+++ /dev/null
-/*
- * (C) Copyright 2005-2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/************************************************************************
- * yellowstone.h - configuration for YELLOWSTONE board
- ***********************************************************************/
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_YOLLOWSTONE 1 /* Board is Yellowstone */
-#define CONFIG_440GR 1 /* Specific PPC440EP support */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-#define CONFIG_BOARD_RESET 1 /* call board_reset() */
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
-#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
-#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
-#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
-#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
-
-/*Don't change either of these*/
-#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/
-#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs*/
-/*Don't change either of these*/
-
-#define CFG_USB_DEVICE 0x50000000
-#define CFG_NVRAM_BASE_ADDR 0x80000000
-#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000)
-#define CFG_BOOT_BASE_ADDR 0xf0000000
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in SDRAM)
- *----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */
-#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */
-#define CFG_INIT_RAM_END (8 << 10)
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
-/*define this if you want console on UART1*/
-#undef CONFIG_UART1_CONSOLE
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-/*
- * Define here the location of the environment variables (FLASH or EEPROM).
- * Note: DENX encourages to use redundant environment in FLASH.
- */
-#if 1
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#else
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#endif
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
-#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */
-
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#endif /* CFG_ENV_IS_IN_FLASH */
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------*/
-#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
-#define CFG_KBYTES_SDRAM (128 * 1024) /* 128MB */
-#define CFG_SDRAM_BANKS (2)
-
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-#ifdef CFG_ENV_IS_IN_EEPROM
-#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */
-#define CFG_ENV_OFFSET 0x0
-#endif /* CFG_ENV_IS_IN_EEPROM */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=yellowstone\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/yellowstone/uImage\0" \
- "kernel_addr=fc000000\0" \
- "ramdisk_addr=fc180000\0" \
- "load=tftp 100000 /tftpboot/yellowstone/u-boot.bin\0" \
- "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \
- "cp.b 100000 fff80000 80000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_NET_MULTI 1 /* required for netconsole */
-#define CONFIG_PHY1_ADDR 3
-#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
-#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
-
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-#ifdef CONFIG_440EP
-/* USB */
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-
-/*Comment this out to enable USB 1.1 device*/
-#define USB_2_0_DEVICE
-#endif /*CONFIG_440EP*/
-
-#ifdef DEBUG
-#define CONFIG_PANIC_HANG
-#else
-#define CONFIG_HW_WATCHDOG /* watchdog */
-#endif
-
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_ELF | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CONFIG_LYNXKDI 1 /* support kdi files */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI /* include pci support */
-#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
-
-/* Board-specific PCI */
-#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
-#define CFG_PCI_TARGET_INIT
-#define CFG_PCI_MASTER_INIT
-
-#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- *----------------------------------------------------------------------*/
-#define CFG_FLASH CFG_FLASH_BASE
-#define CFG_CPLD 0x80000000
-
-/* Memory Bank 0 (NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x03017300
-#define CFG_EBC_PB0CR (CFG_FLASH | 0xda000)
-
-/* Memory Bank 2 (CPLD) initialization */
-#define CFG_EBC_PB2AP 0x04814500
-#define CFG_EBC_PB2CR (CFG_CPLD | 0x18000)
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff