+++ /dev/null
-/*
- * Copyright 2009,2012 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <hwconfig.h>
-#include <command.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/mpc85xx_gpio.h>
-#include <asm/fsl_serdes.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#include <libfdt.h>
-#include <fdt_support.h>
-#include <fsl_mdio.h>
-#include <tsec.h>
-#include <vsc7385.h>
-#include <netdev.h>
-#include <mmc.h>
-#include <malloc.h>
-#include <i2c.h>
-
-#if defined(CONFIG_PCI)
-#include <asm/fsl_pci.h>
-#include <pci.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#if defined(CONFIG_PCI)
-void pci_init_board(void)
-{
- fsl_pcie_init_board(0);
-}
-
-void ft_pci_board_setup(void *blob)
-{
- FT_FSL_PCI_SETUP;
-}
-#endif
-
-#define BOARD_PERI_RST_SET (VSC7385_RST_SET | SLIC_RST_SET | \
- SGMII_PHY_RST_SET | PCIE_RST_SET | \
- RGMII_PHY_RST_SET)
-
-#define SYSCLK_MASK 0x00200000
-#define BOARDREV_MASK 0x10100000
-#define BOARDREV_B 0x10100000
-#define BOARDREV_C 0x00100000
-#define BOARDREV_D 0x00000000
-
-#define SYSCLK_66 66666666
-#define SYSCLK_50 50000000
-#define SYSCLK_100 100000000
-
-unsigned long get_board_sys_clk(ulong dummy)
-{
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 ddr_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_DDR_RATIO;
-
- ddr_ratio >>= MPC85xx_PORPLLSR_DDR_RATIO_SHIFT;
- switch (ddr_ratio) {
- case 0x0C:
- return SYSCLK_66;
- case 0x0A:
- case 0x08:
- return SYSCLK_100;
- default:
- puts("ERROR: unknown DDR ratio\n");
- return SYSCLK_100;
- }
-}
-
-unsigned long get_board_ddr_clk(ulong dummy)
-{
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- u32 ddr_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_DDR_RATIO;
-
- ddr_ratio >>= MPC85xx_PORPLLSR_DDR_RATIO_SHIFT;
- switch (ddr_ratio) {
- case 0x0C:
- case 0x0A:
- return SYSCLK_66;
- case 0x08:
- return SYSCLK_100;
- default:
- puts("ERROR: unknown DDR ratio\n");
- return SYSCLK_100;
- }
-}
-
-#ifdef CONFIG_MMC
-int board_early_init_f(void)
-{
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-
- setbits_be32(&gur->pmuxcr,
- (MPC85xx_PMUXCR_SDHC_CD |
- MPC85xx_PMUXCR_SDHC_WP));
-
- /* All the device are enable except for SRIO12 */
- setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_SRIO);
- return 0;
-}
-#endif
-
-#define GPIO_DIR 0x0f3a0000
-#define GPIO_ODR 0x00000000
-#define GPIO_DAT 0x001a0000
-
-int checkboard(void)
-{
- ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR + 0xC00);
-
- /*
- * GPIO
- * 0 - 3: CarryBoard Input;
- * 4 - 7: CarryBoard Output;
- * 8 : Mux as SDHC_CD (card detection)
- * 9 : Mux as SDHC_WP
- * 10 : Clear Watchdog timer
- * 11 : LED Input
- * 12 : Output to 1
- * 13 : Open Drain
- * 14 : LED Output
- * 15 : Switch Input
- *
- * Set GPIOs 11, 12, 14 to 1.
- */
- out_be32(&pgpio->gpodr, GPIO_ODR);
- mpc85xx_gpio_set(0xffffffff, GPIO_DIR, GPIO_DAT);
-
- puts("Board: Freescale COM Express P2020\n");
- return 0;
-}
-
-#define M41ST85W_I2C_BUS 1
-#define M41ST85W_I2C_ADDR 0x68
-#define M41ST85W_ERROR(fmt, args...) printf("ERROR: M41ST85W: " fmt, ##args)
-
-static void m41st85w_clear_bit(u8 reg, u8 mask, const char *name)
-{
- u8 data;
-
- if (i2c_read(M41ST85W_I2C_ADDR, reg, 1, &data, 1)) {
- M41ST85W_ERROR("unable to read %s bit\n", name);
- return;
- }
-
- if (data & mask) {
- data &= ~mask;
- if (i2c_write(M41ST85W_I2C_ADDR, reg, 1, &data, 1)) {
- M41ST85W_ERROR("unable to clear %s bit\n", name);
- return;
- }
- }
-}
-
-#define M41ST85W_REG_SEC2 0x01
-#define M41ST85W_REG_SEC2_ST 0x80
-
-#define M41ST85W_REG_ALHOUR 0x0c
-#define M41ST85W_REG_ALHOUR_HT 0x40
-
-/*
- * The P2020COME board has a STMicro M41ST85W RTC/watchdog
- * at i2c bus 1 address 0x68.
- */
-static void start_rtc(void)
-{
- unsigned int bus = i2c_get_bus_num();
-
- if (i2c_set_bus_num(M41ST85W_I2C_BUS)) {
- M41ST85W_ERROR("unable to set i2c bus\n");
- goto out;
- }
-
- /* ensure ST (stop) and HT (halt update) bits are cleared */
- m41st85w_clear_bit(M41ST85W_REG_SEC2, M41ST85W_REG_SEC2_ST, "ST");
- m41st85w_clear_bit(M41ST85W_REG_ALHOUR, M41ST85W_REG_ALHOUR_HT, "HT");
-
-out:
- /* reset the i2c bus */
- i2c_set_bus_num(bus);
-}
-
-int board_early_init_r(void)
-{
- start_rtc();
- return 0;
-}
-
-#define M41ST85W_REG_WATCHDOG 0x09
-#define M41ST85W_REG_WATCHDOG_WDS 0x80
-#define M41ST85W_REG_WATCHDOG_BMB0 0x04
-
-void board_reset(void)
-{
- u8 data = M41ST85W_REG_WATCHDOG_WDS | M41ST85W_REG_WATCHDOG_BMB0;
-
- /* set the hardware watchdog timeout to 1/16 second, then hang */
- i2c_set_bus_num(M41ST85W_I2C_BUS);
- i2c_write(M41ST85W_I2C_ADDR, M41ST85W_REG_WATCHDOG, 1, &data, 1);
-
- while (1)
- /* hang */;
-}
-
-#ifdef CONFIG_TSEC_ENET
-int board_eth_init(bd_t *bis)
-{
- struct fsl_pq_mdio_info mdio_info;
- struct tsec_info_struct tsec_info[4];
- int num = 0;
-
-#ifdef CONFIG_TSEC1
- SET_STD_TSEC_INFO(tsec_info[num], 1);
- num++;
-#endif
-#ifdef CONFIG_TSEC2
- SET_STD_TSEC_INFO(tsec_info[num], 2);
- num++;
-#endif
-#ifdef CONFIG_TSEC3
- SET_STD_TSEC_INFO(tsec_info[num], 3);
- if (is_serdes_configured(SGMII_TSEC3)) {
- puts("eTSEC3 is in sgmii mode.");
- tsec_info[num].flags |= TSEC_SGMII;
- }
- num++;
-#endif
- if (!num) {
- printf("No TSECs initialized\n");
- return 0;
- }
-
- mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
- mdio_info.name = DEFAULT_MII_NAME;
- fsl_pq_mdio_init(bis, &mdio_info);
-
- tsec_eth_init(bis, tsec_info, num);
-
- return pci_eth_init(bis);
-}
-#endif
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, bd_t *bd)
-{
- phys_addr_t base;
- phys_size_t size;
-
- ft_cpu_setup(blob, bd);
-
- base = getenv_bootm_low();
- size = getenv_bootm_size();
-
-#if defined(CONFIG_PCI)
- ft_pci_board_setup(blob);
-#endif
-
- fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-#ifdef CONFIG_HAS_FSL_DR_USB
- fdt_fixup_dr_usb(blob, bd);
-#endif
-
- return 0;
-}
-#endif
+++ /dev/null
-/*
- * Copyright 2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS,
- MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 ,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
- MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 ,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
- MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 ,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
- MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
-
- /* TLB 1 */
- /* *I*** - Covers boot page */
- SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_4K, 1),
-
- /* *I*G* - CCSRBAR */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_1M, 1),
-
-#if defined(CONFIG_PCI)
- /* *I*G* - PCI3 - PCI2 0x8000,0000 - 0xbfff,ffff, size = 1G */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 2, BOOKE_PAGESZ_1G, 1),
-
- /* *I*G* - PCI1 0xC000,0000 - 0xcfff,ffff, size = 256M */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_VIRT,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_256M, 1),
-
- /* *I*G* - PCI1 0xD000,0000 - 0xDFFF,FFFF, size = 256M */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x10000000,
- CONFIG_SYS_PCIE1_MEM_PHYS + 0x10000000,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_256M, 1),
-
- /*
- * *I*G* - PCI I/O
- *
- * PCI3 => 0xFFC10000
- * PCI2 => 0xFFC2,0000
- * PCI1 => 0xFFC3,0000
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 5, BOOKE_PAGESZ_256K, 1),
-#endif /* #if defined(CONFIG_PCI) */
-
-#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L2_ADDR)
- /* *I*G - DDR3 2G Part 1: 0 - 0x3fff,ffff , size = 1G */
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_256K, 1),
-
- /* DDR3 2G Part 2: 0x4000,0000 - 0x7fff,ffff , size = 1G */
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
- CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 7, BOOKE_PAGESZ_256K, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
+++ /dev/null
-/*
- * Copyright 2009-2010,2012 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* The P2020COME board is only booted via the Freescale On-Chip ROM */
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-
-#define CONFIG_SYS_TEXT_BASE 0xf8f80000
-#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc
-
-#ifdef CONFIG_SDCARD
-#define CONFIG_RAMBOOT_SDCARD 1
-#endif
-
-#ifdef CONFIG_SPIFLASH
-#define CONFIG_RAMBOOT_SPIFLASH 1
-#endif
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_P2020 1
-#define CONFIG_P2020COME 1
-#define CONFIG_FSL_ELBC 1 /* Enable eLBC Support */
-#define CONFIG_MP
-
-#define CONFIG_PCI 1 /* Enable PCI/PCIE */
-#if defined(CONFIG_PCI)
-#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */
-#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */
-#define CONFIG_PCIE3 1 /* PCIE controller 3 (slot 3) */
-
-#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
-#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
-#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-#endif /* #if defined(CONFIG_PCI) */
-#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#define CONFIG_ENV_OVERWRITE
-
-#if defined(CONFIG_PCI)
-#define CONFIG_E1000 1 /* E1000 pci Ethernet card */
-#endif
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_board_ddr_clk(unsigned long dummy);
-extern unsigned long get_board_sys_clk(unsigned long dummy);
-#endif
-
-/*
- * For P2020COME DDRCLK and SYSCLK are from the same oscillator
- * For DA phase the SYSCLK is 66MHz
- * For EA phase the SYSCLK is 100MHz
- */
-#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0)
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
-
-#define CONFIG_HWCONFIG
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch prediction */
-
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-
-#define CONFIG_ENABLE_36BIT_PHYS 1
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
-#endif
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x1fffffff
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-
- /*
- * Config the L2 Cache as L2 SRAM
- */
-#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull
-#else
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
-#endif
-#define CONFIG_SYS_L2_SIZE (512 << 10)
-#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR \
- + CONFIG_SYS_L2_SIZE)
-
-#define CONFIG_SYS_CCSRBAR 0xffe00000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR3
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#define CONFIG_DDR_SPD
-
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
-
-#define CONFIG_SYS_SDRAM_SIZE 2048ULL /* DDR size on P2020COME */
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_NUM_DDR_CONTROLLERS 1
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 2
-
-#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
-#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
-#define CONFIG_SYS_DDR_SBE 0x00ff0000
-
-#define CONFIG_SYS_SPD_BUS_NUM 1
-#define SPD_EEPROM_ADDRESS 0x53
-
-/*
- * Memory map
- *
- * 0x0000_0000 0x7fff_ffff DDR3 2G Cacheable
- * 0x8000_0000 0x9fff_ffff PCI Express 3 Mem 1G non-cacheable
- * 0xa000_0000 0xbfff_ffff PCI Express 2 Mem 1G non-cacheable
- * 0xc000_0000 0xdfff_ffff PCI Express 1 Mem 1G non-cacheable
- * 0xffc1_0000 0xffc1_ffff PCI Express 3 IO 64K non-cacheable
- * 0xffc2_0000 0xffc2_ffff PCI Express 2 IO 64K non-cacheable
- * 0xffc3_0000 0xffc3_ffff PCI Express 1 IO 64K non-cacheable
- *
- * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
- * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
- */
-
-/*
- * Local Bus Definitions
- */
-
-/* There is no NOR Flash on P2020COME */
-#define CONFIG_SYS_NO_FLASH
-
-#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
-#define CONFIG_HWCONFIG
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
-/* the assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
- ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
- CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#else
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
-#endif
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
- - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
-/* new uImage format support */
-#define CONFIG_FIT 1
-#define CONFIG_FIT_VERBOSE 1
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_ID_EEPROM
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR2 0x18
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/*
- * eSPI - Enhanced SPI
- */
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED 10000000
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-#if defined(CONFIG_PCI)
-
-/* controller 3, Slot 3, tgtid 3, Base address 8000 */
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc10000
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc10000
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 2, Slot 2, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc20000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc20000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 1, Slot 1, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc30000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc30000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
-#undef CONFIG_RTL8139
-
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x) (x)
-#define _IO_BASE 0x00000000
-#endif
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
-
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC3"
-
-#define TSEC1_PHY_ADDR 0
-#define TSEC2_PHY_ADDR 2
-#define TSEC3_PHY_ADDR 1
-
-#undef CONFIG_VSC7385_ENET
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC3_PHYIDX 0
-
-#define CONFIG_ETHPRIME "eTSEC1"
-
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-
-#endif /* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#if defined(CONFIG_RAMBOOT_SDCARD)
- #define CONFIG_ENV_IS_IN_MMC 1
- #define CONFIG_FSL_FIXED_MMC_LOCATION
- #define CONFIG_ENV_SIZE 0x2000
- #define CONFIG_SYS_MMC_ENV_DEV 0
-#elif defined(CONFIG_RAMBOOT_SPIFLASH)
- #define CONFIG_ENV_IS_IN_SPI_FLASH
- #define CONFIG_ENV_SPI_BUS 0
- #define CONFIG_ENV_SPI_CS 0
- #define CONFIG_ENV_SPI_MAX_HZ 10000000
- #define CONFIG_ENV_SPI_MODE 0
- #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
- #define CONFIG_ENV_SECT_SIZE 0x10000
- #define CONFIG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_LOADS_ECHO 1
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SETEXPR
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#endif
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_MMC 1
-
-#ifdef CONFIG_MMC
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#define CONFIG_CMD_MMC
-#define CONFIG_DOS_PARTITION
-#define CONFIG_FSL_ESDHC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
-#endif /* CONFIG_MMC */
-
-#define CONFIG_HAS_FSL_DR_USB
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
-#endif
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/* Misc Extra Settings */
-#define CONFIG_CMD_DHCP 1
-
-#define CONFIG_CMD_DATE 1
-#define CONFIG_RTC_M41T62 1
-#define CONFIG_SYS_RTC_BUS_NUM 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
- /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20)
-#define CONFIG_SYS_BOOTM_LEN (64 << 20)
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#define CONFIG_HAS_ETH3
-#endif
-
-#define CONFIG_HOSTNAME unknown
-#define CONFIG_ROOTPATH "/opt/nfsroot"
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_UBOOTPATH u-boot.bin
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-
-#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:ecc=on\0" \
- "bootcmd=run sdboot\0" \
- "sdboot=setenv bootargs root=/dev/mmcblk0p2 rw " \
- "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
- "$othbootargs; mmcinfo; " \
- "ext2load mmc 0:2 $loadaddr /boot/$bootfile; " \
- "ext2load mmc 0:2 $fdtaddr /boot/$fdtfile; " \
- "bootm $loadaddr - $fdtaddr\0" \
- "sdfatboot=setenv bootargs root=/dev/ram rw " \
- "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
- "$othbootargs; mmcinfo; " \
- "fatload mmc 0:1 $loadaddr $bootfile; " \
- "fatload mmc 0:1 $fdtaddr $fdtfile; " \
- "fatload mmc 0:1 $ramdiskaddr $ramdiskfile; " \
- "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
- "usbboot=setenv bootargs root=/dev/sda1 rw " \
- "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\
- "$othbootargs; " \
- "usb start; " \
- "ext2load usb 0:1 $loadaddr /boot/$bootfile; " \
- "ext2load usb 0:1 $fdtaddr /boot/$fdtfile; " \
- "bootm $loadaddr - $fdtaddr\0" \
- "usbfatboot=setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "usb start; " \
- "fatload usb 0:2 $loadaddr $bootfile; " \
- "fatload usb 0:2 $fdtaddr $fdtfile; " \
- "fatload usb 0:2 $ramdiskaddr $ramdiskfile; " \
- "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
- "usbext2boot=setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "usb start; " \
- "ext2load usb 0:4 $loadaddr $bootfile; " \
- "ext2load usb 0:4 $fdtaddr $fdtfile; " \
- "ext2load usb 0:4 $ramdiskaddr $ramdiskfile; " \
- "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
- "upgradespi=sf probe 0; " \
- "setenv startaddr 0; " \
- "setenv erasesize a0000; " \
- "tftp 1000000 $tftppath/$uboot_spi; " \
- "sf erase $startaddr $erasesize; " \
- "sf write 1000000 $startaddr $filesize; " \
- "sf erase 100000 120000\0" \
- "clearspienv=sf probe 0;sf erase 100000 20000\0" \
- "othbootargs=ramdisk_size=700000 cache-sram-size=0x10000\0" \
- "netdev=eth0\0" \
- "rootdelaysecond=15\0" \
- "uboot_nor=u-boot-nor.bin\0" \
- "uboot_spi=u-boot-p2020.spi\0" \
- "uboot_sd=u-boot-p2020.bin\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=2000000\0" \
- "ramdiskfile=rootfs-dev.ext2.img\0" \
- "fdtaddr=c00000\0" \
- "fdtfile=uImage-2.6.32-p2020.dtb\0" \
- "tftppath=p2020\0"
-
-#define CONFIG_HDBOOT \
- "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "usb start;" \
- "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
- "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "\
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $tftppath/$bootfile;" \
- "tftp $fdtaddr $tftppath/$fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $tftppath/$ramdiskfile;" \
- "tftp $loadaddr $tftppath/$bootfile;" \
- "tftp $fdtaddr $tftppath/$fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff