These boards are still non-generic boards.
It is a good thing that we can drop board-specific hack code
from drivers/mtd/nand/nand_base.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Andrea "llandre" Marson <andrea.marson@dave-tech.it>
config TARGET_V5FX30TEVAL
bool "Support v5fx30teval"
-config TARGET_CATCENTER
- bool "Support CATcenter"
-
-config TARGET_PPCHAMELEONEVB
- bool "Support PPChameleonEVB"
-
config TARGET_CPCI2DP
bool "Support CPCI2DP"
source "board/avnet/v5fx30teval/Kconfig"
source "board/csb272/Kconfig"
source "board/csb472/Kconfig"
-source "board/dave/PPChameleonEVB/Kconfig"
source "board/esd/cpci2dp/Kconfig"
source "board/esd/cpci405/Kconfig"
source "board/esd/plu405/Kconfig"
+++ /dev/null
-if TARGET_CATCENTER
-
-config SYS_BOARD
- default "PPChameleonEVB"
-
-config SYS_VENDOR
- default "dave"
-
-config SYS_CONFIG_NAME
- default "CATcenter"
-
-endif
-
-if TARGET_PPCHAMELEONEVB
-
-config SYS_BOARD
- default "PPChameleonEVB"
-
-config SYS_VENDOR
- default "dave"
-
-config SYS_CONFIG_NAME
- default "PPChameleonEVB"
-
-endif
+++ /dev/null
-PPCHAMELEONEVB BOARD
-#M: -
-S: Maintained
-F: board/dave/PPChameleonEVB/
-F: include/configs/CATcenter.h
-F: configs/CATcenter_defconfig
-F: configs/CATcenter_25_defconfig
-F: configs/CATcenter_33_defconfig
-
-PPCHAMELEONEVB BOARD
-M: Andrea "llandre" Marson <andrea.marson@dave-tech.it>
-S: Maintained
-F: include/configs/PPChameleonEVB.h
-F: configs/PPChameleonEVB_defconfig
-F: configs/PPChameleonEVB_BA_25_defconfig
-F: configs/PPChameleonEVB_BA_33_defconfig
-F: configs/PPChameleonEVB_HI_25_defconfig
-F: configs/PPChameleonEVB_HI_33_defconfig
-F: configs/PPChameleonEVB_ME_25_defconfig
-F: configs/PPChameleonEVB_ME_33_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = PPChameleonEVB.o flash.o nand.o
+++ /dev/null
-/*
- * (C) Copyright 2003
- * DAVE Srl
- * http://www.dave-tech.it
- * http://www.wawnet.biz
- * mailto:info@wawnet.biz
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <command.h>
-#include <malloc.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* ------------------------------------------------------------------------- */
-
-int board_early_init_f (void)
-{
- out32(GPIO0_OR, CONFIG_SYS_NAND0_CE); /* set initial outputs */
- out32(GPIO0_OR, CONFIG_SYS_NAND1_CE); /* set initial outputs */
-
- /*
- * IRQ 0-15 405GP internally generated; active high; level sensitive
- * IRQ 16 405GP internally generated; active low; level sensitive
- * IRQ 17-24 RESERVED
- * IRQ 25 (EXT IRQ 0)
- * IRQ 26 (EXT IRQ 1)
- * IRQ 27 (EXT IRQ 2)
- * IRQ 28 (EXT IRQ 3)
- * IRQ 29 (EXT IRQ 4)
- * IRQ 30 (EXT IRQ 5)
- * IRQ 31 (EXT IRQ 6)
- */
- mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
- mtdcr(UIC0ER, 0x00000000); /* disable all ints */
- mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical*/
- mtdcr(UIC0PR, 0xFFFFFF80); /* set int polarities */
- mtdcr(UIC0TR, 0x10000000); /* set int trigger levels */
- mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority*/
- mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
-
- /*
- * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
- */
-#if 1 /* test-only */
- mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
-#else
- mtebc (EBC0_CFG, 0x28400000); /* ebc in high-z */
-#endif
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-int misc_init_f (void)
-{
- return 0; /* dummy implementation */
-}
-
-extern flash_info_t flash_info[]; /* info for FLASH chips */
-
-int misc_init_r (void)
-{
- /* adjust flash start and size as well as the offset */
- gd->bd->bi_flashstart = 0 - flash_info[0].size;
- gd->bd->bi_flashoffset= flash_info[0].size - CONFIG_SYS_MONITOR_LEN;
-#if 0
- volatile unsigned short *fpga_mode =
- (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL);
- volatile unsigned char *duart0_mcr =
- (unsigned char *)((ulong)DUART0_BA + 4);
- volatile unsigned char *duart1_mcr =
- (unsigned char *)((ulong)DUART1_BA + 4);
-
- bd_t *bd = gd->bd;
- char * tmp; /* Temporary char pointer */
- unsigned char *dst;
- ulong len = sizeof(fpgadata);
- int status;
- int index;
- int i;
- unsigned long CPC0_CR0Reg;
-
- dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
- if (gunzip (dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
- printf ("GUNZIP ERROR - must RESET board to recover\n");
- do_reset (NULL, 0, 0, NULL);
- }
-
- status = fpga_boot(dst, len);
- if (status != 0) {
- printf("\nFPGA: Booting failed ");
- switch (status) {
- case ERROR_FPGA_PRG_INIT_LOW:
- printf("(Timeout: INIT not low after asserting PROGRAM*)\n ");
- break;
- case ERROR_FPGA_PRG_INIT_HIGH:
- printf("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
- break;
- case ERROR_FPGA_PRG_DONE:
- printf("(Timeout: DONE not high after programming FPGA)\n ");
- break;
- }
-
- /* display infos on fpgaimage */
- index = 15;
- for (i=0; i<4; i++) {
- len = dst[index];
- printf("FPGA: %s\n", &(dst[index+1]));
- index += len+3;
- }
- putc ('\n');
- /* delayed reboot */
- for (i=20; i>0; i--) {
- printf("Rebooting in %2d seconds \r",i);
- for (index=0;index<1000;index++)
- udelay(1000);
- }
- putc ('\n');
- do_reset(NULL, 0, 0, NULL);
- }
-
- puts("FPGA: ");
-
- /* display infos on fpgaimage */
- index = 15;
- for (i=0; i<4; i++) {
- len = dst[index];
- printf("%s ", &(dst[index+1]));
- index += len+3;
- }
- putc ('\n');
-
- free(dst);
-
- /*
- * Reset FPGA via FPGA_DATA pin
- */
- SET_FPGA(FPGA_PRG | FPGA_CLK);
- udelay(1000); /* wait 1ms */
- SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
- udelay(1000); /* wait 1ms */
-#endif
-
-#if 0
- /*
- * Enable power on PS/2 interface
- */
- *fpga_mode |= CONFIG_SYS_FPGA_CTRL_PS2_RESET;
-
- /*
- * Enable interrupts in exar duart mcr[3]
- */
- *duart0_mcr = 0x08;
- *duart1_mcr = 0x08;
-#endif
- return (0);
-}
-
-/*
- * Check Board Identity:
- */
-
-int checkboard (void)
-{
- char str[64];
- int i = getenv_f("serial#", str, sizeof(str));
-
- puts ("Board: ");
-
- if (i == -1) {
- puts ("### No HW ID - assuming PPChameleonEVB");
- } else {
- puts(str);
- }
-
- putc ('\n');
-
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-int testdram (void)
-{
- /* TODO: XXX XXX XXX */
- printf ("test: 16 MB - ok\n");
-
- return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-#ifdef CONFIG_CFB_CONSOLE
-# ifdef CONFIG_CONSOLE_EXTRA_INFO
-# include <video_fb.h>
-extern GraphicDevice smi;
-
-void video_get_info_str (int line_number, char *info)
-{
- uint pvr = get_pvr ();
-
- /* init video info strings for graphic console */
- switch (line_number) {
- case 1:
- switch (pvr) {
- case PVR_405EP_RB:
- sprintf (info, " AMCC PowerPC 405EP Rev. B");
- break;
- default:
- sprintf (info, " AMCC PowerPC 405EP Rev. <unknown>");
- break;
- }
- return;
- case 2:
- sprintf (info, " DAVE Srl PPChameleonEVB - www.dave-tech.it");
- return;
- case 3:
- sprintf (info, " %s", smi.modeIdent);
- return;
- }
-
- /* no more info lines */
- *info = 0;
- return;
-}
-# endif /* CONFIG_CONSOLE_EXTRA_INFO */
-#endif /* CONFIG_CFB_CONSOLE */
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/processor.h>
-
-/*
- * include common flash code (for esd boards)
- */
-#include "../common/flash.c"
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long * addr, flash_info_t * info);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-#ifdef __DEBUG_START_FROM_SRAM__
- return CONFIG_SYS_DUMMY_FLASH_SIZE;
-#else
- unsigned long size;
- int i;
- uint pbcr;
- unsigned long base;
- int size_val = 0;
-
- debug("[%s, %d] Entering ...\n", __FUNCTION__, __LINE__);
- debug("[%s, %d] flash_info = 0x%p ...\n", __func__, __LINE__,
- flash_info);
-
- /* Init: no FLASHes known */
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- /* Static FLASH Bank configuration here - FIXME XXX */
-
- debug("[%s, %d] Calling flash_get_size ...\n", __FUNCTION__, __LINE__);
- size = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
- size, size<<20);
- }
-
- debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
-
- /* Setup offsets */
- flash_get_offsets (-size, &flash_info[0]);
- debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
-
- /* Re-do sizing to get full correct info */
- mtdcr(EBC0_CFGADDR, PB0CR);
- pbcr = mfdcr(EBC0_CFGDATA);
- mtdcr(EBC0_CFGADDR, PB0CR);
- base = -size;
- switch (size) {
- case 1 << 20:
- size_val = 0;
- break;
- case 2 << 20:
- size_val = 1;
- break;
- case 4 << 20:
- size_val = 2;
- break;
- case 8 << 20:
- size_val = 3;
- break;
- case 16 << 20:
- size_val = 4;
- break;
- }
- pbcr = (pbcr & 0x0001ffff) | base | (size_val << 17);
- mtdcr(EBC0_CFGDATA, pbcr);
- debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
-
- /* Monitor protection ON by default */
- (void)flash_protect(FLAG_PROTECT_SET,
- -CONFIG_SYS_MONITOR_LEN,
- 0xffffffff,
- &flash_info[0]);
-
- debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
- flash_info[0].size = size;
-
- return (size);
-#endif
-}
+++ /dev/null
-/*
- * (C) Copyright 2006 DENX Software Engineering
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <nand.h>
-
-/*
- * hardware specific access to control-lines
- * function borrowed from Linux 2.6 (drivers/mtd/nand/ppchameleonevb.c)
- */
-static void ppchameleonevb_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
- ulong base = (ulong) this->IO_ADDR_W;
-
- if (ctrl & NAND_CTRL_CHANGE) {
- if ( ctrl & NAND_CLE )
- MACRO_NAND_CTL_SETCLE((unsigned long)base);
- else
- MACRO_NAND_CTL_CLRCLE((unsigned long)base);
- if ( ctrl & NAND_ALE )
- MACRO_NAND_CTL_CLRCLE((unsigned long)base);
- else
- MACRO_NAND_CTL_CLRALE((unsigned long)base);
- if ( ctrl & NAND_NCE )
- MACRO_NAND_ENABLE_CE((unsigned long)base);
- else
- MACRO_NAND_DISABLE_CE((unsigned long)base);
- }
-
- if (cmd != NAND_CMD_NONE)
- writeb(cmd, this->IO_ADDR_W);
-}
-
-
-/*
- * read device ready pin
- * function +/- borrowed from Linux 2.6 (drivers/mtd/nand/ppchameleonevb.c)
- */
-static int ppchameleonevb_device_ready(struct mtd_info *mtdinfo)
-{
- struct nand_chip *this = mtdinfo->priv;
- ulong rb_gpio_pin;
-
- /* use the base addr to find out which chip are we dealing with */
- switch((ulong) this->IO_ADDR_W) {
- case CONFIG_SYS_NAND0_BASE:
- rb_gpio_pin = CONFIG_SYS_NAND0_RDY;
- break;
- case CONFIG_SYS_NAND1_BASE:
- rb_gpio_pin = CONFIG_SYS_NAND1_RDY;
- break;
- default: /* this should never happen */
- return 0;
- break;
- }
-
- if (in32(GPIO0_IR) & rb_gpio_pin)
- return 1;
- return 0;
-}
-
-
-/*
- * Board-specific NAND initialization. The following members of the
- * argument are board-specific (per include/linux/mtd/nand.h):
- * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device
- * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device
- * - cmd_ctrl: hardwarespecific function for accesing control-lines
- * - dev_ready: hardwarespecific function for accesing device ready/busy line
- * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must
- * only be provided if a hardware ECC is available
- * - ecc.mode: mode of ecc, see defines
- * - chip_delay: chip dependent delay for transfering data from array to
- * read regs (tR)
- * - options: various chip options. They can partly be set to inform
- * nand_scan about special functionality. See the defines for further
- * explanation
- * Members with a "?" were not set in the merged testing-NAND branch,
- * so they are not set here either.
- */
-int board_nand_init(struct nand_chip *nand)
-{
-
- nand->cmd_ctrl = ppchameleonevb_hwcontrol;
- nand->dev_ready = ppchameleonevb_device_ready;
- nand->ecc.mode = NAND_ECC_SOFT;
- nand->chip_delay = NAND_BIG_DELAY_US;
- nand->options = NAND_SAMSUNG_LP_OPTIONS;
- return 0;
-}
-#endif
+++ /dev/null
-/*
- * Copyright 2007-2009 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include "config.h"
-
-#ifndef RESET_VECTOR_ADDRESS
-#define RESET_VECTOR_ADDRESS 0xfffffffc
-#endif
-
-OUTPUT_ARCH(powerpc)
-
-PHDRS
-{
- text PT_LOAD;
- bss PT_LOAD;
-}
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- *(.text*)
- } :text
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- } :text
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
- __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CONFIG_SYS_MONITOR_BASE, CONFIG_SYS_MONITOR_LEN and CONFIG_SYS_TEXT_BASE may need to be modified.");
- . = 0xFFFF8000;
- .ppcenv :
- {
- common/env_embedded.o(.ppcenv);
- }
-
- .resetvec RESET_VECTOR_ADDRESS :
- {
- KEEP(*(.resetvec))
- } :text = 0xffff
-
- . = RESET_VECTOR_ADDRESS + 0x4;
-
- /*
- * Make sure that the bss segment isn't linked at 0x0, otherwise its
- * address won't be updated during relocation fixups. Note that
- * this is a temporary fix. Code to dynamically the fixup the bss
- * location will be added in the future. When the bss relocation
- * fixup code is present this workaround should be removed.
- */
-#if (RESET_VECTOR_ADDRESS == 0xfffffffc)
- . |= 0x10;
-#endif
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- } :bss
-
- . = ALIGN(4);
- __bss_end = . ;
- PROVIDE (end = .);
-}
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=1,PPCHAMELEON_CLK_25"
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_CATCENTER=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=1,PPCHAMELEON_CLK_33"
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_CATCENTER=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=1"
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_CATCENTER=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=0,PPCHAMELEON_CLK_25"
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_PPCHAMELEONEVB=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=0,PPCHAMELEON_CLK_33"
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_PPCHAMELEONEVB=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=2,PPCHAMELEON_CLK_25"
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_PPCHAMELEONEVB=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=2,PPCHAMELEON_CLK_33"
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_PPCHAMELEONEVB=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=1,PPCHAMELEON_CLK_25"
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_PPCHAMELEONEVB=y
+++ /dev/null
-CONFIG_SYS_EXTRA_OPTIONS="PPCHAMELEON_MODULE_MODEL=1,PPCHAMELEON_CLK_33"
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_PPCHAMELEONEVB=y
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_PPCHAMELEONEVB=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+CATcenter powerpc ppc4xx - -
+PPChameleonEVB powerpc ppc4xx - - Andrea "llandre" Marson <andrea.marson@dave-tech.it>
P2020DS powerpc mpc85xx - -
P2020COME powerpc mpc85xx - - Ira W. Snyder <iws@ovro.caltech.edu>
P2020RDB powerpc mpc85xx - - Poonam Aggrwal <poonam.aggrwal@freescale.com>
}
}
#endif
-#ifdef PPCHAMELON_NAND_TIMER_HACK
- time_start = get_timer(0);
- while (get_timer(time_start) < 10)
- ;
-#endif /* PPCHAMELON_NAND_TIMER_HACK */
led_trigger_event(nand_led_trigger, LED_OFF);
status = (int)chip->read_byte(mtd);
+++ /dev/null
-/*
- * ueberarbeitet durch Christoph Seyfert
- *
- * (C) Copyright 2004-2005 DENX Software Engineering,
- * Wolfgang Grandegger <wg@denx.de>
- * (C) Copyright 2003
- * DAVE Srl
- *
- * http://www.dave-tech.it
- * http://www.wawnet.biz
- * mailto:info@wawnet.biz
- *
- * Credits: Stefan Roese, Wolfgang Denk
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_PPCHAMELEON_MODULE_BA 0 /* Basic Model */
-#define CONFIG_PPCHAMELEON_MODULE_ME 1 /* Medium Model */
-#define CONFIG_PPCHAMELEON_MODULE_HI 2 /* High-End Model */
-#ifndef CONFIG_PPCHAMELEON_MODULE_MODEL
-#define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA
-#endif
-
-/* Only one of the following two symbols must be defined (default is 25 MHz)
- * CONFIG_PPCHAMELEON_CLK_25
- * CONFIG_PPCHAMELEON_CLK_33
- */
-#if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33))
-#define CONFIG_PPCHAMELEON_CLK_25
-#endif
-
-#if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33))
-#error "* Two external frequencies (SysClk) are defined! *"
-#endif
-
-#undef CONFIG_PPCHAMELEON_SMI712
-
-/*
- * Debug stuff
- */
-#undef __DEBUG_START_FROM_SRAM__
-#define __DISABLE_MACHINE_EXCEPTION__
-
-#ifdef __DEBUG_START_FROM_SRAM__
-#define CONFIG_SYS_DUMMY_FLASH_SIZE 1024*1024*4
-#endif
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405EP 1 /* This is a PPC405 CPU */
-#define CONFIG_PPCHAMELEONEVB 1 /* ...on a PPChameleonEVB board */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFB0000 /* Reserve 320 kB for Monitor */
-#define CONFIG_SYS_LDSCRIPT "board/dave/PPChameleonEVB/u-boot.lds"
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-
-#ifdef CONFIG_PPCHAMELEON_CLK_25
-# define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
-#elif (defined (CONFIG_PPCHAMELEON_CLK_33))
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-#else
-# error "* External frequency (SysClk) not defined! *"
-#endif
-
-#define CONFIG_CONS_INDEX 2 /* Use UART1 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_VERSION_VARIABLE 1 /* add version variable */
-#define CONFIG_IDENT_STRING "1"
-
-#undef CONFIG_BOOTARGS
-
-/* Ethernet stuff */
-#define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */
-#define CONFIG_ETHADDR 00:50:C2:1E:AF:FE
-#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:50:C2:1E:AF:FD
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-
-#define CONFIG_PPC4xx_EMAC
-#undef CONFIG_EXT_PHY
-
-#define CONFIG_MII 1 /* MII PHY management */
-#ifndef CONFIG_EXT_PHY
-#define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */
-#define CONFIG_PHY1_ADDR 16 /* EMAC1 PHY address */
-#else
-#define CONFIG_PHY_ADDR 2 /* PHY address */
-#endif
-#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
-
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD 691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
- 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-
-/*-----------------------------------------------------------------------
- * NAND-FLASH stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_NAND0_BASE 0xFF400000
-#define CONFIG_SYS_NAND1_BASE 0xFF000000
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE }
-#define NAND_BIG_DELAY_US 25
-
-/* For CATcenter there is only NAND on the module */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define NAND_NO_RB
-
-#define CONFIG_SYS_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-#define CONFIG_SYS_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-
-#define CONFIG_SYS_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */
-#define CONFIG_SYS_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */
-#define CONFIG_SYS_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */
-#define CONFIG_SYS_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */
-
-
-#define MACRO_NAND_DISABLE_CE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_ENABLE_CE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_CLRALE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_ALE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_ALE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_SETALE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_ALE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_ALE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_CLRCLE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CLE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CLE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_SETCLE(nandptr) do { \
- switch((unsigned long)nandptr) { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CLE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CLE); \
- break; \
- } \
-} while(0)
-
-#ifdef NAND_NO_RB
-/* constant delay (see also tR in the datasheet) */
-#define NAND_WAIT_READY(nand) do { \
- udelay(12); \
-} while (0)
-#else
-/* use the R/B pin */
-/* TBD */
-#endif
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#if 0 /* No PCI on CATcenter */
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#undef CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */
-#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-
-#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
-#endif /* No PCI */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFFFC0000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
-#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
-#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-/*-----------------------------------------------------------------------
- * Environment Variable setup
- */
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#define CONFIG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */
-#define CONFIG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/
-#define CONFIG_ENV_ADDR_REDUND 0xFFFFA000
-#define CONFIG_ENV_SIZE_REDUND 0x2000
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
- /* 16 byte page write mode using*/
- /* last 4 bits of the address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x92015480
-#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (External SRAM) initialization */
-/* Since this must replace NOR Flash, we use the same settings for CS0 */
-#define CONFIG_SYS_EBC_PB1AP 0x92015480
-#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB2AP 0x92015480
-#define CONFIG_SYS_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB3AP 0x92015480
-#define CONFIG_SYS_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */
-
-#ifdef CONFIG_PPCHAMELEON_SMI712
-/*
- * Video console (graphic: SMI LynxEM)
- */
-#define CONFIG_VIDEO
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_SMI_LYNXEM
-#define CONFIG_VIDEO_LOGO
-/*#define CONFIG_VIDEO_BMP_LOGO*/
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-/* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */
-#define CONFIG_SYS_ISA_IO 0xE8000000
-/* see also drivers/video/videomodes.c */
-#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x303
-#endif
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-/* FPGA internal regs */
-#define CONFIG_SYS_FPGA_MODE 0x00
-#define CONFIG_SYS_FPGA_STATUS 0x02
-#define CONFIG_SYS_FPGA_TS 0x04
-#define CONFIG_SYS_FPGA_TS_LOW 0x06
-#define CONFIG_SYS_FPGA_TS_CAP0 0x10
-#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12
-#define CONFIG_SYS_FPGA_TS_CAP1 0x14
-#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16
-#define CONFIG_SYS_FPGA_TS_CAP2 0x18
-#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a
-#define CONFIG_SYS_FPGA_TS_CAP3 0x1c
-#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e
-
-/* FPGA Mode Reg */
-#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001
-#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100
-#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000
-
-/* FPGA Status Reg */
-#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001
-#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002
-#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004
-#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008
-#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000
-
-#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EP specific)
- *
- * GPIO0[0] - External Bus Controller BLAST output
- * GPIO0[1-9] - Instruction trace outputs -> GPIO
- * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
- * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
- * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
- * GPIO0[24-27] - UART0 control signal inputs/outputs
- * GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30] - EMAC0 input
- * GPIO0[31] - EMAC1 reject packet as output
- */
-#define CONFIG_SYS_GPIO0_OSRL 0x40000550
-#define CONFIG_SYS_GPIO0_OSRH 0x00000110
-#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
-/*#define CONFIG_SYS_GPIO0_ISR1H 0x15555445*/
-#define CONFIG_SYS_GPIO0_ISR1H 0x15555444
-#define CONFIG_SYS_GPIO0_TSRL 0x00000000
-#define CONFIG_SYS_GPIO0_TSRH 0x00000000
-#define CONFIG_SYS_GPIO0_TCR 0xF7FF8014
-
-#define CONFIG_NO_SERIAL_EEPROM
-
-/*--------------------------------------------------------------------*/
-
-#ifdef CONFIG_NO_SERIAL_EEPROM
-
-/*
-!-----------------------------------------------------------------------
-! Defines for entry options.
-! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that
-! are plugged in the board will be utilized as non-ECC DIMMs.
-!-----------------------------------------------------------------------
-*/
-#undef AUTO_MEMORY_CONFIG
-#define DIMM_READ_ADDR 0xAB
-#define DIMM_WRITE_ADDR 0xAA
-
-/* Defines for CPC0_PLLMR1 Register fields */
-#define PLL_ACTIVE 0x80000000
-#define CPC0_PLLMR1_SSCS 0x80000000
-#define PLL_RESET 0x40000000
-#define CPC0_PLLMR1_PLLR 0x40000000
- /* Feedback multiplier */
-#define PLL_FBKDIV 0x00F00000
-#define CPC0_PLLMR1_FBDV 0x00F00000
-#define PLL_FBKDIV_16 0x00000000
-#define PLL_FBKDIV_1 0x00100000
-#define PLL_FBKDIV_2 0x00200000
-#define PLL_FBKDIV_3 0x00300000
-#define PLL_FBKDIV_4 0x00400000
-#define PLL_FBKDIV_5 0x00500000
-#define PLL_FBKDIV_6 0x00600000
-#define PLL_FBKDIV_7 0x00700000
-#define PLL_FBKDIV_8 0x00800000
-#define PLL_FBKDIV_9 0x00900000
-#define PLL_FBKDIV_10 0x00A00000
-#define PLL_FBKDIV_11 0x00B00000
-#define PLL_FBKDIV_12 0x00C00000
-#define PLL_FBKDIV_13 0x00D00000
-#define PLL_FBKDIV_14 0x00E00000
-#define PLL_FBKDIV_15 0x00F00000
- /* Forward A divisor */
-#define PLL_FWDDIVA 0x00070000
-#define CPC0_PLLMR1_FWDVA 0x00070000
-#define PLL_FWDDIVA_8 0x00000000
-#define PLL_FWDDIVA_7 0x00010000
-#define PLL_FWDDIVA_6 0x00020000
-#define PLL_FWDDIVA_5 0x00030000
-#define PLL_FWDDIVA_4 0x00040000
-#define PLL_FWDDIVA_3 0x00050000
-#define PLL_FWDDIVA_2 0x00060000
-#define PLL_FWDDIVA_1 0x00070000
- /* Forward B divisor */
-#define PLL_FWDDIVB 0x00007000
-#define CPC0_PLLMR1_FWDVB 0x00007000
-#define PLL_FWDDIVB_8 0x00000000
-#define PLL_FWDDIVB_7 0x00001000
-#define PLL_FWDDIVB_6 0x00002000
-#define PLL_FWDDIVB_5 0x00003000
-#define PLL_FWDDIVB_4 0x00004000
-#define PLL_FWDDIVB_3 0x00005000
-#define PLL_FWDDIVB_2 0x00006000
-#define PLL_FWDDIVB_1 0x00007000
- /* PLL tune bits */
-#define PLL_TUNE_MASK 0x000003FF
-#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */
-#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */
-#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */
-#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */
-#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */
-#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */
-#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */
-
-/* Defines for CPC0_PLLMR0 Register fields */
- /* CPU divisor */
-#define PLL_CPUDIV 0x00300000
-#define CPC0_PLLMR0_CCDV 0x00300000
-#define PLL_CPUDIV_1 0x00000000
-#define PLL_CPUDIV_2 0x00100000
-#define PLL_CPUDIV_3 0x00200000
-#define PLL_CPUDIV_4 0x00300000
- /* PLB divisor */
-#define PLL_PLBDIV 0x00030000
-#define CPC0_PLLMR0_CBDV 0x00030000
-#define PLL_PLBDIV_1 0x00000000
-#define PLL_PLBDIV_2 0x00010000
-#define PLL_PLBDIV_3 0x00020000
-#define PLL_PLBDIV_4 0x00030000
- /* OPB divisor */
-#define PLL_OPBDIV 0x00003000
-#define CPC0_PLLMR0_OPDV 0x00003000
-#define PLL_OPBDIV_1 0x00000000
-#define PLL_OPBDIV_2 0x00001000
-#define PLL_OPBDIV_3 0x00002000
-#define PLL_OPBDIV_4 0x00003000
- /* EBC divisor */
-#define PLL_EXTBUSDIV 0x00000300
-#define CPC0_PLLMR0_EPDV 0x00000300
-#define PLL_EXTBUSDIV_2 0x00000000
-#define PLL_EXTBUSDIV_3 0x00000100
-#define PLL_EXTBUSDIV_4 0x00000200
-#define PLL_EXTBUSDIV_5 0x00000300
- /* MAL divisor */
-#define PLL_MALDIV 0x00000030
-#define CPC0_PLLMR0_MPDV 0x00000030
-#define PLL_MALDIV_1 0x00000000
-#define PLL_MALDIV_2 0x00000010
-#define PLL_MALDIV_3 0x00000020
-#define PLL_MALDIV_4 0x00000030
- /* PCI divisor */
-#define PLL_PCIDIV 0x00000003
-#define CPC0_PLLMR0_PPFD 0x00000003
-#define PLL_PCIDIV_1 0x00000000
-#define PLL_PCIDIV_2 0x00000001
-#define PLL_PCIDIV_3 0x00000002
-#define PLL_PCIDIV_4 0x00000003
-
-#ifdef CONFIG_PPCHAMELEON_CLK_25
-/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 25.0 MHz input clock to the 405EP) */
-#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_6 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_2)
-#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
-
-#elif (defined (CONFIG_PPCHAMELEON_CLK_33))
-
-/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */
-#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \
- PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \
- PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_2)
-#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
-
-#else
-#error "* External frequency (SysClk) not defined! *"
-#endif
-
-#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI)
-/* Model HI */
-#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55
-#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55
-#define CONFIG_SYS_OPB_FREQ 55555555
-/* Model ME */
-#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME)
-#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33
-#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33
-#define CONFIG_SYS_OPB_FREQ 66666666
-#else
-/* Model BA (default) */
-#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33
-#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33
-#define CONFIG_SYS_OPB_FREQ 66666666
-#endif
-
-#endif /* CONFIG_NO_SERIAL_EEPROM */
-
-#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nand"
-#define CONFIG_JFFS2_PART_SIZE 0x00200000
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support
- *
- * Note: fake mtd_id used, no linux mtd map file
- */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT "nand0=catcenter"
-#define MTDPARTS_DEFAULT "mtdparts=catcenter:2m(nand)"
-*/
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
- *
- * (C) Copyright 2003
- * DAVE Srl
- *
- * http://www.dave-tech.it
- * http://www.wawnet.biz
- * mailto:info@wawnet.biz
- *
- * Credits: Stefan Roese, Wolfgang Denk
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_PPCHAMELEON_MODULE_BA 0 /* Basic Model */
-#define CONFIG_PPCHAMELEON_MODULE_ME 1 /* Medium Model */
-#define CONFIG_PPCHAMELEON_MODULE_HI 2 /* High-End Model */
-#ifndef CONFIG_PPCHAMELEON_MODULE_MODEL
-#define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA
-#endif
-
-
-/* Only one of the following two symbols must be defined (default is 25 MHz)
- * CONFIG_PPCHAMELEON_CLK_25
- * CONFIG_PPCHAMELEON_CLK_33
- */
-#if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33))
-#define CONFIG_PPCHAMELEON_CLK_25
-#endif
-
-#if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33))
-#error "* Two external frequencies (SysClk) are defined! *"
-#endif
-
-#undef CONFIG_PPCHAMELEON_SMI712
-
-/*
- * Debug stuff
- */
-#undef __DEBUG_START_FROM_SRAM__
-#define __DISABLE_MACHINE_EXCEPTION__
-
-#ifdef __DEBUG_START_FROM_SRAM__
-#define CONFIG_SYS_DUMMY_FLASH_SIZE 1024*1024*4
-#endif
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405EP 1 /* This is a PPC405 CPU */
-#define CONFIG_PPCHAMELEONEVB 1 /* ...on a PPChameleonEVB board */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFB0000 /* Reserve 320 kB for Monitor */
-#define CONFIG_SYS_LDSCRIPT "board/dave/PPChameleonEVB/u-boot.lds"
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
-#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
-
-
-#ifdef CONFIG_PPCHAMELEON_CLK_25
-# define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
-#elif (defined (CONFIG_PPCHAMELEON_CLK_33))
-# define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-#else
-# error "* External frequency (SysClk) not defined! *"
-#endif
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#undef CONFIG_BOOTARGS
-
-/* Ethernet stuff */
-#define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */
-#define CONFIG_ETHADDR 00:50:c2:1e:af:fe
-#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:50:c2:1e:af:fd
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#undef CONFIG_EXT_PHY
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#ifndef CONFIG_EXT_PHY
-#define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */
-#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */
-#else
-#define CONFIG_PHY_ADDR 2 /* PHY address */
-#endif
-#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SNTP
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_RTC_M41T11 1 /* uses a M41T00 RTC */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_M41T11_BASE_YEAR 1900
-
-/*
- * SDRAM configuration (please see cpu/ppc/sdram.[ch])
- */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
-
-/* SDRAM timings used in datasheet */
-#define CONFIG_SYS_SDRAM_CL 2
-#define CONFIG_SYS_SDRAM_tRP 20
-#define CONFIG_SYS_SDRAM_tRC 65
-#define CONFIG_SYS_SDRAM_tRCD 20
-#undef CONFIG_SYS_SDRAM_tRFC
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CONFIG_SYS_BASE_BAUD 691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
- 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-
-/*-----------------------------------------------------------------------
- * NAND-FLASH stuff
- *-----------------------------------------------------------------------
- */
-
-/*
- * nand device 1 on dave (PPChameleonEVB) needs more time,
- * so we just introduce additional wait in nand_wait(),
- * effectively for both devices.
- */
-#define PPCHAMELON_NAND_TIMER_HACK
-
-#define CONFIG_SYS_NAND0_BASE 0xFF400000
-#define CONFIG_SYS_NAND1_BASE 0xFF000000
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE, CONFIG_SYS_NAND1_BASE }
-#define NAND_BIG_DELAY_US 25
-#define CONFIG_SYS_MAX_NAND_DEVICE 2 /* Max number of NAND devices */
-
-#define CONFIG_SYS_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */
-#define CONFIG_SYS_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
-#define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
-#define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
-
-#define CONFIG_SYS_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */
-#define CONFIG_SYS_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */
-#define CONFIG_SYS_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */
-#define CONFIG_SYS_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */
-
-#define MACRO_NAND_DISABLE_CE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_ENABLE_CE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_CLRALE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_ALE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_ALE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_SETALE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_ALE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_ALE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_CLRCLE(nandptr) do \
-{ \
- switch((unsigned long)nandptr) \
- { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CLE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CLE); \
- break; \
- } \
-} while(0)
-
-#define MACRO_NAND_CTL_SETCLE(nandptr) do { \
- switch((unsigned long)nandptr) { \
- case CONFIG_SYS_NAND0_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CLE); \
- break; \
- case CONFIG_SYS_NAND1_BASE: \
- out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CLE); \
- break; \
- } \
-} while(0)
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#undef CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */
-#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-
-#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-/* Reserve 256 kB for Monitor */
-/*
-#define CONFIG_SYS_FLASH_BASE 0xFFFC0000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
-*/
-
-/* Reserve 320 kB for Monitor */
-#define CONFIG_SYS_FLASH_BASE 0xFFFB0000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (320 * 1024)
-
-#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
-#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
-#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
-/*
- * The following defines are added for buggy IOP480 byte interface.
- * All other boards should use the standard values (CPCI405 etc.)
- */
-#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
-#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
-#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-/*-----------------------------------------------------------------------
- * Environment Variable setup
- */
-#ifdef ENVIRONMENT_IN_EEPROM
-
-#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */
-#define CONFIG_ENV_SIZE 0x700 /* 2048-256 bytes may be used for env vars (total size of a CAT24WC16 is 2048 bytes)*/
-
-#else /* DEFAULT: environment in flash, using redundand flash sectors */
-
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#define CONFIG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */
-#define CONFIG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/
-#define CONFIG_ENV_ADDR_REDUND 0xFFFFA000
-#define CONFIG_ENV_SIZE_REDUND 0x2000
-
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-#endif /* ENVIRONMENT_IN_EEPROM */
-
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
- /* 16 byte page write mode using*/
- /* last 4 bits of the address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
-
-/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
- */
-
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB0AP 0x92015480
-#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 1 (External SRAM) initialization */
-/* Since this must replace NOR Flash, we use the same settings for CS0 */
-#define CONFIG_SYS_EBC_PB1AP 0x92015480
-#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB2AP 0x92015480
-#define CONFIG_SYS_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */
-
-/* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB3AP 0x92015480
-#define CONFIG_SYS_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */
-
-#ifdef CONFIG_PPCHAMELEON_SMI712
-/*
- * Video console (graphic: SMI LynxEM)
- */
-#define CONFIG_VIDEO
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_SMI_LYNXEM
-#define CONFIG_VIDEO_LOGO
-/*#define CONFIG_VIDEO_BMP_LOGO*/
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-/* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */
-#define CONFIG_SYS_ISA_IO 0xE8000000
-/* see also drivers/video/videomodes.c */
-#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x303
-#endif
-
-/*-----------------------------------------------------------------------
- * FPGA stuff
- */
-/* FPGA internal regs */
-#define CONFIG_SYS_FPGA_MODE 0x00
-#define CONFIG_SYS_FPGA_STATUS 0x02
-#define CONFIG_SYS_FPGA_TS 0x04
-#define CONFIG_SYS_FPGA_TS_LOW 0x06
-#define CONFIG_SYS_FPGA_TS_CAP0 0x10
-#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12
-#define CONFIG_SYS_FPGA_TS_CAP1 0x14
-#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16
-#define CONFIG_SYS_FPGA_TS_CAP2 0x18
-#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a
-#define CONFIG_SYS_FPGA_TS_CAP3 0x1c
-#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e
-
-/* FPGA Mode Reg */
-#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001
-#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100
-#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000
-#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000
-
-/* FPGA Status Reg */
-#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001
-#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002
-#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004
-#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008
-#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000
-
-#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
-#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
-#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
-#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
-#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EP specific)
- *
- * GPIO0[0] - External Bus Controller BLAST output
- * GPIO0[1-9] - Instruction trace outputs -> GPIO
- * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
- * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
- * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
- * GPIO0[24-27] - UART0 control signal inputs/outputs
- * GPIO0[28-29] - UART1 data signal input/output
- * GPIO0[30] - EMAC0 input
- * GPIO0[31] - EMAC1 reject packet as output
- */
-#define CONFIG_SYS_GPIO0_OSRL 0x40000550
-#define CONFIG_SYS_GPIO0_OSRH 0x00000110
-#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
-/*#define CONFIG_SYS_GPIO0_ISR1H 0x15555445*/
-#define CONFIG_SYS_GPIO0_ISR1H 0x15555444
-#define CONFIG_SYS_GPIO0_TSRL 0x00000000
-#define CONFIG_SYS_GPIO0_TSRH 0x00000000
-#define CONFIG_SYS_GPIO0_TCR 0xF7FF8014
-
-#define CONFIG_NO_SERIAL_EEPROM
-
-/*--------------------------------------------------------------------*/
-
-#ifdef CONFIG_NO_SERIAL_EEPROM
-
-/*
-!-----------------------------------------------------------------------
-! Defines for entry options.
-! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that
-! are plugged in the board will be utilized as non-ECC DIMMs.
-!-----------------------------------------------------------------------
-*/
-#undef AUTO_MEMORY_CONFIG
-#define DIMM_READ_ADDR 0xAB
-#define DIMM_WRITE_ADDR 0xAA
-
-/* Defines for CPC0_PLLMR1 Register fields */
-#define PLL_ACTIVE 0x80000000
-#define CPC0_PLLMR1_SSCS 0x80000000
-#define PLL_RESET 0x40000000
-#define CPC0_PLLMR1_PLLR 0x40000000
- /* Feedback multiplier */
-#define PLL_FBKDIV 0x00F00000
-#define CPC0_PLLMR1_FBDV 0x00F00000
-#define PLL_FBKDIV_16 0x00000000
-#define PLL_FBKDIV_1 0x00100000
-#define PLL_FBKDIV_2 0x00200000
-#define PLL_FBKDIV_3 0x00300000
-#define PLL_FBKDIV_4 0x00400000
-#define PLL_FBKDIV_5 0x00500000
-#define PLL_FBKDIV_6 0x00600000
-#define PLL_FBKDIV_7 0x00700000
-#define PLL_FBKDIV_8 0x00800000
-#define PLL_FBKDIV_9 0x00900000
-#define PLL_FBKDIV_10 0x00A00000
-#define PLL_FBKDIV_11 0x00B00000
-#define PLL_FBKDIV_12 0x00C00000
-#define PLL_FBKDIV_13 0x00D00000
-#define PLL_FBKDIV_14 0x00E00000
-#define PLL_FBKDIV_15 0x00F00000
- /* Forward A divisor */
-#define PLL_FWDDIVA 0x00070000
-#define CPC0_PLLMR1_FWDVA 0x00070000
-#define PLL_FWDDIVA_8 0x00000000
-#define PLL_FWDDIVA_7 0x00010000
-#define PLL_FWDDIVA_6 0x00020000
-#define PLL_FWDDIVA_5 0x00030000
-#define PLL_FWDDIVA_4 0x00040000
-#define PLL_FWDDIVA_3 0x00050000
-#define PLL_FWDDIVA_2 0x00060000
-#define PLL_FWDDIVA_1 0x00070000
- /* Forward B divisor */
-#define PLL_FWDDIVB 0x00007000
-#define CPC0_PLLMR1_FWDVB 0x00007000
-#define PLL_FWDDIVB_8 0x00000000
-#define PLL_FWDDIVB_7 0x00001000
-#define PLL_FWDDIVB_6 0x00002000
-#define PLL_FWDDIVB_5 0x00003000
-#define PLL_FWDDIVB_4 0x00004000
-#define PLL_FWDDIVB_3 0x00005000
-#define PLL_FWDDIVB_2 0x00006000
-#define PLL_FWDDIVB_1 0x00007000
- /* PLL tune bits */
-#define PLL_TUNE_MASK 0x000003FF
-#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */
-#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */
-#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */
-#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */
-#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */
-#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */
-#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */
-
-/* Defines for CPC0_PLLMR0 Register fields */
- /* CPU divisor */
-#define PLL_CPUDIV 0x00300000
-#define CPC0_PLLMR0_CCDV 0x00300000
-#define PLL_CPUDIV_1 0x00000000
-#define PLL_CPUDIV_2 0x00100000
-#define PLL_CPUDIV_3 0x00200000
-#define PLL_CPUDIV_4 0x00300000
- /* PLB divisor */
-#define PLL_PLBDIV 0x00030000
-#define CPC0_PLLMR0_CBDV 0x00030000
-#define PLL_PLBDIV_1 0x00000000
-#define PLL_PLBDIV_2 0x00010000
-#define PLL_PLBDIV_3 0x00020000
-#define PLL_PLBDIV_4 0x00030000
- /* OPB divisor */
-#define PLL_OPBDIV 0x00003000
-#define CPC0_PLLMR0_OPDV 0x00003000
-#define PLL_OPBDIV_1 0x00000000
-#define PLL_OPBDIV_2 0x00001000
-#define PLL_OPBDIV_3 0x00002000
-#define PLL_OPBDIV_4 0x00003000
- /* EBC divisor */
-#define PLL_EXTBUSDIV 0x00000300
-#define CPC0_PLLMR0_EPDV 0x00000300
-#define PLL_EXTBUSDIV_2 0x00000000
-#define PLL_EXTBUSDIV_3 0x00000100
-#define PLL_EXTBUSDIV_4 0x00000200
-#define PLL_EXTBUSDIV_5 0x00000300
- /* MAL divisor */
-#define PLL_MALDIV 0x00000030
-#define CPC0_PLLMR0_MPDV 0x00000030
-#define PLL_MALDIV_1 0x00000000
-#define PLL_MALDIV_2 0x00000010
-#define PLL_MALDIV_3 0x00000020
-#define PLL_MALDIV_4 0x00000030
- /* PCI divisor */
-#define PLL_PCIDIV 0x00000003
-#define CPC0_PLLMR0_PPFD 0x00000003
-#define PLL_PCIDIV_1 0x00000000
-#define PLL_PCIDIV_2 0x00000001
-#define PLL_PCIDIV_3 0x00000002
-#define PLL_PCIDIV_4 0x00000003
-
-#ifdef CONFIG_PPCHAMELEON_CLK_25
-/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 25.0 MHz input clock to the 405EP) */
-#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_6 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_2)
-#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
-
-#elif (defined (CONFIG_PPCHAMELEON_CLK_33))
-
-/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */
-#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \
- PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \
- PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \
- PLL_MALDIV_1 | PLL_PCIDIV_4)
-#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW)
-
-#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \
- PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \
- PLL_MALDIV_1 | PLL_PCIDIV_2)
-#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \
- PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \
- PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI)
-
-#else
-#error "* External frequency (SysClk) not defined! *"
-#endif
-
-#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI)
-/* Model HI */
-#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55
-#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55
-#define CONFIG_SYS_OPB_FREQ 55555555
-/* Model ME */
-#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME)
-#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33
-#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33
-#define CONFIG_SYS_OPB_FREQ 66666666
-#else
-/* Model BA (default) */
-#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33
-#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33
-#define CONFIG_SYS_OPB_FREQ 66666666
-#endif
-
-#endif /* CONFIG_NO_SERIAL_EEPROM */
-
-#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */
-
-/*
- * JFFS2 partitions
- */
-
-/* No command line, one static partition */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nand0"
-#define CONFIG_JFFS2_PART_SIZE 0x00400000
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT "nor0=PPChameleon-0,nand0=ppchameleonevb-nand"
-*/
-
-/* 256 kB U-boot image */
-/*
-#define MTDPARTS_DEFAULT "mtdparts=PPChameleon-0:1m(kernel1),1m(kernel2)," \
- "1792k(user),256k(u-boot);" \
- "ppchameleonevb-nand:-(nand)"
-*/
-
-/* 320 kB U-boot image */
-/*
-#define MTDPARTS_DEFAULT "mtdparts=PPChameleon-0:1m(kernel1),1m(kernel2)," \
- "1728k(user),320k(u-boot);" \
- "ppchameleonevb-nand:-(nand)"
-*/
-
-#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff