board/manroland/uc100/pcmcia.c: Fix GCC 4.6 build warnings

Fix:
pcmcia.c: In function 'pcmcia_voltage_set':
pcmcia.c:158:25: warning: variable 'pcmp' set but not used
[-Wunused-but-set-variable]
pcmcia.c:157:20: warning: variable 'immap' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Wolfgang Denk <wd@denx.de>

diff --git a/board/manroland/uc100/pcmcia.c b/board/manroland/uc100/pcmcia.c
index ad256783ce6a56299859036906d58fa342256204..db3821a5e43c9804e540dca19c57898ccfd8cd38 100644 (file)
--- a/board/manroland/uc100/pcmcia.c
+++ b/board/manroland/uc100/pcmcia.c
@@ -27,8 +27,8 @@ static void cfg_ports (void)
        immap = (immap_t *)CONFIG_SYS_IMMR;
 
        /*
-       * Configure Port A for MAX1602 PC-Card Power-Interface Switch
-       */
+        * Configure Port A for MAX1602 PC-Card Power-Interface Switch
+        */
        immap->im_ioport.iop_padat &= ~0x8000;  /* set port x output to low */
        immap->im_ioport.iop_padir |= 0x8000;   /* enable port x as output */
 
@@ -40,7 +40,6 @@ static void cfg_ports (void)
 int pcmcia_hardware_enable(int slot)
 {
        volatile immap_t        *immap;
-       volatile cpm8xx_t       *cp;
        volatile pcmconf8xx_t   *pcmp;
        volatile sysconf8xx_t   *sysp;
        uint reg, mask;
@@ -52,15 +51,14 @@ int pcmcia_hardware_enable(int slot)
        immap = (immap_t *)CONFIG_SYS_IMMR;
        sysp  = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf));
        pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-       cp    = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
 
        /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
        cfg_ports ();
 
        /*
-       * Configure SIUMCR to enable PCMCIA port B
-       * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
-       */
+        * Configure SIUMCR to enable PCMCIA port B
+        * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+        */
        sysp->sc_siumcr &= ~SIUMCR_DBGC11;      /* set DBGC to 00 */
 
        /* clear interrupt state, and disable interrupts */
@@ -68,9 +66,9 @@ int pcmcia_hardware_enable(int slot)
        pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
 
        /*
-       * Disable interrupts, DMA, and PCMCIA buffers
-       * (isolate the interface) and assert RESET signal
-       */
+        * Disable interrupts, DMA, and PCMCIA buffers
+        * (isolate the interface) and assert RESET signal
+        */
        debug ("Disable PCMCIA buffers and assert RESET\n");
        reg  = 0;
        reg |= __MY_PCMCIA_GCRX_CXRESET;        /* active high */
@@ -78,8 +76,8 @@ int pcmcia_hardware_enable(int slot)
        udelay(500);
 
        /*
-       * Make sure there is a card in the slot, then configure the interface.
-       */
+        * Make sure there is a card in the slot, then configure the interface.
+        */
        udelay(10000);
        debug ("[%d] %s: PIPR(%p)=0x%x\n",
               __LINE__,__FUNCTION__,
@@ -90,19 +88,19 @@ int pcmcia_hardware_enable(int slot)
        }
 
        /*
-       * Power On.
-       */
+        * Power On.
+        */
        mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
        reg  = pcmp->pcmc_pipr;
        debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
               reg,
               (reg&PCMCIA_VS1(slot))?"n":"ff",
               (reg&PCMCIA_VS2(slot))?"n":"ff");
-       if ((reg & mask) == mask) {
+
+       if ((reg & mask) == mask)
                puts (" 5.0V card found: ");
-       } else {
+       else
                puts (" 3.3V card found: ");
-       }
 
        /*  switch VCC on */
        immap->im_ioport.iop_padat |= 0x8000; /* power enable 3.3V */
@@ -154,8 +152,6 @@ int pcmcia_hardware_disable(int slot)
 
 int pcmcia_voltage_set(int slot, int vcc, int vpp)
 {
-       volatile immap_t        *immap;
-       volatile pcmconf8xx_t   *pcmp;
        u_long reg;
 
        debug ("voltage_set: "
@@ -163,12 +159,10 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp)
                        " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
        'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
 
-       immap = (immap_t *)CONFIG_SYS_IMMR;
-       pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
        /*
-       * Disable PCMCIA buffers (isolate the interface)
-       * and assert RESET signal
-       */
+        * Disable PCMCIA buffers (isolate the interface)
+        * and assert RESET signal
+        */
        debug ("Disable PCMCIA buffers and assert RESET\n");
        reg  = PCMCIA_PGCRX(_slot_);
        reg |= __MY_PCMCIA_GCRX_CXRESET;        /* active high */
@@ -176,10 +170,10 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp)
        udelay(500);
 
        /*
-       * Configure Port C pins for
-       * 5 Volts Enable and 3 Volts enable,
-       * Turn all power pins to Hi-Z
-       */
+        * Configure Port C pins for
+        * 5 Volts Enable and 3 Volts enable,
+        * Turn all power pins to Hi-Z
+        */
        debug ("PCMCIA power OFF\n");
        cfg_ports ();   /* Enables switch, but all in Hi-Z */