net: rtl8139: Introduce device private data

Introduce rtl8139_pdata, which is a super-structure around eth_device
and tracks per-device state, here the device IO address, PCI BDF, RX
and TX ring position. Pass this structure around instead of the old
non-DM eth_device in preparation for DM conversion.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>

diff --git a/drivers/net/rtl8139.c b/drivers/net/rtl8139.c
index aa1374054245c3a83356fdc29b1395d8a7d052c7..dff77de06e54efd6551bc3fe90540ff472048ab6 100644 (file)
--- a/drivers/net/rtl8139.c
+++ b/drivers/net/rtl8139.c
@@ -191,7 +191,14 @@
 #define RTL_STS_RXBADALIGN                     BIT(1)
 #define RTL_STS_RXSTATUSOK                     BIT(0)
 
-static unsigned int cur_rx, cur_tx;
+struct rtl8139_priv {
+       struct eth_device       dev;
+       unsigned int            cur_rx;
+       unsigned int            cur_tx;
+       unsigned long           ioaddr;
+       pci_dev_t               devno;
+       unsigned char           enetaddr[6];
+};
 
 /* The RTL8139 can only transmit from a contiguous, aligned memory block.  */
 static unsigned char tx_buffer[TX_BUF_SIZE] __aligned(4);
@@ -222,43 +229,43 @@ static void rtl8139_eeprom_delay(uintptr_t regbase)
        inl(regbase + RTL_REG_CFG9346);
 }
 
-static int rtl8139_read_eeprom(struct eth_device *dev,
+static int rtl8139_read_eeprom(struct rtl8139_priv *priv,
                               unsigned int location, unsigned int addr_len)
 {
        unsigned int read_cmd = location | (EE_READ_CMD << addr_len);
-       uintptr_t ee_addr = dev->iobase + RTL_REG_CFG9346;
+       uintptr_t ee_addr = priv->ioaddr + RTL_REG_CFG9346;
        unsigned int retval = 0;
        u8 dataval;
        int i;
 
        outb(EE_ENB & ~EE_CS, ee_addr);
        outb(EE_ENB, ee_addr);
-       rtl8139_eeprom_delay(dev->iobase);
+       rtl8139_eeprom_delay(priv->ioaddr);
 
        /* Shift the read command bits out. */
        for (i = 4 + addr_len; i >= 0; i--) {
                dataval = (read_cmd & BIT(i)) ? EE_DATA_WRITE : 0;
                outb(EE_ENB | dataval, ee_addr);
-               rtl8139_eeprom_delay(dev->iobase);
+               rtl8139_eeprom_delay(priv->ioaddr);
                outb(EE_ENB | dataval | EE_SHIFT_CLK, ee_addr);
-               rtl8139_eeprom_delay(dev->iobase);
+               rtl8139_eeprom_delay(priv->ioaddr);
        }
 
        outb(EE_ENB, ee_addr);
-       rtl8139_eeprom_delay(dev->iobase);
+       rtl8139_eeprom_delay(priv->ioaddr);
 
        for (i = 16; i > 0; i--) {
                outb(EE_ENB | EE_SHIFT_CLK, ee_addr);
-               rtl8139_eeprom_delay(dev->iobase);
+               rtl8139_eeprom_delay(priv->ioaddr);
                retval <<= 1;
                retval |= inb(ee_addr) & EE_DATA_READ;
                outb(EE_ENB, ee_addr);
-               rtl8139_eeprom_delay(dev->iobase);
+               rtl8139_eeprom_delay(priv->ioaddr);
        }
 
        /* Terminate the EEPROM access. */
        outb(~EE_CS, ee_addr);
-       rtl8139_eeprom_delay(dev->iobase);
+       rtl8139_eeprom_delay(priv->ioaddr);
 
        return retval;
 }
@@ -268,29 +275,29 @@ static const unsigned int rtl8139_rx_config =
        (RX_FIFO_THRESH << 13) |
        (RX_DMA_BURST << 8);
 
-static void rtl8139_set_rx_mode(struct eth_device *dev)
+static void rtl8139_set_rx_mode(struct rtl8139_priv *priv)
 {
        /* !IFF_PROMISC */
        unsigned int rx_mode = RTL_REG_RXCONFIG_ACCEPTBROADCAST |
                               RTL_REG_RXCONFIG_ACCEPTMULTICAST |
                               RTL_REG_RXCONFIG_ACCEPTMYPHYS;
 
-       outl(rtl8139_rx_config | rx_mode, dev->iobase + RTL_REG_RXCONFIG);
+       outl(rtl8139_rx_config | rx_mode, priv->ioaddr + RTL_REG_RXCONFIG);
 
-       outl(0xffffffff, dev->iobase + RTL_REG_MAR0 + 0);
-       outl(0xffffffff, dev->iobase + RTL_REG_MAR0 + 4);
+       outl(0xffffffff, priv->ioaddr + RTL_REG_MAR0 + 0);
+       outl(0xffffffff, priv->ioaddr + RTL_REG_MAR0 + 4);
 }
 
-static void rtl8139_hw_reset(struct eth_device *dev)
+static void rtl8139_hw_reset(struct rtl8139_priv *priv)
 {
        u8 reg;
        int i;
 
-       outb(RTL_REG_CHIPCMD_CMDRESET, dev->iobase + RTL_REG_CHIPCMD);
+       outb(RTL_REG_CHIPCMD_CMDRESET, priv->ioaddr + RTL_REG_CHIPCMD);
 
        /* Give the chip 10ms to finish the reset. */
        for (i = 0; i < 100; i++) {
-               reg = inb(dev->iobase + RTL_REG_CHIPCMD);
+               reg = inb(priv->ioaddr + RTL_REG_CHIPCMD);
                if (!(reg & RTL_REG_CHIPCMD_CMDRESET))
                        break;
 
@@ -298,25 +305,25 @@ static void rtl8139_hw_reset(struct eth_device *dev)
        }
 }
 
-static void rtl8139_reset(struct eth_device *dev)
+static void rtl8139_reset(struct rtl8139_priv *priv)
 {
        int i;
 
-       cur_rx = 0;
-       cur_tx = 0;
+       priv->cur_rx = 0;
+       priv->cur_tx = 0;
 
-       rtl8139_hw_reset(dev);
+       rtl8139_hw_reset(priv);
 
        for (i = 0; i < ETH_ALEN; i++)
-               outb(dev->enetaddr[i], dev->iobase + RTL_REG_MAC0 + i);
+               outb(priv->enetaddr[i], priv->ioaddr + RTL_REG_MAC0 + i);
 
        /* Must enable Tx/Rx before setting transfer thresholds! */
        outb(RTL_REG_CHIPCMD_CMDRXENB | RTL_REG_CHIPCMD_CMDTXENB,
-            dev->iobase + RTL_REG_CHIPCMD);
+            priv->ioaddr + RTL_REG_CHIPCMD);
 
        /* accept no frames yet! */
-       outl(rtl8139_rx_config, dev->iobase + RTL_REG_RXCONFIG);
-       outl((TX_DMA_BURST << 8) | 0x03000000, dev->iobase + RTL_REG_TXCONFIG);
+       outl(rtl8139_rx_config, priv->ioaddr + RTL_REG_RXCONFIG);
+       outl((TX_DMA_BURST << 8) | 0x03000000, priv->ioaddr + RTL_REG_TXCONFIG);
 
        /*
         * The Linux driver changes RTL_REG_CONFIG1 here to use a different
@@ -331,7 +338,7 @@ static void rtl8139_reset(struct eth_device *dev)
        debug_cond(DEBUG_RX, "rx ring address is %p\n", rx_ring);
 
        flush_cache((unsigned long)rx_ring, RX_BUF_LEN);
-       outl(phys_to_bus(dev->priv, (int)rx_ring), dev->iobase + RTL_REG_RXBUF);
+       outl(phys_to_bus(priv->devno, (int)rx_ring), priv->ioaddr + RTL_REG_RXBUF);
 
        /*
         * If we add multicast support, the RTL_REG_MAR0 register would have
@@ -340,21 +347,22 @@ static void rtl8139_reset(struct eth_device *dev)
         * unicast.
         */
        outb(RTL_REG_CHIPCMD_CMDRXENB | RTL_REG_CHIPCMD_CMDTXENB,
-            dev->iobase + RTL_REG_CHIPCMD);
+            priv->ioaddr + RTL_REG_CHIPCMD);
 
-       outl(rtl8139_rx_config, dev->iobase + RTL_REG_RXCONFIG);
+       outl(rtl8139_rx_config, priv->ioaddr + RTL_REG_RXCONFIG);
 
        /* Start the chip's Tx and Rx process. */
-       outl(0, dev->iobase + RTL_REG_RXMISSED);
+       outl(0, priv->ioaddr + RTL_REG_RXMISSED);
 
-       rtl8139_set_rx_mode(dev);
+       rtl8139_set_rx_mode(priv);
 
        /* Disable all known interrupts by setting the interrupt mask. */
-       outw(0, dev->iobase + RTL_REG_INTRMASK);
+       outw(0, priv->ioaddr + RTL_REG_INTRMASK);
 }
 
 static int rtl8139_send(struct eth_device *dev, void *packet, int length)
 {
+       struct rtl8139_priv *priv = container_of(dev, struct rtl8139_priv, dev);
        unsigned int len = length;
        unsigned long txstatus;
        unsigned int status;
@@ -372,13 +380,13 @@ static int rtl8139_send(struct eth_device *dev, void *packet, int length)
                tx_buffer[len++] = '\0';
 
        flush_cache((unsigned long)tx_buffer, length);
-       outl(phys_to_bus(dev->priv, (unsigned long)tx_buffer),
-            dev->iobase + RTL_REG_TXADDR0 + cur_tx * 4);
+       outl(phys_to_bus(priv->devno, (unsigned long)tx_buffer),
+            priv->ioaddr + RTL_REG_TXADDR0 + priv->cur_tx * 4);
        outl(((TX_FIFO_THRESH << 11) & 0x003f0000) | len,
-            dev->iobase + RTL_REG_TXSTATUS0 + cur_tx * 4);
+            priv->ioaddr + RTL_REG_TXSTATUS0 + priv->cur_tx * 4);
 
        do {
-               status = inw(dev->iobase + RTL_REG_INTRSTATUS);
+               status = inw(priv->ioaddr + RTL_REG_INTRSTATUS);
                /*
                 * Only acknlowledge interrupt sources we can properly
                 * handle here - the RTL_REG_INTRSTATUS_RXOVERFLOW/
@@ -387,26 +395,26 @@ static int rtl8139_send(struct eth_device *dev, void *packet, int length)
                 */
                status &= RTL_REG_INTRSTATUS_TXOK | RTL_REG_INTRSTATUS_TXERR |
                          RTL_REG_INTRSTATUS_PCIERR;
-               outw(status, dev->iobase + RTL_REG_INTRSTATUS);
+               outw(status, priv->ioaddr + RTL_REG_INTRSTATUS);
                if (status)
                        break;
 
                udelay(10);
        } while (i++ < RTL_TIMEOUT);
 
-       txstatus = inl(dev->iobase + RTL_REG_TXSTATUS0 + cur_tx * 4);
+       txstatus = inl(priv->ioaddr + RTL_REG_TXSTATUS0 + priv->cur_tx * 4);
 
        if (!(status & RTL_REG_INTRSTATUS_TXOK)) {
                debug_cond(DEBUG_TX,
                           "tx timeout/error (%d usecs), status %hX txstatus %lX\n",
                           10 * i, status, txstatus);
 
-               rtl8139_reset(dev);
+               rtl8139_reset(priv);
 
                return 0;
        }
 
-       cur_tx = (cur_tx + 1) % NUM_TX_DESC;
+       priv->cur_tx = (priv->cur_tx + 1) % NUM_TX_DESC;
 
        debug_cond(DEBUG_TX, "tx done, status %hX txstatus %lX\n",
                   status, txstatus);
@@ -416,6 +424,7 @@ static int rtl8139_send(struct eth_device *dev, void *packet, int length)
 
 static int rtl8139_recv(struct eth_device *dev)
 {
+       struct rtl8139_priv *priv = container_of(dev, struct rtl8139_priv, dev);
        const unsigned int rxstat = RTL_REG_INTRSTATUS_RXFIFOOVER |
                                    RTL_REG_INTRSTATUS_RXOVERFLOW |
                                    RTL_REG_INTRSTATUS_RXOK;
@@ -424,16 +433,16 @@ static int rtl8139_recv(struct eth_device *dev)
        unsigned int status;
        int length = 0;
 
-       if (inb(dev->iobase + RTL_REG_CHIPCMD) & RTL_REG_CHIPCMD_RXBUFEMPTY)
+       if (inb(priv->ioaddr + RTL_REG_CHIPCMD) & RTL_REG_CHIPCMD_RXBUFEMPTY)
                return 0;
 
-       status = inw(dev->iobase + RTL_REG_INTRSTATUS);
+       status = inw(priv->ioaddr + RTL_REG_INTRSTATUS);
        /* See below for the rest of the interrupt acknowledges.  */
-       outw(status & ~rxstat, dev->iobase + RTL_REG_INTRSTATUS);
+       outw(status & ~rxstat, priv->ioaddr + RTL_REG_INTRSTATUS);
 
        debug_cond(DEBUG_RX, "%s: int %hX ", __func__, status);
 
-       ring_offs = cur_rx % RX_BUF_LEN;
+       ring_offs = priv->cur_rx % RX_BUF_LEN;
        /* ring_offs is guaranteed being 4-byte aligned */
        rx_status = le32_to_cpu(*(unsigned int *)(rx_ring + ring_offs));
        rx_size = rx_status >> 16;
@@ -446,7 +455,7 @@ static int rtl8139_recv(struct eth_device *dev)
            (rx_size > ETH_FRAME_LEN + 4)) {
                printf("rx error %hX\n", rx_status);
                /* this clears all interrupts still pending */
-               rtl8139_reset(dev);
+               rtl8139_reset(priv);
                return 0;
        }
 
@@ -469,45 +478,51 @@ static int rtl8139_recv(struct eth_device *dev)
        }
        flush_cache((unsigned long)rx_ring, RX_BUF_LEN);
 
-       cur_rx = ROUND(cur_rx + rx_size + 4, 4);
-       outw(cur_rx - 16, dev->iobase + RTL_REG_RXBUFPTR);
+       priv->cur_rx = ROUND(priv->cur_rx + rx_size + 4, 4);
+       outw(priv->cur_rx - 16, priv->ioaddr + RTL_REG_RXBUFPTR);
        /*
         * See RTL8139 Programming Guide V0.1 for the official handling of
         * Rx overflow situations. The document itself contains basically
         * no usable information, except for a few exception handling rules.
         */
-       outw(status & rxstat, dev->iobase + RTL_REG_INTRSTATUS);
+       outw(status & rxstat, priv->ioaddr + RTL_REG_INTRSTATUS);
 
        return length;
 }
 
 static int rtl8139_init(struct eth_device *dev, bd_t *bis)
 {
-       unsigned short *ap = (unsigned short *)dev->enetaddr;
+       struct rtl8139_priv *priv = container_of(dev, struct rtl8139_priv, dev);
+       unsigned short *ap = (unsigned short *)priv->enetaddr;
        int addr_len, i;
        u8 reg;
 
        /* Bring the chip out of low-power mode. */
-       outb(0x00, dev->iobase + RTL_REG_CONFIG1);
+       outb(0x00, priv->ioaddr + RTL_REG_CONFIG1);
 
-       addr_len = rtl8139_read_eeprom(dev, 0, 8) == 0x8129 ? 8 : 6;
+       addr_len = rtl8139_read_eeprom(priv, 0, 8) == 0x8129 ? 8 : 6;
        for (i = 0; i < 3; i++)
-               *ap++ = le16_to_cpu(rtl8139_read_eeprom(dev, i + 7, addr_len));
+               *ap++ = le16_to_cpu(rtl8139_read_eeprom(priv, i + 7, addr_len));
 
-       rtl8139_reset(dev);
+       rtl8139_reset(priv);
 
-       reg = inb(dev->iobase + RTL_REG_MEDIASTATUS);
+       reg = inb(priv->ioaddr + RTL_REG_MEDIASTATUS);
        if (reg & RTL_REG_MEDIASTATUS_MSRLINKFAIL) {
                printf("Cable not connected or other link failure\n");
                return -1;
        }
 
+       /* Non-DM compatibility */
+       memcpy(priv->dev.enetaddr, priv->enetaddr, 6);
+
        return 0;
 }
 
 static void rtl8139_stop(struct eth_device *dev)
 {
-       rtl8139_hw_reset(dev);
+       struct rtl8139_priv *priv = container_of(dev, struct rtl8139_priv, dev);
+
+       rtl8139_hw_reset(priv);
 }
 
 static int rtl8139_bcast_addr(struct eth_device *dev, const u8 *bcast_mac,
@@ -529,6 +544,7 @@ static struct pci_device_id supported[] = {
 
 int rtl8139_initialize(bd_t *bis)
 {
+       struct rtl8139_priv *priv;
        struct eth_device *dev;
        int card_number = 0;
        pci_dev_t devno;
@@ -546,16 +562,20 @@ int rtl8139_initialize(bd_t *bis)
 
                debug("rtl8139: REALTEK RTL8139 @0x%x\n", iobase);
 
-               dev = calloc(1, sizeof(*dev));
-               if (!dev) {
+               priv = calloc(1, sizeof(*priv));
+               if (!priv) {
                        printf("Can not allocate memory of rtl8139\n");
                        break;
                }
 
+               priv->devno = devno;
+               priv->ioaddr = (unsigned long)bus_to_phys(devno, iobase);
+
+               dev = &priv->dev;
+
                rtl8139_name(dev->name, card_number);
 
-               dev->priv = (void *)devno;
-               dev->iobase = (unsigned long)bus_to_phys(devno, iobase);
+               dev->iobase = priv->ioaddr;     /* Non-DM compatibility */
                dev->init = rtl8139_init;
                dev->halt = rtl8139_stop;
                dev->send = rtl8139_send;