beagle: enable DVI_PUP

this patch addresses the issue that there is no DVI output on beagleboard-xm in
u-boot; the TFP410 is not powered on, DVI_PUP needs to be set high

this is done differently on beagleboard-xm rev. B/C versus earlier boards:
beagleboard-xm B/C need to set GPIO2 of the TWL4030
earlier boards need to set GPIO170

note that the change occured somewhere inbetween beagleboard-xm rev. A2 and A3

note that beagleboard-xm rev. A and rev. B cannot be distinguished using
get_board_revision(), REVISION_XM_A/REVISION_XM_B is bogus

due to this glitch, the patch cannot work correctly on some beagleboard-xm
rev A/B boards

tested on beagleboard-xm rev. C (you should see orange color on a monitor)

note that the framebuffer is NOT yet set up, this could be done along the
lines below (for 800x480 resolution and RGB24) before calling omap3_dss_enable()

static void configure_frame_buffer() {
	writel(0x80500000, (uint *) 0x48050480); // address
	writel(0x80500000, (uint *) 0x48050484);
	writel(0x01df031f, (uint *) 0x4805048c); // size
	writel(0x00000091, (uint *) 0x480504a0); // RGB24
}

Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>

diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c
index 87578763bb737eaf656370fd3dfa18a7eace9146..c09c833980179d502c5182bce17b8f99d80c5bfe 100644 (file)
--- a/board/ti/beagle/beagle.c
+++ b/board/ti/beagle/beagle.c
@@ -251,6 +251,38 @@ void beagle_display_init(void)
        }
 }
 
+/*
+ * Enable DVI power
+ */
+static void beagle_dvi_pup() {
+       uchar val;
+
+       switch (get_board_revision()) {
+       case REVISION_AXBX:
+       case REVISION_CX:
+       case REVISION_C4:
+       case REVISION_XM_A:
+               gpio_request(170, "");
+               gpio_direction_output(170, 0);
+               gpio_set_value(170, 1);
+               break;
+       case REVISION_XM_B:
+       case REVISION_XM_C:
+       default:
+               #define GPIODATADIR1 (TWL4030_BASEADD_GPIO+3)
+               #define GPIODATAOUT1 (TWL4030_BASEADD_GPIO+6)
+
+               i2c_read(TWL4030_CHIP_GPIO, GPIODATADIR1, 1, &val, 1);
+               val |= 4;
+               i2c_write(TWL4030_CHIP_GPIO, GPIODATADIR1, 1, &val, 1);
+
+               i2c_read(TWL4030_CHIP_GPIO, GPIODATAOUT1, 1, &val, 1);
+               val |= 4;
+               i2c_write(TWL4030_CHIP_GPIO, GPIODATAOUT1, 1, &val, 1);
+               break;
+       }
+}
+
 /*
  * Routine: misc_init_r
  * Description: Configure board specific parts
@@ -422,6 +454,8 @@ int misc_init_r(void)
                GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
 
        dieid_num_r();
+
+       beagle_dvi_pup();
        beagle_display_init();
        omap3_dss_enable();