Changes for U-Boot 1.0.0:
======================================================================
+* Patches by Jon Diekema, 15 Sep 2003:
+ - add description for missing CFG_CMD_* entries in the README file
+ - sacsng tweaks
+
* Patch by Gleb Natapov, 14 Sep 2003:
enable watchdog support for all MPC824x boards that have a watchdog
#define enables commands:
-------------------------
CFG_CMD_ASKENV * ask for env variable
+ CFG_CMD_AUTOSCRIPT Autoscript Support
CFG_CMD_BDI bdinfo
CFG_CMD_BEDBUG Include BedBug Debugger
+ CFG_CMD_BMP * BMP support
CFG_CMD_BOOTD bootd
CFG_CMD_CACHE icache, dcache
CFG_CMD_CONSOLE coninfo
CFG_CMD_DATE * support for RTC, date/time...
CFG_CMD_DHCP DHCP support
+ CFG_CMD_DIAG * Diagnostics
+ CFG_CMD_DOC * Disk-On-Chip Support
+ CFG_CMD_DTT Digital Therm and Thermostat
CFG_CMD_ECHO * echo arguments
CFG_CMD_EEPROM * EEPROM read/write support
CFG_CMD_ELF bootelf, bootvx
CFG_CMD_FDOS * Dos diskette Support
CFG_CMD_FLASH flinfo, erase, protect
CFG_CMD_FPGA FPGA device initialization support
+ CFG_CMD_HWFLOW * RTS/CTS hw flow control
CFG_CMD_I2C * I2C serial bus support
CFG_CMD_IDE * IDE harddisk support
CFG_CMD_IMI iminfo
+ CFG_CMD_IMLS List all found images
CFG_CMD_IMMAP * IMMR dump support
CFG_CMD_IRQ * irqinfo
+ CFG_CMD_JFFS2 * JFFS2 Support
CFG_CMD_KGDB * kgdb
CFG_CMD_LOADB loadb
CFG_CMD_LOADS loads
CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
loop, mtest
+ CFG_CMD_MISC Misc functions like sleep etc
CFG_CMD_MMC MMC memory mapped support
CFG_CMD_MII MII utility commands
+ CFG_CMD_NAND * NAND support
CFG_CMD_NET bootp, tftpboot, rarpboot
CFG_CMD_PCI * pciinfo
CFG_CMD_PCMCIA * PCMCIA support
+ CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
+ CFG_CMD_PORTIO Port I/O
CFG_CMD_REGINFO * Register dump
CFG_CMD_RUN run command in env variable
+ CFG_CMD_SAVES save S record dump
CFG_CMD_SCSI * SCSI Support
+ CFG_CMD_SDRAM * print SDRAM configuration information
CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
CFG_CMD_SPI * SPI serial bus support
CFG_CMD_USB * USB support
+ CFG_CMD_VFD * VFD support (TRAB)
CFG_CMD_BSP * Board SPecific functions
-----------------------------------------------
CFG_CMD_ALL all
#include <mpc8260.h>
#include <i2c.h>
#include <spi.h>
+#include <command.h>
#ifdef CONFIG_SHOW_BOOT_PROGRESS
#include <status_led.h>
#endif
+#ifdef CONFIG_ETHER_LOOPBACK_TEST
+extern void eth_loopback_test(void);
+#endif /* CONFIG_ETHER_LOOPBACK_TEST */
+
+extern int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+
#include "clkinit.h"
#include "ioconfig.h" /* I/O configuration table */
/* We don't trust CL less than 2 (only saw it on an old 16MByte DIMM) */
if(caslatency < 2) {
- printf("CL was %d, forcing to 2\n", caslatency);
+ printf("WARNING: CL was %d, forcing to 2\n", caslatency);
caslatency = 2;
}
if(rows > 14) {
- printf("This doesn't look good, rows = %d, should be <= 14\n", rows);
+ printf("WARNING: This doesn't look good, rows = %d, should be <= 14\n", rows);
rows = 14;
}
if(cols > 11) {
- printf("This doesn't look good, columns = %d, should be <= 11\n", cols);
+ printf("WARNING: This doesn't look good, columns = %d, should be <= 11\n", cols);
cols = 11;
}
int sample_128x; /* Use 128/4 clocking for the ADC/DAC */
int right_just; /* Is the data to the DAC right justified? */
int mclk_divide; /* MCLK Divide */
+ int quiet; /* Quiet or minimal output mode */
+
+ quiet = 0;
+ if ((ep = getenv("quiet")) != NULL) {
+ quiet = simple_strtol(ep, NULL, 10);
+ }
+ else {
+ setenv("quiet", "0");
+ }
/*
* SACSng custom initialization:
setenv("Daq128xSampling", "1");
}
- /* Display the ADC/DAC clocking information */
- Daq_Display_Clocks();
+ /*
+ * Display the ADC/DAC clocking information
+ */
+ if (!quiet) {
+ Daq_Display_Clocks();
+ }
/*
* Determine the DAC data justification
* 3) Write the I2C address to register 6
* 4) Enable address matching by setting the MSB in register 7
*/
-
- printf("Initializing the ADC...\n");
+
+ if (!quiet) {
+ printf("Initializing the ADC...\n");
+ }
udelay(ADC_INITIAL_DELAY); /* 10uSec per uF of VREF cap */
iopa->pdat &= ~ADC_SDATA1_MASK; /* release SDATA1 */
* sending an I2C "start" sequence. When we bring the I2C back to
* the normal state, we send an I2C "stop" sequence.
*/
- printf("Initializing the DAC...\n");
+ if (!quiet) {
+ printf("Initializing the DAC...\n");
+ }
/*
* Bring the I2C clock and data lines low for initialization
I2C_DELAY;
I2C_TRISTATE;
- printf("\n");
+ if (!quiet) {
+ printf("\n");
+ }
+
+#ifdef CONFIG_ETHER_LOOPBACK_TEST
+ /*
+ * Run the Ethernet loopback test
+ */
+ eth_loopback_test ();
+#endif /* CONFIG_ETHER_LOOPBACK_TEST */
#ifdef CONFIG_SHOW_BOOT_PROGRESS
/*
void show_boot_progress (int status)
{
- if(status != -1) {
+ int i,j;
+ if(status > 0) {
last_boot_progress = status;
} else {
+ /*
+ * If a specific failure code is given, flash this code
+ * else just use the last success code we've seen
+ */
+ if(status < -1)
+ last_boot_progress = -status;
+
+ /*
+ * Flash this code 5 times
+ */
+ for(j=0; j<5; j++) {
+ /*
+ * Houston, we have a problem.
+ * Blink the last OK status which indicates where things failed.
+ */
+ status_led_set(STATUS_LED_RED, STATUS_LED_ON);
+ flash_code(last_boot_progress, 5, 3);
+
+ /*
+ * Delay 5 seconds between repetitions,
+ * with the fault LED blinking
+ */
+ for(i=0; i<5; i++) {
+ status_led_set(STATUS_LED_RED, STATUS_LED_OFF);
+ udelay(500000);
+ status_led_set(STATUS_LED_RED, STATUS_LED_ON);
+ udelay(500000);
+ }
+ }
+
/*
- * Houston, we have a problem. Blink the last OK status which
- * indicates where things failed.
+ * Reset the board to retry initialization.
*/
- status_led_set(STATUS_LED_RED, STATUS_LED_ON);
- flash_code(last_boot_progress, 5, 3);
- udelay(1000000);
- status_led_set(STATUS_LED_RED, STATUS_LED_BLINKING);
+ do_reset (NULL, 0, 0, NULL);
}
}
#endif /* CONFIG_SHOW_BOOT_PROGRESS */
#ifndef __CONFIG_H
#define __CONFIG_H
-/* Enable debug prints */
#undef DEBUG /* General debug */
#undef DEBUG_BOOTP_EXT /* Debug received vendor fields */
+#undef CONFIG_LOGBUFFER /* External logbuffer support */
+
/*****************************************************************************
*
* These settings must match the way _your_ board is set up
#ifdef CONFIG_ETHER_ON_FCC
#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */
+#undef CONFIG_ETHER_LOOPBACK_TEST /* Ethernet external loopback test */
#define CONFIG_MII /* MII PHY management */
#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
/*
* will be part of the default enviroment compiled into the boot image.
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
-"serverip=192.168.123.201\0" \
+"quiet=0\0" \
+"serverip=192.168.123.205\0" \
"ipaddr=192.168.123.203\0" \
"checkhostname=VR8500\0" \
"reprog="\
+ "bootp; " \
"tftpboot 0x140000 /bdi2000/u-boot.bin; " \
"protect off 60000000 6003FFFF; " \
"erase 60000000 6003FFFF; " \
"adc-12=echo ### ADC-12 ; imd.b e 81 e\0" \
"adc-34=echo ### ADC-34 ; imd.b f 81 e\0" \
"dac=echo ### DAC ; imd.b 11 81 5\0" \
-"boot-hook=run ana\0"
+"boot-hook=echo\0"
/* What should the console's baud rate be? */
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTP_RANDOM_DELAY /* Randomize the BOOTP retry delay */
-#define CONFIG_BOOTP_RETRY_COUNT 0x40000000 /* # of timeouts before giving up */
-
/* Add support for a few extra bootp options like:
* - File size
- * - DNS
+ * - DNS (up to 2 servers)
+ * - Send hostname to DHCP server
*/
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
CONFIG_BOOTP_BOOTFILESIZE | \
- CONFIG_BOOTP_DNS)
+ CONFIG_BOOTP_DNS | \
+ CONFIG_BOOTP_DNS2 | \
+ CONFIG_BOOTP_SEND_HOSTNAME)
/* undef this to save memory */
#define CFG_LONGHELP
*/
#define CONFIG_TIMESTAMP
+/* If this variable is defined, an environment variable named "ver"
+ * is created by U-Boot showing the U-Boot version.
+ */
+#define CONFIG_VERSION_VARIABLE
+
/* What U-Boot subsytems do you want enabled? */
#ifdef CONFIG_ETHER_ON_FCC
# define CONFIG_COMMANDS (((CONFIG_CMD_DFL & ~(CFG_CMD_KGDB))) | \
CFG_CMD_SDRAM | \
CFG_CMD_REGINFO | \
CFG_CMD_IMMAP | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_PING | \
CFG_CMD_MII )
#else
# define CONFIG_COMMANDS (((CONFIG_CMD_DFL & ~(CFG_CMD_KGDB))) | \
CFG_CMD_SPI | \
CFG_CMD_SDRAM | \
CFG_CMD_REGINFO | \
- CFG_CMD_IMMAP )
+ CFG_CMD_IMMAP | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_PING )
#endif /* CONFIG_ETHER_ON_FCC */
/* Where do the internal registers live? */
#define CFG_IMMR 0xF0000000
+#undef CONFIG_WATCHDOG /* disable the watchdog */
+
/*****************************************************************************
*
* You should not have to modify any of the following settings
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
+
/*
* Miscellaneous configurable options
*/
+#define CFG_BOOTM_HEADER_QUIET 1 /* Suppress the image header dump */
+ /* in the bootm command. */
+#define CFG_BOOTM_PROGESS_QUIET 1 /* Suppress the progress displays, */
+ /* "## <message>" from the bootm cmd */
+#define CFG_BOOTP_CHECK_HOSTNAME 1 /* If checkhostname environment is */
+ /* defined, then the hostname param */
+ /* validated against checkhostname. */
+#define CFG_BOOTP_RETRY_COUNT 0x40000000 /* # of timeouts before giving up */
+#define CFG_BOOTP_SHORT_RANDOM_DELAY 1 /* Use a short random delay value */
+ /* (limited to maximum of 1024 msec) */
+#define CFG_CHK_FOR_ABORT_AT_LEAST_ONCE 1
+ /* Check for abort key presses */
+ /* at least once in dependent of the */
+ /* CONFIG_BOOTDELAY value. */
+#define CFG_CONSOLE_INFO_QUIET 1 /* Don't print console @ startup */
+#define CFG_FAULT_ECHO_LINK_DOWN 1 /* Echo the inverted Ethernet link */
+ /* state to the fault LED. */
+#define CFG_FAULT_MII_ADDR 0x02 /* MII addr of the PHY to check for */
+ /* the Ethernet link state. */
+#define CFG_STATUS_FLASH_UNTIL_TFTP_OK 1 /* Keeping the status LED flashing */
+ /* until the TFTP is successful. */
+#define CFG_STATUS_OFF_AFTER_NETBOOT 1 /* After a successful netboot, */
+ /* turn off the STATUS LEDs. */
+#define CFG_TFTP_BLINK_STATUS_ON_DATA_IN 1 /* Blink status LED based on */
+ /* incoming data. */
+#define CFG_TFTP_BLOCKS_PER_HASH 100 /* For every XX blocks, output a '#' */
+ /* to signify that tftp is moving. */
+#define CFG_TFTP_HASHES_PER_FLASH 200 /* For every '#' hashes, */
+ /* flash the status LED. */
+#define CFG_TFTP_HASHES_PER_LINE 65 /* Only output XX '#'s per line */
+ /* during the tftp file transfer. */
+#define CFG_TFTP_PROGESS_QUIET 1 /* Suppress the progress displays */
+ /* '#'s from the tftp command. */
+#define CFG_TFTP_STATUS_QUIET 1 /* Suppress the status displays */
+ /* issued during the tftp command. */
+#define CFG_TFTP_TIMEOUT_COUNT 5 /* How many timeouts TFTP will allow */
+ /* before it gives up. */
+
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
*-----------------------------------------------------------------------
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
*/
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC |\
+ SYPCR_BMT |\
+ SYPCR_PBME |\
+ SYPCR_LBME |\
+ SYPCR_SWRI |\
+ SYPCR_SWP |\
+ SYPCR_SWE)
+#else
#define CFG_SYPCR (SYPCR_SWTC |\
SYPCR_BMT |\
SYPCR_PBME |\
SYPCR_LBME |\
SYPCR_SWRI |\
SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
/*-----------------------------------------------------------------------
* TMCNTSC - Time Counter Status and Control 4-40
projects / u-boot.git / commitdiff