This board is still a non-generic board.
Unused code in arch/powerpc/cpu/mpc8xx/video.c should be also deleted
because CONFIG_VIDEO_ENCODER_AD7176, CONFIG_VIDEO_ENCODER_AD7177,
CONFIG_VIDEO_ENCODER_AD7179 are not defined any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
config TARGET_R360MPI
bool "Support R360MPI"
-config TARGET_RRVISION
- bool "Support RRvision"
-
config TARGET_TQM823L
bool "Support TQM823L"
endchoice
-source "board/RRvision/Kconfig"
source "board/cogent/Kconfig"
source "board/esteem192e/Kconfig"
source "board/ip860/Kconfig"
#define VIDEO_INFO_X VIDEO_LOGO_WIDTH+8
#define VIDEO_INFO_Y 16
-/************************************************************************/
-/* ** VIDEO ENCODER CONSTANTS */
-/************************************************************************/
-
-#ifdef CONFIG_VIDEO_ENCODER_AD7176
-
-#include <video_ad7176.h> /* Sets encoder data, mode, and visible and active area */
-
-#define VIDEO_I2C 1
-#define VIDEO_I2C_ADDR CONFIG_VIDEO_ENCODER_AD7176_ADDR
-#endif
-
-#ifdef CONFIG_VIDEO_ENCODER_AD7177
-
-#include <video_ad7177.h> /* Sets encoder data, mode, and visible and active area */
-
-#define VIDEO_I2C 1
-#define VIDEO_I2C_ADDR CONFIG_VIDEO_ENCODER_AD7177_ADDR
-#endif
-
-#ifdef CONFIG_VIDEO_ENCODER_AD7179
-
-#include <video_ad7179.h> /* Sets encoder data, mode, and visible and active area */
-
-#define VIDEO_I2C 1
-#define VIDEO_I2C_ADDR CONFIG_VIDEO_ENCODER_AD7179_ADDR
-#endif
-
/************************************************************************/
/* ** VIDEO MODE CONSTANTS */
/************************************************************************/
/* ** VIDEO CONTROLLER LOW-LEVEL FUNCTIONS */
/************************************************************************/
-#if !defined(CONFIG_RRVISION)
static void video_mode_dupefield (VRAM * source, VRAM * dest, int entries)
{
int i;
dest[0].lcyc++; /* Add a cycle to the first entry */
dest[entries - 1].lst = 1; /* Set end of ram entries */
}
-#endif
static void inline video_mode_addentry (VRAM * vr,
int Hx, int Vx, int Fx, int Bx,
#ifdef VIDEO_MODE_PAL
-#if defined(CONFIG_RRVISION)
-
-#define HPW 160 /* horizontal pulse width (was 139) */
-#define VPW 2 /* vertical pulse width */
-#define HBP 104 /* horizontal back porch (was 112) */
-#define VBP 19 /* vertical back porch (was 19) */
-#define VID_R 240 /* number of rows */
-
- debug ("[VIDEO CTRL] Starting to add controller entries...");
-/*
- * Even field
- */
- ADDENTRY (0, 3, 0, 3, 1, 0, 2, 0, 0);
- ADDENTRY (0, 0, 0, 3, 1, 0, HPW, 0, 0);
- ADDENTRY (3, 0, 0, 3, 1, 0, HBP + (VIDEO_COLS * 2) + 72, 0, 0);
-
- ADDENTRY (0, 0, 0, 3, 1, 0, VPW, 1, 0);
- ADDENTRY (0, 0, 0, 3, 1, 0, HPW-1, 0, 0);
- ADDENTRY (3, 0, 0, 3, 1, 0, HBP + (VIDEO_COLS * 2) + 72, 1, 0);
-
- ADDENTRY (0, 3, 0, 3, 1, 0, VBP, 1, 0);
- ADDENTRY (0, 3, 0, 3, 1, 0, HPW-1, 0, 0);
- ADDENTRY (3, 3, 0, 3, 1, 0, HBP + (VIDEO_COLS * 2) + 72, 1, 0);
-/*
- * Active area
- */
- ADDENTRY (0, 3, 0, 3, 1, 0, VID_R , 1, 0);
- ADDENTRY (0, 3, 0, 3, 1, 0, HPW-1, 0, 0);
- ADDENTRY (3, 3, 0, 3, 1, 0, HBP, 0, 0);
- ADDENTRY (3, 3, 0, 3, 0, 0, VIDEO_COLS*2, 0, 0);
- ADDENTRY (3, 3, 0, 3, 1, 0, 72, 1, 1);
-
- ADDENTRY (0, 3, 0, 3, 1, 0, 51, 1, 0);
- ADDENTRY (0, 3, 0, 3, 1, 0, HPW-1, 0, 0);
- ADDENTRY (3, 3, 0, 3, 1, 0, HBP +(VIDEO_COLS * 2) + 72 , 1, 0);
-/*
- * Odd field
- */
- ADDENTRY (0, 3, 0, 3, 1, 0, 2, 0, 0);
- ADDENTRY (0, 0, 0, 3, 1, 0, HPW, 0, 0);
- ADDENTRY (3, 0, 0, 3, 1, 0, HBP + (VIDEO_COLS * 2) + 72, 0, 0);
-
- ADDENTRY (0, 0, 0, 3, 1, 0, VPW+1, 1, 0);
- ADDENTRY (0, 0, 0, 3, 1, 0, HPW-1, 0, 0);
- ADDENTRY (3, 0, 0, 3, 1, 0, HBP + (VIDEO_COLS * 2) + 72, 1, 0);
-
- ADDENTRY (0, 3, 0, 3, 1, 0, VBP, 1, 0);
- ADDENTRY (0, 3, 0, 3, 1, 0, HPW-1, 0, 0);
- ADDENTRY (3, 3, 0, 3, 1, 0, HBP + (VIDEO_COLS * 2) + 72, 1, 0);
-/*
- * Active area
- */
- ADDENTRY (0, 3, 0, 3, 1, 0, VID_R , 1, 0);
- ADDENTRY (0, 3, 0, 3, 1, 0, HPW-1, 0, 0);
- ADDENTRY (3, 3, 0, 3, 1, 0, HBP, 0, 0);
- ADDENTRY (3, 3, 0, 3, 0, 0, VIDEO_COLS*2, 0, 0);
- ADDENTRY (3, 3, 0, 3, 1, 0, 72, 1, 1);
-
- ADDENTRY (0, 3, 0, 3, 1, 0, 51, 1, 0);
- ADDENTRY (0, 3, 0, 3, 1, 0, HPW-1, 0, 0);
- ADDENTRY (3, 3, 0, 3, 1, 0, HBP +(VIDEO_COLS * 2) + 72 , 1, 0);
-
- debug ("done\n");
-
-#else /* !CONFIG_RRVISION */
-
/*
* Hx Vx Fx Bx VDS INT LCYC LP LST
*
* one more cycle loop and a last identifier)
*/
video_mode_dupefield (vr, &vr[entry], entry);
-#endif /* CONFIG_RRVISION */
#endif /* VIDEO_MODE_PAL */
static void video_encoder_init (void)
{
-#ifdef VIDEO_I2C
- int rc;
-
- /* Initialize the I2C */
- debug ("[VIDEO ENCODER] Initializing I2C bus...\n");
-#ifdef CONFIG_SYS_I2C
- i2c_init_all();
-#else
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-#endif
-
- /* Send configuration */
-#ifdef DEBUG
- {
- int i;
-
- puts ("[VIDEO ENCODER] Configuring the encoder...\n");
-
- printf ("Sending %zu bytes (@ %08lX) to I2C 0x%lX:\n ",
- sizeof(video_encoder_data),
- (ulong)video_encoder_data,
- (ulong)VIDEO_I2C_ADDR);
- for (i=0; i<sizeof(video_encoder_data); ++i) {
- printf(" %02X", video_encoder_data[i]);
- }
- putc ('\n');
- }
-#endif /* DEBUG */
-
- if ((rc = i2c_write (VIDEO_I2C_ADDR, 0, 1,
- video_encoder_data,
- sizeof(video_encoder_data))) != 0) {
- printf ("i2c_send error: rc=%d\n", rc);
- return;
- }
-#endif /* VIDEO_I2C */
return;
}
immap->im_ioport.iop_pdpar = 0x1fff;
immap->im_ioport.iop_pddir = 0x0000;
-#ifdef CONFIG_RRVISION
- debug ("PC5->Output(1): enable PAL clock");
- immap->im_ioport.iop_pcpar &= ~(0x0400);
- immap->im_ioport.iop_pcdir |= 0x0400 ;
- immap->im_ioport.iop_pcdat |= 0x0400 ;
- debug ("PDPAR=0x%04X PDDIR=0x%04X PDDAT=0x%04X\n",
- immap->im_ioport.iop_pdpar,
- immap->im_ioport.iop_pddir,
- immap->im_ioport.iop_pddat);
- debug ("PCPAR=0x%04X PCDIR=0x%04X PCDAT=0x%04X\n",
- immap->im_ioport.iop_pcpar,
- immap->im_ioport.iop_pcdir,
- immap->im_ioport.iop_pcdat);
-#endif /* CONFIG_RRVISION */
-
/* Blanking the screen. */
debug ("[VIDEO CTRL] Blanking the screen...\n");
video_fill (VIDEO_BG_COL);
+++ /dev/null
-if TARGET_RRVISION
-
-config SYS_BOARD
- default "RRvision"
-
-config SYS_CONFIG_NAME
- default "RRvision"
-
-endif
+++ /dev/null
-RRVISION BOARD
-M: Wolfgang Denk <wd@denx.de>
-S: Maintained
-F: board/RRvision/
-F: include/configs/RRvision.h
-F: configs/RRvision_defconfig
-F: configs/RRvision_LCD_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = RRvision.o flash.o
+++ /dev/null
-/*
- * (C) Copyright 2001-2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-/* ------------------------------------------------------------------------- */
-
-static long int dram_size (long int, long int *, long int);
-
-/* ------------------------------------------------------------------------- */
-
-#define _NOT_USED_ 0xFFFFFFFF
-
-const uint sdram_table[] =
-{
- /*
- * Single Read. (Offset 0 in UPMA RAM)
- */
- 0x1F07FC04, 0xEEAEFC04, 0x11ADFC04, 0xEFBBBC00,
- 0x1FF77C47, /* last */
- /*
- * SDRAM Initialization (offset 5 in UPMA RAM)
- *
- * This is no UPM entry point. The following definition uses
- * the remaining space to establish an initialization
- * sequence, which is executed by a RUN command.
- *
- */
- 0x1FF77C34, 0xEFEABC34, 0x1FB57C35, /* last */
- /*
- * Burst Read. (Offset 8 in UPMA RAM)
- */
- 0x1F07FC04, 0xEEAEFC04, 0x10ADFC04, 0xF0AFFC00,
- 0xF0AFFC00, 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Single Write. (Offset 18 in UPMA RAM)
- */
- 0x1F07FC04, 0xEEAEBC00, 0x01B93C04, 0x1FF77C47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Burst Write. (Offset 20 in UPMA RAM)
- */
- 0x1F07FC04, 0xEEAEBC00, 0x10AD7C00, 0xF0AFFC00,
- 0xF0AFFC00, 0xE1BBBC04, 0x1FF77C47, /* last */
- _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Refresh (Offset 30 in UPMA RAM)
- */
- 0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC84, 0xFFFFFC07, /* last */
- _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Exception. (Offset 3c in UPMA RAM)
- */
- 0x7FFFFC07, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_,
-};
-
-/* ------------------------------------------------------------------------- */
-
-
-/*
- * Check Board Identity:
- *
- * Always return 1 (no second DRAM bank).
- */
-
-int checkboard (void)
-{
- char buf[64];
- int i;
- int l = getenv_f("serial#", buf, sizeof(buf));
-
- puts ("Board: RRvision ");
-
- for (i=0; i < l; ++i) {
- if (buf[i] == ' ')
- break;
- putc (buf[i]);
- }
-
- putc ('\n');
-
- return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- unsigned long reg;
- long int size8, size9;
- long int size = 0;
-
- upmconfig (UPMA, (uint *)sdram_table, sizeof(sdram_table) / sizeof(uint));
-
- /*
- * Preliminary prescaler for refresh (depends on number of
- * banks): This value is selected for four cycles every 62.4 us
- * with two SDRAM banks or four cycles every 31.2 us with one
- * bank. It will be adjusted after memory sizing.
- */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
-
- memctl->memc_mar = 0x00000088;
-
- /*
- * Map controller bank 1 the SDRAM bank 2 at physical address 0.
- */
- memctl->memc_or1 = CONFIG_SYS_OR2_PRELIM;
- memctl->memc_br1 = CONFIG_SYS_BR2_PRELIM;
-
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
-
- udelay (200);
-
- /* perform SDRAM initializsation sequence */
-
- memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */
- udelay (1);
- memctl->memc_mcr = 0x80002230; /* SDRAM bank 0 - execute twice */
- udelay (1);
-
- memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
-
- udelay (1000);
-
- /*
- * Check Bank 0 Memory Size
- *
- * try 8 column mode
- */
- size8 = dram_size (CONFIG_SYS_MAMR_8COL,
- SDRAM_BASE2_PRELIM,
- SDRAM_MAX_SIZE);
-
- udelay (1000);
-
- /*
- * try 9 column mode
- */
- size9 = dram_size (CONFIG_SYS_MAMR_9COL,
- SDRAM_BASE2_PRELIM,
- SDRAM_MAX_SIZE);
-
- if (size8 < size9) { /* leave configuration at 9 columns */
- size = size9;
-/* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
- } else { /* back to 8 columns */
- size = size8;
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
- udelay (500);
-/* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
- }
-
- udelay (1000);
-
- /*
- * Adjust refresh rate depending on SDRAM type
- * For types > 128 MBit leave it at the current (fast) rate
- */
- if (size < 0x02000000) {
- /* reduce to 15.6 us (62.4 us / quad) */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
- udelay (1000);
- }
-
- /*
- * Final mapping
- */
- memctl->memc_or1 = ((-size) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
- memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
-
- /*
- * No bank 1
- *
- * invalidate bank
- */
- memctl->memc_br3 = 0;
-
- /* adjust refresh rate depending on SDRAM type, one bank */
- reg = memctl->memc_mptpr;
- reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
- memctl->memc_mptpr = reg;
-
- udelay (10000);
-
- return (size);
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check memory range for valid RAM. A simple memory test determines
- * the actually available RAM size between addresses `base' and
- * `base + maxsize'. Some (not all) hardware errors are detected:
- * - short between address lines
- * - short between data lines
- */
-
-static long int dram_size (long int mamr_value, long int *base,
- long int maxsize)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- memctl->memc_mamr = mamr_value;
-
- return (get_ram_size(base, maxsize));
-}
+++ /dev/null
-/*
- * (C) Copyright 2000-2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define DEBUG
-
-#include <common.h>
-#include <mpc8xx.h>
-
-#ifndef CONFIG_ENV_ADDR
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-#endif
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- unsigned long size;
- int i;
-
- /* Init: no FLASHes known */
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- /* Static FLASH Bank configuration here - FIXME XXX */
-
- size = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
- size, size<<20);
- }
-
- /* Remap FLASH according to real size */
- memctl->memc_or0 = CONFIG_SYS_OR_TIMING_FLASH | (-size & OR_AM_MSK);
- memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_MS_GPCM | BR_V;
-
- /* Re-do sizing to get full correct info */
- size = flash_get_size((vu_long *)CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SIZE-1,
- &flash_info[0]);
-#endif
-
- flash_info[0].size = size;
-
- return (size);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- puts ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD: puts ("AMD "); break;
- case FLASH_MAN_FUJ: puts ("FUJITSU "); break;
- default: puts ("Unknown Vendor "); break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM400B: puts ("AM29LV400B (4 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM400T: puts ("AM29LV400T (4 Mbit, top boot sector)\n");
- break;
- case FLASH_AM800B: puts ("AM29LV800B (8 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM800T: puts ("AM29LV800T (8 Mbit, top boot sector)\n");
- break;
- case FLASH_AM160B: puts ("AM29LV160B (16 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM160T: puts ("AM29LV160T (16 Mbit, top boot sector)\n");
- break;
- case FLASH_AM320B: puts ("AM29LV320B (32 Mbit, bottom boot sect)\n");
- break;
- case FLASH_AM320T: puts ("AM29LV320T (32 Mbit, top boot sector)\n");
- break;
- default: puts ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- puts (" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- puts ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- puts ("\n");
- return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
- short i;
- ulong value;
- ulong base = (ulong)addr;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x0555] = 0x00AA00AA;
- addr[0x02AA] = 0x00550055;
- addr[0x0555] = 0x00900090;
-
- value = addr[0];
-
- switch (value) {
- case AMD_MANUFACT:
- info->flash_id = FLASH_MAN_AMD;
- break;
- case FUJ_MANUFACT:
- info->flash_id = FLASH_MAN_FUJ;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- return (0); /* no or unknown flash */
- }
-
- value = addr[1]; /* device ID */
-
- switch (value) {
- case AMD_ID_LV400T:
- info->flash_id += FLASH_AM400T;
- info->sector_count = 11;
- info->size = 0x00100000;
- break; /* => 1 MB */
-
- case AMD_ID_LV400B:
- info->flash_id += FLASH_AM400B;
- info->sector_count = 11;
- info->size = 0x00100000;
- break; /* => 1 MB */
-
- case AMD_ID_LV800T:
- info->flash_id += FLASH_AM800T;
- info->sector_count = 19;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- case AMD_ID_LV800B:
- info->flash_id += FLASH_AM800B;
- info->sector_count = 19;
- info->size = 0x00200000;
- break; /* => 2 MB */
-
- case AMD_ID_LV160T:
- info->flash_id += FLASH_AM160T;
- info->sector_count = 35;
- info->size = 0x00400000;
- break; /* => 4 MB */
-
- case AMD_ID_LV160B:
- info->flash_id += FLASH_AM160B;
- info->sector_count = 35;
- info->size = 0x00400000;
- break; /* => 4 MB */
- case AMD_ID_LV320T:
- info->flash_id += FLASH_AM320T;
- info->sector_count = 71;
- info->size = 0x00800000;
- break; /* => 8 MB */
-
- case AMD_ID_LV320B:
- info->flash_id += FLASH_AM320B;
- info->sector_count = 71;
- info->size = 0x00800000;
- break; /* => 8 MB */
- default:
- info->flash_id = FLASH_UNKNOWN;
- return (0); /* => no or unknown flash */
- }
-
- /* set up sector start address table */
- switch (value) {
- case AMD_ID_LV400B:
- case AMD_ID_LV800B:
- case AMD_ID_LV160B:
- /* set sector offsets for bottom boot block type */
- info->start[0] = base + 0x00000000;
- info->start[1] = base + 0x00008000;
- info->start[2] = base + 0x0000C000;
- info->start[3] = base + 0x00010000;
- for (i = 4; i < info->sector_count; i++) {
- info->start[i] = base + (i * 0x00020000) - 0x00060000;
- }
- break;
- case AMD_ID_LV400T:
- case AMD_ID_LV800T:
- case AMD_ID_LV160T:
- /* set sector offsets for top boot block type */
- i = info->sector_count - 1;
- info->start[i--] = base + info->size - 0x00008000;
- info->start[i--] = base + info->size - 0x0000C000;
- info->start[i--] = base + info->size - 0x00010000;
- for (; i >= 0; i--) {
- info->start[i] = base + i * 0x00020000;
- }
- break;
- case AMD_ID_LV320B:
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base;
- /*
- * The first 8 sectors are 8 kB,
- * all the other ones are 64 kB
- */
- base += (i < 8)
- ? 2 * ( 8 << 10)
- : 2 * (64 << 10);
- }
- break;
- case AMD_ID_LV320T:
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base;
- /*
- * The last 8 sectors are 8 kB,
- * all the other ones are 64 kB
- */
- base += (i < (info->sector_count - 8))
- ? 2 * (64 << 10)
- : 2 * ( 8 << 10);
- }
- break;
- default:
- return (0);
- break;
- }
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr = (volatile unsigned long *)(info->start[i]);
- info->protect[i] = addr[2] & 1;
- }
-
- /*
- * Prevent writes to uninitialized FLASH.
- */
- if (info->flash_id != FLASH_UNKNOWN) {
- addr = (volatile unsigned long *)info->start[0];
-
- *addr = 0x00F000F0; /* reset bank */
- }
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- vu_long *addr = (vu_long*)(info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- puts ("- missing\n");
- } else {
- puts ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id == FLASH_UNKNOWN) ||
- (info->flash_id > FLASH_AMD_COMP)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- puts ("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0x00AA00AA;
- addr[0x02AA] = 0x00550055;
- addr[0x0555] = 0x00800080;
- addr[0x0555] = 0x00AA00AA;
- addr[0x02AA] = 0x00550055;
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (vu_long*)(info->start[sect]);
- addr[0] = 0x00300030;
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer (0);
- last = start;
- addr = (vu_long*)(info->start[l_sect]);
- while ((addr[0] & 0x00800080) != 0x00800080) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- puts ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
-DONE:
- /* reset to read mode */
- addr = (volatile unsigned long *)info->start[0];
- addr[0] = 0x00F000F0; /* reset bank */
-
- puts (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i=0, cp=wp; i<l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
- for (; i<4 && cnt>0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt==0 && i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i=0; i<4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
- vu_long *addr = (vu_long*)(info->start[0]);
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*((vu_long *)dest) & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0x00AA00AA;
- addr[0x02AA] = 0x00550055;
- addr[0x0555] = 0x00A000A0;
-
- *((vu_long *)dest) = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
- while ((*((vu_long *)dest) & 0x00800080) != (data & 0x00800080)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
+++ /dev/null
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- . = env_offset;
- common/env_embedded.o (.ppcenv)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
+++ /dev/null
-/*
- * (C) Copyright 2003 Wolfgang Grandegger <wg@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define VIDEO_ENCODER_NAME "Analog Devices AD7179"
-
-#define VIDEO_ENCODER_I2C_RATE 100000 /* Max rate is 100Khz */
-#define VIDEO_ENCODER_CB_Y_CR_Y /* Use CB Y CR Y format... */
-
-#define VIDEO_MODE_YUYV /* The only mode supported by this encoder */
-#undef VIDEO_MODE_RGB
-#define VIDEO_MODE_BPP 16
-
-#ifdef VIDEO_MODE_PAL
-#define VIDEO_ACTIVE_COLS 720
-#define VIDEO_ACTIVE_ROWS 576
-#define VIDEO_VISIBLE_COLS 640
-#define VIDEO_VISIBLE_ROWS 480
-#else
-#error "NTSC mode is not supported"
-#endif
-
-static unsigned char video_encoder_data[] = {
- 0x05, /* Mode Register 0 */
- 0x11, /* Mode Register 1 */
- 0x20, /* Mode Register 2 */
- 0x0C, /* Mode Register 3 */
- 0x01, /* Mode Register 4 */
- 0x00, /* Reserved */
- 0x00, /* Reserved */
- 0x04, /* Timing Register 0 */
- 0x00, /* Timing Register 1 */
- 0xCB, /* Subcarrier Frequency Register 0 */
- 0x0A, /* Subcarrier Frequency Register 1 */
- 0x09, /* Subcarrier Frequency Register 2 */
- 0x2A, /* Subcarrier Frequency Register 3 */
- 0x00, /* Subcarrier Phase */
- 0x00, /* Closed Captioning Ext Reg 0 */
- 0x00, /* Closed Captioning Ext Reg 1 */
- 0x00, /* Closed Captioning Reg 0 */
- 0x00, /* Closed Captioning Reg 1 */
- 0x00, /* Pedestal Control Reg 0 */
- 0x00, /* Pedestal Control Reg 1 */
- 0x00, /* Pedestal Control Reg 2 */
- 0x00, /* Pedestal Control Reg 3 */
- 0x00, /* CGMS_WSS Reg 0 */
- 0x00, /* CGMS_WSS Reg 0 */
- 0x00, /* CGMS_WSS Reg 0 */
- 0x00 /* Teletext Req. Control Reg */
-} ;
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="LCD,SHARP_LQ104V7DS01"
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_RRVISION=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_RRVISION=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+RRvision powerpc mpc8xx - - Wolfgang Denk <wd@denx.de>
SPD823TS powerpc mpc8xx - - Wolfgang Denk <wd@denx.de>
KUP4K powerpc mpc8xx - - Klaus Heydeck <heydeck@kieback-peter.de>
KUP4X powerpc mpc8xx - - Klaus Heydeck <heydeck@kieback-peter.de>
r360_i2c_lcd_write(0x40 | ((ctr>>8) & 0xF), ctr & 0xFF);
}
#endif /* CONFIG_R360MPI */
-#ifdef CONFIG_RRVISION
- debug ("PC4->Output(1): enable LVDS\n");
- debug ("PC5->Output(0): disable PAL clock\n");
- immr->im_ioport.iop_pddir |= 0x1000;
- immr->im_ioport.iop_pcpar &= ~(0x0C00);
- immr->im_ioport.iop_pcdir |= 0x0C00 ;
- immr->im_ioport.iop_pcdat |= 0x0800 ;
- immr->im_ioport.iop_pcdat &= ~(0x0400);
- debug ("PDPAR=0x%04X PDDIR=0x%04X PDDAT=0x%04X\n",
- immr->im_ioport.iop_pdpar,
- immr->im_ioport.iop_pddir,
- immr->im_ioport.iop_pddat);
- debug ("PCPAR=0x%04X PCDIR=0x%04X PCDAT=0x%04X\n",
- immr->im_ioport.iop_pcpar,
- immr->im_ioport.iop_pcdir,
- immr->im_ioport.iop_pcdat);
-#endif
}
/************************************************************************/
#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
defined(CONFIG_R360MPI) || \
- defined(CONFIG_RRVISION)|| defined(CONFIG_TQM823L) || \
+ defined(CONFIG_TQM823L) || \
defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
- defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D) || \
- defined(CONFIG_RRVISION)
+ defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D)
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC2 use.
+++ /dev/null
-/*
- * (C) Copyright 2000, 2001, 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
-#define CONFIG_RRVISION 1 /* ...on a RRvision board */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-#define CONFIG_8xx_GCLK_FREQ 64000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
-#define CONFIG_PREBOOT "setenv stdout serial"
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_ETHADDR 00:50:C2:00:E0:70
-#define CONFIG_OVERWRITE_ETHADDR_ONCE 1
-#define CONFIG_IPADDR 10.0.0.5
-#define CONFIG_SERVERIP 10.0.0.2
-#define CONFIG_NETMASK 255.0.0.0
-#define CONFIG_ROOTPATH "/opt/eldk/ppc_8xx"
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}" \
- ":${gatewayip}:${netmask}:${hostname}:${netdev}:off\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "load=tftp 100000 /tftpboot/u-boot.bin\0" \
- "update=protect off 1:0-8;era 1:0-8;" \
- "cp.b 100000 40000000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "kernel_addr=40040000\0" \
- "ramdisk_addr=40100000\0" \
- "kernel_img=/tftpboot/uImage\0" \
- "kernel_load=tftp 200000 ${kernel_img}\0" \
- "net_nfs=run kernel_load nfsargs addip addtty;bootm\0" \
- "flash_nfs=run nfsargs addip addtty;bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0"
-
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#undef CONFIG_STATUS_LED /* disturbs display */
-
-#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-
-
-#ifdef CONFIG_LCD
-#define CONFIG_MPC8XX_LCD
-#else
-#define CONFIG_VIDEO 1 /* To enable the video initialization */
-
-/* Video related */
-#define CONFIG_VIDEO_LOGO 1 /* Show the logo */
-#define CONFIG_VIDEO_ENCODER_AD7179 1 /* Enable this encoder */
-#define CONFIG_VIDEO_ENCODER_AD7179_ADDR 0x2A /* ALSB to ground */
-#endif
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL 0x00000020 /* PB 26 */
-#define PB_SDA 0x00000010 /* PB 27 */
-
-#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
-#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
-#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY udelay(1) /* 1/4 I2C clock duration */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_DATE
-
-#undef CONFIG_CMD_PCMCIA
-#undef CONFIG_CMD_IDE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-
-/* timeout values are in ticks = ms */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (120*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT (1 * CONFIG_SYS_HZ) /* Timeout for Flash Write */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#else /* we must activate GPL5 in the SIUMCR for CAN */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-#endif /* CONFIG_CAN_DRIVER */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-
-/* for 64 MHz, we use a 16 MHz clock * 4 */
-#define CONFIG_SYS_PLPRCR ( (4-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_RTSEL | SCCR_RTDIV | \
- SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
- SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-/*#define CONFIG_SYS_DER 0x2002000F*/
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/*
- * FLASH timing:
- */
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_3_CLK | OR_EHTR | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#ifndef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
-#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
-#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
- BR_PS_8 | BR_MS_UPMB | BR_V )
-#endif /* CONFIG_CAN_DRIVER */
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock!)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- *
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider = 98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-#define CONFIG_SYS_MAMR_PTA 129
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _VIDEO_AD7176_H_
-#define _VIDEO_AD7176_H_
-
-#define VIDEO_ENCODER_NAME "Analog Devices AD7176"
-
-#define VIDEO_ENCODER_I2C_RATE 100000 /* Max rate is 100 kHz */
-#define VIDEO_ENCODER_CB_Y_CR_Y /* Use CB Y CR Y format... */
-
-#define VIDEO_MODE_YUYV /* The only mode supported by this encoder */
-#undef VIDEO_MODE_RGB
-#define VIDEO_MODE_BPP 16
-
-#ifdef VIDEO_MODE_PAL
-#define VIDEO_ACTIVE_COLS 720
-#define VIDEO_ACTIVE_ROWS 576
-#define VIDEO_VISIBLE_COLS 640
-#define VIDEO_VISIBLE_ROWS 480
-#endif
-
-#ifdef VIDEO_MODE_NTSC
-#define VIDEO_ACTIVE_COLS 720
-#define VIDEO_ACTIVE_ROWS 525
-#define VIDEO_VISIBLE_COLS 640
-#define VIDEO_VISIBLE_ROWS 400
-#endif
-
-static unsigned char video_encoder_data[] = {
-#ifdef VIDEO_MODE_NTSC
- 0x04, /* Mode Register 0 */
-#ifdef VIDEO_DEBUG_COLORBARS
- 0x82,
-#else
- 0x02, /* Mode Register 1 */
-#endif /* VIDEO_DEBUG_COLORBARS */
- 0x16, /* Subcarrier Freq 0 */
- 0x7c, /* Subcarrier Freq 1 */
- 0xf0, /* Subcarrier Freq 2 */
- 0x21, /* Subcarrier Freq 3 */
- 0x00, /* Subcarrier phase */
- 0x02, /* Timing Register 0 */
- 0x00, /* Extended Captioning 0 */
- 0x00, /* Extended Captioning 1 */
- 0x00, /* Closed Captioning 0 */
- 0x00, /* Closed Captioning 1 */
- 0x00, /* Timing Register 1 */
- 0x08, /* Mode Register 2 */
- 0x00, /* Pedestal Register 0 */
- 0x00, /* Pedestal Register 1 */
- 0x00, /* Pedestal Register 2 */
- 0x00, /* Pedestal Register 3 */
- 0x00 /* Mode Register 3 */
-
-#endif /* VIDEO_MODE_NTSC */
-
-#ifdef VIDEO_MODE_PAL
- 0x05, /* Mode Register 0 */
-#ifdef VIDEO_DEBUG_COLORBARS
- 0x82,
-#else
- 0x02, /* Mode Register 1 (2) */
-#endif /* VIDEO_DEBUG_COLORBARS */
- 0xcb, /* Subcarrier Freq 0 */
- 0x8a, /* Subcarrier Freq 1 */
- 0x09, /* Subcarrier Freq 2 */
- 0x2a, /* Subcarrier Freq 3 */
- 0x00, /* Subcarrier phase */
- 0x0a, /* Timing Register 0 (a) */
- 0x00, /* Extended Captioning 0 */
- 0x00, /* Extended Captioning 1 */
- 0x00, /* Closed Captioning 0 */
- 0x00, /* Closed Captioning 1 */
- 0x00, /* Timing Register 1 */
- 0x08, /* Mode Register 2 (8) */
- 0x00, /* Pedestal Register 0 */
- 0x00, /* Pedestal Register 1 */
- 0x00, /* Pedestal Register 2 */
- 0x00, /* Pedestal Register 3 */
- 0x00 /* Mode Register 3 */
-#endif /* VIDEO_MODE_PAL */
-} ;
-
-#endif /* _VIDEO_AD7176_H_ */
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _VIDEO_AD7177_H_
-#define _VIDEO_AD7177_H_
-
-/* #define VIDEO_DEBUG_DISABLE_COLORS 0 */
-
-#define VIDEO_ENCODER_NAME "Analog Devices AD7177"
-
-#define VIDEO_ENCODER_I2C_RATE 100000 /* Max rate is 100 kHz */
-#define VIDEO_ENCODER_CB_Y_CR_Y /* Use CB Y CR Y format... */
-
-#define VIDEO_MODE_YUYV /* The only mode supported by this encoder */
-#undef VIDEO_MODE_RGB
-#define VIDEO_MODE_BPP 16
-
-#ifdef VIDEO_MODE_PAL
-#define VIDEO_ACTIVE_COLS 720
-#define VIDEO_ACTIVE_ROWS 576
-#define VIDEO_VISIBLE_COLS 640
-#define VIDEO_VISIBLE_ROWS 480
-#endif
-
-#ifdef VIDEO_MODE_NTSC
-#define VIDEO_ACTIVE_COLS 720
-#define VIDEO_ACTIVE_ROWS 525
-#define VIDEO_VISIBLE_COLS 640
-#define VIDEO_VISIBLE_ROWS 400
-#endif
-
-static unsigned char
- video_encoder_data[] = {
-#ifdef VIDEO_MODE_NTSC
- 0x04, /* Mode Register 0 */
-#ifdef VIDEO_DEBUG_COLORBARS
- 0xc2,
-#else
- 0x42, /* Mode Register 1 */
-#endif /* VIDEO_DEBUG_COLORBARS */
- 0x16, /* Subcarrier Freq 0 */
- 0x7c, /* Subcarrier Freq 1 */
- 0xf0, /* Subcarrier Freq 2 */
- 0x21, /* Subcarrier Freq 3 */
- 0x00, /* Subcarrier phase */
- 0x02, /* Timing Register 0 */
- 0x00, /* Extended Captioning 0 */
- 0x00, /* Extended Captioning 1 */
- 0x00, /* Closed Captioning 0 */
- 0x00, /* Closed Captioning 1 */
- 0x00, /* Timing Register 1 */
- 0x08, /* Mode Register 2 */
- 0x00, /* Pedestal Register 0 */
- 0x00, /* Pedestal Register 1 */
- 0x00, /* Pedestal Register 2 */
- 0x00, /* Pedestal Register 3 */
- 0x08, /* Mode Register 3 */
-
-#endif /* VIDEO_MODE_NTSC */
-
-#ifdef VIDEO_MODE_PAL
-#ifdef VIDEO_MODE_RGB_OUT
-
- 0x69, /* Mode Register 0 */
-#ifdef VIDEO_DEBUG_COLORBARS
- 0xc0, /* Mode Register 1 (c0) */
-#else
- 0x40, /* Mode Register 1 (c0) */
-#endif /* VIDEO_DEBUG_COLORBARS */
- 0xcb, /* Subcarrier Freq 0 */
- 0x8a, /* Subcarrier Freq 1 */
- 0x09, /* Subcarrier Freq 2 */
- 0x2a, /* Subcarrier Freq 3 */
- 0x00, /* Subcarrier phase */
- 0x02, /* Timing Register 0 */
- 0x00, /* Extended Captioning 0 */
- 0x00, /* Extended Captioning 1 */
- 0x00, /* Closed Captioning 0 */
- 0x00, /* Closed Captioning 1 */
- 0x00, /* Timing Register 1 */
- 0x28, /* Mode Register 2 */
- 0x00, /* Pedestal Register 0 */
- 0x00, /* Pedestal Register 1 */
- 0x00, /* Pedestal Register 2 */
- 0x00, /* Pedestal Register 3 */
- 0x08, /* Mode Register 3 */
-
-#else /* ! VIDEO_MODE_RGB_OUT */
-
- 0x09, /* Mode Register 0 (was 01) */
-#ifdef VIDEO_DEBUG_COLORBARS
- 0xd8, /* */
-#else
- 0x59, /* Mode Register 1 (was 58) */
-#endif /* VIDEO_DEBUG_COLORBARS */
- 0xcb, /* Subcarrier Freq 0 */
- 0x8a, /* Subcarrier Freq 1 */
- 0x09, /* Subcarrier Freq 2 */
- 0x2a, /* Subcarrier Freq 3 */
- 0x00, /* Subcarrier phase */
- 0x02, /* Timing Register 0 (was a) */
- 0x00, /* Extended Captioning 0 */
- 0x00, /* Extended Captioning 1 */
- 0x00, /* Closed Captioning 0 */
- 0x00, /* Closed Captioning 1 */
- 0x00, /* Timing Register 1 */
-#ifdef VIDEO_DEBUG_LOWPOWER
-#ifdef VIDEO_DEBUG_DISABLE_COLORS
- 0x98, /* Mode Register 2 */
-#else
- 0x88, /* Mode Register 2 */
-#endif /* VIDEO_DEBUG_DISABLE_COLORS */
-#else /* ! VIDEO_DEBUG_LOWPOWER */
-#ifdef VIDEO_DEBUG_DISABLE_COLORS
- 0x18, /* Mode Register 2 */
-#else
- 0x08, /* Mode Register 2 */
-#endif /* VIDEO_DEBUG_DISABLE_COLORS */
-#endif /* VIDEO_DEBUG_LOWPOWER */
- 0x00, /* Pedestal Register 0 */
- 0x00, /* Pedestal Register 1 */
- 0x00, /* Pedestal Register 2 */
- 0x00, /* Pedestal Register 3 */
- 0x08 /* Mode Register 3 */
-#endif /* VIDEO_MODE_RGB_OUT */
-#endif /* VIDEO_MODE_PAL */
- } ;
-
-#endif /* _VIDEO_AD7177_H_ */
+++ /dev/null
-/*
- * (C) Copyright 2003 Wolfgang Grandegger <wg@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _VIDEO_AD7179_H_
-#define _VIDEO_AD7179_H_
-
-/*
- * The video encoder data are board specific now!
- */
-
-#if defined(CONFIG_RRVISION)
-#include "../board/RRvision/video_ad7179.h"
-#else
-#error "Please provide a board-specific video_ad7179.h"
-#endif
-
-#endif /* _VIDEO_AD7179_H_ */
projects / u-boot.git / commitdiff