Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.
As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
config TARGET_AT91SAM9M10G45EK
bool "Atmel AT91SAM9M10G45-EK board"
select CPU_ARM926EJS
+ select SUPPORT_SPL
config TARGET_PM9G45
bool "Ronetix pm9g45 board"
--- /dev/null
+/*
+ * Copyright (C) 2015 Atmel Corporation
+ * Bo Shen <voice.shen@atmel.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE, \
+ LENGTH = CONFIG_SPL_MAX_SIZE }
+MEMORY { .sdram : ORIGIN = CONFIG_SPL_BSS_START_ADDR, \
+ LENGTH = CONFIG_SPL_BSS_MAX_SIZE }
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ .text :
+ {
+ __start = .;
+ *(.vectors)
+ arch/arm/cpu/arm926ejs/start.o (.text*)
+ *(.text*)
+ } >.sram
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram
+
+ . = ALIGN(4);
+ .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
+
+ . = ALIGN(4);
+ __image_copy_end = .;
+
+ .end :
+ {
+ *(.__end)
+ } >.sram
+
+ .bss :
+ {
+ . = ALIGN(4);
+ __bss_start = .;
+ *(.bss*)
+ . = ALIGN(4);
+ __bss_end = .;
+ } >.sdram
+}
{
}
-void spl_board_init(void)
+void __weak spl_board_init(void)
+{
+}
+
+void board_init_f(ulong dummy)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
#include <common.h>
#include <asm/io.h>
+#include <asm/arch/clk.h>
#include <asm/arch/at91sam9g45_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <lcd.h>
+#include <linux/mtd/nand.h>
#include <atmel_lcdc.h>
#include <atmel_mci.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
}
#endif
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
+
+void at91_spl_board_init(void)
+{
+ /*
+ * On the at91sam9m10g45ek board, the chip wm9711 stays in the
+ * test mode, so it needs do some action to exit test mode.
+ */
+ at91_periph_clk_enable(ATMEL_ID_PIODE);
+ at91_set_gpio_output(AT91_PIN_PD7, 0);
+ at91_set_gpio_output(AT91_PIN_PD8, 0);
+ at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1);
+ at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1);
+
+#ifdef CONFIG_SYS_USE_MMC
+ at91_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+ at91sam9m10g45ek_nand_hw_init();
+#endif
+}
+
+#include <asm/arch/atmel_mpddrc.h>
+static void ddr2_conf(struct atmel_mpddr *ddr2)
+{
+ ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+ ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+ ATMEL_MPDDRC_CR_NR_ROW_14 |
+ ATMEL_MPDDRC_CR_DQMS_SHARED |
+ ATMEL_MPDDRC_CR_CAS_DDR_CAS3);
+
+ ddr2->rtr = 0x24b;
+
+ ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */
+ 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */
+ 1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/
+ 1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */
+ 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */
+
+ ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */
+ 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+ 16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+ 14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+ ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+ 0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+ 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
+}
+
+void mem_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+ struct atmel_mpddr ddr2;
+ unsigned long csa;
+
+ ddr2_conf(&ddr2);
+
+ /* enable DDR2 clock */
+ writel(0x4, &pmc->scer);
+
+ /* Chip select 1 is for DDR2/SDRAM */
+ csa = readl(&mat->ebicsa);
+ csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
+ csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V;
+ writel(csa, &mat->ebicsa);
+
+ /* DDRAM2 Controller initialize */
+ ddr2_init(ATMEL_BASE_CS6, &ddr2);
+}
+#endif
+
#ifdef CONFIG_CMD_USB
static void at91sam9m10g45ek_usb_hw_init(void)
{
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_MMC"
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_NANDFLASH"
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
*/
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x300000
+#define CONFIG_SPL_MAX_SIZE 0x010000
+#define CONFIG_SPL_STACK 0x310000
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+
+#define CONFIG_SYS_MONITOR_LEN 0x80000
+
+#ifdef CONFIG_SYS_USE_MMC
+
+#define CONFIG_SPL_BSS_START_ADDR 0x70000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000
+#define CONFIG_SYS_SPL_MALLOC_START 0x70080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
+
+#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+
+#elif CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_SOFTECC
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \
+ 48, 49, 50, 51, 52, 53, 54, 55, \
+ 56, 57, 58, 59, 60, 61, 62, 63, }
+#endif
+
+#define CONFIG_SPL_ATMEL_SIZE
+#define CONFIG_SYS_MASTER_CLOCK 132096000
+#define CONFIG_SYS_AT91_PLLA 0x20c73f03
+#define CONFIG_SYS_MCKR 0x1301
+#define CONFIG_SYS_MCKR_CSS 0x1302
+
+#define ATMEL_BASE_MPDDRC ATMEL_BASE_DDRSDRC0
#endif
projects / u-boot.git / commitdiff