--- /dev/null
+/*
+ * Board file for the VInCo platform
+ * Based on the the SAMA5-EK board file
+ * Configuration settings for the VInCo platform.
+ * Copyright (C) 2014 Atmel
+ * Bo Shen <voice.shen@atmel.com>
+ * Copyright (C) 2015 Free Electrons
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/at91_pmc.h>
+#include <asm/arch/at91_rstc.h>
+#include <asm/arch/atmel_mpddrc.h>
+#include <asm/arch/atmel_usba_udc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/sama5d3_smc.h>
+#include <asm/arch/sama5d4.h>
+#include <atmel_hlcdc.h>
+#include <atmel_mci.h>
+#include <lcd.h>
+#include <mmc.h>
+#include <net.h>
+#include <netdev.h>
+#include <nand.h>
+#include <spi.h>
+#include <version.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_ATMEL_SPI
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+ return bus == 0 && cs == 0;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+ at91_set_pio_output(AT91_PIO_PORTC, 3, 0);
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+ at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
+}
+
+static void vinco_spi0_hw_init(void)
+{
+ at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* SPI0_MISO */
+ at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* SPI0_MOSI */
+ at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* SPI0_SPCK */
+
+ at91_set_pio_output(AT91_PIO_PORTC, 3, 1); /* SPI0_CS0 */
+
+ /* Enable clock */
+ at91_periph_clk_enable(ATMEL_ID_SPI0);
+}
+#endif /* CONFIG_ATMEL_SPI */
+
+
+#ifdef CONFIG_CMD_USB
+static void vinco_usb_hw_init(void)
+{
+ at91_set_pio_output(AT91_PIO_PORTE, 11, 0);
+ at91_set_pio_output(AT91_PIO_PORTE, 12, 0);
+ at91_set_pio_output(AT91_PIO_PORTE, 10, 0);
+}
+#endif
+
+
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+void vinco_mci0_hw_init(void)
+{
+ at91_set_b_periph(AT91_PIO_PORTC, 5, 1); /* MCI0 CDA */
+ at91_set_b_periph(AT91_PIO_PORTC, 6, 1); /* MCI0 DA0 */
+ at91_set_b_periph(AT91_PIO_PORTC, 7, 1); /* MCI0 DA1 */
+ at91_set_b_periph(AT91_PIO_PORTC, 8, 1); /* MCI0 DA2 */
+ at91_set_b_periph(AT91_PIO_PORTC, 9, 1); /* MCI0 DA3 */
+ at91_set_b_periph(AT91_PIO_PORTC, 10, 1); /* MCI0 DA4 */
+ at91_set_b_periph(AT91_PIO_PORTC, 11, 1); /* MCI0 DA5 */
+ at91_set_b_periph(AT91_PIO_PORTC, 12, 1); /* MCI0 DA6 */
+ at91_set_b_periph(AT91_PIO_PORTC, 13, 1); /* MCI0 DA7 */
+ at91_set_b_periph(AT91_PIO_PORTC, 4, 0); /* MCI0 CLK */
+
+ /*
+ * As the mci io internal pull down is too strong, so if the io needs
+ * external pull up, the pull up resistor will be very small, if so
+ * the power consumption will increase, so disable the interanl pull
+ * down to save the power.
+ */
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 4, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 5, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 6, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 7, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 8, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 9, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 10, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 11, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 12, 0);
+ at91_set_pio_pulldown(AT91_PIO_PORTC, 13, 0);
+
+ /* Enable clock */
+ at91_periph_clk_enable(ATMEL_ID_MCI0);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ /* Enable power for MCI0 interface */
+ at91_set_pio_output(AT91_PIO_PORTE, 7, 1);
+
+ return atmel_mci_init((void *)ATMEL_BASE_MCI0);
+}
+#endif /* CONFIG_GENERIC_ATMEL_MCI */
+
+#ifdef CONFIG_MACB
+void vinco_macb0_hw_init(void)
+{
+ at91_set_a_periph(AT91_PIO_PORTB, 0, 0); /* ETXCK_EREFCK */
+ at91_set_a_periph(AT91_PIO_PORTB, 6, 0); /* ERXDV */
+ at91_set_a_periph(AT91_PIO_PORTB, 8, 0); /* ERX0 */
+ at91_set_a_periph(AT91_PIO_PORTB, 9, 0); /* ERX1 */
+ at91_set_a_periph(AT91_PIO_PORTB, 7, 0); /* ERXER */
+ at91_set_a_periph(AT91_PIO_PORTB, 2, 0); /* ETXEN */
+ at91_set_a_periph(AT91_PIO_PORTB, 12, 0); /* ETX0 */
+ at91_set_a_periph(AT91_PIO_PORTB, 13, 0); /* ETX1 */
+ at91_set_a_periph(AT91_PIO_PORTB, 17, 0); /* EMDIO */
+ at91_set_a_periph(AT91_PIO_PORTB, 16, 0); /* EMDC */
+
+ /* Enable clock */
+ at91_periph_clk_enable(ATMEL_ID_GMAC0);
+
+ /* Enable Phy*/
+ at91_set_pio_output(AT91_PIO_PORTE, 8, 1);
+}
+#endif
+
+static void vinco_serial3_hw_init(void)
+{
+ at91_set_b_periph(AT91_PIO_PORTE, 17, 1); /* TXD3 */
+ at91_set_b_periph(AT91_PIO_PORTE, 16, 0); /* RXD3 */
+
+ /* Enable clock */
+ at91_periph_clk_enable(ATMEL_ID_USART3);
+}
+
+int board_early_init_f(void)
+{
+ at91_periph_clk_enable(ATMEL_ID_PIOA);
+ at91_periph_clk_enable(ATMEL_ID_PIOB);
+ at91_periph_clk_enable(ATMEL_ID_PIOC);
+ at91_periph_clk_enable(ATMEL_ID_PIOD);
+ at91_periph_clk_enable(ATMEL_ID_PIOE);
+
+ vinco_serial3_hw_init();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_ATMEL_SPI
+ vinco_spi0_hw_init();
+#endif
+
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+ vinco_mci0_hw_init();
+#endif
+#ifdef CONFIG_MACB
+ vinco_macb0_hw_init();
+#endif
+#ifdef CONFIG_CMD_USB
+ vinco_usb_hw_init();
+#endif
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+ at91_udp_hw_init();
+#endif
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+
+#ifdef CONFIG_MACB
+ rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
+#endif
+
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+ usba_udc_probe(&pdata);
+#ifdef CONFIG_USB_ETH_RNDIS
+ usb_eth_initialize(bis);
+#endif
+#endif
+
+ return rc;
+}
--- /dev/null
+/*
+ * Configuration settings for the VInCo platform.
+ *
+ * Based on the settings for the SAMA5-EK board
+ * Copyright (C) 2014 Atmel
+ * Bo Shen <voice.shen@atmel.com>
+ * Copyright (C) 2015 Free Electrons
+ * Gregory CLEMENT gregory.clement@free-electrons.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* No NOR flash, this definition should be put before common header */
+#define CONFIG_SYS_NO_FLASH
+
+#include "at91-sama5_common.h"
+
+/* The value in the common file is too far away for the VInCo platform */
+#ifdef CONFIG_SYS_TEXT_BASE
+#undef CONFIG_SYS_TEXT_BASE
+#endif
+#define CONFIG_SYS_TEXT_BASE 0x20f00000
+
+/* serial console */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE ATMEL_BASE_USART3
+#define CONFIG_USART_ID ATMEL_ID_USART3
+
+/* SDRAM */
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
+#define CONFIG_SYS_SDRAM_SIZE 0x4000000
+
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+
+#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
+
+/* SerialFlash */
+#define CONFIG_CMD_SF
+
+#ifdef CONFIG_CMD_SF
+#define CONFIG_ATMEL_SPI
+#define CONFIG_ATMEL_SPI0
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SF_DEFAULT_BUS 0
+#define CONFIG_SF_DEFAULT_CS 0
+#define CONFIG_SF_DEFAULT_SPEED 50000000
+#define CONFIG_ENV_SPI_MAX_HZ 50000000
+#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
+#define CONFIG_ENV_SPI_MODE (SPI_MODE_0)
+#endif
+
+
+/* MMC */
+#define CONFIG_CMD_MMC
+
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_SUPPORT_EMMC_BOOT
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_GENERIC_ATMEL_MCI
+#define ATMEL_BASE_MMCI ATMEL_BASE_MCI1
+#define CONFIG_SYS_MMC_CLK_OD 500000
+
+/* For generating MMC partitions */
+#define CONFIG_PARTITION_UUIDS
+#define CONFIG_RANDOM_UUID
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_GPT
+
+#endif
+
+/* USB */
+#define CONFIG_CMD_USB
+
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_ATMEL
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
+#define CONFIG_USB_STORAGE
+#endif
+
+/* USB device */
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_ATMEL_USBA
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETH_RNDIS
+#define CONFIG_USBNET_MANUFACTURER "L+G VInCo"
+
+#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Ethernet Hardware */
+#define CONFIG_CMD_MII
+#define CONFIG_PHY_SMSC
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_RETRY_COUNT 20
+#define CONFIG_MACB_SEARCH_PHY
+
+
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_USB_ETHER_RNDIS
+
+
+#ifdef CONFIG_SYS_USE_SERIALFLASH
+/* bootstrap + u-boot + env + linux in serial flash */
+#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
+/* Use our own mapping for the VInCo platform */
+#undef CONFIG_ENV_OFFSET
+#undef CONFIG_ENV_SIZE
+
+#define CONFIG_ENV_OFFSET 0x10000
+#define CONFIG_ENV_SIZE 0x10000
+
+/* Update the bootcommand according to our mapping for the VInCo platform */
+#undef CONFIG_BOOTCOMMAND
+#define CONFIG_BOOTCOMMAND "mmc dev 0 0;" \
+ "mmc read ${loadaddr} ${k_offset} ${k_blksize};" \
+ "mmc read ${oftaddr} ${dtb_offset} ${dtb_blksize};" \
+ "bootz ${loadaddr} - ${oftaddr}"
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTARGS "console=ttyS0,115200 earlyprintk rw root=/dev/mmcblk0p2 rootfstype=ext4 rootwait quiet lpj=1990656"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "kernel_start=0x20000\0" \
+ "kernel_size=0x800000\0" \
+ "mmcblksize=0x200\0" \
+ "oftaddr=0x21000000\0" \
+ "loadaddr=0x22000000\0" \
+ "update_uboot=tftp ${loadaddr} u-boot.bin;sf probe 0;" \
+ "sf erase 0x20000 0x4B000; sf write ${loadaddr} 0x20000 0x4B000\0" \
+ "create_partition=setexpr dtb_start ${kernel_start} + 0x400000;" \
+ "setexpr rootfs_start ${kernel_start} + ${kernel_size};" \
+ "setenv partitions 'name=kernel,size=${kernel_size}," \
+ "start=${kernel_start};name=rootfs,size=-';" \
+ "gpt write mmc 0 ${partitions} \0"\
+ "f2blk_size=setexpr fileblksize ${filesize} / ${mmcblksize};" \
+ "setexpr fileblksize ${fileblksize} + 1\0" \
+ "store_kernel=tftp ${loadaddr} zImage; run f2blk_size;" \
+ "setexpr k_blksize ${fileblksize};" \
+ "setexpr k_offset ${kernel_start} / ${mmcblksize};" \
+ "mmc write ${fileaddr} ${k_offset} ${fileblksize}\0" \
+ "store_dtb=tftp ${loadaddr} at91-vinco.dtb; run f2blk_size;" \
+ "setexpr dtb_blksize ${fileblksize};" \
+ "setexpr dtb_offset ${dtb_start} / ${mmcblksize};" \
+ "mmc write ${fileaddr} ${dtb_offset} ${fileblksize}\0" \
+ "store_rootfs=tftp ${loadaddr} vinco-gateway-image-vinco.ext4;" \
+ "setexpr rootfs_offset ${rootfs_start} / ${mmcblksize};" \
+ "mmc write ${fileaddr} ${rootfs_offset} ${fileblksize}\0" \
+ "bootdelay=0\0"
+
+#endif
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#endif
projects / u-boot.git / commitdiff