--- /dev/null
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * TAISHAN.h - configuration for AMCC 440GX Ref
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_TAISHAN 1 /* Board is taishan */
+#define CONFIG_440GX 1 /* Specifc GX support */
+#define CONFIG_4xx 1 /* ... PPC4xx family */
+#undef CFG_DRAM_TEST /* Disable-takes long time! */
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
+#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
+#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
+#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
+#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
+
+#define CFG_EBC0_FLASH_BASE CFG_FLASH_BASE
+#define CFG_EBC1_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x01000000)
+#define CFG_EBC2_LCM_BASE (CFG_PERIPHERAL_BASE + 0x02000000)
+#define CFG_EBC3_CONN_BASE (CFG_PERIPHERAL_BASE + 0x08000000)
+
+#define CFG_GPIO_BASE (CFG_PERIPHERAL_BASE + 0x00000700)
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in internal SRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_TEMP_STACK_OCM 1
+#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE
+#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM*/
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data*/
+
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
+#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
+#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc*/
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_UART1_CONSOLE 1 /* use of UART1 as console */
+#define CONFIG_SERIAL_MULTI 1 /* enable serial multi support */
+#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
+#define CONFIG_BAUDRATE 115200
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * E2PROM bootstrap configure value
+ *----------------------------------------------------------------------*/
+
+/*
+ * 800/133/66
+ * IIC 0~15: 86 78 11 6a 61 A7 04 62 00 00 00 00 00 00 00 00
+ */
+
+/*
+ * 800/160/80
+ * IIC 0~15: 86 78 c1 a6 09 67 04 63 00 00 00 00 00 00 00 00
+ */
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */
+#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */
+#define CFG_SDRAM0_TR0 0xC10A401A
+#undef CONFIG_SDRAM_ECC /* enable ECC support */
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#undef CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR 0x50
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+#define CFG_BOOTSTRAP_IIC_ADDR 0x50
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible) */
+#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
+#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
+#define CFG_DTT_MAX_TEMP 70
+#define CFG_DTT_LOW_TEMP -30
+#define CFG_DTT_HYSTERESIS 3
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "hostname=taishan\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\
+ "flash_nfs=run nfsargs addip addtty;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip addtty;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
+ "bootm\0" \
+ "rootpath=/opt/eldk/ppc_4xx\0" \
+ "bootfile=/tftpboot/taishan/uImage\0" \
+ "kernel_addr=fc000000\0" \
+ "ramdisk_addr=fc180000\0" \
+ "load=tftp 100000 /tftpboot/taishan/u-boot.bin\0" \
+ "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
+ "cp.b 100000 fffc0000 40000;" \
+ "setenv filesize;saveenv\0" \
+ "upd=run load;run update\0" \
+ "fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
+ "$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0" \
+ "dhcp=setenv bootargs $(bootargs) ip=dhcp\0" \
+ "kozio=bootm 0xffe00000\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*-----------------------------------------------------------------------
+ * Networking
+ *----------------------------------------------------------------------*/
+#define CONFIG_EMAC_NR_START 2 /* start with EMAC 2 (skip 0&1) */
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_NET_MULTI 1
+#define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */
+#define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */
+#define CONFIG_PHY2_ADDR 0x1
+#define CONFIG_PHY3_ADDR 0x3
+#define CONFIG_ET1011C_PHY 1
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#define CONFIG_HAS_ETH3
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
+#define CONFIG_PHY_RESET_DELAY 1000
+#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+
+/*-----------------------------------------------------------------------
+ * Console/Commands/Parser
+ *----------------------------------------------------------------------*/
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DIAG | \
+ CFG_CMD_DTT | \
+ CFG_CMD_ELF | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_MII | \
+ CFG_CMD_NET | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PCI | \
+ CFG_CMD_PING | \
+ CFG_CMD_REGINFO)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+/* General PCI */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_EEPRO100 1 /* include PCI EEPRO100 */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
+
+/* Board-specific PCI */
+#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
+#define CFG_PCI_TARGET_INIT /* let board init pci target */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
+#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ *----------------------------------------------------------------------*/
+#define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff