Changes for U-Boot 1.1.3:
======================================================================
+* Patch by Detlev Zundel, 31 Mar 2005:
+ Cleanup duplicate definition of overwrite_console()
+
+* Update TQM5200 configuration;
+ prepare for Rev. 200 starter kit boards
+
* Patch by Scott McNutt, 21 Oct 2004:
Add support for Nios-II EPCS Controller core.
*/
#ifdef CFG_CONSOLE_OVERWRITE_ROUTINE
extern int overwrite_console (void);
+#define OVERWRITE_CONSOLE overwrite_console ()
#else
-int overwrite_console (void)
-{
- return (0);
-}
+#define OVERWRITE_CONSOLE 0
#endif /* CFG_CONSOLE_OVERWRITE_ROUTINE */
#endif /* CFG_CONSOLE_IS_IN_ENV */
stdoutname = getenv ("stdout");
stderrname = getenv ("stderr");
- if (overwrite_console () == 0) { /* if not overwritten by config switch */
+ if (OVERWRITE_CONSOLE == 0) { /* if not overwritten by config switch */
inputdev = search_device (DEV_FLAGS_INPUT, stdinname);
outputdev = search_device (DEV_FLAGS_OUTPUT, stdoutname);
errdev = search_device (DEV_FLAGS_OUTPUT, stderrname);
#ifdef CFG_CONSOLE_OVERWRITE_ROUTINE
extern int overwrite_console (void);
+#define OVERWRITE_CONSOLE overwrite_console ()
#else
-int overwrite_console (void)
-{
- return (0);
-}
-#endif
+#define OVERWRITE_CONSOLE 0
+#endif /* CFG_CONSOLE_OVERWRITE_ROUTINE */
int kbd_init (void)
{
/* check if this is the standard input device */
if(strcmp(stdinname,DEVNAME)==0) {
/* reassign the console */
- if(overwrite_console()) {
+ if(OVERWRITE_CONSOLE) {
return 1;
}
error=console_assign(stdin,DEVNAME);
#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
#define CONFIG_STK52XX 1 /* ... on a STK52XX base board */
+#define CONFIG_STK52XX_REV100 1 /* define for revision 100 baseboards */
#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define CONFIG_EEPRO100 1
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
+#endif /* CONFIG_STK52XX */
#ifdef CONFIG_PCI
#define ADD_PCI_CMD CFG_CMD_PCI
#define CONFIG_CONSOLE_EXTRA_INFO
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_SPLASH_SCREEN
+#define CFG_CONSOLE_IS_IN_ENV
#endif
#ifdef CONFIG_VIDEO
* Bit 0 (mask: 0x80000000): 1
* use ALT CAN position: Bits 2-3 (mask: 0x30000000):
* 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
- * Set for rev 100 modules with an onboard EEPROM (because,
- * there I2C1 is used as I2C bus)
* 01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
- * Set for rev 200 modules
+ * Use for REV200 STK52XX boards. Do not use with REV100 modules
+ * (because, there I2C1 is used as I2C bus)
* use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
+ * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
+ * 000 -> All PSC2 pins are GIOPs
+ * 001 -> CAN1/2 on PSC2 pins
+ * Use for REV100 STK52xx boards
* use PSC6:
* on STK52xx:
* use as UART. Pins PSC6_0 to PSC6_3 are used.
#if defined (CONFIG_MINIFAP)
# define CFG_GPS_PORT_CONFIG 0x91000004
#elif defined (CONFIG_STK52XX)
-# if defined (CONFIG_TQM5200_REV100)
-# define CFG_GPS_PORT_CONFIG 0x81500004
-# else
-# define CFG_GPS_PORT_CONFIG 0x91500004
+# if defined (CONFIG_STK52XX_REV100)
+# define CFG_GPS_PORT_CONFIG 0x81500014
+# else /* STK52xx REV200 and above */
+# if defined (CONFIG_TQM5200_REV100)
+# error TQM5200 REV100 not supported on STK52XX REV200 or above
+# else/* TQM5200 REV200 and above */
+# define CFG_GPS_PORT_CONFIG 0x91500004
+# endif
# endif
-#else /* TMQ5200_IP */
+#else /* TMQ5200 Inbetriebnahme-Board */
# define CFG_GPS_PORT_CONFIG 0x81000004
#endif