Changes since U-Boot 1.1.1:
======================================================================
+* Enable NAND flash support for NC650 board.
+
+* Patch by Thomas Lange 07 Oct 2004:
+ Updated README for DBAu1x00 boards to match current status
+
* Patch by Philippe Robin, 28 Sept 2004:
Fix Flash support for Versatile.
-By Thomas.Lange@corelatus.se 2003-10-06
+By Thomas.Lange@corelatus.se 2004-Oct-05
----------------------------------------
-DbAu1000 is a development board from AMD containing
-an Alchemy AU1000 with mips32 core.
+DbAu1xx0 are development boards from AMD containing
+an Alchemy AU1xx0 series cpu with mips32 core.
+Existing cpu:s are Au1000, Au1100, Au1500 and Au1550
Limitations & comments
----------------------
-I assume that you set board to BIG endian!
-Little endian not tested, most probably broken.
+Support was originally big endian only.
+I have not tested, but several u-boot users report working
+configurations in little endian mode.
I named the board dbau1x00, to allow
support for all three development boards
-some day ( dbau1000, dbau1100 and dbau1500 ).
+( dbau1000, dbau1100 and dbau1500 ).
+Now there is a new board called dbau1550 also, which
+should be supported RSN.
-I only have a dbau1000, so all testing is limited
-to this board!
+I only have a dbau1000, so my testing is limited
+to this board.
The board has two different flash banks, that can
be selected via dip switch. This makes it possible
to test new bootloaders without thrashing the YAMON
-boot loader deliviered with board.
+boot loader delivered with board.
+
+NOTE! When you switch between the two boot flashes, the
+base addresses will be swapped.
+Have this in mind when you compile u-boot. TEXT_BASE has
+to match the address where u-boot is located when you
+actually launch.
Ethernet only supported for mac0.
-Pcmcia only supported for slot 0, only 3.3V.
+PCMCIA only supported for slot 0, only 3.3V.
-Pcmcia IDE tested with Sandisk Compact Flash and
+PCMCIA IDE tested with Sandisk Compact Flash and
IBM microdrive.
###################################
###################################
If you partition a disk on another system (e.g. laptop),
all bytes will be swapped on 16bit level when using
-PCMCIA!!!!
+PCMCIA and running cpu in big endian mode!!!!
This is probably due to an error in Au1000 chip.
return (get_ram_size(base, maxsize));
}
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+void nand_init(void)
+{
+ unsigned long totlen = nand_probe(CFG_NAND_BASE);
+
+ printf ("%4lu MB\n", totlen >> 20);
+}
+#endif
+
/*
* Software (bit-bang) I2C driver configuration
*/
-#define SCL 0x10000000 /* PA 3 */
-#define SDA 0x40000000 /* PA 1 */
+#define SCL 0x1000 /* PA 3 */
+#define SDA 0x2000 /* PA 2 */
#define PAR immr->im_ioport.iop_papar
#define DIR immr->im_ioport.iop_padir
else DAT &= ~SDA
#define I2C_SCL(bit) if (bit) DAT |= SCL; \
else DAT &= ~SCL
-#define I2C_DELAY udelay(50) /* 1/4 I2C clock duration */
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-#define CFG_I2C_EEPROM_ADDR 0x50
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* 16 bytes page write mode */
-
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+#define CONFIG_RTC_PCF8563
+#define CFG_I2C_RTC_ADDR 0x51
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_ASKENV | \
CFG_CMD_DHCP | \
- CFG_CMD_EEPROM | \
CFG_CMD_I2C | \
+ CFG_CMD_NAND | \
CFG_CMD_DATE )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
+/*
+ * NAND flash support
+ */
+#define CFG_MAX_NAND_DEVICE 1
+#define NAND_ChipID_UNKNOWN 0x00
+#define SECTORSIZE 512
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+#define ADDR_COLUMN 1
+#define NAND_NO_RB
+
+#define NAND_WAIT_READY(nand) udelay(12)
+#define WRITE_NAND_COMMAND(d, adr) WRITE_NAND(d, adr + 2)
+#define WRITE_NAND_ADDRESS(d, adr) WRITE_NAND(d, adr + 1)
+#define WRITE_NAND(d, adr) (*(volatile uint8_t *)(adr) = (uint8_t)(d))
+#define READ_NAND(adr) (*(volatile uint8_t *)(adr))
+#define NAND_DISABLE_CE(nand) /* nop */
+#define NAND_ENABLE_CE(nand) /* nop */
+#define NAND_CTL_CLRALE(nandptr) /* nop */
+#define NAND_CTL_SETALE(nandptr) /* nop */
+#define NAND_CTL_CLRCLE(nandptr) /* nop */
+#define NAND_CTL_SETCLE(nandptr) /* nop */
+
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V)
+/*
+ * BR2 and OR2 (NAND Flash)
+ */
+#define CFG_NAND_BASE 0x50000000
+#define CFG_NAND_SIZE 0x04000000
+
+#define CFG_OR_TIMING_NAND (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
+ OR_SCY_15_CLK | OR_EHTR | OR_TRLX)
+
+#define CFG_BR2_PRELIM ((CFG_NAND_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
+#define CFG_OR2_PRELIM (((-CFG_NAND_SIZE) & OR_AM_MSK) | CFG_OR_TIMING_NAND)
+
/*
* BR3 and OR3 (SDRAM)
*/
projects / u-boot.git / commitdiff