The P1023RDS board is the reference board for the P1023 SoC.
Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Roy Zang <tie-fei.zang@freescale.com>
mpc7448hpc2 MPC7448
+ P1023RDS P1023
John Zhan <zhanz@sinovee.com>
--- /dev/null
+#
+# Copyright 2010-2011 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or modify it
+# under the terms of the GNU General Public License as published by the Free
+# Software Foundation; either version 2 of the License, or (at your option)
+# any later version.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS-y += $(BOARD).o
+COBJS-y += law.o
+COBJS-y += tlb.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ *
+ * Authors: Chunhe Lan <b25806@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ */
+
+#ifndef __BCSR_H_
+#define __BCSR_H_
+
+#include <common.h>
+
+/*
+ * BCSR Bit definitions
+ * BCSR 15 *
+ 0 device insertion oriention
+ 1 stack processor present
+ 2 power supply shut down/normal operation
+ 3 I2C bus0 drive enable
+ 4 reserved
+ 5:7 I2C bus0 select
+ 5 - I2C_BUS_0_SS0
+ 6 - I2C_BUS_0_SS1
+ 7 - I2C_BUS_0_SS2
+*/
+
+/* BCSR register base address is 0xFX000020 */
+#define BCSR_BASE_REG_OFFSET 0x20
+#define BCSR_ACCESS_REG_ADDR (CONFIG_SYS_BCSR_BASE + BCSR_BASE_REG_OFFSET)
+
+#define BCSR15_DEV_INS_ORI 0x80
+#define BCSR15_STACK_PRO_PRE 0x40
+#define BCSR15_POWER_SUPPLY 0x20
+#define BCSR15_I2C_BUS0_EN 0x10
+#define BCSR15_I2C_BUS0_SEG0 0x00
+#define BCSR15_I2C_BUS0_SEG1 0x04
+#define BCSR15_I2C_BUS0_SEG2 0x02
+#define BCSR15_I2C_BUS0_SEG3 0x06
+#define BCSR15_I2C_BUS0_SEG4 0x01
+#define BCSR15_I2C_BUS0_SEG5 0x05
+#define BCSR15_I2C_BUS0_SEG6 0x03
+#define BCSR15_I2C_BUS0_SEG7 0x07
+#define BCSR15_I2C_BUS0_SEG_CLR 0x07
+#define BCSR19_SGMII_SEL_L 0x01
+
+/*BCSR Utils functions*/
+void fixup_i2c_bus0_sel_seg0(void);
+#endif /* __BCSR_H_ */
--- /dev/null
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_4M,
+ LAW_TRGT_IF_DPAA_SWP_SRAM),
+ /* The LAW 0xe0000000 ~ 0xefffffff for BCSR and NOR flash */
+ SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
--- /dev/null
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * Authors: Roy Zang <tie-fei.zang@freescale.com>
+ * Chunhe Lan <b25806@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/io.h>
+#include <asm/cache.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_portals.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <netdev.h>
+#include <malloc.h>
+
+#include "bcsr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ fsl_lbc_t *lbc = LBC_BASE_ADDR;
+
+ /* Set ABSWP to implement conversion of addresses in the LBC */
+ setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ u8 *bcsr = (u8 *)BCSR_ACCESS_REG_ADDR;
+
+ printf("Board: P1023 RDS\n");
+
+ clrbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG_CLR);
+ setbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG0);
+
+ return 0;
+}
+
+/* Fixed sdram init -- doesn't use serial presence detect. */
+phys_size_t fixed_sdram(void)
+{
+#ifndef CONFIG_SYS_RAMBOOT
+ ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR;
+
+ set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
+
+ out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
+ out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG);
+ out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS);
+ out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG);
+ out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+ out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL2);
+ out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1);
+ out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2);
+ out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT);
+ out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL);
+ out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4);
+ out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5);
+ out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL);
+ out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL);
+ out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1);
+ out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2);
+ out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
+#endif
+ return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024ul;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+#endif
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_BCSR_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash + BCSR region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash + bcsr */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_BCSR_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+ setup_portals();
+
+ return 0;
+}
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+ return gd->bus_clk;
+}
+
+unsigned long get_board_ddr_clk(ulong dummy)
+{
+ return gd->mem_clk;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ return pci_eth_init(bis);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+}
+#endif
--- /dev/null
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_4M, 1),
+
+#ifndef CONFIG_NAND_SPL
+ /* *W*G* - BCSR and NOR flash on local bus*/
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000,
+ CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000,
+ CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 7, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 8, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
+ 0, 9, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_1M, 1),
+#endif
+
+ /* *I*G - NAND */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 11, BOOKE_PAGESZ_1M, 1),
+
+#ifdef CONFIG_SYS_RAMBOOT
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE,
+ CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 12, BOOKE_PAGESZ_1G, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 13, BOOKE_PAGESZ_1G, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
P1020RDB_SPIFLASH powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P1020RDB,SPIFLASH
P1022DS powerpc mpc85xx p1022ds freescale
P1022DS_36BIT powerpc mpc85xx p1022ds freescale - P1022DS:36BIT
+P1023RDS powerpc mpc85xx p1023rds freescale - P1023RDS
+P1023RDS_NAND powerpc mpc85xx p1023rds freescale - P1023RDS:NAND
P2010RDB powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2010RDB
P2010RDB_36BIT powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2010RDB,36BIT
P2010RDB_36BIT_SDCARD powerpc mpc85xx p1_p2_rdb freescale - P1_P2_RDB:P2010RDB,36BIT,SDCARD
--- /dev/null
+Overview
+--------
+The P1023 process includes a performance optimized implementation of the
+QorIQ data Path Acceleration Architecture (DPAA). This architecture
+provides the infrastructure to support simplified sharing of networking
+interfaces and accelerators by multiple CPU cores. P1023 is an e500 based
+dual core SOC.
+
+P1023RDS board is a Low End Dual core platform supporting the P1023
+processor of QorIQ series.
+
+Building U-boot
+---------------
+To build the u-boot for P1023RDS:
+Configure to NOR boot:
+ make P1023RDS_config
+Configure to NAND boot:
+ make P1023RDS_NAND_config
+Build:
+ make
+
+Board Switches
+--------------
+Most switches on the board should not be changed. The most frequent
+user-settable switches on the board are used to configure
+the flash banks.
+
+J4: all open
+
+Default NOR flash boot switch setting:
+ Sw3[1:8]: off on on off on on off off
+ Sw4[1:8]: off off off on off off off off
+ Sw6[1:8]: off on off on off on on off
+ Sw7[1:8]: off on off off on off off off
+ Sw8[1:8]: on off off off off off off off
+
+For NAND flash boot,set
+Sw4[1:4]: off on on on
+
+The default native ethernet setting is for RGMII mode.
+To use SGMII mode, set
+SW8[1:2]: OFF OFF
+SW7[6:7]: ON ON
+
+Memory Map
+----------
+0x0000_0000 0x7fff_ffff DDR 2G Cacheable
+0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
+0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
+0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
+
+0xe000_0000 0xe003_ffff BCSR 256K BCSR
+0xee00_0000 0xefff_ffff NOR flash 32M NOR flash
+0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M
+0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
+0xffa0_0000 0xffaf_ffff NAND FLASH 1M non-cacheable
+0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
+
+Flashing u-boot Images
+---------------
+To program the image in the boot flash bank:
+NOR flash boot:
+ => tftp 1000000 u-boot.bin
+ => protect off all
+ => erase eff80000 efffffff
+ => cp.b 1000000 eff80000 80000
+
+NAND flash boot:
+ => tftp 1000000 u-boot-nand.bin
+ => nand erase 0 80000
+ => nand write 1000000 0 80000
+
+Firmware ucode location
+---------------------------------
+Microcode(ucode) to FMAN's IRAM is needed to make FMAN Ethernet work.
+u-boot loads ucode FLASH. The location for ucode:
+NOR Flash: 0xfe000000
+NAND Flash: 0x1f00000
+
+Using the Device Tree Source File
+---------------------------------
+To create the DTB (Device Tree Binary) image file,
+use a command similar to this:
+
+ dtc -b 0 -f -I dts -O dtb p1023rds.dts > p1023rds.dtb
+
+Likely, that .dts file will come from here;
+
+ linux-2.6/arch/powerpc/boot/dts/p1023rds.dts
+or
+ make p1023rds.dtb ARCH=powerpc
+in linux-2.6 directory.
+
+Booting Linux
+-------------
+Place a linux uImage in the TFTP disk area.
+
+ tftp 1000000 uImage
+ tftp 2000000 rootfs.ext2.gz.uboot
+ tftp c00000 p1023rds.dtb
+ bootm 1000000 2000000 c00000
--- /dev/null
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * Authors: Roy Zang <tie-fei.zang@freescale.com>
+ * Chunhe Lan <b25806@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * p1023rds board configuration file
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#ifdef CONFIG_NAND
+#define CONFIG_NAND_U_BOOT
+#define CONFIG_RAMBOOT_NAND
+#endif
+
+#ifdef CONFIG_NAND_U_BOOT
+#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000
+#define CONFIG_SYS_TEXT_BASE 0x11001000
+
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
+#else
+#define CONFIG_SYS_LDSCRIPT $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#endif /* CONFIG_NAND_SPL */
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff80000
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE /* BOOKE */
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_MPC85xx
+#define CONFIG_P1023
+#define CONFIG_P1023RDS
+#define CONFIG_MP /* support multiple processors */
+
+#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE3 /* PCIE controler 3 (slot 3) */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_clock_freq(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ 66666666
+#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_HWCONFIG
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x1fffffff /* fix me, only 1G */
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+#define CONFIG_SYS_LBC_LBCR 0x00000000 /* Implement conversion of
+ addresses in the LBC */
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff600000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xff600000 /* relocated CCSRBAR */
+/* physical addr of CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+
+/* DDR Setup */
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+
+/* These are used when DDR doesn't use SPD. */
+#define CONFIG_SYS_SDRAM_SIZE 2048u /* DDR is 2GB */
+
+/* Default settings for "stable" mode */
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F
+#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007F
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
+#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302
+#define CONFIG_SYS_DDR_TIMING_3 0x00020000
+#define CONFIG_SYS_DDR_TIMING_0 0x40110104
+#define CONFIG_SYS_DDR_TIMING_1 0x5C59E544
+#define CONFIG_SYS_DDR_TIMING_2 0x0fA888CA
+#define CONFIG_SYS_DDR_MODE_1 0x00441210
+#define CONFIG_SYS_DDR_MODE_2 0x00000000
+#define CONFIG_SYS_DDR_MODE_CTRL 0x00000000
+#define CONFIG_SYS_DDR_INTERVAL 0x0A280100
+#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
+#define CONFIG_SYS_DDR_CLK_CTRL 0x01800000
+#define CONFIG_SYS_DDR_TIMING_4 0x00000001
+#define CONFIG_SYS_DDR_TIMING_5 0x01401400
+#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600
+#define CONFIG_SYS_DDR_WRLVL_CNTL 0x8675F605
+#define CONFIG_SYS_DDR_CONTROL 0xC70C0008 /* Type = DDR3: No Interleaving */
+#define CONFIG_SYS_DDR_CONTROL2 0x24401010
+#define CONFIG_SYS_DDR_CDR1 0x00000000
+#define CONFIG_SYS_DDR_CDR2 0x00000000
+
+#define CONFIG_SYS_DDR_ERR_INT_EN 0x00000000
+#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
+#define CONFIG_SYS_DDR_SBE 0x00000000
+
+/* Settings that differ for "performance" mode */
+#define CONFIG_SYS_DDR_CS0_BNDS_PERF 0x0000007F /* Interleaving Enabled */
+#define CONFIG_SYS_DDR_CS1_BNDS_PERF 0x00000000 /* Interleaving Enabled */
+#define CONFIG_SYS_DDR_CS1_CONFIG_PERF 0x80014302
+#define CONFIG_SYS_DDR_TIMING_1_PERF 0x5C58E544
+#define CONFIG_SYS_DDR_TIMING_2_PERF 0x0FA888CA
+/* Type = DDR3: cs0-cs1 interleaving */
+#define CONFIG_SYS_DDR_CONTROL_PERF 0xC70C4008
+#define CONFIG_SYS_DDR_CDR_1 0x00000000
+#define CONFIG_SYS_DDR_CDR_2 0x00000000
+
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
+ * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
+ * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
+ * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
+ *
+ * Localbus non-cacheable
+ * 0xe000_0000 0xe003_ffff BCSR 256K BCSR
+ * 0xee00_0000 0xefff_ffff NOR flash 32M NOR flash
+ * 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M
+ * 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
+ * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
+ * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CONFIG_SYS_BCSR_BASE 0xe0000000 /* start of on board FPGA */
+#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE
+
+#ifndef CONFIG_NAND
+#define CONFIG_SYS_FLASH_BASE 0xee000000 /* start of FLASH 32M */
+
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
+ | BR_PS_16 | BR_V)
+#define CONFIG_FLASH_OR_PRELIM 0xfe000ff7
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#else
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#if defined(CONFIG_SYS_SPL) || defined(CONFIG_RAMBOOT_NAND)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f function */
+#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+ (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
+
+#ifndef CONFIG_NAND_SPL
+#define CONFIG_SYS_NAND_BASE 0xffa00000
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+#else
+#define CONFIG_SYS_NAND_BASE 0xfff00000
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+#endif
+
+#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_NAND_FSL_ELBC
+#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
+
+/* NAND boot: 4K NAND loader config */
+#define CONFIG_SYS_NAND_SPL_SIZE 0x1000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) + CONFIG_SYS_NAND_SPL_SIZE)
+#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000 - CONFIG_SYS_NAND_SPL_SIZE)
+#define CONFIG_SYS_NAND_U_BOOT_START 0x11000000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (0)
+#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
+#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)
+
+/* NAND flash config */
+#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
+ | BR_PS_8 /* Port Size = 8bit */ \
+ | BR_MS_FCM /* MSEL = FCM */ \
+ | BR_V) /* valid */
+#define CONFIG_SYS_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \
+ | OR_FCM_CSCT \
+ | OR_FCM_CST \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_1 \
+ | OR_FCM_TRLX \
+ | OR_FCM_EHTR)
+
+#ifdef CONFIG_RAMBOOT_NAND
+/* NAND Base Address */
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+/* chip select 1 - BCSR */
+#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
+ | BR_MS_GPCM | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
+ | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+#else
+#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
+#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
+/* chip select 1 - BCSR */
+#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
+ | BR_MS_GPCM | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
+ | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+#endif
+
+/* Serial Port
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_NS16550_MIN_FUNCTIONS
+#endif
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+#define CONFIG_SYS_64BIT_VSPRINTF
+#define CONFIG_SYS_64BIT_STRTOUL
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+
+/*
+ * I2C2 EEPROM
+ */
+#define CONFIG_ID_EEPROM
+#ifdef CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#endif
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+
+#define CONFIG_CMD_I2C
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+
+#define CONFIG_HARD_SPI
+#define CONFIG_FSL_ESPI
+
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 3, Slot 1, tgtid 3, Base address b000 */
+#define CONFIG_SYS_PCIE3_NAME "Slot 3"
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 2, direct to uli, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME "Slot 2"
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 1, Slot 2, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME "Slot 1"
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+#if defined(CONFIG_PCI)
+#define CONFIG_E1000 /* Defind e1000 pci Ethernet card */
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#endif /* CONFIG_PCI */
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_NAND)
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x4000)
+#define CONFIG_ENV_SIZE 0x2000
+#endif
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR 0xfff80000
+#else
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#endif
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * USB
+ */
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_BOOTFILE uImage
+#define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE 115200
+
+/* Qman/Bman */
+#define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */
+#define CONFIG_SYS_QMAN_MEM_BASE 0xff000000
+#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_BMAN_MEM_BASE 0xff200000
+#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
+
+/* For FM */
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#endif
+
+#ifndef CONFIG_NAND
+/* Default address of microcode for the Linux Fman driver */
+/* QE microcode/firmware address */
+#define CONFIG_SYS_FMAN_FW_ADDR 0xEF000000
+#define CONFIG_SYS_FMAN_FW_ADDR_PHYS CONFIG_SYS_FMAN_FW_ADDR
+#else
+#define CONFIG_SYS_QE_FW_IN_NAND 0x1f00000
+#define CONFIG_SYS_FMAN_FW_ADDR 0x10000000
+#define CONFIG_SYS_FMAN_FW_LENGTH 0x10000
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2
+#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x7
+
+#define CONFIG_SYS_TBIPA_VALUE 8
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1@DTSEC1"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
+
+#endif /* __CONFIG_H */
--- /dev/null
+#
+# Copyright 2010-2011 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+NAND_SPL := y
+PAD_TO := 0xfff01000
+
+include $(TOPDIR)/config.mk
+
+nandobj := $(OBJTREE)/nand_spl/
+
+LDSCRIPT= $(TOPDIR)/$(CPUDIR)/u-boot-nand_spl.lds
+LDFLAGS := -T $(nandobj)u-boot-nand_spl.lds -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) \
+ $(LDFLAGS) $(LDFLAGS_FINAL)
+AFLAGS += -DCONFIG_NAND_SPL
+CFLAGS += -DCONFIG_NAND_SPL
+
+SOBJS = start.o resetvec.o
+COBJS = cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \
+ nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o
+
+SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS := $(SOBJS) $(COBJS)
+LNDIR := $(nandobj)board/$(BOARDDIR)
+
+ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+
+all: $(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
+ $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
+
+$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl
+ $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \
+ -Map $(nandobj)u-boot-spl.map \
+ -o $(nandobj)u-boot-spl
+
+$(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT)
+ $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
+
+# create symbolic links for common files
+
+$(obj)cache.c:
+ @rm -f $(obj)cache.c
+ ln -sf $(SRCTREE)/arch/powerpc/lib/cache.c $(obj)cache.c
+
+$(obj)cpu_init_early.c:
+ @rm -f $(obj)cpu_init_early.c
+ ln -sf $(SRCTREE)/$(CPUDIR)/cpu_init_early.c $(obj)cpu_init_early.c
+
+$(obj)cpu_init_nand.c:
+ @rm -f $(obj)cpu_init_nand.c
+ ln -sf $(SRCTREE)/$(CPUDIR)/cpu_init_nand.c $(obj)cpu_init_nand.c
+
+$(obj)fsl_law.c:
+ @rm -f $(obj)fsl_law.c
+ ln -sf $(SRCTREE)/drivers/misc/fsl_law.c $(obj)fsl_law.c
+
+$(obj)law.c:
+ @rm -f $(obj)law.c
+ ln -sf $(SRCTREE)/board/$(BOARDDIR)/law.c $(obj)law.c
+
+$(obj)nand_boot_fsl_elbc.c:
+ @rm -f $(obj)nand_boot_fsl_elbc.c
+ ln -sf $(SRCTREE)/nand_spl/nand_boot_fsl_elbc.c \
+ $(obj)nand_boot_fsl_elbc.c
+
+$(obj)ns16550.c:
+ @rm -f $(obj)ns16550.c
+ ln -sf $(SRCTREE)/drivers/serial/ns16550.c $(obj)ns16550.c
+
+$(obj)resetvec.S:
+ @rm -f $(obj)resetvec.S
+ ln -s $(SRCTREE)/$(CPUDIR)/resetvec.S $(obj)resetvec.S
+
+$(obj)fixed_ivor.S:
+ @rm -f $(obj)fixed_ivor.S
+ ln -sf $(SRCTREE)/$(CPUDIR)/fixed_ivor.S $(obj)fixed_ivor.S
+
+$(obj)start.S: $(obj)fixed_ivor.S
+ @rm -f $(obj)start.S
+ ln -sf $(SRCTREE)/$(CPUDIR)/start.S $(obj)start.S
+
+$(obj)tlb.c:
+ @rm -f $(obj)tlb.c
+ ln -sf $(SRCTREE)/$(CPUDIR)/tlb.c $(obj)tlb.c
+
+$(obj)tlb_table.c:
+ @rm -f $(obj)tlb_table.c
+ ln -sf $(SRCTREE)/board/$(BOARDDIR)/tlb.c $(obj)tlb_table.c
+
+ifneq ($(OBJTREE), $(SRCTREE))
+$(obj)nand_boot.c:
+ @rm -f $(obj)nand_boot.c
+ ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c $(obj)nand_boot.c
+endif
+
+#########################################################################
+
+$(obj)%.o: $(obj)%.S
+ $(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o: $(obj)%.c
+ $(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * Author: Roy Zang <tie-fei.zang@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ *
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <asm/io.h>
+#include <nand.h>
+#include <asm/fsl_law.h>
+
+/* Fixed sdram init -- doesn't use serial presence detect. */
+void sdram_init(void)
+{
+ ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR;
+
+ set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
+
+ out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
+ out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG);
+ out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS);
+ out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG);
+ out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+ out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL2);
+ out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1);
+ out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2);
+ out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT);
+ out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL);
+ out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4);
+ out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5);
+ out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL);
+ out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL);
+ out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1);
+ out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2);
+ out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
+}
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio, bus_clk;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ /* initialize selected port with appropriate baud rate */
+ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+ plat_ratio >>= 1;
+ bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ bus_clk / 16 / CONFIG_BAUDRATE);
+
+ puts("\nNAND boot... ");
+ /* Initialize the DDR3 */
+ sdram_init();
+ /* copy code to RAM and jump to it - this should not return */
+ /* NOTE - code has to be copied out of NAND buffer before
+ * other blocks can be read.
+ */
+ relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, 0,
+ CONFIG_SYS_NAND_U_BOOT_RELOC);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ nand_boot();
+}
+
+void putc(char c)
+{
+ if (c == '\n')
+ NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
+
+ NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
+}
+
+void puts(const char *str)
+{
+ while (*str)
+ putc(*str++);
+}
projects / u-boot.git / commitdiff