#include <hwconfig.h>
#include <mmc.h>
#include <part.h>
-#include <power/regulator.h>
#include <malloc.h>
#include <fsl_esdhc.h>
#include <fdt_support.h>
#include <asm/io.h>
#include <dm.h>
-#include <asm-generic/gpio.h>
-#include <dm/pinctrl.h>
#if !CONFIG_IS_ENABLED(BLK)
#include "mmc_private.h"
IRQSTATEN_CIE | IRQSTATEN_DTOE | IRQSTATEN_DCE | \
IRQSTATEN_DEBE | IRQSTATEN_BRR | IRQSTATEN_BWR | \
IRQSTATEN_DINT)
-#define MAX_TUNING_LOOP 40
#define ESDHC_DRIVER_STAGE_VALUE 0xffffffff
struct fsl_esdhc {
uint autoc12err; /* Auto CMD error status register */
uint hostcapblt; /* Host controller capabilities register */
uint wml; /* Watermark level register */
- uint mixctrl; /* For USDHC */
- char reserved1[4]; /* reserved */
+ char reserved1[8]; /* reserved */
uint fevt; /* Force event register */
uint admaes; /* ADMA error status register */
uint adsaddr; /* ADMA system address register */
- char reserved2[4];
- uint dllctrl;
- uint dllstat;
- uint clktunectrlstatus;
- char reserved3[4];
- uint strobe_dllctrl;
- uint strobe_dllstat;
- char reserved4[72];
- uint vendorspec;
- uint mmcboot;
- uint vendorspec2;
- uint tuning_ctrl; /* on i.MX6/7/8 */
- char reserved5[44];
+ char reserved2[160];
uint hostver; /* Host controller version register */
- char reserved6[4]; /* reserved */
+ char reserved3[4]; /* reserved */
uint dmaerraddr; /* DMA error address register */
- char reserved7[4]; /* reserved */
+ char reserved4[4]; /* reserved */
uint dmaerrattr; /* DMA error attribute register */
- char reserved8[4]; /* reserved */
+ char reserved5[4]; /* reserved */
uint hostcapblt2; /* Host controller capabilities register 2 */
- char reserved9[8]; /* reserved */
- uint tcr; /* Tuning control register */
- char reserved10[28]; /* reserved */
- uint sddirctl; /* SD direction control register */
- char reserved11[712];/* reserved */
- uint scr; /* eSDHC control register */
+ char reserved6[756]; /* reserved */
+ uint esdhcctl; /* eSDHC control register */
};
struct fsl_esdhc_plat {
struct mmc mmc;
};
-struct esdhc_soc_data {
- u32 flags;
- u32 caps;
-};
-
/**
* struct fsl_esdhc_priv
*
* @dev: pointer for the device
* @non_removable: 0: removable; 1: non-removable
* @wp_enable: 1: enable checking wp; 0: no check
- * @vs18_enable: 1: use 1.8V voltage; 0: use 3.3V
- * @flags: ESDHC_FLAG_xx in include/fsl_esdhc.h
- * @caps: controller capabilities
- * @tuning_step: tuning step setting in tuning_ctrl register
- * @start_tuning_tap: the start point for tuning in tuning_ctrl register
- * @strobe_dll_delay_target: settings in strobe_dllctrl
- * @signal_voltage: indicating the current voltage
* @cd_gpio: gpio for card detection
* @wp_gpio: gpio for write protection
*/
unsigned int sdhc_clk;
struct clk per_clk;
unsigned int clock;
- unsigned int mode;
unsigned int bus_width;
#if !CONFIG_IS_ENABLED(BLK)
struct mmc *mmc;
struct udevice *dev;
int non_removable;
int wp_enable;
- int vs18_enable;
- u32 flags;
- u32 caps;
- u32 tuning_step;
- u32 tuning_start_tap;
- u32 strobe_dll_delay_target;
- u32 signal_voltage;
-#if IS_ENABLED(CONFIG_DM_REGULATOR)
- struct udevice *vqmmc_dev;
- struct udevice *vmmc_dev;
-#endif
-#ifdef CONFIG_DM_GPIO
- struct gpio_desc cd_gpio;
- struct gpio_desc wp_gpio;
-#endif
};
/* Return the XFERTYP flags for a given command and data packet */
{
int timeout;
struct fsl_esdhc *regs = priv->esdhc_regs;
-#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
- defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
+#if defined(CONFIG_FSL_LAYERSCAPE)
dma_addr_t addr;
#endif
uint wml_value;
esdhc_clrsetbits32(®s->wml, WML_RD_WML_MASK, wml_value);
#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
-#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
- defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
+#if defined(CONFIG_FSL_LAYERSCAPE)
addr = virt_to_phys((void *)(data->dest));
if (upper_32_bits(addr))
printf("Error found for upper 32 bits\n");
printf("\nThe SD card is locked. Can not write to a locked card.\n\n");
return -ETIMEDOUT;
}
- } else {
-#ifdef CONFIG_DM_GPIO
- if (dm_gpio_is_valid(&priv->wp_gpio) && dm_gpio_get_value(&priv->wp_gpio)) {
- printf("\nThe SD card is locked. Can not write to a locked card.\n\n");
- return -ETIMEDOUT;
- }
-#endif
}
esdhc_clrsetbits32(®s->wml, WML_WR_WML_MASK,
wml_value << 16);
#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
-#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
- defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
+#if defined(CONFIG_FSL_LAYERSCAPE)
addr = virt_to_phys((void *)(data->src));
if (upper_32_bits(addr))
printf("Error found for upper 32 bits\n");
unsigned end = 0;
unsigned size = roundup(ARCH_DMA_MINALIGN,
data->blocks*data->blocksize);
-#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
- defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
+#if defined(CONFIG_FSL_LAYERSCAPE)
dma_addr_t addr;
addr = virt_to_phys((void *)(data->dest));
invalidate_dcache_range(start, end);
}
-#ifdef CONFIG_MCF5441x
-/*
- * Swaps 32-bit words to little-endian byte order.
- */
-static inline void sd_swap_dma_buff(struct mmc_data *data)
-{
- int i, size = data->blocksize >> 2;
- u32 *buffer = (u32 *)data->dest;
- u32 sw;
-
- while (data->blocks--) {
- for (i = 0; i < size; i++) {
- sw = __sw32(*buffer);
- *buffer++ = sw;
- }
- }
-}
-#endif
-
/*
* Sends a command out on the bus. Takes the mmc pointer,
* a command pointer, and an optional data pointer.
/* Send the command */
esdhc_write32(®s->cmdarg, cmd->cmdarg);
-#if defined(CONFIG_FSL_USDHC)
- esdhc_write32(®s->mixctrl,
- (esdhc_read32(®s->mixctrl) & 0xFFFFFF80) | (xfertyp & 0x7F)
- | (mmc->ddr_mode ? XFERTYP_DDREN : 0));
- esdhc_write32(®s->xfertyp, xfertyp & 0xFFFF0000);
-#else
esdhc_write32(®s->xfertyp, xfertyp);
-#endif
if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK) ||
(cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200))
goto out;
}
- /* Switch voltage to 1.8V if CMD11 succeeded */
- if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V) {
- esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT);
-
- printf("Run CMD11 1.8V switch\n");
- /* Sleep for 5 ms - max time for card to switch to 1.8V */
- udelay(5000);
- }
-
/* Workaround for ESDHC errata ENGcm03648 */
if (!data && (cmd->resp_type & MMC_RSP_BUSY)) {
int timeout = 6000;
*/
if (data->flags & MMC_DATA_READ) {
check_and_invalidate_dcache_range(cmd, data);
-#ifdef CONFIG_MCF5441x
- sd_swap_dma_buff(data);
-#endif
}
#endif
}
while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTD))
;
}
-
- /* If this was CMD11, then notify that power cycle is needed */
- if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V)
- printf("CMD11 to switch to 1.8V mode failed, card requires power cycle.\n");
}
esdhc_write32(®s->irqstat, -1);
{
struct fsl_esdhc *regs = priv->esdhc_regs;
int div = 1;
-#ifdef ARCH_MXC
-#ifdef CONFIG_MX53
- /* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */
- int pre_div = (regs == (struct fsl_esdhc *)MMC_SDHC3_BASE_ADDR) ? 2 : 1;
-#else
- int pre_div = 1;
-#endif
-#else
int pre_div = 2;
-#endif
int ddr_pre_div = mmc->ddr_mode ? 2 : 1;
int sdhc_clk = priv->sdhc_clk;
uint clk;
clk = (pre_div << 8) | (div << 4);
-#ifdef CONFIG_FSL_USDHC
- esdhc_clrbits32(®s->vendorspec, VENDORSPEC_CKEN);
-#else
esdhc_clrbits32(®s->sysctl, SYSCTL_CKEN);
-#endif
esdhc_clrsetbits32(®s->sysctl, SYSCTL_CLOCK_MASK, clk);
udelay(10000);
-#ifdef CONFIG_FSL_USDHC
- esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN | VENDORSPEC_CKEN);
-#else
esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_CKEN);
-#endif
priv->clock = clock;
}
}
#endif
-#ifdef MMC_SUPPORTS_TUNING
-static int esdhc_change_pinstate(struct udevice *dev)
-{
- struct fsl_esdhc_priv *priv = dev_get_priv(dev);
- int ret;
-
- switch (priv->mode) {
- case UHS_SDR50:
- case UHS_DDR50:
- ret = pinctrl_select_state(dev, "state_100mhz");
- break;
- case UHS_SDR104:
- case MMC_HS_200:
- case MMC_HS_400:
- ret = pinctrl_select_state(dev, "state_200mhz");
- break;
- default:
- ret = pinctrl_select_state(dev, "default");
- break;
- }
-
- if (ret)
- printf("%s %d error\n", __func__, priv->mode);
-
- return ret;
-}
-
-static void esdhc_reset_tuning(struct mmc *mmc)
-{
- struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
- struct fsl_esdhc *regs = priv->esdhc_regs;
-
- if (priv->flags & ESDHC_FLAG_USDHC) {
- if (priv->flags & ESDHC_FLAG_STD_TUNING) {
- esdhc_clrbits32(®s->autoc12err,
- MIX_CTRL_SMPCLK_SEL |
- MIX_CTRL_EXE_TUNE);
- }
- }
-}
-
-static void esdhc_set_strobe_dll(struct mmc *mmc)
-{
- struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
- struct fsl_esdhc *regs = priv->esdhc_regs;
- u32 val;
-
- if (priv->clock > ESDHC_STROBE_DLL_CLK_FREQ) {
- writel(ESDHC_STROBE_DLL_CTRL_RESET, ®s->strobe_dllctrl);
-
- /*
- * enable strobe dll ctrl and adjust the delay target
- * for the uSDHC loopback read clock
- */
- val = ESDHC_STROBE_DLL_CTRL_ENABLE |
- (priv->strobe_dll_delay_target <<
- ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
- writel(val, ®s->strobe_dllctrl);
- /* wait 1us to make sure strobe dll status register stable */
- mdelay(1);
- val = readl(®s->strobe_dllstat);
- if (!(val & ESDHC_STROBE_DLL_STS_REF_LOCK))
- pr_warn("HS400 strobe DLL status REF not lock!\n");
- if (!(val & ESDHC_STROBE_DLL_STS_SLV_LOCK))
- pr_warn("HS400 strobe DLL status SLV not lock!\n");
- }
-}
-
-static int esdhc_set_timing(struct mmc *mmc)
-{
- struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
- struct fsl_esdhc *regs = priv->esdhc_regs;
- u32 mixctrl;
-
- mixctrl = readl(®s->mixctrl);
- mixctrl &= ~(MIX_CTRL_DDREN | MIX_CTRL_HS400_EN);
-
- switch (mmc->selected_mode) {
- case MMC_LEGACY:
- case SD_LEGACY:
- esdhc_reset_tuning(mmc);
- writel(mixctrl, ®s->mixctrl);
- break;
- case MMC_HS_400:
- mixctrl |= MIX_CTRL_DDREN | MIX_CTRL_HS400_EN;
- writel(mixctrl, ®s->mixctrl);
- esdhc_set_strobe_dll(mmc);
- break;
- case MMC_HS:
- case MMC_HS_52:
- case MMC_HS_200:
- case SD_HS:
- case UHS_SDR12:
- case UHS_SDR25:
- case UHS_SDR50:
- case UHS_SDR104:
- writel(mixctrl, ®s->mixctrl);
- break;
- case UHS_DDR50:
- case MMC_DDR_52:
- mixctrl |= MIX_CTRL_DDREN;
- writel(mixctrl, ®s->mixctrl);
- break;
- default:
- printf("Not supported %d\n", mmc->selected_mode);
- return -EINVAL;
- }
-
- priv->mode = mmc->selected_mode;
-
- return esdhc_change_pinstate(mmc->dev);
-}
-
-static int esdhc_set_voltage(struct mmc *mmc)
-{
- struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev);
- struct fsl_esdhc *regs = priv->esdhc_regs;
- int ret;
-
- priv->signal_voltage = mmc->signal_voltage;
- switch (mmc->signal_voltage) {
- case MMC_SIGNAL_VOLTAGE_330:
- if (priv->vs18_enable)
- return -EIO;
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
- if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) {
- ret = regulator_set_value(priv->vqmmc_dev, 3300000);
- if (ret) {
- printf("Setting to 3.3V error");
- return -EIO;
- }
- /* Wait for 5ms */
- mdelay(5);
- }
-#endif
-
- esdhc_clrbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT);
- if (!(esdhc_read32(®s->vendorspec) &
- ESDHC_VENDORSPEC_VSELECT))
- return 0;
-
- return -EAGAIN;
- case MMC_SIGNAL_VOLTAGE_180:
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
- if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) {
- ret = regulator_set_value(priv->vqmmc_dev, 1800000);
- if (ret) {
- printf("Setting to 1.8V error");
- return -EIO;
- }
- }
-#endif
- esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT);
- if (esdhc_read32(®s->vendorspec) & ESDHC_VENDORSPEC_VSELECT)
- return 0;
-
- return -EAGAIN;
- case MMC_SIGNAL_VOLTAGE_120:
- return -ENOTSUPP;
- default:
- return 0;
- }
-}
-
-static void esdhc_stop_tuning(struct mmc *mmc)
-{
- struct mmc_cmd cmd;
-
- cmd.cmdidx = MMC_CMD_STOP_TRANSMISSION;
- cmd.cmdarg = 0;
- cmd.resp_type = MMC_RSP_R1b;
-
- dm_mmc_send_cmd(mmc->dev, &cmd, NULL);
-}
-
-static int fsl_esdhc_execute_tuning(struct udevice *dev, uint32_t opcode)
-{
- struct fsl_esdhc_plat *plat = dev_get_platdata(dev);
- struct fsl_esdhc_priv *priv = dev_get_priv(dev);
- struct fsl_esdhc *regs = priv->esdhc_regs;
- struct mmc *mmc = &plat->mmc;
- u32 irqstaten = readl(®s->irqstaten);
- u32 irqsigen = readl(®s->irqsigen);
- int i, ret = -ETIMEDOUT;
- u32 val, mixctrl;
-
- /* clock tuning is not needed for upto 52MHz */
- if (mmc->clock <= 52000000)
- return 0;
-
- /* This is readw/writew SDHCI_HOST_CONTROL2 when tuning */
- if (priv->flags & ESDHC_FLAG_STD_TUNING) {
- val = readl(®s->autoc12err);
- mixctrl = readl(®s->mixctrl);
- val &= ~MIX_CTRL_SMPCLK_SEL;
- mixctrl &= ~(MIX_CTRL_FBCLK_SEL | MIX_CTRL_AUTO_TUNE_EN);
-
- val |= MIX_CTRL_EXE_TUNE;
- mixctrl |= MIX_CTRL_FBCLK_SEL | MIX_CTRL_AUTO_TUNE_EN;
-
- writel(val, ®s->autoc12err);
- writel(mixctrl, ®s->mixctrl);
- }
-
- /* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE); */
- mixctrl = readl(®s->mixctrl);
- mixctrl = MIX_CTRL_DTDSEL_READ | (mixctrl & ~MIX_CTRL_SDHCI_MASK);
- writel(mixctrl, ®s->mixctrl);
-
- writel(IRQSTATEN_BRR, ®s->irqstaten);
- writel(IRQSTATEN_BRR, ®s->irqsigen);
-
- /*
- * Issue opcode repeatedly till Execute Tuning is set to 0 or the number
- * of loops reaches 40 times.
- */
- for (i = 0; i < MAX_TUNING_LOOP; i++) {
- u32 ctrl;
-
- if (opcode == MMC_CMD_SEND_TUNING_BLOCK_HS200) {
- if (mmc->bus_width == 8)
- writel(0x7080, ®s->blkattr);
- else if (mmc->bus_width == 4)
- writel(0x7040, ®s->blkattr);
- } else {
- writel(0x7040, ®s->blkattr);
- }
-
- /* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE) */
- val = readl(®s->mixctrl);
- val = MIX_CTRL_DTDSEL_READ | (val & ~MIX_CTRL_SDHCI_MASK);
- writel(val, ®s->mixctrl);
-
- /* We are using STD tuning, no need to check return value */
- mmc_send_tuning(mmc, opcode, NULL);
-
- ctrl = readl(®s->autoc12err);
- if ((!(ctrl & MIX_CTRL_EXE_TUNE)) &&
- (ctrl & MIX_CTRL_SMPCLK_SEL)) {
- /*
- * need to wait some time, make sure sd/mmc fininsh
- * send out tuning data, otherwise, the sd/mmc can't
- * response to any command when the card still out
- * put the tuning data.
- */
- mdelay(1);
- ret = 0;
- break;
- }
-
- /* Add 1ms delay for SD and eMMC */
- mdelay(1);
- }
-
- writel(irqstaten, ®s->irqstaten);
- writel(irqsigen, ®s->irqsigen);
-
- esdhc_stop_tuning(mmc);
-
- return ret;
-}
-#endif
-
static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
{
struct fsl_esdhc *regs = priv->esdhc_regs;
- int ret __maybe_unused;
#ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
/* Select to use peripheral clock */
esdhc_clock_control(priv, false);
- esdhc_setbits32(®s->scr, ESDHCCTL_PCS);
+ esdhc_setbits32(®s->esdhcctl, ESDHCCTL_PCS);
esdhc_clock_control(priv, true);
#endif
/* Set the clock speed */
if (priv->clock != mmc->clock)
set_sysctl(priv, mmc, mmc->clock);
-#ifdef MMC_SUPPORTS_TUNING
- if (mmc->clk_disable) {
-#ifdef CONFIG_FSL_USDHC
- esdhc_clrbits32(®s->vendorspec, VENDORSPEC_CKEN);
-#else
- esdhc_clrbits32(®s->sysctl, SYSCTL_CKEN);
-#endif
- } else {
-#ifdef CONFIG_FSL_USDHC
- esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN |
- VENDORSPEC_CKEN);
-#else
- esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_CKEN);
-#endif
- }
-
- if (priv->mode != mmc->selected_mode) {
- ret = esdhc_set_timing(mmc);
- if (ret) {
- printf("esdhc_set_timing error %d\n", ret);
- return ret;
- }
- }
-
- if (priv->signal_voltage != mmc->signal_voltage) {
- ret = esdhc_set_voltage(mmc);
- if (ret) {
- printf("esdhc_set_voltage error %d\n", ret);
- return ret;
- }
- }
-#endif
-
/* Set the bus width */
esdhc_clrbits32(®s->proctl, PROCTL_DTW_4 | PROCTL_DTW_8);
return -ETIMEDOUT;
}
-#if defined(CONFIG_FSL_USDHC)
- /* RSTA doesn't reset MMC_BOOT register, so manually reset it */
- esdhc_write32(®s->mmcboot, 0x0);
- /* Reset MIX_CTRL and CLK_TUNE_CTRL_STATUS regs to 0 */
- esdhc_write32(®s->mixctrl, 0x0);
- esdhc_write32(®s->clktunectrlstatus, 0x0);
-
- /* Put VEND_SPEC to default value */
- if (priv->vs18_enable)
- esdhc_write32(®s->vendorspec, (VENDORSPEC_INIT |
- ESDHC_VENDORSPEC_VSELECT));
- else
- esdhc_write32(®s->vendorspec, VENDORSPEC_INIT);
-
- /* Disable DLL_CTRL delay line */
- esdhc_write32(®s->dllctrl, 0x0);
-#endif
-
-#ifndef ARCH_MXC
/* Enable cache snooping */
- esdhc_write32(®s->scr, 0x00000040);
-#endif
+ esdhc_write32(®s->esdhcctl, 0x00000040);
-#ifndef CONFIG_FSL_USDHC
esdhc_setbits32(®s->sysctl, SYSCTL_HCKEN | SYSCTL_IPGEN);
-#else
- esdhc_setbits32(®s->vendorspec, VENDORSPEC_HCKEN | VENDORSPEC_IPGEN);
-#endif
/* Set the initial clock speed */
mmc_set_clock(mmc, 400000, MMC_CLK_ENABLE);
/* Disable the BRR and BWR bits in IRQSTAT */
esdhc_clrbits32(®s->irqstaten, IRQSTATEN_BRR | IRQSTATEN_BWR);
-#ifdef CONFIG_MCF5441x
- esdhc_write32(®s->proctl, PROCTL_INIT | PROCTL_D3CD);
-#else
/* Put the PROCTL reg back to the default */
esdhc_write32(®s->proctl, PROCTL_INIT);
-#endif
/* Set timout to the maximum value */
esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16);
#if CONFIG_IS_ENABLED(DM_MMC)
if (priv->non_removable)
return 1;
-#ifdef CONFIG_DM_GPIO
- if (dm_gpio_is_valid(&priv->cd_gpio))
- return dm_gpio_get_value(&priv->cd_gpio);
-#endif
#endif
while (!(esdhc_read32(®s->prsstat) & PRSSTAT_CINS) && --timeout)
if (ret)
return ret;
-#ifdef CONFIG_MCF5441x
- /* ColdFire, using SDHC_DATA[3] for card detection */
- esdhc_write32(®s->proctl, PROCTL_INIT | PROCTL_D3CD);
-#endif
-
-#ifndef CONFIG_FSL_USDHC
- esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
- | SYSCTL_IPGEN | SYSCTL_CKEN);
- /* Clearing tuning bits in case ROM has set it already */
- esdhc_write32(®s->mixctrl, 0);
- esdhc_write32(®s->autoc12err, 0);
- esdhc_write32(®s->clktunectrlstatus, 0);
-#else
- esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN |
- VENDORSPEC_HCKEN | VENDORSPEC_IPGEN | VENDORSPEC_CKEN);
-#endif
-
- if (priv->vs18_enable)
- esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT);
+ esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN |
+ SYSCTL_IPGEN | SYSCTL_CKEN);
writel(SDHCI_IRQ_EN_BITS, ®s->irqstaten);
cfg = &plat->cfg;
voltage_caps = 0;
caps = esdhc_read32(®s->hostcapblt);
-#ifdef CONFIG_MCF5441x
- /*
- * MCF5441x RM declares in more points that sdhc clock speed must
- * never exceed 25 Mhz. From this, the HS bit needs to be disabled
- * from host capabilities.
- */
- caps &= ~ESDHC_HOSTCAPBLT_HSS;
-#endif
-
#ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC135
caps = caps & ~(ESDHC_HOSTCAPBLT_SRS |
ESDHC_HOSTCAPBLT_VS18 | ESDHC_HOSTCAPBLT_VS30);
cfg->host_caps &= ~MMC_MODE_8BIT;
#endif
- cfg->host_caps |= priv->caps;
-
cfg->f_min = 400000;
cfg->f_max = min(priv->sdhc_clk, (u32)200000000);
cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
- writel(0, ®s->dllctrl);
- if (priv->flags & ESDHC_FLAG_USDHC) {
- if (priv->flags & ESDHC_FLAG_STD_TUNING) {
- u32 val = readl(®s->tuning_ctrl);
-
- val |= ESDHC_STD_TUNING_EN;
- val &= ~ESDHC_TUNING_START_TAP_MASK;
- val |= priv->tuning_start_tap;
- val &= ~ESDHC_TUNING_STEP_MASK;
- val |= (priv->tuning_step) << ESDHC_TUNING_STEP_SHIFT;
- writel(val, ®s->tuning_ctrl);
- }
- }
-
return 0;
}
priv->bus_width = cfg->max_bus_width;
priv->sdhc_clk = cfg->sdhc_clk;
priv->wp_enable = cfg->wp_enable;
- priv->vs18_enable = cfg->vs18_enable;
return 0;
};
#ifndef CONFIG_PPC
#include <asm/arch/clock.h>
#endif
-__weak void init_clk_usdhc(u32 index)
-{
-}
-
static int fsl_esdhc_probe(struct udevice *dev)
{
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
struct fsl_esdhc_plat *plat = dev_get_platdata(dev);
struct fsl_esdhc_priv *priv = dev_get_priv(dev);
- const void *fdt = gd->fdt_blob;
- int node = dev_of_offset(dev);
- struct esdhc_soc_data *data =
- (struct esdhc_soc_data *)dev_get_driver_data(dev);
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
- struct udevice *vqmmc_dev;
-#endif
fdt_addr_t addr;
unsigned int val;
struct mmc *mmc;
priv->esdhc_regs = (struct fsl_esdhc *)addr;
#endif
priv->dev = dev;
- priv->mode = -1;
- if (data) {
- priv->flags = data->flags;
- priv->caps = data->caps;
- }
val = dev_read_u32_default(dev, "bus-width", -1);
if (val == 8)
else
priv->bus_width = 1;
- val = fdtdec_get_int(fdt, node, "fsl,tuning-step", 1);
- priv->tuning_step = val;
- val = fdtdec_get_int(fdt, node, "fsl,tuning-start-tap",
- ESDHC_TUNING_START_TAP_DEFAULT);
- priv->tuning_start_tap = val;
- val = fdtdec_get_int(fdt, node, "fsl,strobe-dll-delay-target",
- ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT);
- priv->strobe_dll_delay_target = val;
-
if (dev_read_bool(dev, "non-removable")) {
priv->non_removable = 1;
} else {
priv->non_removable = 0;
-#ifdef CONFIG_DM_GPIO
- gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
- GPIOD_IS_IN);
-#endif
}
- if (dev_read_prop(dev, "fsl,wp-controller", NULL)) {
- priv->wp_enable = 1;
- } else {
- priv->wp_enable = 0;
-#ifdef CONFIG_DM_GPIO
- gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio,
- GPIOD_IS_IN);
-#endif
- }
-
- priv->vs18_enable = 0;
-
-#if CONFIG_IS_ENABLED(DM_REGULATOR)
- /*
- * If emmc I/O has a fixed voltage at 1.8V, this must be provided,
- * otherwise, emmc will work abnormally.
- */
- ret = device_get_supply_regulator(dev, "vqmmc-supply", &vqmmc_dev);
- if (ret) {
- dev_dbg(dev, "no vqmmc-supply\n");
- } else {
- ret = regulator_set_enable(vqmmc_dev, true);
- if (ret) {
- dev_err(dev, "fail to enable vqmmc-supply\n");
- return ret;
- }
-
- if (regulator_get_value(vqmmc_dev) == 1800000)
- priv->vs18_enable = 1;
- }
-#endif
-
- if (fdt_get_property(fdt, node, "no-1-8-v", NULL))
- priv->caps &= ~(UHS_CAPS | MMC_MODE_HS200 | MMC_MODE_HS400);
-
- /*
- * TODO:
- * Because lack of clk driver, if SDHC clk is not enabled,
- * need to enable it first before this driver is invoked.
- *
- * we use MXC_ESDHC_CLK to get clk freq.
- * If one would like to make this function work,
- * the aliases should be provided in dts as this:
- *
- * aliases {
- * mmc0 = &usdhc1;
- * mmc1 = &usdhc2;
- * mmc2 = &usdhc3;
- * mmc3 = &usdhc4;
- * };
- * Then if your board only supports mmc2 and mmc3, but we can
- * correctly get the seq as 2 and 3, then let mxc_get_clock
- * work as expected.
- */
-
- init_clk_usdhc(dev->seq);
+ priv->wp_enable = 1;
if (IS_ENABLED(CONFIG_CLK)) {
/* Assigned clock already set clock */
.get_cd = fsl_esdhc_get_cd,
.send_cmd = fsl_esdhc_send_cmd,
.set_ios = fsl_esdhc_set_ios,
-#ifdef MMC_SUPPORTS_TUNING
- .execute_tuning = fsl_esdhc_execute_tuning,
-#endif
};
#endif
-static struct esdhc_soc_data usdhc_imx7d_data = {
- .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
- | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
- | ESDHC_FLAG_HS400,
- .caps = UHS_CAPS | MMC_MODE_HS200 | MMC_MODE_DDR_52MHz |
- MMC_MODE_HS_52MHz | MMC_MODE_HS,
-};
-
static const struct udevice_id fsl_esdhc_ids[] = {
- { .compatible = "fsl,imx53-esdhc", },
- { .compatible = "fsl,imx6ul-usdhc", },
- { .compatible = "fsl,imx6sx-usdhc", },
- { .compatible = "fsl,imx6sl-usdhc", },
- { .compatible = "fsl,imx6q-usdhc", },
- { .compatible = "fsl,imx7d-usdhc", .data = (ulong)&usdhc_imx7d_data,},
- { .compatible = "fsl,imx7ulp-usdhc", },
{ .compatible = "fsl,esdhc", },
{ /* sentinel */ }
};
projects / u-boot.git / commitdiff