config CMD_PINMON
bool "Enable boot mode pins monitor command"
- depends on !SPL_BUILD
default y
help
The command "pinmon" shows the state of the boot mode pins.
The boot mode pins are latched when the system reset is deasserted
and determine which device the system should load a boot image from.
-config SOC_INIT
- bool
- default SPL_BUILD
-
-config DRAM_INIT
- bool
- default SPL_BUILD
-
config CMD_DDRPHY_DUMP
bool "Enable dump command of DDR PHY parameters"
depends on !SPL_BUILD
choice
prompt "DDR3 Frequency select"
- depends on DRAM_INIT
+ depends on SPL_BUILD
config DDR_FREQ_1600
bool "DDR3 1600"
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_SPL_BUILD) += lowlevel_init.o init_page_table.o
-obj-$(CONFIG_SPL_BUILD) += spl.o
+ifdef CONFIG_SPL_BUILD
+
+obj-y += lowlevel_init.o
+obj-y += init_page_table.o
+obj-y += spl.o
+obj-y += ddrphy_training.o
+
+else
-obj-y += timer.o
-obj-y += reset.o
-obj-y += cache_uniphier.o
-obj-y += dram_init.o
-obj-$(CONFIG_DRAM_INIT) += ddrphy_training.o
obj-$(CONFIG_BOARD_EARLY_INIT_F) += board_early_init_f.o
obj-$(CONFIG_DISPLAY_CPUINFO) += cpu_info.o
obj-$(CONFIG_MISC_INIT_F) += print_misc_info.o
+obj-y += dram_init.o
+obj-y += board_common.o
obj-$(CONFIG_BOARD_EARLY_INIT_R) += board_early_init_r.o
obj-$(CONFIG_BOARD_LATE_INIT) += board_late_init.o
+obj-y += reset.o
+obj-y += cache_uniphier.o
obj-$(CONFIG_UNIPHIER_SMP) += smp.o
obj-$(CONFIG_CMD_PINMON) += cmd_pinmon.o
obj-$(CONFIG_CMD_DDRPHY_DUMP) += cmd_ddrphy.o
-obj-y += board_common.o
+endif
+
+obj-y += timer.o
+
obj-$(CONFIG_PFC_MICRO_SUPPORT_CARD) += support_card.o
obj-$(CONFIG_DCC_MICRO_SUPPORT_CARD) += support_card.o
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(if $(CONFIG_OF_CONTROL),,y) += platdevice.o
-obj-y += boot-mode.o
+ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_DEBUG_LL) += lowlevel_debug.o
-obj-$(CONFIG_SOC_INIT) += bcu_init.o sbc_init.o sg_init.o pll_init.o \
- clkrst_init.o
+obj-y += bcu_init.o sbc_init.o sg_init.o pll_init.o clkrst_init.o \
+ pll_spectrum.o umc_init.o ddrphy_init.o
+else
obj-$(CONFIG_BOARD_EARLY_INIT_F) += pinctrl.o
-obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o ddrphy_init.o
+obj-$(if $(CONFIG_OF_CONTROL),,y) += platdevice.o
+endif
+
+obj-y += boot-mode.o
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(if $(CONFIG_OF_CONTROL),,y) += platdevice.o
-obj-y += boot-mode.o
+ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_DEBUG_LL) += lowlevel_debug.o
-obj-$(CONFIG_SOC_INIT) += sbc_init.o sg_init.o pll_init.o clkrst_init.o
+obj-y += sbc_init.o sg_init.o pll_init.o clkrst_init.o \
+ pll_spectrum.o umc_init.o ddrphy_init.o
+else
obj-$(CONFIG_BOARD_EARLY_INIT_F) += pinctrl.o
-obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o ddrphy_init.o
+obj-$(if $(CONFIG_OF_CONTROL),,y) += platdevice.o
+endif
+
+obj-y += boot-mode.o
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(if $(CONFIG_OF_CONTROL),,y) += platdevice.o
-obj-y += boot-mode.o
+ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_DEBUG_LL) += lowlevel_debug.o
-obj-$(CONFIG_SOC_INIT) += bcu_init.o sbc_init.o sg_init.o pll_init.o \
- clkrst_init.o
+obj-y += bcu_init.o sbc_init.o sg_init.o pll_init.o clkrst_init.o \
+ pll_spectrum.o umc_init.o ddrphy_init.o
+else
obj-$(CONFIG_BOARD_EARLY_INIT_F) += pinctrl.o
-obj-$(CONFIG_DRAM_INIT) += pll_spectrum.o umc_init.o ddrphy_init.o
+obj-$(if $(CONFIG_OF_CONTROL),,y) += platdevice.o
+endif
+
+obj-y += boot-mode.o
projects / u-boot.git / commitdiff