]> git.dujemihanovic.xyz Git - u-boot.git/commitdiff
powerpc/8xxx: Add support for interactive DDR programming interface
authorYork Sun <yorksun@freescale.com>
Fri, 16 Sep 2011 20:21:35 +0000 (13:21 -0700)
committerKumar Gala <galak@kernel.crashing.org>
Sun, 9 Oct 2011 22:57:53 +0000 (17:57 -0500)
Interactive DDR debugging provides a user interface to view and modify SPD,
DIMM parameters, board options and DDR controller registers before DDR is
initialized. With this feature, developers can fine-tune DDR for board
bringup and other debugging without frequently having to reprogram the flash.

To enable this feature, define CONFIG_FSL_DDR_INTERACTIVE in board header
file and set an environment variable to activate it. Syntax:

setenv ddr_interactive on

After reset, U-boot prompts before initializing DDR controllers
FSL DDR>

The available commands are
print      print SPD and intermediate computed data
reset      reboot machine
recompute  reload SPD and options to default and recompute regs
edit       modify spd, parameter, or option
compute    recompute registers from current next_step to end
next_step  shows current next_step
help       this message
go         program the memory controller and continue with u-boot

The first command should be "compute", which reads data from DIMM SPDs and
board options, performs the calculation then stops before setting DDR
controller. A user can use "print" and "edit" commands to view and modify
anything. "Go" picks up from current step with any modification and
compltes the calculation then enables the DDR controller to continue u-boot.
"Recompute" does it over from fresh reading.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
README
arch/powerpc/cpu/mpc8xxx/ddr/Makefile
arch/powerpc/cpu/mpc8xxx/ddr/ddr.h
arch/powerpc/cpu/mpc8xxx/ddr/interactive.c [new file with mode: 0644]
arch/powerpc/cpu/mpc8xxx/ddr/main.c
doc/README.fsl-ddr
include/configs/p1_p2_rdb_pc.h

diff --git a/README b/README
index 3a8938f4e3cb6d52a9ad16a707f35f6e43d796ce..36f5a1123c9cfb6220742efa14c89039d557848c 100644 (file)
--- a/README
+++ b/README
@@ -3099,6 +3099,9 @@ Low Level (hardware related) configuration options:
                parameters are extracted from datasheet and hard-coded into
                header files or board specific files.
 
+- CONFIG_FSL_DDR_INTERACTIVE
+               Enable interactive DDR debugging. See doc/README.fsl-ddr.
+
 - CONFIG_SYS_83XX_DDR_USES_CS0
                Only for 83xx systems. If specified, then DDR should
                be configured using CS0 and CS1 instead of CS2 and CS3.
index d1b4c4b470461b3ebb400b9d7abccb81e5881e9a..29523aa9139b8d55c74cd2df4635994af7a99197 100644 (file)
@@ -1,5 +1,5 @@
 #
-# Copyright 2008 Freescale Semiconductor, Inc.
+# Copyright 2008-2011 Freescale Semiconductor, Inc.
 #
 # This program is free software; you can redistribute it and/or
 # modify it under the terms of the GNU General Public License
@@ -30,6 +30,7 @@ COBJS-$(CONFIG_FSL_DDR2)      += ddr2_dimm_params.o
 COBJS-$(CONFIG_FSL_DDR3)       += ddr3_dimm_params.o
 endif
 
+COBJS-$(CONFIG_FSL_DDR_INTERACTIVE) += interactive.o
 
 SRCS   := $(START:.o=.S) $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
 OBJS   := $(addprefix $(obj),$(SOBJS-y) $(COBJS-y))
index f59aa33b227085d72cd448383009a9fab6996f95..c8b0f916763340a0fead834dbce1a5fb4411401d 100644 (file)
@@ -56,32 +56,46 @@ typedef struct {
 #define STEP_PROGRAM_REGS            (1 << 6)
 #define STEP_ALL                     0xFFF
 
-extern unsigned long long
+unsigned long long
 fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step,
                                       unsigned int size_only);
 
-extern const char * step_to_string(unsigned int step);
+const char *step_to_string(unsigned int step);
 
-extern unsigned int
-compute_fsl_memctl_config_regs(const memctl_options_t *popts,
+unsigned int compute_fsl_memctl_config_regs(const memctl_options_t *popts,
                               fsl_ddr_cfg_regs_t *ddr,
                               const common_timing_params_t *common_dimm,
                               const dimm_params_t *dimm_parameters,
                               unsigned int dbw_capacity_adjust,
                               unsigned int size_only);
-extern unsigned int
-compute_lowest_common_dimm_parameters(const dimm_params_t *dimm_params,
-                                     common_timing_params_t *outpdimm,
-                                     unsigned int number_of_dimms);
-extern unsigned int populate_memctl_options(int all_DIMMs_registered,
+unsigned int compute_lowest_common_dimm_parameters(
+                               const dimm_params_t *dimm_params,
+                               common_timing_params_t *outpdimm,
+                               unsigned int number_of_dimms);
+unsigned int populate_memctl_options(int all_DIMMs_registered,
                                memctl_options_t *popts,
                                dimm_params_t *pdimm,
                                unsigned int ctrl_num);
-extern void check_interleaving_options(fsl_ddr_info_t *pinfo);
+void check_interleaving_options(fsl_ddr_info_t *pinfo);
 
-extern unsigned int mclk_to_picos(unsigned int mclk);
-extern unsigned int get_memory_clk_period_ps(void);
-extern unsigned int picos_to_mclk(unsigned int picos);
+unsigned int mclk_to_picos(unsigned int mclk);
+unsigned int get_memory_clk_period_ps(void);
+unsigned int picos_to_mclk(unsigned int picos);
+void fsl_ddr_set_lawbar(
+               const common_timing_params_t *memctl_common_params,
+               unsigned int memctl_interleaved,
+               unsigned int ctrl_num);
+
+unsigned long long fsl_ddr_interactive(fsl_ddr_info_t *pinfo);
+void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd,
+                          unsigned int ctrl_num);
+
+int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]);
+unsigned int check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr);
+
+/* processor specific function */
+void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
+                                  unsigned int ctrl_num);
 
 /* board specific function */
 int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/interactive.c b/arch/powerpc/cpu/mpc8xxx/ddr/interactive.c
new file mode 100644 (file)
index 0000000..d7d66ef
--- /dev/null
@@ -0,0 +1,1691 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 or any later versionas published by the Free Software Foundation.
+ */
+
+/*
+ * Generic driver for Freescale DDR/DDR2/DDR3 memory controller.
+ * Based on code from spd_sdram.c
+ * Author: James Yang [at freescale.com]
+ *         York Sun [at freescale.com]
+ */
+
+#include <common.h>
+#include <linux/ctype.h>
+#include <asm/types.h>
+
+#include <asm/fsl_ddr_sdram.h>
+#include "ddr.h"
+
+/* Option parameter Structures */
+struct options_string {
+       const char *option_name;
+       size_t offset;
+       unsigned int size;
+       const char printhex;
+};
+
+static unsigned int picos_to_mhz(unsigned int picos)
+{
+       return 1000000 / picos;
+}
+
+static void print_option_table(const struct options_string *table,
+                        int table_size,
+                        const void *base)
+{
+       unsigned int i;
+       unsigned int *ptr;
+       unsigned long long *ptr_l;
+
+       for (i = 0; i < table_size; i++) {
+               switch (table[i].size) {
+               case 4:
+                       ptr = (unsigned int *) (base + table[i].offset);
+                       if (table[i].printhex) {
+                               printf("%s = 0x%08X\n",
+                                       table[i].option_name, *ptr);
+                       } else {
+                               printf("%s = %u\n",
+                                       table[i].option_name, *ptr);
+                       }
+                       break;
+               case 8:
+                       ptr_l = (unsigned long long *) (base + table[i].offset);
+                       printf("%s = %llu\n",
+                               table[i].option_name, *ptr_l);
+                       break;
+               default:
+                       printf("Unrecognized size!\n");
+                       break;
+               }
+       }
+}
+
+static int handle_option_table(const struct options_string *table,
+                        int table_size,
+                        void *base,
+                        const char *opt,
+                        const char *val)
+{
+       unsigned int i;
+       unsigned int value, *ptr;
+       unsigned long long value_l, *ptr_l;
+
+       for (i = 0; i < table_size; i++) {
+               if (strcmp(table[i].option_name, opt) != 0)
+                       continue;
+               switch (table[i].size) {
+               case 4:
+                       value = simple_strtoul(val, NULL, 0);
+                       ptr = base + table[i].offset;
+                       *ptr = value;
+                       break;
+               case 8:
+                       value_l = simple_strtoull(val, NULL, 0);
+                       ptr_l = base + table[i].offset;
+                       *ptr_l = value_l;
+                       break;
+               default:
+                       printf("Unrecognized size!\n");
+                       break;
+               }
+               return 1;
+       }
+
+       return 0;
+}
+
+static void fsl_ddr_generic_edit(void *pdata,
+                          void *pend,
+                          unsigned int element_size,
+                          unsigned int element_num,
+                          unsigned int value)
+{
+       char *pcdata = (char *)pdata;           /* BIG ENDIAN ONLY */
+
+       pcdata += element_num * element_size;
+       if ((pcdata + element_size) > (char *) pend) {
+               printf("trying to write past end of data\n");
+               return;
+       }
+
+       switch (element_size) {
+       case 1:
+               __raw_writeb(value, pcdata);
+               break;
+       case 2:
+               __raw_writew(value, pcdata);
+               break;
+       case 4:
+               __raw_writel(value, pcdata);
+               break;
+       default:
+               printf("unexpected element size %u\n", element_size);
+               break;
+       }
+}
+
+static void fsl_ddr_spd_edit(fsl_ddr_info_t *pinfo,
+                      unsigned int ctrl_num,
+                      unsigned int dimm_num,
+                      unsigned int element_num,
+                      unsigned int value)
+{
+       generic_spd_eeprom_t *pspd;
+
+       pspd = &(pinfo->spd_installed_dimms[ctrl_num][dimm_num]);
+       fsl_ddr_generic_edit(pspd, pspd + 1, 1, element_num, value);
+}
+
+#define COMMON_TIMING(x) {#x, offsetof(common_timing_params_t, x), \
+       sizeof((common_timing_params_t *)0)->x, 0}
+
+static void lowest_common_dimm_parameters_edit(fsl_ddr_info_t *pinfo,
+                                       unsigned int ctrl_num,
+                                       const char *optname_str,
+                                       const char *value_str)
+{
+       common_timing_params_t *p = &pinfo->common_timing_params[ctrl_num];
+
+       static const struct options_string options[] = {
+               COMMON_TIMING(tCKmin_X_ps),
+               COMMON_TIMING(tCKmax_ps),
+               COMMON_TIMING(tCKmax_max_ps),
+               COMMON_TIMING(tRCD_ps),
+               COMMON_TIMING(tRP_ps),
+               COMMON_TIMING(tRAS_ps),
+               COMMON_TIMING(tWR_ps),
+               COMMON_TIMING(tWTR_ps),
+               COMMON_TIMING(tRFC_ps),
+               COMMON_TIMING(tRRD_ps),
+               COMMON_TIMING(tRC_ps),
+               COMMON_TIMING(refresh_rate_ps),
+               COMMON_TIMING(tIS_ps),
+               COMMON_TIMING(tIH_ps),
+               COMMON_TIMING(tDS_ps),
+               COMMON_TIMING(tDH_ps),
+               COMMON_TIMING(tRTP_ps),
+               COMMON_TIMING(tDQSQ_max_ps),
+               COMMON_TIMING(tQHS_ps),
+               COMMON_TIMING(ndimms_present),
+               COMMON_TIMING(lowest_common_SPD_caslat),
+               COMMON_TIMING(highest_common_derated_caslat),
+               COMMON_TIMING(additive_latency),
+               COMMON_TIMING(all_DIMMs_burst_lengths_bitmask),
+               COMMON_TIMING(all_DIMMs_registered),
+               COMMON_TIMING(all_DIMMs_unbuffered),
+               COMMON_TIMING(all_DIMMs_ECC_capable),
+               COMMON_TIMING(total_mem),
+               COMMON_TIMING(base_address),
+       };
+       static const unsigned int n_opts = ARRAY_SIZE(options);
+
+       if (handle_option_table(options, n_opts, p, optname_str, value_str))
+               return;
+
+       printf("Error: couldn't find option string %s\n", optname_str);
+}
+
+#define DIMM_PARM(x) {#x, offsetof(dimm_params_t, x), \
+       sizeof((dimm_params_t *)0)->x, 0}
+
+static void fsl_ddr_dimm_parameters_edit(fsl_ddr_info_t *pinfo,
+                                  unsigned int ctrl_num,
+                                  unsigned int dimm_num,
+                                  const char *optname_str,
+                                  const char *value_str)
+{
+       dimm_params_t *p = &(pinfo->dimm_params[ctrl_num][dimm_num]);
+
+       static const struct options_string options[] = {
+               DIMM_PARM(n_ranks),
+               DIMM_PARM(data_width),
+               DIMM_PARM(primary_sdram_width),
+               DIMM_PARM(ec_sdram_width),
+               DIMM_PARM(registered_dimm),
+
+               DIMM_PARM(n_row_addr),
+               DIMM_PARM(n_col_addr),
+               DIMM_PARM(edc_config),
+               DIMM_PARM(n_banks_per_sdram_device),
+               DIMM_PARM(burst_lengths_bitmask),
+               DIMM_PARM(row_density),
+
+               DIMM_PARM(tCKmin_X_ps),
+               DIMM_PARM(tCKmin_X_minus_1_ps),
+               DIMM_PARM(tCKmin_X_minus_2_ps),
+               DIMM_PARM(tCKmax_ps),
+
+               DIMM_PARM(caslat_X),
+               DIMM_PARM(caslat_X_minus_1),
+               DIMM_PARM(caslat_X_minus_2),
+
+               DIMM_PARM(caslat_lowest_derated),
+
+               DIMM_PARM(tRCD_ps),
+               DIMM_PARM(tRP_ps),
+               DIMM_PARM(tRAS_ps),
+               DIMM_PARM(tWR_ps),
+               DIMM_PARM(tWTR_ps),
+               DIMM_PARM(tRFC_ps),
+               DIMM_PARM(tRRD_ps),
+               DIMM_PARM(tRC_ps),
+               DIMM_PARM(refresh_rate_ps),
+
+               DIMM_PARM(tIS_ps),
+               DIMM_PARM(tIH_ps),
+               DIMM_PARM(tDS_ps),
+               DIMM_PARM(tDH_ps),
+               DIMM_PARM(tRTP_ps),
+               DIMM_PARM(tDQSQ_max_ps),
+               DIMM_PARM(tQHS_ps),
+
+               DIMM_PARM(rank_density),
+               DIMM_PARM(capacity),
+               DIMM_PARM(base_address),
+       };
+
+       static const unsigned int n_opts = ARRAY_SIZE(options);
+
+       if (handle_option_table(options, n_opts, p, optname_str, value_str))
+               return;
+
+       printf("couldn't find option string %s\n", optname_str);
+}
+
+static void print_dimm_parameters(const dimm_params_t *pdimm)
+{
+       static const struct options_string options[] = {
+               DIMM_PARM(n_ranks),
+               DIMM_PARM(data_width),
+               DIMM_PARM(primary_sdram_width),
+               DIMM_PARM(ec_sdram_width),
+               DIMM_PARM(registered_dimm),
+
+               DIMM_PARM(n_row_addr),
+               DIMM_PARM(n_col_addr),
+               DIMM_PARM(edc_config),
+               DIMM_PARM(n_banks_per_sdram_device),
+
+               DIMM_PARM(tCKmin_X_ps),
+               DIMM_PARM(tCKmin_X_minus_1_ps),
+               DIMM_PARM(tCKmin_X_minus_2_ps),
+               DIMM_PARM(tCKmax_ps),
+
+               DIMM_PARM(caslat_X),
+               DIMM_PARM(tAA_ps),
+               DIMM_PARM(caslat_X_minus_1),
+               DIMM_PARM(caslat_X_minus_2),
+               DIMM_PARM(caslat_lowest_derated),
+
+               DIMM_PARM(tRCD_ps),
+               DIMM_PARM(tRP_ps),
+               DIMM_PARM(tRAS_ps),
+               DIMM_PARM(tWR_ps),
+               DIMM_PARM(tWTR_ps),
+               DIMM_PARM(tRFC_ps),
+               DIMM_PARM(tRRD_ps),
+               DIMM_PARM(tRC_ps),
+               DIMM_PARM(refresh_rate_ps),
+
+               DIMM_PARM(tIS_ps),
+               DIMM_PARM(tIH_ps),
+               DIMM_PARM(tDS_ps),
+               DIMM_PARM(tDH_ps),
+               DIMM_PARM(tRTP_ps),
+               DIMM_PARM(tDQSQ_max_ps),
+               DIMM_PARM(tQHS_ps),
+       };
+       static const unsigned int n_opts = ARRAY_SIZE(options);
+
+       if (pdimm->n_ranks == 0) {
+               printf("DIMM not present\n");
+               return;
+       }
+       printf("DIMM organization parameters:\n");
+       printf("module part name = %s\n", pdimm->mpart);
+       printf("rank_density = %llu bytes (%llu megabytes)\n",
+              pdimm->rank_density, pdimm->rank_density / 0x100000);
+       printf("capacity = %llu bytes (%llu megabytes)\n",
+              pdimm->capacity, pdimm->capacity / 0x100000);
+       printf("burst_lengths_bitmask = %02X\n",
+              pdimm->burst_lengths_bitmask);
+       printf("base_addresss = %llu (%08llX %08llX)\n",
+              pdimm->base_address,
+              (pdimm->base_address >> 32),
+              pdimm->base_address & 0xFFFFFFFF);
+       print_option_table(options, n_opts, pdimm);
+}
+
+static void print_lowest_common_dimm_parameters(
+               const common_timing_params_t *plcd_dimm_params)
+{
+       static const struct options_string options[] = {
+               COMMON_TIMING(tCKmax_max_ps),
+               COMMON_TIMING(tRCD_ps),
+               COMMON_TIMING(tRP_ps),
+               COMMON_TIMING(tRAS_ps),
+               COMMON_TIMING(tWR_ps),
+               COMMON_TIMING(tWTR_ps),
+               COMMON_TIMING(tRFC_ps),
+               COMMON_TIMING(tRRD_ps),
+               COMMON_TIMING(tRC_ps),
+               COMMON_TIMING(refresh_rate_ps),
+               COMMON_TIMING(tIS_ps),
+               COMMON_TIMING(tDS_ps),
+               COMMON_TIMING(tDH_ps),
+               COMMON_TIMING(tRTP_ps),
+               COMMON_TIMING(tDQSQ_max_ps),
+               COMMON_TIMING(tQHS_ps),
+               COMMON_TIMING(lowest_common_SPD_caslat),
+               COMMON_TIMING(highest_common_derated_caslat),
+               COMMON_TIMING(additive_latency),
+               COMMON_TIMING(ndimms_present),
+               COMMON_TIMING(all_DIMMs_registered),
+               COMMON_TIMING(all_DIMMs_unbuffered),
+               COMMON_TIMING(all_DIMMs_ECC_capable),
+       };
+       static const unsigned int n_opts = ARRAY_SIZE(options);
+
+       /* Clock frequencies */
+       printf("tCKmin_X_ps = %u (%u MHz)\n",
+              plcd_dimm_params->tCKmin_X_ps,
+              picos_to_mhz(plcd_dimm_params->tCKmin_X_ps));
+       printf("tCKmax_ps = %u (%u MHz)\n",
+              plcd_dimm_params->tCKmax_ps,
+              picos_to_mhz(plcd_dimm_params->tCKmax_ps));
+       printf("all_DIMMs_burst_lengths_bitmask = %02X\n",
+              plcd_dimm_params->all_DIMMs_burst_lengths_bitmask);
+
+       print_option_table(options, n_opts, plcd_dimm_params);
+
+       printf("total_mem = %llu (%llu megabytes)\n",
+              plcd_dimm_params->total_mem,
+              plcd_dimm_params->total_mem / 0x100000);
+       printf("base_address = %llu (%llu megabytes)\n",
+              plcd_dimm_params->base_address,
+              plcd_dimm_params->base_address / 0x100000);
+}
+
+#define CTRL_OPTIONS(x) {#x, offsetof(memctl_options_t, x), \
+       sizeof((memctl_options_t *)0)->x, 0}
+#define CTRL_OPTIONS_CS(x, y) {"cs" #x "_" #y, \
+       offsetof(memctl_options_t, cs_local_opts[x].y), \
+       sizeof((memctl_options_t *)0)->cs_local_opts[x].y, 0}
+
+static void fsl_ddr_options_edit(fsl_ddr_info_t *pinfo,
+                          unsigned int ctl_num,
+                          const char *optname_str,
+                          const char *value_str)
+{
+       memctl_options_t *p = &(pinfo->memctl_opts[ctl_num]);
+       /*
+        * This array all on the stack and *computed* each time this
+        * function is rung.
+        */
+       static const struct options_string options[] = {
+               CTRL_OPTIONS_CS(0, odt_rd_cfg),
+               CTRL_OPTIONS_CS(0, odt_wr_cfg),
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1)
+               CTRL_OPTIONS_CS(1, odt_rd_cfg),
+               CTRL_OPTIONS_CS(1, odt_wr_cfg),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2)
+               CTRL_OPTIONS_CS(2, odt_rd_cfg),
+               CTRL_OPTIONS_CS(2, odt_wr_cfg),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2)
+               CTRL_OPTIONS_CS(3, odt_rd_cfg),
+               CTRL_OPTIONS_CS(3, odt_wr_cfg),
+#endif
+#if defined(CONFIG_FSL_DDR3)
+               CTRL_OPTIONS_CS(0, odt_rtt_norm),
+               CTRL_OPTIONS_CS(0, odt_rtt_wr),
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1)
+               CTRL_OPTIONS_CS(1, odt_rtt_norm),
+               CTRL_OPTIONS_CS(1, odt_rtt_wr),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2)
+               CTRL_OPTIONS_CS(2, odt_rtt_norm),
+               CTRL_OPTIONS_CS(2, odt_rtt_wr),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2)
+               CTRL_OPTIONS_CS(3, odt_rtt_norm),
+               CTRL_OPTIONS_CS(3, odt_rtt_wr),
+#endif
+#endif
+               CTRL_OPTIONS(memctl_interleaving),
+               CTRL_OPTIONS(memctl_interleaving_mode),
+               CTRL_OPTIONS(ba_intlv_ctl),
+               CTRL_OPTIONS(ECC_mode),
+               CTRL_OPTIONS(ECC_init_using_memctl),
+               CTRL_OPTIONS(DQS_config),
+               CTRL_OPTIONS(self_refresh_in_sleep),
+               CTRL_OPTIONS(dynamic_power),
+               CTRL_OPTIONS(data_bus_width),
+               CTRL_OPTIONS(burst_length),
+               CTRL_OPTIONS(cas_latency_override),
+               CTRL_OPTIONS(cas_latency_override_value),
+               CTRL_OPTIONS(use_derated_caslat),
+               CTRL_OPTIONS(additive_latency_override),
+               CTRL_OPTIONS(additive_latency_override_value),
+               CTRL_OPTIONS(clk_adjust),
+               CTRL_OPTIONS(cpo_override),
+               CTRL_OPTIONS(write_data_delay),
+               CTRL_OPTIONS(half_strength_driver_enable),
+
+               /*
+                * These can probably be changed to 2T_EN and 3T_EN
+                * (using a leading numerical character) without problem
+                */
+               CTRL_OPTIONS(twoT_en),
+               CTRL_OPTIONS(threeT_en),
+               CTRL_OPTIONS(ap_en),
+               CTRL_OPTIONS(bstopre),
+               CTRL_OPTIONS(wrlvl_override),
+               CTRL_OPTIONS(wrlvl_sample),
+               CTRL_OPTIONS(wrlvl_start),
+               CTRL_OPTIONS(rcw_override),
+               CTRL_OPTIONS(rcw_1),
+               CTRL_OPTIONS(rcw_2),
+               CTRL_OPTIONS(tCKE_clock_pulse_width_ps),
+               CTRL_OPTIONS(tFAW_window_four_activates_ps),
+               CTRL_OPTIONS(trwt_override),
+               CTRL_OPTIONS(trwt),
+       };
+
+       static const unsigned int n_opts = ARRAY_SIZE(options);
+
+       if (handle_option_table(options, n_opts, p,
+                                       optname_str, value_str))
+               return;
+
+       printf("couldn't find option string %s\n", optname_str);
+}
+
+#define CFG_REGS(x) {#x, offsetof(fsl_ddr_cfg_regs_t, x), \
+       sizeof((fsl_ddr_cfg_regs_t *)0)->x, 1}
+#define CFG_REGS_CS(x, y) {"cs" #x "_" #y, \
+       offsetof(fsl_ddr_cfg_regs_t, cs[x].y), \
+       sizeof((fsl_ddr_cfg_regs_t *)0)->cs[x].y, 1}
+
+static void print_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr)
+{
+       unsigned int i;
+       static const struct options_string options[] = {
+               CFG_REGS_CS(0, bnds),
+               CFG_REGS_CS(0, config),
+               CFG_REGS_CS(0, config_2),
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1)
+               CFG_REGS_CS(1, bnds),
+               CFG_REGS_CS(1, config),
+               CFG_REGS_CS(1, config_2),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2)
+               CFG_REGS_CS(2, bnds),
+               CFG_REGS_CS(2, config),
+               CFG_REGS_CS(2, config_2),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2)
+               CFG_REGS_CS(3, bnds),
+               CFG_REGS_CS(3, config),
+               CFG_REGS_CS(3, config_2),
+#endif
+               CFG_REGS(timing_cfg_3),
+               CFG_REGS(timing_cfg_0),
+               CFG_REGS(timing_cfg_1),
+               CFG_REGS(timing_cfg_2),
+               CFG_REGS(ddr_sdram_cfg),
+               CFG_REGS(ddr_sdram_cfg_2),
+               CFG_REGS(ddr_sdram_mode),
+               CFG_REGS(ddr_sdram_mode_2),
+               CFG_REGS(ddr_sdram_mode_3),
+               CFG_REGS(ddr_sdram_mode_4),
+               CFG_REGS(ddr_sdram_mode_5),
+               CFG_REGS(ddr_sdram_mode_6),
+               CFG_REGS(ddr_sdram_mode_7),
+               CFG_REGS(ddr_sdram_mode_8),
+               CFG_REGS(ddr_sdram_interval),
+               CFG_REGS(ddr_data_init),
+               CFG_REGS(ddr_sdram_clk_cntl),
+               CFG_REGS(ddr_init_addr),
+               CFG_REGS(ddr_init_ext_addr),
+               CFG_REGS(timing_cfg_4),
+               CFG_REGS(timing_cfg_5),
+               CFG_REGS(ddr_zq_cntl),
+               CFG_REGS(ddr_wrlvl_cntl),
+               CFG_REGS(ddr_sr_cntr),
+               CFG_REGS(ddr_sdram_rcw_1),
+               CFG_REGS(ddr_sdram_rcw_2),
+               CFG_REGS(ddr_cdr1),
+               CFG_REGS(ddr_cdr2),
+               CFG_REGS(err_disable),
+               CFG_REGS(err_int_en),
+       };
+       static const unsigned int n_opts = ARRAY_SIZE(options);
+
+       print_option_table(options, n_opts, ddr);
+
+       for (i = 0; i < 32; i++)
+               printf("debug_%02d = 0x%08X\n", i+1, ddr->debug[i]);
+}
+
+static void fsl_ddr_regs_edit(fsl_ddr_info_t *pinfo,
+                       unsigned int ctrl_num,
+                       const char *regname,
+                       const char *value_str)
+{
+       unsigned int i;
+       fsl_ddr_cfg_regs_t *ddr;
+       char buf[20];
+       static const struct options_string options[] = {
+               CFG_REGS_CS(0, bnds),
+               CFG_REGS_CS(0, config),
+               CFG_REGS_CS(0, config_2),
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1)
+               CFG_REGS_CS(1, bnds),
+               CFG_REGS_CS(1, config),
+               CFG_REGS_CS(1, config_2),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2)
+               CFG_REGS_CS(2, bnds),
+               CFG_REGS_CS(2, config),
+               CFG_REGS_CS(2, config_2),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 3)
+               CFG_REGS_CS(3, bnds),
+               CFG_REGS_CS(3, config),
+               CFG_REGS_CS(3, config_2),
+#endif
+               CFG_REGS(timing_cfg_3),
+               CFG_REGS(timing_cfg_0),
+               CFG_REGS(timing_cfg_1),
+               CFG_REGS(timing_cfg_2),
+               CFG_REGS(ddr_sdram_cfg),
+               CFG_REGS(ddr_sdram_cfg_2),
+               CFG_REGS(ddr_sdram_mode),
+               CFG_REGS(ddr_sdram_mode_2),
+               CFG_REGS(ddr_sdram_mode_3),
+               CFG_REGS(ddr_sdram_mode_4),
+               CFG_REGS(ddr_sdram_mode_5),
+               CFG_REGS(ddr_sdram_mode_6),
+               CFG_REGS(ddr_sdram_mode_7),
+               CFG_REGS(ddr_sdram_mode_8),
+               CFG_REGS(ddr_sdram_interval),
+               CFG_REGS(ddr_data_init),
+               CFG_REGS(ddr_sdram_clk_cntl),
+               CFG_REGS(ddr_init_addr),
+               CFG_REGS(ddr_init_ext_addr),
+               CFG_REGS(timing_cfg_4),
+               CFG_REGS(timing_cfg_5),
+               CFG_REGS(ddr_zq_cntl),
+               CFG_REGS(ddr_wrlvl_cntl),
+               CFG_REGS(ddr_sr_cntr),
+               CFG_REGS(ddr_sdram_rcw_1),
+               CFG_REGS(ddr_sdram_rcw_2),
+               CFG_REGS(ddr_cdr1),
+               CFG_REGS(ddr_cdr2),
+               CFG_REGS(err_disable),
+               CFG_REGS(err_int_en),
+               CFG_REGS(ddr_sdram_rcw_2),
+               CFG_REGS(ddr_sdram_rcw_2),
+
+       };
+       static const unsigned int n_opts = ARRAY_SIZE(options);
+
+       debug("fsl_ddr_regs_edit: ctrl_num = %u, "
+               "regname = %s, value = %s\n",
+               ctrl_num, regname, value_str);
+       if (ctrl_num > CONFIG_NUM_DDR_CONTROLLERS)
+               return;
+
+       ddr = &(pinfo->fsl_ddr_config_reg[ctrl_num]);
+
+       if (handle_option_table(options, n_opts, ddr, regname, value_str))
+               return;
+
+       for (i = 0; i < 32; i++) {
+               unsigned int value = simple_strtoul(value_str, NULL, 0);
+               sprintf(buf, "debug_%u", i + 1);
+               if (strcmp(buf, regname) == 0) {
+                       ddr->debug[i] = value;
+                       return;
+               }
+       }
+       printf("Error: couldn't find register string %s\n", regname);
+}
+
+#define CTRL_OPTIONS_HEX(x) {#x, offsetof(memctl_options_t, x), \
+       sizeof((memctl_options_t *)0)->x, 1}
+
+static void print_memctl_options(const memctl_options_t *popts)
+{
+       static const struct options_string options[] = {
+               CTRL_OPTIONS_CS(0, odt_rd_cfg),
+               CTRL_OPTIONS_CS(0, odt_wr_cfg),
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1)
+               CTRL_OPTIONS_CS(1, odt_rd_cfg),
+               CTRL_OPTIONS_CS(1, odt_wr_cfg),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2)
+               CTRL_OPTIONS_CS(2, odt_rd_cfg),
+               CTRL_OPTIONS_CS(2, odt_wr_cfg),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 3)
+               CTRL_OPTIONS_CS(3, odt_rd_cfg),
+               CTRL_OPTIONS_CS(3, odt_wr_cfg),
+#endif
+#if defined(CONFIG_FSL_DDR3)
+               CTRL_OPTIONS_CS(0, odt_rtt_norm),
+               CTRL_OPTIONS_CS(0, odt_rtt_wr),
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1)
+               CTRL_OPTIONS_CS(1, odt_rtt_norm),
+               CTRL_OPTIONS_CS(1, odt_rtt_wr),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 2)
+               CTRL_OPTIONS_CS(2, odt_rtt_norm),
+               CTRL_OPTIONS_CS(2, odt_rtt_wr),
+#endif
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 3)
+               CTRL_OPTIONS_CS(3, odt_rtt_norm),
+               CTRL_OPTIONS_CS(3, odt_rtt_wr),
+#endif
+#endif
+               CTRL_OPTIONS(memctl_interleaving),
+               CTRL_OPTIONS(memctl_interleaving_mode),
+               CTRL_OPTIONS_HEX(ba_intlv_ctl),
+               CTRL_OPTIONS(ECC_mode),
+               CTRL_OPTIONS(ECC_init_using_memctl),
+               CTRL_OPTIONS(DQS_config),
+               CTRL_OPTIONS(self_refresh_in_sleep),
+               CTRL_OPTIONS(dynamic_power),
+               CTRL_OPTIONS(data_bus_width),
+               CTRL_OPTIONS(burst_length),
+               CTRL_OPTIONS(cas_latency_override),
+               CTRL_OPTIONS(cas_latency_override_value),
+               CTRL_OPTIONS(use_derated_caslat),
+               CTRL_OPTIONS(additive_latency_override),
+               CTRL_OPTIONS(additive_latency_override_value),
+               CTRL_OPTIONS(clk_adjust),
+               CTRL_OPTIONS(cpo_override),
+               CTRL_OPTIONS(write_data_delay),
+               CTRL_OPTIONS(half_strength_driver_enable),
+               /*
+                * These can probably be changed to 2T_EN and 3T_EN
+                * (using a leading numerical character) without problem
+                */
+               CTRL_OPTIONS(twoT_en),
+               CTRL_OPTIONS(threeT_en),
+               CTRL_OPTIONS(registered_dimm_en),
+               CTRL_OPTIONS(ap_en),
+               CTRL_OPTIONS(bstopre),
+               CTRL_OPTIONS(wrlvl_override),
+               CTRL_OPTIONS(wrlvl_sample),
+               CTRL_OPTIONS(wrlvl_start),
+               CTRL_OPTIONS(rcw_override),
+               CTRL_OPTIONS(rcw_1),
+               CTRL_OPTIONS(rcw_2),
+               CTRL_OPTIONS(tCKE_clock_pulse_width_ps),
+               CTRL_OPTIONS(tFAW_window_four_activates_ps),
+               CTRL_OPTIONS(trwt_override),
+               CTRL_OPTIONS(trwt),
+       };
+       static const unsigned int n_opts = ARRAY_SIZE(options);
+
+       print_option_table(options, n_opts, popts);
+}
+
+#ifdef CONFIG_FSL_DDR1
+void ddr1_spd_dump(const ddr1_spd_eeprom_t *spd)
+{
+       unsigned int i;
+
+       printf("%-3d    : %02x %s\n", 0, spd->info_size,
+              " spd->info_size,   *  0 # bytes written into serial memory *");
+       printf("%-3d    : %02x %s\n", 1, spd->chip_size,
+              " spd->chip_size,   *  1 Total # bytes of SPD memory device *");
+       printf("%-3d    : %02x %s\n", 2, spd->mem_type,
+              " spd->mem_type,    *  2 Fundamental memory type *");
+       printf("%-3d    : %02x %s\n", 3, spd->nrow_addr,
+              " spd->nrow_addr,   *  3 # of Row Addresses on this assembly *");
+       printf("%-3d    : %02x %s\n", 4, spd->ncol_addr,
+              " spd->ncol_addr,   *  4 # of Column Addrs on this assembly *");
+       printf("%-3d    : %02x %s\n", 5, spd->nrows,
+              " spd->nrows        *  5 # of DIMM Banks *");
+       printf("%-3d    : %02x %s\n", 6, spd->dataw_lsb,
+              " spd->dataw_lsb,   *  6 Data Width lsb of this assembly *");
+       printf("%-3d    : %02x %s\n", 7, spd->dataw_msb,
+              " spd->dataw_msb,   *  7 Data Width msb of this assembly *");
+       printf("%-3d    : %02x %s\n", 8, spd->voltage,
+              " spd->voltage,     *  8 Voltage intf std of this assembly *");
+       printf("%-3d    : %02x %s\n", 9, spd->clk_cycle,
+              " spd->clk_cycle,   *  9 SDRAM Cycle time at CL=X *");
+       printf("%-3d    : %02x %s\n", 10, spd->clk_access,
+              " spd->clk_access,  * 10 SDRAM Access from Clock at CL=X *");
+       printf("%-3d    : %02x %s\n", 11, spd->config,
+              " spd->config,      * 11 DIMM Configuration type *");
+       printf("%-3d    : %02x %s\n", 12, spd->refresh,
+              " spd->refresh,     * 12 Refresh Rate/Type *");
+       printf("%-3d    : %02x %s\n", 13, spd->primw,
+              " spd->primw,       * 13 Primary SDRAM Width *");
+       printf("%-3d    : %02x %s\n", 14, spd->ecw,
+              " spd->ecw,         * 14 Error Checking SDRAM width *");
+       printf("%-3d    : %02x %s\n", 15, spd->min_delay,
+              " spd->min_delay,   * 15 Back to Back Random Access *");
+       printf("%-3d    : %02x %s\n", 16, spd->burstl,
+              " spd->burstl,      * 16 Burst Lengths Supported *");
+       printf("%-3d    : %02x %s\n", 17, spd->nbanks,
+              " spd->nbanks,      * 17 # of Banks on Each SDRAM Device *");
+       printf("%-3d    : %02x %s\n", 18, spd->cas_lat,
+              " spd->cas_lat,     * 18 CAS# Latencies Supported *");
+       printf("%-3d    : %02x %s\n", 19, spd->cs_lat,
+              " spd->cs_lat,      * 19 Chip Select Latency *");
+       printf("%-3d    : %02x %s\n", 20, spd->write_lat,
+              " spd->write_lat,   * 20 Write Latency/Recovery *");
+       printf("%-3d    : %02x %s\n", 21, spd->mod_attr,
+              " spd->mod_attr,    * 21 SDRAM Module Attributes *");
+       printf("%-3d    : %02x %s\n", 22, spd->dev_attr,
+              " spd->dev_attr,    * 22 SDRAM Device Attributes *");
+       printf("%-3d    : %02x %s\n", 23, spd->clk_cycle2,
+              " spd->clk_cycle2,  * 23 Min SDRAM Cycle time at CL=X-1 *");
+       printf("%-3d    : %02x %s\n", 24, spd->clk_access2,
+              " spd->clk_access2, * 24 SDRAM Access from Clock at CL=X-1 *");
+       printf("%-3d    : %02x %s\n", 25, spd->clk_cycle3,
+              " spd->clk_cycle3,  * 25 Min SDRAM Cycle time at CL=X-2 *");
+       printf("%-3d    : %02x %s\n", 26, spd->clk_access3,
+              " spd->clk_access3, * 26 Max Access from Clock at CL=X-2 *");
+       printf("%-3d    : %02x %s\n", 27, spd->trp,
+              " spd->trp,         * 27 Min Row Precharge Time (tRP)*");
+       printf("%-3d    : %02x %s\n", 28, spd->trrd,
+              " spd->trrd,        * 28 Min Row Active to Row Active (tRRD) *");
+       printf("%-3d    : %02x %s\n", 29, spd->trcd,
+              " spd->trcd,        * 29 Min RAS to CAS Delay (tRCD) *");
+       printf("%-3d    : %02x %s\n", 30, spd->tras,
+              " spd->tras,        * 30 Minimum RAS Pulse Width (tRAS) *");
+       printf("%-3d    : %02x %s\n", 31, spd->bank_dens,
+              " spd->bank_dens,   * 31 Density of each bank on module *");
+       printf("%-3d    : %02x %s\n", 32, spd->ca_setup,
+              " spd->ca_setup,    * 32 Cmd + Addr signal input setup time *");
+       printf("%-3d    : %02x %s\n", 33, spd->ca_hold,
+              " spd->ca_hold,     * 33 Cmd and Addr signal input hold time *");
+       printf("%-3d    : %02x %s\n", 34, spd->data_setup,
+              " spd->data_setup,  * 34 Data signal input setup time *");
+       printf("%-3d    : %02x %s\n", 35, spd->data_hold,
+              " spd->data_hold,   * 35 Data signal input hold time *");
+       printf("%-3d    : %02x %s\n", 36, spd->res_36_40[0],
+              " spd->res_36_40[0], * 36 Reserved / tWR *");
+       printf("%-3d    : %02x %s\n", 37, spd->res_36_40[1],
+              " spd->res_36_40[1], * 37 Reserved / tWTR *");
+       printf("%-3d    : %02x %s\n", 38, spd->res_36_40[2],
+              " spd->res_36_40[2], * 38 Reserved / tRTP *");
+       printf("%-3d    : %02x %s\n", 39, spd->res_36_40[3],
+              " spd->res_36_40[3], * 39 Reserved / mem_probe *");
+       printf("%-3d    : %02x %s\n", 40, spd->res_36_40[4],
+              " spd->res_36_40[4], * 40 Reserved / trc,trfc extensions *");
+       printf("%-3d    : %02x %s\n", 41, spd->trc,
+              " spd->trc,         * 41 Min Active to Auto refresh time tRC *");
+       printf("%-3d    : %02x %s\n", 42, spd->trfc,
+              " spd->trfc,        * 42 Min Auto to Active period tRFC *");
+       printf("%-3d    : %02x %s\n", 43, spd->tckmax,
+              " spd->tckmax,      * 43 Max device cycle time tCKmax *");
+       printf("%-3d    : %02x %s\n", 44, spd->tdqsq,
+              " spd->tdqsq,       * 44 Max DQS to DQ skew *");
+       printf("%-3d    : %02x %s\n", 45, spd->tqhs,
+              " spd->tqhs,        * 45 Max Read DataHold skew tQHS *");
+       printf("%-3d    : %02x %s\n", 46, spd->res_46,
+              " spd->res_46,  * 46 Reserved/ PLL Relock time *");
+       printf("%-3d    : %02x %s\n", 47, spd->dimm_height,
+              " spd->dimm_height  * 47 SDRAM DIMM Height *");
+
+       printf("%-3d-%3d: ",  48, 61);
+
+       for (i = 0; i < 14; i++)
+               printf("%02x", spd->res_48_61[i]);
+
+       printf(" * 48-61 IDD in SPD and Reserved space *\n");
+
+       printf("%-3d    : %02x %s\n", 62, spd->spd_rev,
+              " spd->spd_rev,     * 62 SPD Data Revision Code *");
+       printf("%-3d    : %02x %s\n", 63, spd->cksum,
+              " spd->cksum,       * 63 Checksum for bytes 0-62 *");
+       printf("%-3d-%3d: ",  64, 71);
+
+       for (i = 0; i < 8; i++)
+               printf("%02x", spd->mid[i]);
+
+       printf("* 64 Mfr's JEDEC ID code per JEP-108E *\n");
+       printf("%-3d    : %02x %s\n", 72, spd->mloc,
+              " spd->mloc,        * 72 Manufacturing Location *");
+
+       printf("%-3d-%3d: >>",  73, 90);
+
+       for (i = 0; i < 18; i++)
+               printf("%c", spd->mpart[i]);
+
+       printf("<<* 73 Manufacturer's Part Number *\n");
+
+       printf("%-3d-%3d: %02x %02x %s\n", 91, 92, spd->rev[0], spd->rev[1],
+              "* 91 Revision Code *");
+       printf("%-3d-%3d: %02x %02x %s\n", 93, 94, spd->mdate[0], spd->mdate[1],
+              "* 93 Manufacturing Date *");
+       printf("%-3d-%3d: ", 95, 98);
+
+       for (i = 0; i < 4; i++)
+               printf("%02x", spd->sernum[i]);
+
+       printf("* 95 Assembly Serial Number *\n");
+
+       printf("%-3d-%3d: ", 99, 127);
+
+       for (i = 0; i < 27; i++)
+               printf("%02x", spd->mspec[i]);
+
+       printf("* 99 Manufacturer Specific Data *\n");
+}
+#endif
+
+#ifdef CONFIG_FSL_DDR2
+void ddr2_spd_dump(const ddr2_spd_eeprom_t *spd)
+{
+       unsigned int i;
+
+       printf("%-3d    : %02x %s\n", 0, spd->info_size,
+              " spd->info_size,   *  0 # bytes written into serial memory *");
+       printf("%-3d    : %02x %s\n", 1, spd->chip_size,
+              " spd->chip_size,   *  1 Total # bytes of SPD memory device *");
+       printf("%-3d    : %02x %s\n", 2, spd->mem_type,
+              " spd->mem_type,    *  2 Fundamental memory type *");
+       printf("%-3d    : %02x %s\n", 3, spd->nrow_addr,
+              " spd->nrow_addr,   *  3 # of Row Addresses on this assembly *");
+       printf("%-3d    : %02x %s\n", 4, spd->ncol_addr,
+              " spd->ncol_addr,   *  4 # of Column Addrs on this assembly *");
+       printf("%-3d    : %02x %s\n", 5, spd->mod_ranks,
+              " spd->mod_ranks    *  5 # of Module Rows on this assembly *");
+       printf("%-3d    : %02x %s\n", 6, spd->dataw,
+              " spd->dataw,       *  6 Data Width of this assembly *");
+       printf("%-3d    : %02x %s\n", 7, spd->res_7,
+              " spd->res_7,       *  7 Reserved *");
+       printf("%-3d    : %02x %s\n", 8, spd->voltage,
+              " spd->voltage,     *  8 Voltage intf std of this assembly *");
+       printf("%-3d    : %02x %s\n", 9, spd->clk_cycle,
+              " spd->clk_cycle,   *  9 SDRAM Cycle time at CL=X *");
+       printf("%-3d    : %02x %s\n", 10, spd->clk_access,
+              " spd->clk_access,  * 10 SDRAM Access from Clock at CL=X *");
+       printf("%-3d    : %02x %s\n", 11, spd->config,
+              " spd->config,      * 11 DIMM Configuration type *");
+       printf("%-3d    : %02x %s\n", 12, spd->refresh,
+              " spd->refresh,     * 12 Refresh Rate/Type *");
+       printf("%-3d    : %02x %s\n", 13, spd->primw,
+              " spd->primw,       * 13 Primary SDRAM Width *");
+       printf("%-3d    : %02x %s\n", 14, spd->ecw,
+              " spd->ecw,         * 14 Error Checking SDRAM width *");
+       printf("%-3d    : %02x %s\n", 15, spd->res_15,
+              " spd->res_15,      * 15 Reserved *");
+       printf("%-3d    : %02x %s\n", 16, spd->burstl,
+              " spd->burstl,      * 16 Burst Lengths Supported *");
+       printf("%-3d    : %02x %s\n", 17, spd->nbanks,
+              " spd->nbanks,      * 17 # of Banks on Each SDRAM Device *");
+       printf("%-3d    : %02x %s\n", 18, spd->cas_lat,
+              " spd->cas_lat,     * 18 CAS# Latencies Supported *");
+       printf("%-3d    : %02x %s\n", 19, spd->mech_char,
+              " spd->mech_char,   * 19 Mechanical Characteristics *");
+       printf("%-3d    : %02x %s\n", 20, spd->dimm_type,
+              " spd->dimm_type,   * 20 DIMM type *");
+       printf("%-3d    : %02x %s\n", 21, spd->mod_attr,
+              " spd->mod_attr,    * 21 SDRAM Module Attributes *");
+       printf("%-3d    : %02x %s\n", 22, spd->dev_attr,
+              " spd->dev_attr,    * 22 SDRAM Device Attributes *");
+       printf("%-3d    : %02x %s\n", 23, spd->clk_cycle2,
+              " spd->clk_cycle2,  * 23 Min SDRAM Cycle time at CL=X-1 *");
+       printf("%-3d    : %02x %s\n", 24, spd->clk_access2,
+              " spd->clk_access2, * 24 SDRAM Access from Clock at CL=X-1 *");
+       printf("%-3d    : %02x %s\n", 25, spd->clk_cycle3,
+              " spd->clk_cycle3,  * 25 Min SDRAM Cycle time at CL=X-2 *");
+       printf("%-3d    : %02x %s\n", 26, spd->clk_access3,
+              " spd->clk_access3, * 26 Max Access from Clock at CL=X-2 *");
+       printf("%-3d    : %02x %s\n", 27, spd->trp,
+              " spd->trp,         * 27 Min Row Precharge Time (tRP)*");
+       printf("%-3d    : %02x %s\n", 28, spd->trrd,
+              " spd->trrd,        * 28 Min Row Active to Row Active (tRRD) *");
+       printf("%-3d    : %02x %s\n", 29, spd->trcd,
+              " spd->trcd,        * 29 Min RAS to CAS Delay (tRCD) *");
+       printf("%-3d    : %02x %s\n", 30, spd->tras,
+              " spd->tras,        * 30 Minimum RAS Pulse Width (tRAS) *");
+       printf("%-3d    : %02x %s\n", 31, spd->rank_dens,
+              " spd->rank_dens,   * 31 Density of each rank on module *");
+       printf("%-3d    : %02x %s\n", 32, spd->ca_setup,
+              " spd->ca_setup,    * 32 Cmd + Addr signal input setup time *");
+       printf("%-3d    : %02x %s\n", 33, spd->ca_hold,
+              " spd->ca_hold,     * 33 Cmd and Addr signal input hold time *");
+       printf("%-3d    : %02x %s\n", 34, spd->data_setup,
+              " spd->data_setup,  * 34 Data signal input setup time *");
+       printf("%-3d    : %02x %s\n", 35, spd->data_hold,
+              " spd->data_hold,   * 35 Data signal input hold time *");
+       printf("%-3d    : %02x %s\n", 36, spd->twr,
+              " spd->twr,         * 36 Write Recovery time tWR *");
+       printf("%-3d    : %02x %s\n", 37, spd->twtr,
+              " spd->twtr,        * 37 Int write to read delay tWTR *");
+       printf("%-3d    : %02x %s\n", 38, spd->trtp,
+              " spd->trtp,        * 38 Int read to precharge delay tRTP *");
+       printf("%-3d    : %02x %s\n", 39, spd->mem_probe,
+              " spd->mem_probe,   * 39 Mem analysis probe characteristics *");
+       printf("%-3d    : %02x %s\n", 40, spd->trctrfc_ext,
+              " spd->trctrfc_ext, * 40 Extensions to trc and trfc *");
+       printf("%-3d    : %02x %s\n", 41, spd->trc,
+              " spd->trc,         * 41 Min Active to Auto refresh time tRC *");
+       printf("%-3d    : %02x %s\n", 42, spd->trfc,
+              " spd->trfc,        * 42 Min Auto to Active period tRFC *");
+       printf("%-3d    : %02x %s\n", 43, spd->tckmax,
+              " spd->tckmax,      * 43 Max device cycle time tCKmax *");
+       printf("%-3d    : %02x %s\n", 44, spd->tdqsq,
+              " spd->tdqsq,       * 44 Max DQS to DQ skew *");
+       printf("%-3d    : %02x %s\n", 45, spd->tqhs,
+              " spd->tqhs,        * 45 Max Read DataHold skew tQHS *");
+       printf("%-3d    : %02x %s\n", 46, spd->pll_relock,
+              " spd->pll_relock,  * 46 PLL Relock time *");
+       printf("%-3d    : %02x %s\n", 47, spd->Tcasemax,
+              " spd->Tcasemax,    * 47 Tcasemax *");
+       printf("%-3d    : %02x %s\n", 48, spd->psiTAdram,
+              " spd->psiTAdram,   * 48 Thermal Resistance of DRAM Package "
+              "from Top (Case) to Ambient (Psi T-A DRAM) *");
+       printf("%-3d    : %02x %s\n", 49, spd->dt0_mode,
+              " spd->dt0_mode,    * 49 DRAM Case Temperature Rise from "
+              "Ambient due to Activate-Precharge/Mode Bits "
+              "(DT0/Mode Bits) *)");
+       printf("%-3d    : %02x %s\n", 50, spd->dt2n_dt2q,
+              " spd->dt2n_dt2q,   * 50 DRAM Case Temperature Rise from "
+              "Ambient due to Precharge/Quiet Standby "
+              "(DT2N/DT2Q) *");
+       printf("%-3d    : %02x %s\n", 51, spd->dt2p,
+              " spd->dt2p,        * 51 DRAM Case Temperature Rise from "
+              "Ambient due to Precharge Power-Down (DT2P) *");
+       printf("%-3d    : %02x %s\n", 52, spd->dt3n,
+              " spd->dt3n,        * 52 DRAM Case Temperature Rise from "
+              "Ambient due to Active Standby (DT3N) *");
+       printf("%-3d    : %02x %s\n", 53, spd->dt3pfast,
+              " spd->dt3pfast,    * 53 DRAM Case Temperature Rise from "
+              "Ambient due to Active Power-Down with Fast PDN Exit "
+              "(DT3Pfast) *");
+       printf("%-3d    : %02x %s\n", 54, spd->dt3pslow,
+              " spd->dt3pslow,    * 54 DRAM Case Temperature Rise from "
+              "Ambient due to Active Power-Down with Slow PDN Exit "
+              "(DT3Pslow) *");
+       printf("%-3d    : %02x %s\n", 55, spd->dt4r_dt4r4w,
+              " spd->dt4r_dt4r4w, * 55 DRAM Case Temperature Rise from "
+              "Ambient due to Page Open Burst Read/DT4R4W Mode Bit "
+              "(DT4R/DT4R4W Mode Bit) *");
+       printf("%-3d    : %02x %s\n", 56, spd->dt5b,
+              " spd->dt5b,        * 56 DRAM Case Temperature Rise from "
+              "Ambient due to Burst Refresh (DT5B) *");
+       printf("%-3d    : %02x %s\n", 57, spd->dt7,
+              " spd->dt7,         * 57 DRAM Case Temperature Rise from "
+              "Ambient due to Bank Interleave Reads with "
+              "Auto-Precharge (DT7) *");
+       printf("%-3d    : %02x %s\n", 58, spd->psiTApll,
+              " spd->psiTApll,    * 58 Thermal Resistance of PLL Package form"
+              " Top (Case) to Ambient (Psi T-A PLL) *");
+       printf("%-3d    : %02x %s\n", 59, spd->psiTAreg,
+              " spd->psiTAreg,    * 59 Thermal Reisitance of Register Package"
+              " from Top (Case) to Ambient (Psi T-A Register) *");
+       printf("%-3d    : %02x %s\n", 60, spd->dtpllactive,
+              " spd->dtpllactive, * 60 PLL Case Temperature Rise from "
+              "Ambient due to PLL Active (DT PLL Active) *");
+       printf("%-3d    : %02x %s\n", 61, spd->dtregact,
+              " spd->dtregact,    "
+              "* 61 Register Case Temperature Rise from Ambient due to "
+              "Register Active/Mode Bit (DT Register Active/Mode Bit) *");
+       printf("%-3d    : %02x %s\n", 62, spd->spd_rev,
+              " spd->spd_rev,     * 62 SPD Data Revision Code *");
+       printf("%-3d    : %02x %s\n", 63, spd->cksum,
+              " spd->cksum,       * 63 Checksum for bytes 0-62 *");
+
+       printf("%-3d-%3d: ",  64, 71);
+
+       for (i = 0; i < 8; i++)
+               printf("%02x", spd->mid[i]);
+
+       printf("* 64 Mfr's JEDEC ID code per JEP-108E *\n");
+
+       printf("%-3d    : %02x %s\n", 72, spd->mloc,
+              " spd->mloc,        * 72 Manufacturing Location *");
+
+       printf("%-3d-%3d: >>",  73, 90);
+       for (i = 0; i < 18; i++)
+               printf("%c", spd->mpart[i]);
+
+
+       printf("<<* 73 Manufacturer's Part Number *\n");
+
+       printf("%-3d-%3d: %02x %02x %s\n", 91, 92, spd->rev[0], spd->rev[1],
+              "* 91 Revision Code *");
+       printf("%-3d-%3d: %02x %02x %s\n", 93, 94, spd->mdate[0], spd->mdate[1],
+              "* 93 Manufacturing Date *");
+       printf("%-3d-%3d: ", 95, 98);
+
+       for (i = 0; i < 4; i++)
+               printf("%02x", spd->sernum[i]);
+
+       printf("* 95 Assembly Serial Number *\n");
+
+       printf("%-3d-%3d: ", 99, 127);
+       for (i = 0; i < 27; i++)
+               printf("%02x", spd->mspec[i]);
+
+
+       printf("* 99 Manufacturer Specific Data *\n");
+}
+#endif
+
+#ifdef CONFIG_FSL_DDR3
+void ddr3_spd_dump(const ddr3_spd_eeprom_t *spd)
+{
+       unsigned int i;
+
+       /* General Section: Bytes 0-59 */
+
+#define PRINT_NXS(x, y, z...) printf("%-3d    : %02x " z "\n", x, y);
+#define PRINT_NNXXS(n0, n1, x0, x1, s) \
+       printf("%-3d-%3d: %02x %02x " s "\n", n0, n1, x0, x1);
+
+       PRINT_NXS(0, spd->info_size_crc,
+               "info_size_crc  bytes written into serial memory, "
+               "CRC coverage");
+       PRINT_NXS(1, spd->spd_rev,
+               "spd_rev        SPD Revision");
+       PRINT_NXS(2, spd->mem_type,
+               "mem_type       Key Byte / DRAM Device Type");
+       PRINT_NXS(3, spd->module_type,
+               "module_type    Key Byte / Module Type");
+       PRINT_NXS(4, spd->density_banks,
+               "density_banks  SDRAM Density and Banks");
+       PRINT_NXS(5, spd->addressing,
+               "addressing     SDRAM Addressing");
+       PRINT_NXS(6, spd->module_vdd,
+               "module_vdd     Module Nominal Voltage, VDD");
+       PRINT_NXS(7, spd->organization,
+               "organization   Module Organization");
+       PRINT_NXS(8, spd->bus_width,
+               "bus_width      Module Memory Bus Width");
+       PRINT_NXS(9, spd->ftb_div,
+               "ftb_div        Fine Timebase (FTB) Dividend / Divisor");
+       PRINT_NXS(10, spd->mtb_dividend,
+               "mtb_dividend   Medium Timebase (MTB) Dividend");
+       PRINT_NXS(11, spd->mtb_divisor,
+               "mtb_divisor    Medium Timebase (MTB) Divisor");
+       PRINT_NXS(12, spd->tCK_min,
+               "tCK_min        SDRAM Minimum Cycle Time");
+       PRINT_NXS(13, spd->res_13,
+               "res_13         Reserved");
+       PRINT_NXS(14, spd->caslat_lsb,
+               "caslat_lsb     CAS Latencies Supported, LSB");
+       PRINT_NXS(15, spd->caslat_msb,
+               "caslat_msb     CAS Latencies Supported, MSB");
+       PRINT_NXS(16, spd->tAA_min,
+               "tAA_min        Min CAS Latency Time");
+       PRINT_NXS(17, spd->tWR_min,
+               "tWR_min        Min Write REcovery Time");
+       PRINT_NXS(18, spd->tRCD_min,
+               "tRCD_min       Min RAS# to CAS# Delay Time");
+       PRINT_NXS(19, spd->tRRD_min,
+               "tRRD_min       Min Row Active to Row Active Delay Time");
+       PRINT_NXS(20, spd->tRP_min,
+               "tRP_min        Min Row Precharge Delay Time");
+       PRINT_NXS(21, spd->tRAS_tRC_ext,
+               "tRAS_tRC_ext   Upper Nibbles for tRAS and tRC");
+       PRINT_NXS(22, spd->tRAS_min_lsb,
+               "tRAS_min_lsb   Min Active to Precharge Delay Time, LSB");
+       PRINT_NXS(23, spd->tRC_min_lsb,
+               "tRC_min_lsb    Min Active to Active/Refresh Delay Time, LSB");
+       PRINT_NXS(24, spd->tRFC_min_lsb,
+               "tRFC_min_lsb   Min Refresh Recovery Delay Time LSB");
+       PRINT_NXS(25, spd->tRFC_min_msb,
+               "tRFC_min_msb   Min Refresh Recovery Delay Time MSB");
+       PRINT_NXS(26, spd->tWTR_min,
+               "tWTR_min       Min Internal Write to Read Command Delay Time");
+       PRINT_NXS(27, spd->tRTP_min,
+               "tRTP_min "
+               "Min Internal Read to Precharge Command Delay Time");
+       PRINT_NXS(28, spd->tFAW_msb,
+               "tFAW_msb       Upper Nibble for tFAW");
+       PRINT_NXS(29, spd->tFAW_min,
+               "tFAW_min       Min Four Activate Window Delay Time");
+       PRINT_NXS(30, spd->opt_features,
+               "opt_features   SDRAM Optional Features");
+       PRINT_NXS(31, spd->therm_ref_opt,
+               "therm_ref_opt  SDRAM Thermal and Refresh Opts");
+       PRINT_NXS(32, spd->therm_sensor,
+               "therm_sensor  SDRAM Thermal Sensor");
+       PRINT_NXS(33, spd->device_type,
+               "device_type  SDRAM Device Type");
+
+       printf("%-3d-%3d: ",  34, 59);  /* Reserved, General Section */
+
+       for (i = 34; i <= 59; i++)
+               printf("%02x ", spd->res_34_59[i - 34]);
+
+       puts("\n");
+
+       switch (spd->module_type) {
+       case 0x02:  /* UDIMM */
+       case 0x03:  /* SO-DIMM */
+       case 0x04:  /* Micro-DIMM */
+       case 0x06:  /* Mini-UDIMM */
+               PRINT_NXS(60, spd->mod_section.unbuffered.mod_height,
+                       "mod_height    (Unbuffered) Module Nominal Height");
+               PRINT_NXS(61, spd->mod_section.unbuffered.mod_thickness,
+                       "mod_thickness (Unbuffered) Module Maximum Thickness");
+               PRINT_NXS(62, spd->mod_section.unbuffered.ref_raw_card,
+                       "ref_raw_card  (Unbuffered) Reference Raw Card Used");
+               PRINT_NXS(63, spd->mod_section.unbuffered.addr_mapping,
+                       "addr_mapping  (Unbuffered) Address mapping from "
+                       "Edge Connector to DRAM");
+               break;
+       case 0x01:  /* RDIMM */
+       case 0x05:  /* Mini-RDIMM */
+               PRINT_NXS(60, spd->mod_section.registered.mod_height,
+                       "mod_height    (Registered) Module Nominal Height");
+               PRINT_NXS(61, spd->mod_section.registered.mod_thickness,
+                       "mod_thickness (Registered) Module Maximum Thickness");
+               PRINT_NXS(62, spd->mod_section.registered.ref_raw_card,
+                       "ref_raw_card  (Registered) Reference Raw Card Used");
+               PRINT_NXS(63, spd->mod_section.registered.modu_attr,
+                       "modu_attr     (Registered) DIMM Module Attributes");
+               PRINT_NXS(64, spd->mod_section.registered.thermal,
+                       "thermal       (Registered) Thermal Heat "
+                       "Spreader Solution");
+               PRINT_NXS(65, spd->mod_section.registered.reg_id_lo,
+                       "reg_id_lo     (Registered) Register Manufacturer ID "
+                       "Code, LSB");
+               PRINT_NXS(66, spd->mod_section.registered.reg_id_hi,
+                       "reg_id_hi     (Registered) Register Manufacturer ID "
+                       "Code, MSB");
+               PRINT_NXS(67, spd->mod_section.registered.reg_rev,
+                       "reg_rev       (Registered) Register "
+                       "Revision Number");
+               PRINT_NXS(68, spd->mod_section.registered.reg_type,
+                       "reg_type      (Registered) Register Type");
+               for (i = 69; i <= 76; i++) {
+                       printf("%-3d    : %02x rcw[%d]\n", i,
+                               spd->mod_section.registered.rcw[i-69], i-69);
+               }
+               break;
+       default:
+               /* Module-specific Section, Unsupported Module Type */
+               printf("%-3d-%3d: ", 60, 116);
+
+               for (i = 60; i <= 116; i++)
+                       printf("%02x", spd->mod_section.uc[i - 60]);
+
+               break;
+       }
+
+       /* Unique Module ID: Bytes 117-125 */
+       PRINT_NXS(117, spd->mmid_lsb, "Module MfgID Code LSB - JEP-106");
+       PRINT_NXS(118, spd->mmid_msb, "Module MfgID Code MSB - JEP-106");
+       PRINT_NXS(119, spd->mloc,     "Mfg Location");
+       PRINT_NNXXS(120, 121, spd->mdate[0], spd->mdate[1], "Mfg Date");
+
+       printf("%-3d-%3d: ", 122, 125);
+
+       for (i = 122; i <= 125; i++)
+               printf("%02x ", spd->sernum[i - 122]);
+       printf("   Module Serial Number\n");
+
+       /* CRC: Bytes 126-127 */
+       PRINT_NNXXS(126, 127, spd->crc[0], spd->crc[1], "  SPD CRC");
+
+       /* Other Manufacturer Fields and User Space: Bytes 128-255 */
+       printf("%-3d-%3d: ", 128, 145);
+       for (i = 128; i <= 145; i++)
+               printf("%02x ", spd->mpart[i - 128]);
+       printf("   Mfg's Module Part Number\n");
+
+       PRINT_NNXXS(146, 147, spd->mrev[0], spd->mrev[1],
+               "Module Revision code");
+
+       PRINT_NXS(148, spd->dmid_lsb, "DRAM MfgID Code LSB - JEP-106");
+       PRINT_NXS(149, spd->dmid_msb, "DRAM MfgID Code MSB - JEP-106");
+
+       printf("%-3d-%3d: ", 150, 175);
+       for (i = 150; i <= 175; i++)
+               printf("%02x ", spd->msd[i - 150]);
+       printf("   Mfg's Specific Data\n");
+
+       printf("%-3d-%3d: ", 176, 255);
+       for (i = 176; i <= 255; i++)
+               printf("%02x", spd->cust[i - 176]);
+       printf("   Mfg's Specific Data\n");
+
+}
+#endif
+
+static inline void generic_spd_dump(const generic_spd_eeprom_t *spd)
+{
+#if defined(CONFIG_FSL_DDR1)
+       ddr1_spd_dump(spd);
+#elif defined(CONFIG_FSL_DDR2)
+       ddr2_spd_dump(spd);
+#elif defined(CONFIG_FSL_DDR3)
+       ddr3_spd_dump(spd);
+#endif
+}
+
+static void fsl_ddr_printinfo(const fsl_ddr_info_t *pinfo,
+                       unsigned int ctrl_mask,
+                       unsigned int dimm_mask,
+                       unsigned int do_mask)
+{
+       unsigned int i, j, retval;
+
+       /* STEP 1:  DIMM SPD data */
+       if (do_mask & STEP_GET_SPD) {
+               for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+                       if (!(ctrl_mask & (1 << i)))
+                               continue;
+
+                       for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) {
+                               if (!(dimm_mask & (1 << j)))
+                                       continue;
+
+                               printf("SPD info:  Controller=%u "
+                                               "DIMM=%u\n", i, j);
+                               generic_spd_dump(
+                                       &(pinfo->spd_installed_dimms[i][j]));
+                               printf("\n");
+                       }
+                       printf("\n");
+               }
+               printf("\n");
+       }
+
+       /* STEP 2:  DIMM Parameters */
+       if (do_mask & STEP_COMPUTE_DIMM_PARMS) {
+               for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+                       if (!(ctrl_mask & (1 << i)))
+                               continue;
+                       for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) {
+                               if (!(dimm_mask & (1 << j)))
+                                       continue;
+                               printf("DIMM parameters:  Controller=%u "
+                                               "DIMM=%u\n", i, j);
+                               print_dimm_parameters(
+                                       &(pinfo->dimm_params[i][j]));
+                               printf("\n");
+                       }
+                       printf("\n");
+               }
+               printf("\n");
+       }
+
+       /* STEP 3:  Common Parameters */
+       if (do_mask & STEP_COMPUTE_COMMON_PARMS) {
+               for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+                       if (!(ctrl_mask & (1 << i)))
+                               continue;
+                       printf("\"lowest common\" DIMM parameters:  "
+                                       "Controller=%u\n", i);
+                       print_lowest_common_dimm_parameters(
+                               &pinfo->common_timing_params[i]);
+                       printf("\n");
+               }
+               printf("\n");
+       }
+
+       /* STEP 4:  User Configuration Options */
+       if (do_mask & STEP_GATHER_OPTS) {
+               for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+                       if (!(ctrl_mask & (1 << i)))
+                               continue;
+                       printf("User Config Options: Controller=%u\n", i);
+                       print_memctl_options(&pinfo->memctl_opts[i]);
+                       printf("\n");
+               }
+               printf("\n");
+       }
+
+       /* STEP 5:  Address assignment */
+       if (do_mask & STEP_ASSIGN_ADDRESSES) {
+               for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+                       if (!(ctrl_mask & (1 << i)))
+                               continue;
+                       for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) {
+                               printf("Address Assignment: Controller=%u "
+                                               "DIMM=%u\n", i, j);
+                               printf("Don't have this functionality yet\n");
+                       }
+                       printf("\n");
+               }
+               printf("\n");
+       }
+
+       /* STEP 6:  computed controller register values */
+       if (do_mask & STEP_COMPUTE_REGS) {
+               for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+                       if (!(ctrl_mask & (1 << i)))
+                               continue;
+                       printf("Computed Register Values: Controller=%u\n", i);
+                       print_fsl_memctl_config_regs(
+                               &pinfo->fsl_ddr_config_reg[i]);
+                       retval = check_fsl_memctl_config_regs(
+                               &pinfo->fsl_ddr_config_reg[i]);
+                       if (retval) {
+                               printf("check_fsl_memctl_config_regs "
+                                       "result = %u\n", retval);
+                       }
+                       printf("\n");
+               }
+               printf("\n");
+       }
+}
+
+struct data_strings {
+       const char *data_name;
+       unsigned int step_mask;
+       unsigned int dimm_number_required;
+};
+
+#define DATA_OPTIONS(name, step, dimm) {#name, step, dimm}
+
+unsigned long long fsl_ddr_interactive(fsl_ddr_info_t *pinfo)
+{
+       unsigned long long ddrsize;
+       const char *prompt = "FSL DDR>";
+       unsigned int len;
+       char buffer[CONFIG_SYS_CBSIZE];
+       char *argv[CONFIG_SYS_MAXARGS + 1];     /* NULL terminated */
+       int argc;
+       unsigned int next_step = STEP_GET_SPD;
+       static const struct data_strings options[] = {
+               DATA_OPTIONS(spd, STEP_GET_SPD, 1),
+               DATA_OPTIONS(dimmparms, STEP_COMPUTE_DIMM_PARMS, 1),
+               DATA_OPTIONS(commonparms, STEP_COMPUTE_COMMON_PARMS, 0),
+               DATA_OPTIONS(opts, STEP_GATHER_OPTS, 0),
+               DATA_OPTIONS(addresses, STEP_ASSIGN_ADDRESSES, 0),
+               DATA_OPTIONS(regs, STEP_COMPUTE_REGS, 0),
+       };
+       static const unsigned int n_opts = ARRAY_SIZE(options);
+       const char *usage = {
+               "commands:\n"
+               "print      print SPD and intermediate computed data\n"
+               "reset      reboot machine\n"
+               "recompute  reload SPD and options to default and recompute regs\n"
+               "edit       modify spd, parameter, or option\n"
+               "compute    recompute registers from current next_step to end\n"
+               "next_step  shows current next_step\n"
+               "help       this message\n"
+               "go         program the memory controller and continue with u-boot\n"
+       };
+
+       /*
+        * The strategy for next_step is that it points to the next
+        * step in the computation process that needs to be done.
+        */
+       while (1) {
+               /*
+                * No need to worry for buffer overflow here in
+                * this function;  readline() maxes out at CFG_CBSIZE
+                */
+               len = readline_into_buffer(prompt,  buffer);
+               argc = parse_line(buffer, argv);
+               if (argc == 0)
+                       continue;
+
+
+               if (strcmp(argv[0], "help") == 0) {
+                       puts(usage);
+                       continue;
+               }
+
+               if (strcmp(argv[0], "next_step") == 0) {
+                       printf("next_step = 0x%02X (%s)\n",
+                              next_step,
+                              step_to_string(next_step));
+                       continue;
+               }
+
+               if (strcmp(argv[0], "edit") == 0) {
+                       unsigned int i, j;
+                       unsigned int error = 0;
+                       unsigned int step_mask = 0;
+                       unsigned int ctlr_mask = 0;
+                       unsigned int dimm_mask = 0;
+                       char *p_element = NULL;
+                       char *p_value = NULL;
+                       unsigned int dimm_number_required = 0;
+                       unsigned int ctrl_num;
+                       unsigned int dimm_num;
+                       unsigned int matched = 0;
+
+                       if (argc == 1) {
+                               /* Only the element and value must be last */
+                               printf("edit <c#> <d#> "
+                                       "<spd|dimmparms|commonparms|opts|"
+                                       "addresses|regs> <element> <value>\n");
+                               printf("for spd, specify byte number for "
+                                       "element\n");
+                               continue;
+                       }
+
+                       for (i = 1; i < argc - 2; i++) {
+                               for (j = 0; j < n_opts; j++) {
+                                       if (strcmp(options[j].data_name,
+                                               argv[i]) != 0)
+                                               continue;
+                                       step_mask |= options[j].step_mask;
+                                       dimm_number_required =
+                                               options[j].dimm_number_required;
+                                       matched = 1;
+                                       break;
+                               }
+
+                               if (matched)
+                                       continue;
+
+                               if (argv[i][0] == 'c') {
+                                       char c = argv[i][1];
+                                       if (isdigit(c))
+                                               ctlr_mask |= 1 << (c - '0');
+                                       continue;
+                               }
+
+                               if (argv[i][0] == 'd') {
+                                       char c = argv[i][1];
+                                       if (isdigit(c))
+                                               dimm_mask |= 1 << (c - '0');
+                                       continue;
+                               }
+
+                               printf("unknown arg %s\n", argv[i]);
+                               step_mask = 0;
+                               error = 1;
+                               break;
+                       }
+
+
+                       if (error)
+                               continue;
+
+
+                       /* Check arguments */
+
+                       /* ERROR: If no steps were found */
+                       if (step_mask == 0) {
+                               printf("Error: No valid steps were specified "
+                                               "in argument.\n");
+                               continue;
+                       }
+
+                       /* ERROR: If multiple steps were found */
+                       if (step_mask & (step_mask - 1)) {
+                               printf("Error: Multiple steps specified in "
+                                               "argument.\n");
+                               continue;
+                       }
+
+                       /* ERROR: Controller not specified */
+                       if (ctlr_mask == 0) {
+                               printf("Error: controller number not "
+                                       "specified or no element and "
+                                       "value specified\n");
+                               continue;
+                       }
+
+                       if (ctlr_mask & (ctlr_mask - 1)) {
+                               printf("Error: multiple controllers "
+                                               "specified, %X\n", ctlr_mask);
+                               continue;
+                       }
+
+                       /* ERROR: DIMM number not specified */
+                       if (dimm_number_required && dimm_mask == 0) {
+                               printf("Error: DIMM number number not "
+                                       "specified or no element and "
+                                       "value specified\n");
+                               continue;
+                       }
+
+                       if (dimm_mask & (dimm_mask - 1)) {
+                               printf("Error: multipled DIMMs specified\n");
+                               continue;
+                       }
+
+                       p_element = argv[argc - 2];
+                       p_value = argv[argc - 1];
+
+                       ctrl_num = __ilog2(ctlr_mask);
+                       dimm_num = __ilog2(dimm_mask);
+
+                       switch (step_mask) {
+                       case STEP_GET_SPD:
+                               {
+                                       unsigned int element_num;
+                                       unsigned int value;
+
+                                       element_num = simple_strtoul(p_element,
+                                                                    NULL, 0);
+                                       value = simple_strtoul(p_value,
+                                                              NULL, 0);
+                                       fsl_ddr_spd_edit(pinfo,
+                                                              ctrl_num,
+                                                              dimm_num,
+                                                              element_num,
+                                                              value);
+                                       next_step = STEP_COMPUTE_DIMM_PARMS;
+                               }
+                               break;
+
+                       case STEP_COMPUTE_DIMM_PARMS:
+                               fsl_ddr_dimm_parameters_edit(
+                                                pinfo, ctrl_num, dimm_num,
+                                                p_element, p_value);
+                               next_step = STEP_COMPUTE_COMMON_PARMS;
+                               break;
+
+                       case STEP_COMPUTE_COMMON_PARMS:
+                               lowest_common_dimm_parameters_edit(pinfo,
+                                               ctrl_num, p_element, p_value);
+                               next_step = STEP_GATHER_OPTS;
+                               break;
+
+                       case STEP_GATHER_OPTS:
+                               fsl_ddr_options_edit(pinfo, ctrl_num,
+                                                          p_element, p_value);
+                               next_step = STEP_ASSIGN_ADDRESSES;
+                               break;
+
+                       case STEP_ASSIGN_ADDRESSES:
+                               printf("editing of address assignment "
+                                               "not yet implemented\n");
+                               break;
+
+                       case STEP_COMPUTE_REGS:
+                               {
+                                       fsl_ddr_regs_edit(pinfo,
+                                                               ctrl_num,
+                                                               p_element,
+                                                               p_value);
+                                       next_step = STEP_PROGRAM_REGS;
+                               }
+                               break;
+
+                       default:
+                               printf("programming error\n");
+                               while (1)
+                                       ;
+                               break;
+                       }
+                       continue;
+               }
+
+               if (strcmp(argv[0], "reset") == 0) {
+                       /*
+                        * Reboot machine.
+                        * Args don't seem to matter because this
+                        * doesn't return
+                        */
+                       do_reset(NULL, 0, 0, NULL);
+               }
+
+               if (strcmp(argv[0], "recompute") == 0) {
+                       /*
+                        * Recalculate everything, starting with
+                        * loading SPD EEPROM from DIMMs
+                        */
+                       next_step = STEP_GET_SPD;
+                       ddrsize = fsl_ddr_compute(pinfo, next_step, 0);
+                       continue;
+               }
+
+               if (strcmp(argv[0], "compute") == 0) {
+                       /*
+                        * Compute rest of steps starting at
+                        * the current next_step/
+                        */
+                       ddrsize = fsl_ddr_compute(pinfo, next_step, 0);
+                       continue;
+               }
+
+               if (strcmp(argv[0], "print") == 0) {
+                       unsigned int i, j;
+                       unsigned int error = 0;
+                       unsigned int step_mask = 0;
+                       unsigned int ctlr_mask = 0;
+                       unsigned int dimm_mask = 0;
+                       unsigned int matched = 0;
+
+                       if (argc == 1) {
+                               printf("print [c<n>] [d<n>] [spd] [dimmparms] "
+                                 "[commonparms] [opts] [addresses] [regs]\n");
+                               continue;
+                       }
+
+                       for (i = 1; i < argc; i++) {
+                               for (j = 0; j < n_opts; j++) {
+                                       if (strcmp(options[j].data_name,
+                                               argv[i]) != 0)
+                                               continue;
+                                       step_mask |= options[j].step_mask;
+                                       matched = 1;
+                                       break;
+                               }
+
+                               if (matched)
+                                       continue;
+
+                               if (argv[i][0] == 'c') {
+                                       char c = argv[i][1];
+                                       if (isdigit(c))
+                                               ctlr_mask |= 1 << (c - '0');
+                                       continue;
+                               }
+
+                               if (argv[i][0] == 'd') {
+                                       char c = argv[i][1];
+                                       if (isdigit(c))
+                                               dimm_mask |= 1 << (c - '0');
+                                       continue;
+                               }
+
+                               printf("unknown arg %s\n", argv[i]);
+                               step_mask = 0;
+                               error = 1;
+                               break;
+                       }
+
+                       if (error)
+                               continue;
+
+                       /* If no particular controller was found, print all */
+                       if (ctlr_mask == 0)
+                               ctlr_mask = 0xFF;
+
+                       /* If no particular dimm was found, print all dimms. */
+                       if (dimm_mask == 0)
+                               dimm_mask = 0xFF;
+
+                       /* If no steps were found, print all steps. */
+                       if (step_mask == 0)
+                               step_mask = STEP_ALL;
+
+                       fsl_ddr_printinfo(pinfo, ctlr_mask,
+                                               dimm_mask, step_mask);
+                       continue;
+               }
+
+               if (strcmp(argv[0], "go") == 0) {
+                       if (next_step)
+                               ddrsize = fsl_ddr_compute(pinfo, next_step, 0);
+                       break;
+               }
+
+               printf("unknown command %s\n", argv[0]);
+       }
+
+       debug("end of memory = %llu\n", (u64)ddrsize);
+
+       return ddrsize;
+}
index 5699b0c2cc9a287ce7f4dc287b6a292ef40c32ad..f52ad9f6910296bee17f3fd60c0e473b4181b1a9 100644 (file)
@@ -135,7 +135,6 @@ void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd,
  *                             |  interleaving
  */
 
-#ifdef DEBUG
 const char *step_string_tbl[] = {
        "STEP_GET_SPD",
        "STEP_COMPUTE_DIMM_PARMS",
@@ -156,7 +155,6 @@ const char * step_to_string(unsigned int step) {
 
        return step_string_tbl[s];
 }
-#endif
 
 int step_assign_addresses(fsl_ddr_info_t *pinfo,
                          unsigned int dbw_cap_adj[],
@@ -499,7 +497,12 @@ phys_size_t fsl_ddr_sdram(void)
        memset(&info, 0, sizeof(fsl_ddr_info_t));
 
        /* Compute it once normally. */
-       total_memory = fsl_ddr_compute(&info, STEP_GET_SPD, 0);
+#ifdef CONFIG_FSL_DDR_INTERACTIVE
+       if (getenv("ddr_interactive"))
+               total_memory = fsl_ddr_interactive(&info);
+       else
+#endif
+               total_memory = fsl_ddr_compute(&info, STEP_GET_SPD, 0);
 
        /* Check for memory controller interleaving. */
        memctl_interleaved = 0;
index abfb7f192de3e450dd000a501bf818f170e3375a..1d50153d58c2a4802f1b48fcd8f7291734f98cf5 100644 (file)
@@ -222,3 +222,153 @@ Single slot system
 
 Reference http://www.samsung.com/global/business/semiconductor/products/dram/downloads/applicationnote/ddr2_odt_control_200603.pdf
 
+
+Interactive DDR debugging
+===========================
+
+For DDR parameter tuning up and debugging, the interactive DDR debugging can
+be activated by saving an environment variable "ddr_interactive". The value
+doesn't matter. Once activated, U-boot prompts "FSL DDR>" before enabling DDR
+controller. The available commands can be seen by typing "help".
+
+The example flow of using interactive debugging is
+type command "compute" to calculate the parameters from the default
+type command "print" with arguments to show SPD, options, registers
+type command "edit" with arguments to change any if desired
+type command "go" to continue calculation and enable DDR controller
+type command "reset" to reset the board
+type command "recompute" to reload SPD and start over
+
+Note, check "next_step" to show the flow. For example, after edit opts, the
+next_step is STEP_ASSIGN_ADDRESSES. After editing registers, the next_step is
+STEP_PROGRAM_REGS. Upon issuing command "go", DDR controller will be enabled
+with current setting without further calculation.
+
+The detail syntax for each commands are
+
+print [c<n>] [d<n>] [spd] [dimmparms] [commonparms] [opts] [addresses] [regs]
+       c<n>            - the controller number, eg. c0, c1
+       d<n>            - the DIMM number, eg. d0, d1
+       spd             - print SPD data
+       dimmparms       - DIMM paramaters, calcualted from SPD
+       commonparms     - lowest common parameters for all DIMMs
+       opts            - options
+       addresses       - address assignment (not implemented yet)
+       regs            - controller registers
+
+edit <c#> <d#> <spd|dimmparms|commonparms|opts|addresses|regs> <element> <value>
+       c<n>            - the controller number, eg. c0, c1
+       d<n>            - the DIMM number, eg. d0, d1
+       spd             - print SPD data
+       dimmparms       - DIMM paramaters, calcualted from SPD
+       commonparms     - lowest common parameters for all DIMMs
+       opts            - options
+       addresses       - address assignment (not implemented yet)
+       regs            - controller registers
+       <element>       - name of the modified element
+                         byte number if the object is SPD
+       <value>         - decimal or heximal (prefixed with 0x) numbers
+
+reset
+       no arguement    - reset the board
+
+recompute
+       no argument     - reload SPD and start over
+
+compute
+       no argument     - recompute from current next_step
+
+next_step
+       no argument     - show current next_step
+
+help
+       no argument     - print a list of all commands
+
+go
+       no argument     - program memory controller(s) and continue with U-boot
+
+Examples of debugging flow
+
+       FSL DDR>compute
+       Detected UDIMM UG51U6400N8SU-ACF
+       SL DDR>print
+       print [c<n>] [d<n>] [spd] [dimmparms] [commonparms] [opts] [addresses] [regs]
+       FSL DDR>print dimmparms
+       DIMM parameters:  Controller=0 DIMM=0
+       DIMM organization parameters:
+       module part name = UG51U6400N8SU-ACF
+       rank_density = 2147483648 bytes (2048 megabytes)
+       capacity = 4294967296 bytes (4096 megabytes)
+       burst_lengths_bitmask = 0C
+       base_addresss = 0 (00000000 00000000)
+       n_ranks = 2
+       data_width = 64
+       primary_sdram_width = 64
+       ec_sdram_width = 0
+       registered_dimm = 0
+       n_row_addr = 15
+       n_col_addr = 10
+       edc_config = 0
+       n_banks_per_sdram_device = 8
+       tCKmin_X_ps = 1500
+       tCKmin_X_minus_1_ps = 0
+       tCKmin_X_minus_2_ps = 0
+       tCKmax_ps = 0
+       caslat_X = 960
+       tAA_ps = 13125
+       caslat_X_minus_1 = 0
+       caslat_X_minus_2 = 0
+       caslat_lowest_derated = 0
+       tRCD_ps = 13125
+       tRP_ps = 13125
+       tRAS_ps = 36000
+       tWR_ps = 15000
+       tWTR_ps = 7500
+       tRFC_ps = 160000
+       tRRD_ps = 6000
+       tRC_ps = 49125
+       refresh_rate_ps = 7800000
+       tIS_ps = 0
+       tIH_ps = 0
+       tDS_ps = 0
+       tDH_ps = 0
+       tRTP_ps = 7500
+       tDQSQ_max_ps = 0
+       tQHS_ps = 0
+       FSL DDR>edit c0 opts ECC_mode 0
+       FSL DDR>edit c0 regs cs0_bnds 0x000000FF
+       FSL DDR>go
+       2 GiB left unmapped
+       4 GiB (DDR3, 64-bit, CL=9, ECC off)
+              DDR Chip-Select Interleaving Mode: CS0+CS1
+       Testing 0x00000000 - 0x7fffffff
+       Testing 0x80000000 - 0xffffffff
+       Remap DDR 2 GiB left unmapped
+
+       POST memory PASSED
+       Flash: 128 MiB
+       L2:    128 KB enabled
+       Corenet Platform Cache: 1024 KB enabled
+       SERDES: timeout resetting bank 3
+       SRIO1: disabled
+       SRIO2: disabled
+       MMC:  FSL_ESDHC: 0
+       EEPROM: Invalid ID (ff ff ff ff)
+       PCIe1: disabled
+       PCIe2: Root Complex, x1, regs @ 0xfe201000
+         01:00.0     - 8086:10d3 - Network controller
+       PCIe2: Bus 00 - 01
+       PCIe3: disabled
+       In:    serial
+       Out:   serial
+       Err:   serial
+       Net:   Initializing Fman
+       Fman1: Uploading microcode version 101.8.0
+       e1000: 00:1b:21:81:d2:e0
+       FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5, e1000#0 [PRIME]
+       Warning: e1000#0 MAC addresses don't match:
+       Address in SROM is         00:1b:21:81:d2:e0
+       Address in environment is  00:e0:0c:00:ea:05
+
+       Hit any key to stop autoboot:  0
+       =>
index b9b89cfa5dca84274267e3f4dca4800ec4422f33..f1ef1df18314cbffe69d7227c921b12c59bea2d1 100644 (file)
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_SPD_BUS_NUM 1
 #define SPD_EEPROM_ADDRESS 0x52
-#define CONFIG_FSL_DDR_INTERACTIVE
+#undef CONFIG_FSL_DDR_INTERACTIVE
 
 #ifdef CONFIG_P1020MBG
 #define CONFIG_SYS_SDRAM_SIZE_LAW      LAW_SIZE_2G