The Amlogic Meson GXL (S905X and S905D) is an ARM SoC with a
quad-core Cortex-A53 CPU and a Mali-450 GPU.
+config MESON_GXM
+ bool "Support Meson GXM"
+ select ARM64
+ select CLK
+ select DM
+ select DM_SERIAL
+ help
+ The Amlogic Meson GXM (S912) is an ARM SoC with an
+ octo-core Cortex-A53 CPU and a Mali-T860 GPU.
+
if MESON_GXBB
config TARGET_ODROID_C2
endif
+if MESON_GXM
+
+config TARGET_KHADAS_VIM2
+ bool "KHADAS-VIM2"
+ help
+ Khadas VIM2 is a single board computer based on Meson GXM
+ with 2/3 GiB of RAM, Ethernet, HDMI, 4 USB, micro-SD slot,
+ eMMC, IR receiver and a 40-pin GPIO header.
+
+endif
+
config SYS_SOC
default "meson"
source "board/amlogic/khadas-vim/Kconfig"
+source "board/amlogic/khadas-vim2/Kconfig"
+
endif
--- /dev/null
+if TARGET_KHADAS_VIM2
+
+config SYS_BOARD
+ default "khadas-vim2"
+
+config SYS_VENDOR
+ default "amlogic"
+
+config SYS_CONFIG_NAME
+ default "khadas-vim2"
+
+endif
--- /dev/null
+KHADAS-VIM2
+M: Neil Armstrong <narmstrong@baylibre.com>
+S: Maintained
+F: board/amlogic/khadas-vim2/
+F: include/configs/khadas-vim2.h
+F: configs/khadas-vim2_defconfig
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2016 BayLibre, SAS
+# Author: Neil Armstrong <narmstrong@baylibre.com>
+
+obj-y := khadas-vim2.o
--- /dev/null
+U-Boot for Khadas VIM2
+=======================
+
+Khadas VIM2 is an Open Source DIY Box manufactured by Shenzhen Wesion
+Technology Co., Ltd with the following specifications:
+
+ - Amlogic S912 ARM Cortex-A53 octo-core SoC @ 1.5GHz
+ - ARM Mali T860 GPU
+ - 2/3GB DDR4 SDRAM
+ - 10/100/1000 Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 40-pin GPIO header
+ - 2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG
+ - 16GB/32GB/64GB eMMC
+ - 2MB SPI Flash
+ - microSD
+ - SDIO Wifi Module, Bluetooth
+ - Two channels IR receiver
+
+Currently the u-boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+ - I2C
+ - Regulators
+ - Reset controller
+ - Clock controller
+ - USB Host
+ - ADC
+
+U-Boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make khadas-vim2_defconfig
+ > make
+
+Image creation
+==============
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain them from
+the git tree published by the board vendor:
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/khadas/u-boot -b Vim vim-u-boot
+ > cd vim-u-boot
+ > make kvim_defconfig
+ > make
+ > export FIPDIR=$PWD/fip
+
+Go back to mainline U-Boot source tree then :
+ > mkdir fip
+
+ > cp $FIPDIR/gxl/bl2.bin fip/
+ > cp $FIPDIR/gxl/acs.bin fip/
+ > cp $FIPDIR/gxl/bl21.bin fip/
+ > cp $FIPDIR/gxl/bl30.bin fip/
+ > cp $FIPDIR/gxl/bl301.bin fip/
+ > cp $FIPDIR/gxl/bl31.img fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl30.bin \
+ fip/zero_tmp \
+ fip/bl30_zero.bin \
+ fip/bl301.bin \
+ fip/bl301_zero.bin \
+ fip/bl30_new.bin \
+ bl30
+
+ > python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ > $FIPDIR/blx_fix.sh \
+ fip/bl2_acs.bin \
+ fip/zero_tmp \
+ fip/bl2_zero.bin \
+ fip/bl21.bin \
+ fip/bl21_zero.bin \
+ fip/bl2_new.bin \
+ bl2
+
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
+ > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \
+ --output fip/u-boot.bin \
+ --bl2 fip/bl2.n.bin.sig \
+ --bl30 fip/bl30_new.bin.enc \
+ --bl31 fip/bl31.img.enc \
+ --bl33 fip/bl33.bin.enc
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <environment.h>
+#include <asm/io.h>
+#include <asm/arch/gx.h>
+#include <asm/arch/mem.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+
+#define EFUSE_SN_OFFSET 20
+#define EFUSE_SN_SIZE 16
+#define EFUSE_MAC_OFFSET 52
+#define EFUSE_MAC_SIZE 6
+
+int board_init(void)
+{
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ u8 mac_addr[EFUSE_MAC_SIZE];
+ char serial[EFUSE_SN_SIZE];
+ ssize_t len;
+
+ meson_gx_eth_init(PHY_INTERFACE_MODE_RGMII, 0);
+
+ /* Reset PHY on GPIOZ_14 */
+ clrbits_le32(GX_GPIO_EN(3), BIT(14));
+ clrbits_le32(GX_GPIO_OUT(3), BIT(14));
+ mdelay(10);
+ setbits_le32(GX_GPIO_OUT(3), BIT(14));
+
+ if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+ len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+ mac_addr, EFUSE_MAC_SIZE);
+ if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr))
+ eth_env_set_enetaddr("ethaddr", mac_addr);
+ }
+
+ if (!env_get("serial#")) {
+ len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+ EFUSE_SN_SIZE);
+ if (len == EFUSE_SN_SIZE)
+ env_set("serial#", serial);
+ }
+
+ return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ meson_gx_init_reserved_memory(blob);
+
+ return 0;
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_MESON_GXM=y
+CONFIG_TARGET_KHADAS_VIM2=y
+CONFIG_DEBUG_UART_BASE=0xc81004c0
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" khadas-vim2"
+CONFIG_DEFAULT_DEVICE_TREE="meson-gxm-khadas-vim2"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_ADC=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_REGULATOR=y
+CONFIG_ADC=y
+CONFIG_SARADC_MESON=y
+CONFIG_OF_CONTROL=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_GXL=y
+CONFIG_DEBUG_UART_MESON=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_XHCI_DWC3_OF_SIMPLE=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_STORAGE=y
+CONFIG_PHY=y
+CONFIG_MESON_GXL_USB_PHY=y
+CONFIG_MTD=y
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration for Khadas VIM2
+ *
+ * Copyright (C) 2017 Baylibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MISC_INIT_R
+
+#define MESON_FDTFILE_SETTING "fdtfile=amlogic/meson-gxm-khadas-vim2.dtb\0"
+
+#include <configs/meson-gx-common.h>
+
+#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff