL 0x0100 /* b8: Select transaction enable period */
+#define BRDYM 0x0040 /* b6: BRDY clear timing */
+#define INTL 0x0020 /* b5: Interrupt sense select */
+#define EDGESTS 0x0010 /* b4: */
+#define SOFMODE 0x000C /* b3-2: SOF pin select */
+#define SOF_125US 0x0008 /* SOF OUT 125us Frame Signal */
+#define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */
+#define SOF_DISABLE 0x0000 /* SOF OUT Disable */
/* Interrupt Status Register 0 */
-#define VBINT 0x8000 /* b15: VBUS interrupt */
-#define RESM 0x4000 /* b14: Resume interrupt */
-#define SOFR 0x2000 /* b13: SOF frame update interrupt */
-#define DVST 0x1000 /* b12: Device state transition interrupt */
-#define CTRT 0x0800 /* b11: Control transfer stage transition interrupt */
-#define BEMP 0x0400 /* b10: Buffer empty interrupt */
-#define NRDY 0x0200 /* b9: Buffer not ready interrupt */
-#define BRDY 0x0100 /* b8: Buffer ready interrupt */
-#define VBSTS 0x0080 /* b7: VBUS input port */
-#define DVSQ 0x0070 /* b6-4: Device state */
-#define DS_SPD_CNFG 0x0070 /* Suspend Configured */
-#define DS_SPD_ADDR 0x0060 /* Suspend Address */
-#define DS_SPD_DFLT 0x0050 /* Suspend Default */
-#define DS_SPD_POWR 0x0040 /* Suspend Powered */
-#define DS_SUSP 0x0040 /* Suspend */
-#define DS_CNFG 0x0030 /* Configured */
-#define DS_ADDS 0x0020 /* Address */
-#define DS_DFLT 0x0010 /* Default */
-#define DS_POWR 0x0000 /* Powered */
-#define DVSQS 0x0030 /* b5-4: Device state */
-#define VALID 0x0008 /* b3: Setup packet detected flag */
-#define CTSQ 0x0007 /* b2-0: Control transfer stage */
-#define CS_SQER 0x0006 /* Sequence error */
-#define CS_WRND 0x0005 /* Control write nodata status stage */
-#define CS_WRSS 0x0004 /* Control write status stage */
-#define CS_WRDS 0x0003 /* Control write data stage */
-#define CS_RDSS 0x0002 /* Control read status stage */
-#define CS_RDDS 0x0001 /* Control read data stage */
-#define CS_IDST 0x0000 /* Idle or setup stage */
+#define VBINT 0x8000 /* b15: VBUS interrupt */
+#define RESM 0x4000 /* b14: Resume interrupt */
+#define SOFR 0x2000 /* b13: SOF frame update interrupt */
+#define DVST 0x1000 /* b12: Device state transition interrupt */
+#define CTRT 0x0800 /* b11: Control transfer stage transition interrupt */
+#define BEMP 0x0400 /* b10: Buffer empty interrupt */
+#define NRDY 0x0200 /* b9: Buffer not ready interrupt */
+#define BRDY 0x0100 /* b8: Buffer ready interrupt */
+#define VBSTS 0x0080 /* b7: VBUS input port */
+#define DVSQ 0x0070 /* b6-4: Device state */
+#define DS_SPD_CNFG 0x0070 /* Suspend Configured */
+#define DS_SPD_ADDR 0x0060 /* Suspend Address */
+#define DS_SPD_DFLT 0x0050 /* Suspend Default */
+#define DS_SPD_POWR 0x0040 /* Suspend Powered */
+#define DS_SUSP 0x0040 /* Suspend */
+#define DS_CNFG 0x0030 /* Configured */
+#define DS_ADDS 0x0020 /* Address */
+#define DS_DFLT 0x0010 /* Default */
+#define DS_POWR 0x0000 /* Powered */
+#define DVSQS 0x0030 /* b5-4: Device state */
+#define VALID 0x0008 /* b3: Setup packet detected flag */
+#define CTSQ 0x0007 /* b2-0: Control transfer stage */
+#define CS_SQER 0x0006 /* Sequence error */
+#define CS_WRND 0x0005 /* Control write nodata status stage */
+#define CS_WRSS 0x0004 /* Control write status stage */
+#define CS_WRDS 0x0003 /* Control write data stage */
+#define CS_RDSS 0x0002 /* Control read status stage */
+#define CS_RDDS 0x0001 /* Control read data stage */
+#define CS_IDST 0x0000 /* Idle or setup stage */
/* Interrupt Status Register 1 */
-#define OVRCR 0x8000 /* b15: Over-current interrupt */
-#define BCHG 0x4000 /* b14: USB bus chenge interrupt */
-#define DTCH 0x1000 /* b12: Detach sense interrupt */
-#define ATTCH 0x0800 /* b11: Attach sense interrupt */
-#define EOFERR 0x0040 /* b6: EOF-error interrupt */
-#define SIGN 0x0020 /* b5: Setup ignore interrupt */
-#define SACK 0x0010 /* b4: Setup acknowledge interrupt */
+#define OVRCR 0x8000 /* b15: Over-current interrupt */
+#define BCHG 0x4000 /* b14: USB bus chenge interrupt */
+#define DTCH 0x1000 /* b12: Detach sense interrupt */
+#define ATTCH 0x0800 /* b11: Attach sense interrupt */
+#define EOFERR 0x0040 /* b6: EOF-error interrupt */
+#define SIGN 0x0020 /* b5: Setup ignore interrupt */
+#define SACK 0x0010 /* b4: Setup acknowledge interrupt */
/* Frame Number Register */
-#define OVRN 0x8000 /* b15: Overrun error */
-#define CRCE 0x4000 /* b14: Received data error */
-#define FRNM 0x07FF /* b10-0: Frame number */
+#define OVRN 0x8000 /* b15: Overrun error */
+#define CRCE 0x4000 /* b14: Received data error */
+#define FRNM 0x07FF /* b10-0: Frame number */
/* Micro Frame Number Register */
-#define UFRNM 0x0007 /* b2-0: Micro frame number */
+#define UFRNM 0x0007 /* b2-0: Micro frame number */
/* Default Control Pipe Maxpacket Size Register */
/* Pipe Maxpacket Size Register */
-#define DEVSEL 0xF000 /* b15-14: Device address select */
-#define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */
+#define DEVSEL 0xF000 /* b15-14: Device address select */
+#define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */
/* Default Control Pipe Control Register */
-#define BSTS 0x8000 /* b15: Buffer status */
-#define SUREQ 0x4000 /* b14: Send USB request */
-#define CSCLR 0x2000 /* b13: complete-split status clear */
-#define CSSTS 0x1000 /* b12: complete-split status */
-#define SUREQCLR 0x0800 /* b11: stop setup request */
-#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
-#define SQSET 0x0080 /* b7: Sequence toggle bit set */
-#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
-#define PBUSY 0x0020 /* b5: pipe busy */
-#define PINGE 0x0010 /* b4: ping enable */
-#define CCPL 0x0004 /* b2: Enable control transfer complete */
-#define PID 0x0003 /* b1-0: Response PID */
-#define PID_STALL11 0x0003 /* STALL */
-#define PID_STALL 0x0002 /* STALL */
-#define PID_BUF 0x0001 /* BUF */
-#define PID_NAK 0x0000 /* NAK */
+#define BSTS 0x8000 /* b15: Buffer status */
+#define SUREQ 0x4000 /* b14: Send USB request */
+#define CSCLR 0x2000 /* b13: complete-split status clear */
+#define CSSTS 0x1000 /* b12: complete-split status */
+#define SUREQCLR 0x0800 /* b11: stop setup request */
+#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
+#define SQSET 0x0080 /* b7: Sequence toggle bit set */
+#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
+#define PBUSY 0x0020 /* b5: pipe busy */
+#define PINGE 0x0010 /* b4: ping enable */
+#define CCPL 0x0004 /* b2: Enable control transfer complete */
+#define PID 0x0003 /* b1-0: Response PID */
+#define PID_STALL11 0x0003 /* STALL */
+#define PID_STALL 0x0002 /* STALL */
+#define PID_BUF 0x0001 /* BUF */
+#define PID_NAK 0x0000 /* NAK */
/* Pipe Window Select Register */
-#define PIPENM 0x0007 /* b2-0: Pipe select */
+#define PIPENM 0x0007 /* b2-0: Pipe select */
/* Pipe Configuration Register */
-#define R8A66597_TYP 0xC000 /* b15-14: Transfer type */
-#define R8A66597_ISO 0xC000 /* Isochronous */
-#define R8A66597_INT 0x8000 /* Interrupt */
-#define R8A66597_BULK 0x4000 /* Bulk */
-#define R8A66597_BFRE 0x0400 /* b10: Buffer ready interrupt mode select */
-#define R8A66597_DBLB 0x0200 /* b9: Double buffer mode select */
-#define R8A66597_CNTMD 0x0100 /* b8: Continuous transfer mode select */
-#define R8A66597_SHTNAK 0x0080 /* b7: Transfer end NAK */
-#define R8A66597_DIR 0x0010 /* b4: Transfer direction select */
-#define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */
+#define R8A66597_TYP 0xC000 /* b15-14: Transfer type */
+#define R8A66597_ISO 0xC000 /* Isochronous */
+#define R8A66597_INT 0x8000 /* Interrupt */
+#define R8A66597_BULK 0x4000 /* Bulk */
+#define R8A66597_BFRE 0x0400 /* b10: Buffer ready interrupt mode select */
+#define R8A66597_DBLB 0x0200 /* b9: Double buffer mode select */
+#define R8A66597_CNTMD 0x0100 /* b8: Continuous transfer mode select */
+#define R8A66597_SHTNAK 0x0080 /* b7: Transfer end NAK */
+#define R8A66597_DIR 0x0010 /* b4: Transfer direction select */
+#define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */
/* Pipe Buffer Configuration Register */
-#define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */
-#define BUFNMB 0x007F /* b6-0: Pipe buffer number */
-#define PIPE0BUF 256
-#define PIPExBUF 64
+#define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */
+#define BUFNMB 0x007F /* b6-0: Pipe buffer number */
+#define PIPE0BUF 256
+#define PIPExBUF 64
/* Pipe Maxpacket Size Register */
-#define MXPS 0x07FF /* b10-0: Maxpacket size */
+#define MXPS 0x07FF /* b10-0: Maxpacket size */
/* Pipe Cycle Configuration Register */
-#define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */
-#define IITV 0x0007 /* b2-0: Isochronous interval */
+#define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */
+#define IITV 0x0007 /* b2-0: Isochronous interval */
/* Pipex Control Register */
-#define BSTS 0x8000 /* b15: Buffer status */
-#define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */
-#define CSCLR 0x2000 /* b13: complete-split status clear */
-#define CSSTS 0x1000 /* b12: complete-split status */
-#define ATREPM 0x0400 /* b10: Auto repeat mode */
-#define ACLRM 0x0200 /* b9: Out buffer auto clear mode */
-#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
-#define SQSET 0x0080 /* b7: Sequence toggle bit set */
-#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
-#define PBUSY 0x0020 /* b5: pipe busy */
-#define PID 0x0003 /* b1-0: Response PID */
+#define BSTS 0x8000 /* b15: Buffer status */
+#define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */
+#define CSCLR 0x2000 /* b13: complete-split status clear */
+#define CSSTS 0x1000 /* b12: complete-split status */
+#define ATREPM 0x0400 /* b10: Auto repeat mode */
+#define ACLRM 0x0200 /* b9: Out buffer auto clear mode */
+#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
+#define SQSET 0x0080 /* b7: Sequence toggle bit set */
+#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
+#define PBUSY 0x0020 /* b5: pipe busy */
+#define PID 0x0003 /* b1-0: Response PID */
/* PIPExTRE */
-#define TRENB 0x0200 /* b9: Transaction counter enable */
-#define TRCLR 0x0100 /* b8: Transaction counter clear */
+#define TRENB 0x0200 /* b9: Transaction counter enable */
+#define TRCLR 0x0100 /* b8: Transaction counter clear */
/* PIPExTRN */
-#define TRNCNT 0xFFFF /* b15-0: Transaction counter */
+#define TRNCNT 0xFFFF /* b15-0: Transaction counter */
/* DEVADDx */
-#define UPPHUB 0x7800
-#define HUBPORT 0x0700
-#define USBSPD 0x00C0
-#define RTPORT 0x0001
+#define UPPHUB 0x7800
+#define HUBPORT 0x0700
+#define USBSPD 0x00C0
+#define RTPORT 0x0001
/* Suspend Mode Register */
-#define SUSPM 0x4000 /* b14: Suspend */
+#define SUSPM 0x4000 /* b14: Suspend */
#define R8A66597_MAX_NUM_PIPE 10
#define R8A66597_BUF_BSIZE 8
#define BULK_OUT_PIPENUM 4
#define BULK_OUT_BUFNUM 40
-#define check_bulk_or_isoc(pipenum) ((pipenum >= 1 && pipenum <= 5))
-#define check_interrupt(pipenum) ((pipenum >= 6 && pipenum <= 9))
-#define make_devsel(addr) (addr << 12)
+#define make_devsel(addr) ((addr) << 12)
struct r8a66597 {
unsigned long reg;
if (len & 0x00000003) {
unsigned long tmp = readl(fifoaddr);
+
memcpy((unsigned char *)buf + count * 4, &tmp, len & 0x03);
}
}
u16 val, u16 pat, unsigned long offset)
{
u16 tmp;
+
tmp = r8a66597_read(r8a66597, offset);
tmp = tmp & (~pat);
tmp = tmp | val;
#define get_pipetrn_addr(pipenum) (PIPE1TRN + (pipenum - 1) * 4)
#define get_devadd_addr(address) (DEVADD0 + address * 2)
-
/* USB HUB CONSTANTS (not OHCI-specific; see hub.h, based on usb_ohci.h) */
/* destination of request */
/* roothub.a masks */
#define RH_A_NDP (0xff << 0) /* number of downstream ports */
-#define RH_A_PSM (1 << 8) /* power switching mode */
-#define RH_A_NPS (1 << 9) /* no power switching */
-#define RH_A_DT (1 << 10) /* device type (mbz) */
-#define RH_A_OCPM (1 << 11) /* over current protection mode */
-#define RH_A_NOCP (1 << 12) /* no over current protection */
+#define RH_A_PSM BIT(8) /* power switching mode */
+#define RH_A_NPS BIT(9) /* no power switching */
+#define RH_A_DT BIT(10) /* device type (mbz) */
+#define RH_A_OCPM BIT(11) /* over current protection mode */
+#define RH_A_NOCP BIT(12) /* no over current protection */
#define RH_A_POTPGT (0xff << 24) /* power on to power good time */
#endif /* __R8A66597_H__ */
projects / u-boot.git / commitdiff