--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc-child.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: device tree bindings for children of the Texas Instruments GPMC
+
+maintainers:
+ - Tony Lindgren <tony@atomide.com>
+ - Roger Quadros <rogerq@kernel.org>
+
+description:
+ This binding is meant for the child nodes of the GPMC node. The node
+ represents any device connected to the GPMC bus. It may be a Flash chip,
+ RAM chip or Ethernet controller, etc. These properties are meant for
+ configuring the GPMC settings/timings and will accompany the bindings
+ supported by the respective device.
+
+properties:
+ reg: true
+
+# GPMC Timing properties for child nodes. All are optional and default to 0.
+ gpmc,sync-clk-ps:
+ description: Minimum clock period for synchronous mode
+ default: 0
+
+# Chip-select signal timings corresponding to GPMC_CONFIG2:
+ gpmc,cs-on-ns:
+ description: Assertion time
+ default: 0
+
+ gpmc,cs-rd-off-ns:
+ description: Read deassertion time
+ default: 0
+
+ gpmc,cs-wr-off-ns:
+ description: Write deassertion time
+ default: 0
+
+# ADV signal timings corresponding to GPMC_CONFIG3:
+ gpmc,adv-on-ns:
+ description: Assertion time
+ default: 0
+
+ gpmc,adv-rd-off-ns:
+ description: Read deassertion time
+ default: 0
+
+ gpmc,adv-wr-off-ns:
+ description: Write deassertion time
+ default: 0
+
+ gpmc,adv-aad-mux-on-ns:
+ description: Assertion time for AAD
+ default: 0
+
+ gpmc,adv-aad-mux-rd-off-ns:
+ description: Read deassertion time for AAD
+ default: 0
+
+ gpmc,adv-aad-mux-wr-off-ns:
+ description: Write deassertion time for AAD
+ default: 0
+
+# WE signals timings corresponding to GPMC_CONFIG4:
+ gpmc,we-on-ns:
+ description: Assertion time
+ default: 0
+
+ gpmc,we-off-ns:
+ description: Deassertion time
+ default: 0
+
+# OE signals timings corresponding to GPMC_CONFIG4:
+ gpmc,oe-on-ns:
+ description: Assertion time
+ default: 0
+
+ gpmc,oe-off-ns:
+ description: Deassertion time
+ default: 0
+
+ gpmc,oe-aad-mux-on-ns:
+ description: Assertion time for AAD
+ default: 0
+
+ gpmc,oe-aad-mux-off-ns:
+ description: Deassertion time for AAD
+ default: 0
+
+# Access time and cycle time timings (in nanoseconds) corresponding to
+# GPMC_CONFIG5:
+ gpmc,page-burst-access-ns:
+ description: Multiple access word delay
+ default: 0
+
+ gpmc,access-ns:
+ description: Start-cycle to first data valid delay
+ default: 0
+
+ gpmc,rd-cycle-ns:
+ description: Total read cycle time
+ default: 0
+
+ gpmc,wr-cycle-ns:
+ description: Total write cycle time
+ default: 0
+
+ gpmc,bus-turnaround-ns:
+ description: Turn-around time between successive accesses
+ default: 0
+
+ gpmc,cycle2cycle-delay-ns:
+ description: Delay between chip-select pulses
+ default: 0
+
+ gpmc,clk-activation-ns:
+ description: GPMC clock activation time
+ default: 0
+
+ gpmc,wait-monitoring-ns:
+ description: Start of wait monitoring with regard to valid data
+ default: 0
+
+# Boolean timing parameters. If property is present, parameter is enabled
+# otherwise disabled.
+ gpmc,adv-extra-delay:
+ description: ADV signal is delayed by half GPMC clock
+ type: boolean
+
+ gpmc,cs-extra-delay:
+ description: CS signal is delayed by half GPMC clock
+ type: boolean
+
+ gpmc,cycle2cycle-diffcsen:
+ description: |
+ Add "cycle2cycle-delay" between successive accesses
+ to a different CS
+ type: boolean
+
+ gpmc,cycle2cycle-samecsen:
+ description: |
+ Add "cycle2cycle-delay" between successive accesses
+ to the same CS
+ type: boolean
+
+ gpmc,oe-extra-delay:
+ description: OE signal is delayed by half GPMC clock
+ type: boolean
+
+ gpmc,we-extra-delay:
+ description: WE signal is delayed by half GPMC clock
+ type: boolean
+
+ gpmc,time-para-granularity:
+ description: Multiply all access times by 2
+ type: boolean
+
+# The following two properties are applicable only to OMAP3+ and AM335x:
+ gpmc,wr-access-ns:
+ description: |
+ In synchronous write mode, for single or
+ burst accesses, defines the number of
+ GPMC_FCLK cycles from start access time
+ to the GPMC_CLK rising edge used by the
+ memory device for the first data capture.
+ default: 0
+
+ gpmc,wr-data-mux-bus-ns:
+ description: |
+ In address-data multiplex mode, specifies
+ the time when the first data is driven on
+ the address-data bus.
+ default: 0
+
+# GPMC chip-select settings properties for child nodes. All are optional.
+ gpmc,burst-length:
+ description: Page/burst length.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 4, 8, 16]
+ default: 0
+
+ gpmc,burst-wrap:
+ description: Enables wrap bursting
+ type: boolean
+
+ gpmc,burst-read:
+ description: Enables read page/burst mode
+ type: boolean
+
+ gpmc,burst-write:
+ description: Enables write page/burst mode
+ type: boolean
+
+ gpmc,device-width:
+ description: |
+ Total width of device(s) connected to a GPMC
+ chip-select in bytes. The GPMC supports 8-bit
+ and 16-bit devices and so this property must be
+ 1 or 2.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2]
+ default: 1
+
+ gpmc,mux-add-data:
+ description: |
+ Address and data multiplexing configuration.
+ Valid values are
+ 0 for Non multiplexed mode
+ 1 for address-address-data multiplexing mode and
+ 2 for address-data multiplexing mode.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
+
+ gpmc,sync-read:
+ description: |
+ Enables synchronous read. Defaults to asynchronous
+ is this is not set.
+ type: boolean
+
+ gpmc,sync-write:
+ description: |
+ Enables synchronous writes. Defaults to asynchronous
+ is this is not set.
+ type: boolean
+
+ gpmc,wait-pin:
+ description: |
+ Wait-pin used by client. Must be less than "gpmc,num-waitpins".
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ gpmc,wait-pin-polarity:
+ description: |
+ Set the desired polarity for the selected wait pin.
+ 0 for active low, 1 for active high.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
+
+ gpmc,wait-on-read:
+ description: Enables wait monitoring on reads.
+ type: boolean
+
+ gpmc,wait-on-write:
+ description: Enables wait monitoring on writes.
+ type: boolean
+
+required:
+ - reg
+
+# the GPMC child will have its own native properties
+additionalProperties: true
--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments GPMC Memory Controller device-tree bindings
+
+maintainers:
+ - Tony Lindgren <tony@atomide.com>
+ - Roger Quadros <rogerq@kernel.org>
+
+description:
+ The GPMC is a unified memory controller dedicated for interfacing
+ with external memory devices like
+ - Asynchronous SRAM-like memories and ASICs
+ - Asynchronous, synchronous, and page mode burst NOR flash
+ - NAND flash
+ - Pseudo-SRAM devices
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - ti,am3352-gpmc
+ - ti,am64-gpmc
+ - ti,omap2420-gpmc
+ - ti,omap2430-gpmc
+ - ti,omap3430-gpmc
+ - ti,omap4430-gpmc
+
+ reg:
+ minItems: 1
+ maxItems: 2
+
+ reg-names:
+ items:
+ - const: cfg
+ - const: data
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+ description: |
+ Functional clock. Used for bus timing calculations and
+ GPMC configuration.
+
+ clock-names:
+ items:
+ - const: fck
+
+ power-domains:
+ maxItems: 1
+
+ dmas:
+ items:
+ - description: DMA channel for GPMC NAND prefetch
+
+ dma-names:
+ items:
+ - const: rxtx
+
+ "#address-cells": true
+
+ "#size-cells": true
+
+ gpmc,num-cs:
+ description: maximum number of supported chip-select lines.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ gpmc,num-waitpins:
+ description: maximum number of supported wait pins.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ ranges:
+ minItems: 1
+ description: |
+ Must be set up to reflect the memory layout with four
+ integer values for each chip-select line in use,
+ <cs-number> 0 <physical address of mapping> <size>
+ items:
+ - description: NAND bank 0
+ - description: NOR/SRAM bank 0
+ - description: NOR/SRAM bank 1
+
+ '#interrupt-cells':
+ const: 2
+
+ interrupt-controller:
+ description: |
+ The GPMC driver implements and interrupt controller for
+ the NAND events "fifoevent" and "termcount" plus the
+ rising/falling edges on the GPMC_WAIT pins.
+ The interrupt number mapping is as follows
+ 0 - NAND_fifoevent
+ 1 - NAND_termcount
+ 2 - GPMC_WAIT0 pin edge
+ 3 - GPMC_WAIT1 pin edge, and so on.
+
+ '#gpio-cells':
+ const: 2
+
+ gpio-controller:
+ description: |
+ The GPMC driver implements a GPIO controller for the
+ GPMC WAIT pins that can be used as general purpose inputs.
+ 0 maps to GPMC_WAIT0 pin.
+
+ ti,hwmods:
+ description:
+ Name of the HWMOD associated with GPMC. This is for legacy
+ omap2/3 platforms only.
+ $ref: /schemas/types.yaml#/definitions/string
+ deprecated: true
+
+ ti,no-idle-on-init:
+ description:
+ Prevent idling the module at init. This is for legacy omap2/3
+ platforms only.
+ type: boolean
+ deprecated: true
+
+patternProperties:
+ "@[0-7],[a-f0-9]+$":
+ type: object
+ description: |
+ The child device node represents the device connected to the GPMC
+ bus. The device can be a NAND chip, SRAM device, NOR device
+ or an ASIC.
+ $ref: "ti,gpmc-child.yaml"
+
+
+required:
+ - compatible
+ - reg
+ - gpmc,num-cs
+ - gpmc,num-waitpins
+ - "#address-cells"
+ - "#size-cells"
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: ti,am64-gpmc
+ then:
+ required:
+ - reg-names
+ - power-domains
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/gpio/gpio.h>
+
+ gpmc: memory-controller@50000000 {
+ compatible = "ti,am3352-gpmc";
+ reg = <0x50000000 0x2000>;
+ interrupts = <100>;
+ clocks = <&l3s_clkctrl>;
+ clock-names = "fck";
+ dmas = <&edma 52 0>;
+ dma-names = "rxtx";
+ gpmc,num-cs = <8>;
+ gpmc,num-waitpins = <2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ nand@0,0 {
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4>;
+ interrupt-parent = <&gpmc>;
+ interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+ <1 IRQ_TYPE_NONE>; /* termcount */
+ ti,nand-xfer-type = "prefetch-dma";
+ ti,nand-ecc-opt = "bch16";
+ ti,elm-id = <&elm>;
+ rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
+ };
+ };
projects / u-boot.git / commitdiff