drivers: spl: consistently use the $(SPL_TPL_) macro

To simplify drivers/Makefile a bit when using TPL/SPL, we consistently
use the $(SPL_TPL_) macro to test for drivers that have separate
configuration symbols for the full U-boot, SPL and TPL stages.
Instead of explicitly repeating them in two separate if-guarded
sections of the Makefile, we can now simply list these options once.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

diff --git a/drivers/Makefile b/drivers/Makefile
index e4a9cb419585cfaf83bed7df7d18718168812658..a41444ace14b381860eec9bb4752742c7eb8252a 100644 (file)
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -2,33 +2,34 @@
 # SPDX-License-Identifier:     GPL-2.0+
 #
 
-obj-$(CONFIG_$(SPL_TPL_)DM)    += core/
-obj-$(CONFIG_$(SPL_)CLK)       += clk/
-obj-$(CONFIG_$(SPL_)LED)       += led/
-obj-$(CONFIG_$(SPL_)PHY)       += phy/
-obj-$(CONFIG_$(SPL_)PINCTRL)   += pinctrl/
-obj-$(CONFIG_$(SPL_)RAM)       += ram/
+obj-$(CONFIG_$(SPL_TPL_)CLK) += clk/
+obj-$(CONFIG_$(SPL_TPL_)DM) += core/
+obj-$(CONFIG_$(SPL_TPL_)DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
+obj-$(CONFIG_$(SPL_TPL_)I2C_SUPPORT) += i2c/
+obj-$(CONFIG_$(SPL_TPL_)LED) += led/
+obj-$(CONFIG_$(SPL_TPL_)MMC_SUPPORT) += mmc/
+obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/
+obj-$(CONFIG_$(SPL_TPL_)PHY) += phy/
+obj-$(CONFIG_$(SPL_TPL_)PINCTRL) += pinctrl/
+obj-$(CONFIG_$(SPL_TPL_)RAM) += ram/
+obj-$(CONFIG_$(SPL_TPL_)SERIAL_SUPPORT) += serial/
+obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPORT) += mtd/spi/
+obj-$(CONFIG_$(SPL_TPL_)SPI_SUPPORT) += spi/
 
+ifndef CONFIG_TPL_BUILD
 ifdef CONFIG_SPL_BUILD
 
 obj-$(CONFIG_SPL_CPU_SUPPORT) += cpu/
 obj-$(CONFIG_SPL_CRYPTO_SUPPORT) += crypto/
-obj-$(CONFIG_SPL_I2C_SUPPORT) += i2c/
 obj-$(CONFIG_SPL_GPIO_SUPPORT) += gpio/
-obj-$(CONFIG_SPL_MMC_SUPPORT) += mmc/
 obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
 obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/
 obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/
 obj-$(CONFIG_ALTERA_SDRAM) += ddr/altera/
-obj-$(CONFIG_SPL_SERIAL_SUPPORT) += serial/
-obj-$(CONFIG_SPL_SPI_SUPPORT) += spi/
 obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/
 obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/
-obj-$(CONFIG_SPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
 obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd/
-obj-$(CONFIG_SPL_NAND_SUPPORT) += mtd/nand/
 obj-$(CONFIG_SPL_ONENAND_SUPPORT) += mtd/onenand/
-obj-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += mtd/spi/
 obj-$(CONFIG_SPL_UBI) += mtd/ubispl/
 obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/
 obj-$(CONFIG_SPL_ETH_SUPPORT) += net/
@@ -49,18 +50,13 @@ obj-$(CONFIG_SPL_SATA_SUPPORT) += ata/ scsi/
 obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/
 obj-$(CONFIG_SPL_MMC_SUPPORT) += block/
 obj-$(CONFIG_SPL_FPGA_SUPPORT) += fpga/
+
+endif
 endif
 
 ifdef CONFIG_TPL_BUILD
 
-obj-$(CONFIG_TPL_I2C_SUPPORT) += i2c/
-obj-$(CONFIG_TPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
-obj-$(CONFIG_TPL_MMC_SUPPORT) += mmc/
 obj-$(CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
-obj-$(CONFIG_TPL_NAND_SUPPORT) += mtd/nand/
-obj-$(CONFIG_TPL_SERIAL_SUPPORT) += serial/
-obj-$(CONFIG_TPL_SPI_FLASH_SUPPORT) += mtd/spi/
-obj-$(CONFIG_TPL_SPI_SUPPORT) += spi/
 
 endif