Sync all J7200 related v5.11-rc6 Linux kernel dts into U-Boot.
MCU R5F nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid regressions, r5f nodes are kept intact.
These will be added in kernel in future.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
aliases {
ethernet0 = &cpsw_port1;
+ i2c0 = &wkup_i2c0;
+ i2c1 = &mcu_i2c0;
+ i2c2 = &mcu_i2c1;
+ i2c3 = &main_i2c0;
};
};
-&chipid {
- u-boot,dm-spl;
-};
-
&cbass_main {
u-boot,dm-spl;
};
clock-frequency = <25000000>;
u-boot,dm-spl;
};
+
+ chipid@43000014 {
+ u-boot,dm-spl;
+ };
};
&secure_proxy_main {
u-boot,dm-spl;
};
-&wkup_gpio0 {
- u-boot,dm-spl;
-};
-
&mcu_fss0_hpb0_pins_default {
u-boot,dm-spl;
};
/dts-v1/;
-#include <dt-bindings/net/ti-dp83867.h>
#include "k3-j7200-som-p0.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/mux/ti-serdes.h>
/ {
chosen {
>;
};
- mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+ mcu_cpsw_pins_default: mcu-cpsw-pins-default {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
>;
};
- mcu_mdio_pins_default: mcu_mdio1_pins_default {
+ mcu_mdio_pins_default: mcu-mdio1-pins-default {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>;
};
- main_mmc1_pins_default: main_mmc1_pins_default {
+ main_i2c1_pins_default: main-i2c1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
+ J721E_IOPAD(0xe0, PIN_INPUT_PULLUP, 3) /* (T3) EXT_REFCLK1.I2C1_SDA */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0x104, PIN_INPUT, 0) /* (M20) MMC1_CMD */
J721E_IOPAD(0x100, PIN_INPUT, 0) /* (P21) MMC1_CLK */
>;
};
- main_usbss0_pins_default: main_usbss0_pins_default {
+ main_usbss0_pins_default: main-usbss0-pins-default {
pinctrl-single,pins = <
J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>;
&wkup_uart0 {
/* Wakeup UART is used by System firmware */
- status = "disabled";
+ status = "reserved";
};
&main_uart0 {
+ /* Shared with ATF on this platform */
power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
};
&main_uart2 {
/* MAIN UART 2 is used by R5F firmware */
- status = "disabled";
+ status = "reserved";
};
&main_uart3 {
status = "disabled";
};
-&wkup_i2c0 {
+&mcu_cpsw {
pinctrl-names = "default";
- pinctrl-0 = <&wkup_i2c0_pins_default>;
- clock-frequency = <400000>;
+ pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
};
-&main_sdhci0 {
- /* eMMC */
- non-removable;
- ti,driver-strength-ohm = <50>;
- disable-wp;
+&davinci_mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ };
};
-&main_sdhci1 {
- /* SD card */
- pinctrl-0 = <&main_mmc1_pins_default>;
- pinctrl-names = "default";
- vmmc-supply = <&vdd_mmc1>;
- vqmmc-supply = <&vdd_sd_dv>;
- ti,driver-strength-ohm = <50>;
- disable-wp;
+&cpsw_port1 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&phy0>;
};
&main_i2c0 {
};
};
-&usbss0 {
+/*
+ * The j7200 CPB board is identical to the CPB used for J721E, the SOMs can be
+ * swapped on the CPB.
+ *
+ * main_i2c1 of J7200 is connected to the CPB i2c bus labeled as i2c3.
+ * The i2c1 of the CPB (as it is labeled) is not connected to j7200.
+ */
+&main_i2c1 {
pinctrl-names = "default";
- pinctrl-0 = <&main_usbss0_pins_default>;
- ti,vbus-divider;
- ti,usb2-only;
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ clock-frequency = <400000>;
+
+ exp3: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "CODEC_RSTz", "CODEC_SPARE1", "UB926_RESETn",
+ "UB926_LOCK", "UB926_PWR_SW_CNTRL",
+ "UB926_TUNER_RESET", "UB926_GPIO_SPARE", "";
+ };
};
-&usb0 {
- dr_mode = "otg";
- maximum-speed = "high-speed";
+&main_sdhci0 {
+ /* eMMC */
+ non-removable;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
};
-&wkup_gpio0 {
+&main_sdhci1 {
+ /* SD card */
+ pinctrl-0 = <&main_mmc1_pins_default>;
pinctrl-names = "default";
- pinctrl-0 = <&wkup_gpio_pins_default>;
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
};
-&mcu_cpsw {
+&serdes_ln_ctrl {
+ idle-states = <J7200_SERDES0_LANE0_PCIE1_LANE0>, <J7200_SERDES0_LANE1_PCIE1_LANE1>,
+ <J7200_SERDES0_LANE2_QSGMII_LANE1>, <J7200_SERDES0_LANE3_IP4_UNUSED>;
+};
+
+&usb_serdes_mux {
+ idle-states = <1>; /* USB0 to SERDES lane 3 */
+};
+
+&usbss0 {
pinctrl-names = "default";
- pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
+ pinctrl-0 = <&main_usbss0_pins_default>;
+ ti,vbus-divider;
+ ti,usb2-only;
};
-&davinci_mdio {
- phy0: ethernet-phy@0 {
- reg = <0>;
- ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
- ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
- };
+&usb0 {
+ dr_mode = "otg";
+ maximum-speed = "high-speed";
};
-&cpsw_port1 {
- phy-mode = "rgmii-rxid";
- phy-handle = <&phy0>;
+&tscadc0 {
+ adc {
+ ti,adc-channels = <0 1 2 3 4 5 6 7>;
+ };
};
&cbass_main {
msmc_ram: sram@70000000 {
compatible = "mmio-sram";
- reg = <0x0 0x70000000 0x0 0x100000>;
+ reg = <0x00 0x70000000 0x00 0x100000>;
#address-cells = <1>;
#size-cells = <1>;
- ranges = <0x0 0x0 0x70000000 0x100000>;
+ ranges = <0x00 0x00 0x70000000 0x100000>;
atf-sram@0 {
- reg = <0x0 0x20000>;
+ reg = <0x00 0x20000>;
+ };
+ };
+
+ scm_conf: scm-conf@100000 {
+ compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+ reg = <0x00 0x00100000 0x00 0x1c000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x00 0x00 0x00100000 0x1c000>;
+
+ serdes_ln_ctrl: serdes-ln-ctrl@4080 {
+ compatible = "mmio-mux";
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
+ <0x4088 0x3>, <0x408c 0x3>; /* SERDES0 lane2/3 select */
+ };
+
+ usb_serdes_mux: mux-controller@4000 {
+ compatible = "mmio-mux";
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x4000 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
};
};
};
};
- main_navss: navss@30000000 {
+ main_gpio_intr: interrupt-controller0 {
+ compatible = "ti,sci-intr";
+ ti,intr-trigger-type = <1>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ #interrupt-cells = <1>;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <131>;
+ ti,interrupt-ranges = <8 392 56>;
+ };
+
+ main_navss: bus@30000000 {
compatible = "simple-mfd";
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>;
+ ti,sci-dev-id = <199>;
+
+ main_navss_intr: interrupt-controller1 {
+ compatible = "ti,sci-intr";
+ ti,intr-trigger-type = <4>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ #interrupt-cells = <1>;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <213>;
+ ti,interrupt-ranges = <0 64 64>,
+ <64 448 64>,
+ <128 672 64>;
+ };
+
+ main_udmass_inta: msi-controller@33d00000 {
+ compatible = "ti,sci-inta";
+ reg = <0x00 0x33d00000 0x00 0x100000>;
+ interrupt-controller;
+ #interrupt-cells = <0>;
+ interrupt-parent = <&main_navss_intr>;
+ msi-controller;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <209>;
+ ti,interrupt-ranges = <0 0 256>;
+ };
secure_proxy_main: mailbox@32c00000 {
compatible = "ti,am654-secure-proxy";
interrupt-names = "rx_011";
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
};
+
+ hwspinlock: spinlock@30e00000 {
+ compatible = "ti,am654-hwspinlock";
+ reg = <0x00 0x30e00000 0x00 0x1000>;
+ #hwlock-cells = <1>;
+ };
+
+ mailbox0_cluster0: mailbox@31f80000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f80000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster1: mailbox@31f81000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f81000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster2: mailbox@31f82000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f82000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster3: mailbox@31f83000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f83000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster4: mailbox@31f84000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f84000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster5: mailbox@31f85000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f85000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster6: mailbox@31f86000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f86000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster7: mailbox@31f87000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f87000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster8: mailbox@31f88000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f88000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster9: mailbox@31f89000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f89000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster10: mailbox@31f8a000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f8a000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ mailbox0_cluster11: mailbox@31f8b000 {
+ compatible = "ti,am654-mailbox";
+ reg = <0x00 0x31f8b000 0x00 0x200>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ interrupt-parent = <&main_navss_intr>;
+ };
+
+ main_ringacc: ringacc@3c000000 {
+ compatible = "ti,am654-navss-ringacc";
+ reg = <0x00 0x3c000000 0x00 0x400000>,
+ <0x00 0x38000000 0x00 0x400000>,
+ <0x00 0x31120000 0x00 0x100>,
+ <0x00 0x33000000 0x00 0x40000>;
+ reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
+ ti,num-rings = <1024>;
+ ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <211>;
+ msi-parent = <&main_udmass_inta>;
+ };
+
+ main_udmap: dma-controller@31150000 {
+ compatible = "ti,j721e-navss-main-udmap";
+ reg = <0x00 0x31150000 0x00 0x100>,
+ <0x00 0x34000000 0x00 0x100000>,
+ <0x00 0x35000000 0x00 0x100000>;
+ reg-names = "gcfg", "rchanrt", "tchanrt";
+ msi-parent = <&main_udmass_inta>;
+ #dma-cells = <1>;
+
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <212>;
+ ti,ringacc = <&main_ringacc>;
+
+ ti,sci-rm-range-tchan = <0x0d>, /* TX_CHAN */
+ <0x0f>, /* TX_HCHAN */
+ <0x10>; /* TX_UHCHAN */
+ ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
+ <0x0b>, /* RX_HCHAN */
+ <0x0c>; /* RX_UHCHAN */
+ ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+ };
+
+ cpts@310d0000 {
+ compatible = "ti,j721e-cpts";
+ reg = <0x00 0x310d0000 0x00 0x400>;
+ reg-names = "cpts";
+ clocks = <&k3_clks 201 1>;
+ clock-names = "cpts";
+ interrupts-extended = <&main_navss_intr 391>;
+ interrupt-names = "cpts";
+ ti,cpts-periodic-outputs = <6>;
+ ti,cpts-ext-ts-inputs = <8>;
+ };
};
- main_pmx0: pinmux@11c000 {
+ main_pmx0: pinctrl@11c000 {
compatible = "pinctrl-single";
/* Proxy 0 addressing */
- reg = <0x0 0x11c000 0x0 0x2b4>;
+ reg = <0x00 0x11c000 0x00 0x2b4>;
#pinctrl-cells = <1>;
pinctrl-single,register-width = <32>;
pinctrl-single,function-mask = <0xffffffff>;
clock-names = "fclk";
};
- main_gpio0: gpio@600000 {
- compatible = "ti,j721e-gpio", "ti,keystone-gpio";
- reg = <0x0 0x00600000 0x0 0x100>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupts = <105 0 IRQ_TYPE_EDGE_RISING>,
- <105 1 IRQ_TYPE_EDGE_RISING>,
- <105 2 IRQ_TYPE_EDGE_RISING>,
- <105 3 IRQ_TYPE_EDGE_RISING>,
- <105 4 IRQ_TYPE_EDGE_RISING>,
- <105 5 IRQ_TYPE_EDGE_RISING>,
- <105 6 IRQ_TYPE_EDGE_RISING>,
- <105 7 IRQ_TYPE_EDGE_RISING>;
- interrupt-controller;
- #interrupt-cells = <2>;
- ti,ngpio = <69>;
- ti,davinci-gpio-unbanked = <0>;
- power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
- clocks = <&k3_clks 105 0>;
- clock-names = "gpio";
- };
-
main_sdhci0: sdhci@4f80000 {
compatible = "ti,j721e-sdhci-8bit";
reg = <0x0 0x04f80000 0x0 0x260>, <0x0 0x4f88000 0x0 0x134>;
main_i2c0: i2c@2000000 {
compatible = "ti,j721e-i2c", "ti,omap4-i2c";
- reg = <0x0 0x2000000 0x0 0x100>;
+ reg = <0x00 0x2000000 0x00 0x100>;
interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
clock-names = "fck";
clocks = <&k3_clks 187 1>;
- power-domains = <&k3_pds 187 TI_SCI_PD_EXCLUSIVE>;
+ power-domains = <&k3_pds 187 TI_SCI_PD_SHARED>;
};
main_i2c1: i2c@2010000 {
compatible = "ti,j721e-i2c", "ti,omap4-i2c";
- reg = <0x0 0x2010000 0x0 0x100>;
+ reg = <0x00 0x2010000 0x00 0x100>;
interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
main_i2c2: i2c@2020000 {
compatible = "ti,j721e-i2c", "ti,omap4-i2c";
- reg = <0x0 0x2020000 0x0 0x100>;
+ reg = <0x00 0x2020000 0x00 0x100>;
interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
main_i2c3: i2c@2030000 {
compatible = "ti,j721e-i2c", "ti,omap4-i2c";
- reg = <0x0 0x2030000 0x0 0x100>;
+ reg = <0x00 0x2030000 0x00 0x100>;
interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
main_i2c4: i2c@2040000 {
compatible = "ti,j721e-i2c", "ti,omap4-i2c";
- reg = <0x0 0x2040000 0x0 0x100>;
+ reg = <0x00 0x2040000 0x00 0x100>;
interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
main_i2c5: i2c@2050000 {
compatible = "ti,j721e-i2c", "ti,omap4-i2c";
- reg = <0x0 0x2050000 0x0 0x100>;
+ reg = <0x00 0x2050000 0x00 0x100>;
interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
main_i2c6: i2c@2060000 {
compatible = "ti,j721e-i2c", "ti,omap4-i2c";
- reg = <0x0 0x2060000 0x0 0x100>;
+ reg = <0x00 0x2060000 0x00 0x100>;
interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&k3_pds 193 TI_SCI_PD_EXCLUSIVE>;
};
- usbss0: cdns_usb@4104000 {
+ main_gpio0: gpio@600000 {
+ compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+ reg = <0x0 0x00600000 0x0 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <105 0 IRQ_TYPE_EDGE_RISING>,
+ <105 1 IRQ_TYPE_EDGE_RISING>,
+ <105 2 IRQ_TYPE_EDGE_RISING>,
+ <105 3 IRQ_TYPE_EDGE_RISING>,
+ <105 4 IRQ_TYPE_EDGE_RISING>,
+ <105 5 IRQ_TYPE_EDGE_RISING>,
+ <105 6 IRQ_TYPE_EDGE_RISING>,
+ <105 7 IRQ_TYPE_EDGE_RISING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,ngpio = <69>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 105 0>;
+ clock-names = "gpio";
+ };
+
+ usbss0: cdns-usb@4104000 {
compatible = "ti,j721e-usb";
reg = <0x00 0x4104000 0x00 0x100>;
dma-coherent;
power-domains = <&k3_pds 288 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 288 12>, <&k3_clks 288 3>;
- clock-names = "usb2_refclk", "lpm_clk";
+ clock-names = "ref", "lpm";
assigned-clocks = <&k3_clks 288 12>; /* USB2_REFCLK */
assigned-clock-parents = <&k3_clks 288 13>; /* HFOSC0 */
#address-cells = <2>;
<&secure_proxy_main 13>;
reg-names = "debug_messages";
- reg = <0x00 0x44083000 0x0 0x1000>;
+ reg = <0x00 0x44083000 0x00 0x1000>;
k3_pds: power-controller {
compatible = "ti,sci-pm-domain";
};
};
- chipid: chipid@43000014 {
+ mcu_conf: syscon@40f00000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x00 0x40f00000 0x00 0x20000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x00 0x00 0x40f00000 0x20000>;
+
+ phy_gmii_sel: phy@4040 {
+ compatible = "ti,am654-phy-gmii-sel";
+ reg = <0x4040 0x4>;
+ #phy-cells = <1>;
+ };
+ };
+
+ chipid@43000014 {
compatible = "ti,am654-chipid";
- reg = <0x0 0x43000014 0x0 0x4>;
+ reg = <0x00 0x43000014 0x00 0x4>;
};
- wkup_pmx0: pinmux@4301c000 {
+ wkup_pmx0: pinctrl@4301c000 {
compatible = "pinctrl-single";
/* Proxy 0 addressing */
reg = <0x00 0x4301c000 0x00 0x178>;
mcu_ram: sram@41c00000 {
compatible = "mmio-sram";
reg = <0x00 0x41c00000 0x00 0x100000>;
- ranges = <0x0 0x00 0x41c00000 0x100000>;
+ ranges = <0x00 0x00 0x41c00000 0x100000>;
#address-cells = <1>;
#size-cells = <1>;
};
clock-names = "fclk";
};
- wkup_i2c0: i2c@42120000 {
- compatible = "ti,j721e-i2c", "ti,omap4-i2c";
- reg = <0x0 0x42120000 0x0 0x100>;
- interrupts = <GIC_SPI 896 IRQ_TYPE_LEVEL_HIGH>;
- #address-cells = <1>;
- #size-cells = <0>;
- clock-names = "fck";
- clocks = <&k3_clks 197 1>;
- power-domains = <&k3_pds 197 TI_SCI_PD_EXCLUSIVE>;
- };
-
mcu_uart0: serial@40a00000 {
compatible = "ti,j721e-uart", "ti,am654-uart";
reg = <0x00 0x40a00000 0x00 0x100>;
clock-names = "fclk";
};
- fss: system-controller@47000000 {
- compatible = "syscon", "simple-mfd";
- reg = <0x0 0x47000000 0x0 0x100>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- hbmc_mux: hbmc-mux {
- compatible = "mmio-mux";
- #mux-control-cells = <1>;
- mux-reg-masks = <0x4 0x2>; /* HBMC select */
- };
-
- hbmc: hyperbus@47034000 {
- compatible = "ti,am654-hbmc";
- reg = <0x0 0x47034000 0x0 0x100>,
- <0x5 0x00000000 0x1 0x0000000>;
- power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
- #address-cells = <2>;
- #size-cells = <1>;
- mux-controls = <&hbmc_mux 0>;
- clocks = <&k3_clks 102 5>;
- assigned-clocks = <&k3_clks 102 5>;
- assigned-clock-rates = <333333333>;
- };
- };
-
- mcu_i2c0: i2c@40b00000 {
- compatible = "ti,j721e-i2c", "ti,omap4-i2c";
- reg = <0x0 0x40b00000 0x0 0x100>;
- interrupts = <GIC_SPI 852 IRQ_TYPE_LEVEL_HIGH>;
- #address-cells = <1>;
- #size-cells = <0>;
- clock-names = "fck";
- clocks = <&k3_clks 194 1>;
- power-domains = <&k3_pds 194 TI_SCI_PD_EXCLUSIVE>;
- };
-
- mcu_i2c1: i2c@40b10000 {
- compatible = "ti,j721e-i2c", "ti,omap4-i2c";
- reg = <0x0 0x40b10000 0x0 0x100>;
- interrupts = <GIC_SPI 853 IRQ_TYPE_LEVEL_HIGH>;
- #address-cells = <1>;
- #size-cells = <0>;
- clock-names = "fck";
- clocks = <&k3_clks 195 1>;
- power-domains = <&k3_pds 195 TI_SCI_PD_EXCLUSIVE>;
+ wkup_gpio_intr: interrupt-controller2 {
+ compatible = "ti,sci-intr";
+ ti,intr-trigger-type = <1>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ #interrupt-cells = <1>;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <137>;
+ ti,interrupt-ranges = <16 960 16>;
};
- cbass_mcu_navss: mcu-navss {
+ mcu_navss: bus@28380000 {
compatible = "simple-mfd";
#address-cells = <2>;
#size-cells = <2>;
- ranges;
+ ranges = <0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>;
dma-coherent;
dma-ranges;
-
ti,sci-dev-id = <232>;
mcu_ringacc: ringacc@2b800000 {
compatible = "ti,am654-navss-ringacc";
- reg = <0x0 0x2b800000 0x0 0x400000>,
- <0x0 0x2b000000 0x0 0x400000>,
- <0x0 0x28590000 0x0 0x100>,
- <0x0 0x2a500000 0x0 0x40000>;
+ reg = <0x00 0x2b800000 0x00 0x400000>,
+ <0x00 0x2b000000 0x00 0x400000>,
+ <0x00 0x28590000 0x00 0x100>,
+ <0x00 0x2a500000 0x00 0x40000>;
reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
ti,num-rings = <286>;
ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */
ti,sci = <&dmsc>;
ti,sci-dev-id = <235>;
+ msi-parent = <&main_udmass_inta>;
};
mcu_udmap: dma-controller@285c0000 {
compatible = "ti,j721e-navss-mcu-udmap";
- reg = <0x0 0x285c0000 0x0 0x100>,
- <0x0 0x2a800000 0x0 0x40000>,
- <0x0 0x2aa00000 0x0 0x40000>;
+ reg = <0x00 0x285c0000 0x00 0x100>,
+ <0x00 0x2a800000 0x00 0x40000>,
+ <0x00 0x2aa00000 0x00 0x40000>;
reg-names = "gcfg", "rchanrt", "tchanrt";
+ msi-parent = <&main_udmass_inta>;
#dma-cells = <1>;
ti,sci = <&dmsc>;
};
};
- wkup_gpio0: gpio@42110000 {
- compatible = "ti,j721e-gpio", "ti,keystone-gpio";
- reg = <0x0 0x42110000 0x0 0x100>;
- gpio-controller;
- #gpio-cells = <2>;
- ti,ngpio = <84>;
- ti,davinci-gpio-unbanked = <0>;
- power-domains = <&k3_pds 113 TI_SCI_PD_EXCLUSIVE>;
- clocks = <&k3_clks 113 0>;
- clock-names = "gpio";
- };
-
- mcu_conf: scm_conf@40f00000 {
- compatible = "syscon", "simple-mfd";
- reg = <0x0 0x40f00000 0x0 0x20000>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0x0 0x0 0x40f00000 0x20000>;
-
- phy_gmii_sel: phy@4040 {
- compatible = "ti,am654-cpsw-phy-sel";
- reg = <0x4040 0x4>;
- reg-names = "gmii-sel";
- #phy-cells = <1>;
- };
- };
-
mcu_cpsw: ethernet@46000000 {
compatible = "ti,j721e-cpsw-nuss";
#address-cells = <2>;
#size-cells = <2>;
- reg = <0x0 0x46000000 0x0 0x200000>;
+ reg = <0x00 0x46000000 0x00 0x200000>;
reg-names = "cpsw_nuss";
- ranges;
+ ranges = <0x00 0x00 0x00 0x46000000 0x00 0x200000>;
dma-coherent;
clocks = <&k3_clks 18 21>;
clock-names = "fck";
cpsw_port1: port@1 {
reg = <1>;
ti,mac-only;
- ti,label = "port1";
+ label = "port1";
ti,syscon-efuse = <&mcu_conf 0x200>;
phys = <&phy_gmii_sel 1>;
};
davinci_mdio: mdio@f00 {
compatible = "ti,cpsw-mdio","ti,davinci_mdio";
- reg = <0x0 0xf00 0x0 0x100>;
+ reg = <0x00 0xf00 0x00 0x100>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&k3_clks 18 21>;
bus_freq = <1000000>;
};
- cpts {
+ cpts@3d000 {
+ compatible = "ti,am65-cpts";
+ reg = <0x00 0x3d000 0x00 0x400>;
clocks = <&k3_clks 18 2>;
clock-names = "cpts";
interrupts-extended = <&gic500 GIC_SPI 858 IRQ_TYPE_LEVEL_HIGH>;
};
};
+ mcu_i2c0: i2c@40b00000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x00 0x40b00000 0x00 0x100>;
+ interrupts = <GIC_SPI 852 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 194 1>;
+ power-domains = <&k3_pds 194 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ mcu_i2c1: i2c@40b10000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x00 0x40b10000 0x00 0x100>;
+ interrupts = <GIC_SPI 853 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 195 1>;
+ power-domains = <&k3_pds 195 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ wkup_i2c0: i2c@42120000 {
+ compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+ reg = <0x00 0x42120000 0x00 0x100>;
+ interrupts = <GIC_SPI 896 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-names = "fck";
+ clocks = <&k3_clks 197 1>;
+ power-domains = <&k3_pds 197 TI_SCI_PD_SHARED>;
+ };
+
+ fss: syscon@47000000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x00 0x47000000 0x00 0x100>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ hbmc_mux: hbmc-mux {
+ compatible = "mmio-mux";
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x4 0x2>; /* HBMC select */
+ };
+
+ hbmc: hyperbus@47034000 {
+ compatible = "ti,am654-hbmc";
+ reg = <0x00 0x47034000 0x00 0x100>,
+ <0x05 0x00000000 0x01 0x0000000>;
+ power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 102 0>;
+ assigned-clocks = <&k3_clks 102 5>;
+ assigned-clock-rates = <333333333>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ mux-controls = <&hbmc_mux 0>;
+ };
+ };
+
+ tscadc0: tscadc@40200000 {
+ compatible = "ti,am3359-tscadc";
+ reg = <0x00 0x40200000 0x00 0x1000>;
+ interrupts = <GIC_SPI 860 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 0 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 0 1>;
+ assigned-clocks = <&k3_clks 0 3>;
+ assigned-clock-rates = <60000000>;
+ clock-names = "adc_tsc_fck";
+ dmas = <&main_udmap 0x7400>,
+ <&main_udmap 0x7401>;
+ dma-names = "fifo0", "fifo1";
+
+ adc {
+ #io-channel-cells = <1>;
+ compatible = "ti,am3359-adc";
+ };
+ };
+
mcu_r5fss0: r5fss@41000000 {
compatible = "ti,j7200-r5fss";
ti,cluster-mode = <1>;
memory@80000000 {
device_type = "memory";
/* 4G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
- <0x00000008 0x80000000 0x00000000 0x80000000>;
+ reg = <0x00 0x80000000 0x00 0x80000000>,
+ <0x08 0x80000000 0x00 0x80000000>;
};
reserved_memory: reserved-memory {
};
};
+&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+ >;
+ };
+};
+
&hbmc {
+ /* OSPI and HBMC are muxed inside FSS, Bootloader will enable
+ * appropriate node based on board detection
+ */
status = "disabled";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_hpb0_pins_default>;
- ranges = <0x0 0x0 0x5 0x0 0x4000000>, /* 64MB Flash on CS0 */
- <0x1 0x0 0x5 0x4000000 0x800000>; /* 8MB RAM on CS1 */
+ ranges = <0x00 0x00 0x05 0x00000000 0x4000000>, /* 64MB Flash on CS0 */
+ <0x01 0x00 0x05 0x04000000 0x800000>; /* 8MB RAM on CS1 */
flash@0,0 {
compatible = "cypress,hyperflash", "cfi-flash";
- reg = <0x0 0x0 0x4000000>;
+ reg = <0x00 0x00 0x4000000>;
+ };
+};
+
+&mailbox0_cluster0 {
+ interrupts = <436>;
+
+ mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
+ };
+
+ mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
+ ti,mbox-rx = <2 0 0>;
+ ti,mbox-tx = <3 0 0>;
+ };
+};
+
+&mailbox0_cluster1 {
+ interrupts = <432>;
+
+ mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
+ };
+
+ mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 {
+ ti,mbox-rx = <2 0 0>;
+ ti,mbox-tx = <3 0 0>;
+ };
+};
+
+&mailbox0_cluster2 {
+ status = "disabled";
+};
+
+&mailbox0_cluster3 {
+ status = "disabled";
+};
+
+&mailbox0_cluster4 {
+ status = "disabled";
+};
+
+&mailbox0_cluster5 {
+ status = "disabled";
+};
+
+&mailbox0_cluster6 {
+ status = "disabled";
+};
+
+&mailbox0_cluster7 {
+ status = "disabled";
+};
+
+&mailbox0_cluster8 {
+ status = "disabled";
+};
+
+&mailbox0_cluster9 {
+ status = "disabled";
+};
+
+&mailbox0_cluster10 {
+ status = "disabled";
+};
+
+&mailbox0_cluster11 {
+ status = "disabled";
+};
+
+&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
+ exp_som: gpio@21 {
+ compatible = "ti,tca6408";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "USB2.0_MUX_SEL", "CANUART_MUX1_SEL0",
+ "CANUART_MUX2_SEL0", "CANUART_MUX_SEL1",
+ "UART/LIN_MUX_SEL", "TRC_D17/AUDIO_REFCLK_SEL",
+ "GPIO_LIN_EN", "CAN_STB";
};
};
serial9 = &main_uart7;
serial10 = &main_uart8;
serial11 = &main_uart9;
- i2c0 = &wkup_i2c0;
- i2c1 = &mcu_i2c0;
- i2c2 = &mcu_i2c1;
- i2c3 = &main_i2c0;
- i2c4 = &main_i2c1;
- i2c5 = &main_i2c2;
- i2c6 = &main_i2c3;
- i2c7 = &main_i2c4;
- i2c8 = &main_i2c5;
- i2c9 = &main_i2c6;
};
+ chosen { };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
reg = <0x000>;
device_type = "cpu";
enable-method = "psci";
- i-cache-size = <0xC000>;
+ i-cache-size = <0xc000>;
i-cache-line-size = <64>;
i-cache-sets = <256>;
d-cache-size = <0x8000>;
reg = <0x001>;
device_type = "cpu";
enable-method = "psci";
- i-cache-size = <0xC000>;
+ i-cache-size = <0xc000>;
i-cache-line-size = <64>;
i-cache-sets = <256>;
d-cache-size = <0x8000>;
#size-cells = <2>;
ranges = <0x00 0x00100000 0x00 0x00100000 0x00 0x00020000>, /* ctrl mmr */
<0x00 0x00600000 0x00 0x00600000 0x00 0x00031100>, /* GPIO */
- <0x00 0x00A40000 0x00 0x00A40000 0x00 0x00000800>, /* timesync router */
+ <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* timesync router */
<0x00 0x01000000 0x00 0x01000000 0x00 0x0d000000>, /* Most peripherals */
<0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>, /* MAIN NAVSS */
<0x00 0x70000000 0x00 0x70000000 0x00 0x00800000>, /* MSMC RAM */
- <0x41 0x00000000 0x41 0x00000000 0x01 0x00000000>, /* PCIe1 DAT */
+ <0x00 0x18000000 0x00 0x18000000 0x00 0x08000000>, /* PCIe1 DAT0 */
+ <0x41 0x00000000 0x41 0x00000000 0x01 0x00000000>, /* PCIe1 DAT1 */
/* MCUSS_WKUP Range */
<0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>,
<0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>,
<0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>,
<0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>,
- <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>;
+ <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>,
+ <0x07 0x00000000 0x07 0x00000000 0x01 0x00000000>;
cbass_mcu_wakeup: bus@28380000 {
compatible = "simple-bus";
<0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>, /* CPSW */
<0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>, /* OSPI register space */
<0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>, /* FSS OSPI0/1 data region 0 */
- <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>; /* FSS OSPI0 data region 3 */
+ <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>, /* FSS OSPI0 data region 3 */
+ <0x07 0x00000000 0x07 0x00000000 0x01 0x00000000>; /* FSS OSPI1 data region 3 */
};
};
};
projects / u-boot.git / commitdiff