--- /dev/null
+/*
+ * Copyright (C) Marvell International Ltd. and its affiliates
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#ifndef __BOARD_ENV_SPEC
+#define __BOARD_ENV_SPEC
+
+/* Board specific configuration */
+
+/* KW40 */
+#define MV_6710_DEV_ID 0x6710
+
+#define MV_6710_Z1_REV 0x0
+#define MV_6710_Z1_ID ((MV_6710_DEV_ID << 16) | MV_6710_Z1_REV)
+#define MV_6710_Z1_NAME "MV6710 Z1"
+
+/* Armada XP Family */
+#define MV_78130_DEV_ID 0x7813
+#define MV_78160_DEV_ID 0x7816
+#define MV_78230_DEV_ID 0x7823
+#define MV_78260_DEV_ID 0x7826
+#define MV_78460_DEV_ID 0x7846
+#define MV_78000_DEV_ID 0x7888
+
+#define MV_FPGA_DEV_ID 0x2107
+
+#define MV_78XX0_Z1_REV 0x0
+
+/* boards ID numbers */
+#define BOARD_ID_BASE 0x0
+
+/* New board ID numbers */
+#define DB_88F78XX0_BP_ID (BOARD_ID_BASE)
+#define RD_78460_SERVER_ID (DB_88F78XX0_BP_ID + 1)
+#define DB_78X60_PCAC_ID (RD_78460_SERVER_ID + 1)
+#define FPGA_88F78XX0_ID (DB_78X60_PCAC_ID + 1)
+#define DB_88F78XX0_BP_REV2_ID (FPGA_88F78XX0_ID + 1)
+#define RD_78460_NAS_ID (DB_88F78XX0_BP_REV2_ID + 1)
+#define DB_78X60_AMC_ID (RD_78460_NAS_ID + 1)
+#define DB_78X60_PCAC_REV2_ID (DB_78X60_AMC_ID + 1)
+#define RD_78460_SERVER_REV2_ID (DB_78X60_PCAC_REV2_ID + 1)
+#define DB_784MP_GP_ID (RD_78460_SERVER_REV2_ID + 1)
+#define RD_78460_CUSTOMER_ID (DB_784MP_GP_ID + 1)
+#define MV_MAX_BOARD_ID (RD_78460_CUSTOMER_ID + 1)
+#define INVALID_BAORD_ID 0xFFFFFFFF
+
+/* Sample at Reset */
+#define MPP_SAMPLE_AT_RESET(id) (0x18230 + (id * 4))
+
+/* BIOS Modes related defines */
+
+#define SAR0_BOOTWIDTH_OFFSET 3
+#define SAR0_BOOTWIDTH_MASK (0x3 << SAR0_BOOTWIDTH_OFFSET)
+#define SAR0_BOOTSRC_OFFSET 5
+#define SAR0_BOOTSRC_MASK (0xF << SAR0_BOOTSRC_OFFSET)
+
+#define SAR0_L2_SIZE_OFFSET 19
+#define SAR0_L2_SIZE_MASK (0x3 << SAR0_L2_SIZE_OFFSET)
+#define SAR0_CPU_FREQ_OFFSET 21
+#define SAR0_CPU_FREQ_MASK (0x7 << SAR0_CPU_FREQ_OFFSET)
+#define SAR0_FABRIC_FREQ_OFFSET 24
+#define SAR0_FABRIC_FREQ_MASK (0xF << SAR0_FABRIC_FREQ_OFFSET)
+#define SAR0_CPU0CORE_OFFSET 31
+#define SAR0_CPU0CORE_MASK (0x1 << SAR0_CPU0CORE_OFFSET)
+#define SAR1_CPU0CORE_OFFSET 0
+#define SAR1_CPU0CORE_MASK (0x1 << SAR1_CPU0CORE_OFFSET)
+
+#define PEX_CLK_100MHZ_OFFSET 2
+#define PEX_CLK_100MHZ_MASK (0x1 << PEX_CLK_100MHZ_OFFSET)
+
+#define SAR1_FABRIC_MODE_OFFSET 19
+#define SAR1_FABRIC_MODE_MASK (0x1 << SAR1_FABRIC_MODE_OFFSET)
+#define SAR1_CPU_MODE_OFFSET 20
+#define SAR1_CPU_MODE_MASK (0x1 << SAR1_CPU_MODE_OFFSET)
+
+#define SAR_CPU_FAB_GET(cpu, fab) (((cpu & 0x7) << 21) | ((fab & 0xF) << 24))
+
+
+#define CORE_AVS_CONTROL_0REG 0x18300
+#define CORE_AVS_CONTROL_2REG 0x18308
+#define CPU_AVS_CONTROL2_REG 0x20868
+#define CPU_AVS_CONTROL0_REG 0x20860
+#define GENERAL_PURPOSE_RESERVED0_REG 0x182E0
+
+#define MSAR_TCLK_OFFS 28
+#define MSAR_TCLK_MASK (0x1 << MSAR_TCLK_OFFS)
+
+
+/* Controler environment registers offsets */
+#define GEN_PURP_RES_1_REG 0x182F4
+#define GEN_PURP_RES_2_REG 0x182F8
+
+/* registers offsets */
+#define MV_GPP_REGS_OFFSET(unit) (0x18100 + ((unit) * 0x40))
+#define MPP_CONTROL_REG(id) (0x18000 + (id * 4))
+#define MV_GPP_REGS_BASE(unit) (MV_GPP_REGS_OFFSET(unit))
+#define MV_GPP_REGS_BASE_0 (MV_GPP_REGS_OFFSET_0)
+
+#define GPP_DATA_OUT_REG(grp) (MV_GPP_REGS_BASE(grp) + 0x00)
+#define GPP_DATA_OUT_REG_0 (MV_GPP_REGS_BASE_0 + 0x00) /* Used in .S files */
+#define GPP_DATA_OUT_EN_REG(grp) (MV_GPP_REGS_BASE(grp) + 0x04)
+#define GPP_BLINK_EN_REG(grp) (MV_GPP_REGS_BASE(grp) + 0x08)
+#define GPP_DATA_IN_POL_REG(grp) (MV_GPP_REGS_BASE(grp) + 0x0C)
+#define GPP_DATA_IN_REG(grp) (MV_GPP_REGS_BASE(grp) + 0x10)
+#define GPP_INT_CAUSE_REG(grp) (MV_GPP_REGS_BASE(grp) + 0x14)
+#define GPP_INT_MASK_REG(grp) (MV_GPP_REGS_BASE(grp) + 0x18)
+#define GPP_INT_LVL_REG(grp) (MV_GPP_REGS_BASE(grp) + 0x1C)
+#define GPP_OUT_SET_REG(grp) (0x18130 + ((grp) * 0x40))
+#define GPP_64_66_DATA_OUT_SET_REG 0x181A4
+#define GPP_OUT_CLEAR_REG(grp) (0x18134 + ((grp) * 0x40))
+#define GPP_64_66_DATA_OUT_CLEAR_REG 0x181B0
+#define GPP_FUNC_SELECT_REG (MV_GPP_REGS_BASE(0) + 0x40)
+
+#define MV_GPP66 (1 << 2)
+
+/* Relevant for MV78XX0 */
+#define GPP_DATA_OUT_SET_REG (MV_GPP_REGS_BASE(0) + 0x20)
+#define GPP_DATA_OUT_CLEAR_REG (MV_GPP_REGS_BASE(0) + 0x24)
+
+/* This define describes the maximum number of supported PEX Interfaces */
+#define MV_PEX_MAX_IF 10
+#define MV_PEX_MAX_UNIT 4
+
+#define MV_SERDES_NUM_TO_PEX_NUM(num) ((num < 8) ? (num) : (8 + (num / 12)))
+
+#define PEX_PHY_ACCESS_REG(unit) (0x40000 + ((unit) % 2 * 0x40000) + \
+ ((unit)/2 * 0x2000) + 0x1B00)
+
+#define SATA_BASE_REG(port) (0xA2000 + (port)*0x2000)
+
+#define SATA_PWR_PLL_CTRL_REG(port) (SATA_BASE_REG(port) + 0x804)
+#define SATA_DIG_LP_ENA_REG(port) (SATA_BASE_REG(port) + 0x88C)
+#define SATA_REF_CLK_SEL_REG(port) (SATA_BASE_REG(port) + 0x918)
+#define SATA_COMPHY_CTRL_REG(port) (SATA_BASE_REG(port) + 0x920)
+#define SATA_LP_PHY_EXT_CTRL_REG(port) (SATA_BASE_REG(port) + 0x058)
+#define SATA_LP_PHY_EXT_STAT_REG(port) (SATA_BASE_REG(port) + 0x05C)
+#define SATA_IMP_TX_SSC_CTRL_REG(port) (SATA_BASE_REG(port) + 0x810)
+#define SATA_GEN_1_SET_0_REG(port) (SATA_BASE_REG(port) + 0x834)
+#define SATA_GEN_1_SET_1_REG(port) (SATA_BASE_REG(port) + 0x838)
+#define SATA_GEN_2_SET_0_REG(port) (SATA_BASE_REG(port) + 0x83C)
+#define SATA_GEN_2_SET_1_REG(port) (SATA_BASE_REG(port) + 0x840)
+
+#define MV_ETH_BASE_ADDR (0x72000)
+#define MV_ETH_REGS_OFFSET(port) (MV_ETH_BASE_ADDR - ((port) / 2) * \
+ 0x40000 + ((port) % 2) * 0x4000)
+#define MV_ETH_REGS_BASE(port) MV_ETH_REGS_OFFSET(port)
+
+
+#define SGMII_PWR_PLL_CTRL_REG(port) (MV_ETH_REGS_BASE(port) + 0xE04)
+#define SGMII_DIG_LP_ENA_REG(port) (MV_ETH_REGS_BASE(port) + 0xE8C)
+#define SGMII_REF_CLK_SEL_REG(port) (MV_ETH_REGS_BASE(port) + 0xF18)
+#define SGMII_SERDES_CFG_REG(port) (MV_ETH_REGS_BASE(port) + 0x4A0)
+#define SGMII_SERDES_STAT_REG(port) (MV_ETH_REGS_BASE(port) + 0x4A4)
+#define SGMII_COMPHY_CTRL_REG(port) (MV_ETH_REGS_BASE(port) + 0xF20)
+#define QSGMII_GEN_1_SETTING_REG(port) (MV_ETH_REGS_BASE(port) + 0xE38)
+#define QSGMII_SERDES_CFG_REG(port) (MV_ETH_REGS_BASE(port) + 0x4a0)
+
+#define SERDES_LINE_MUX_REG_0_7 0x18270
+#define SERDES_LINE_MUX_REG_8_15 0x18274
+#define QSGMII_CONTROL_1_REG 0x18404
+
+/* SOC_CTRL_REG fields */
+#define SCR_PEX_ENA_OFFS(pex) ((pex) & 0x3)
+#define SCR_PEX_ENA_MASK(pex) (1 << pex)
+
+#define PCIE0_QUADX1_EN (1<<7)
+#define PCIE1_QUADX1_EN (1<<8)
+
+#define SCR_PEX_4BY1_OFFS(pex) ((pex) + 7)
+#define SCR_PEX_4BY1_MASK(pex) (1 << SCR_PEX_4BY1_OFFS(pex))
+
+#define PCIE1_CLK_OUT_EN_OFF 5
+#define PCIE1_CLK_OUT_EN_MASK (1 << PCIE1_CLK_OUT_EN_OFF)
+
+#define PCIE0_CLK_OUT_EN_OFF 4
+#define PCIE0_CLK_OUT_EN_MASK (1 << PCIE0_CLK_OUT_EN_OFF)
+
+#define SCR_PEX0_4BY1_OFFS 7
+#define SCR_PEX0_4BY1_MASK (1 << SCR_PEX0_4BY1_OFFS)
+
+#define SCR_PEX1_4BY1_OFFS 8
+#define SCR_PEX1_4BY1_MASK (1 << SCR_PEX1_4BY1_OFFS)
+
+
+#define MV_MISC_REGS_OFFSET (0x18200)
+#define MV_MISC_REGS_BASE (MV_MISC_REGS_OFFSET)
+#define SOC_CTRL_REG (MV_MISC_REGS_BASE + 0x4)
+
+/*
+ * PCI Express Control and Status Registers
+ */
+#define MAX_PEX_DEVICES 32
+#define MAX_PEX_FUNCS 8
+#define MAX_PEX_BUSSES 256
+
+#define PXSR_PEX_BUS_NUM_OFFS 8 /* Bus Number Indication */
+#define PXSR_PEX_BUS_NUM_MASK (0xff << PXSR_PEX_BUS_NUM_OFFS)
+
+#define PXSR_PEX_DEV_NUM_OFFS 16 /* Device Number Indication */
+#define PXSR_PEX_DEV_NUM_MASK (0x1f << PXSR_PEX_DEV_NUM_OFFS)
+
+#define PXSR_DL_DOWN 0x1 /* DL_Down indication. */
+#define PXCAR_CONFIG_EN (1 << 31)
+#define PEX_STATUS_AND_COMMAND 0x004
+#define PXSAC_MABORT (1 << 29) /* Recieved Master Abort */
+
+/* PCI Express Configuration Address Register */
+
+/* PEX_CFG_ADDR_REG (PXCAR) */
+#define PXCAR_REG_NUM_OFFS 2
+#define PXCAR_REG_NUM_MAX 0x3F
+#define PXCAR_REG_NUM_MASK (PXCAR_REG_NUM_MAX << PXCAR_REG_NUM_OFFS)
+#define PXCAR_FUNC_NUM_OFFS 8
+#define PXCAR_FUNC_NUM_MAX 0x7
+#define PXCAR_FUNC_NUM_MASK (PXCAR_FUNC_NUM_MAX << PXCAR_FUNC_NUM_OFFS)
+#define PXCAR_DEVICE_NUM_OFFS 11
+#define PXCAR_DEVICE_NUM_MAX 0x1F
+#define PXCAR_DEVICE_NUM_MASK (PXCAR_DEVICE_NUM_MAX << PXCAR_DEVICE_NUM_OFFS)
+#define PXCAR_BUS_NUM_OFFS 16
+#define PXCAR_BUS_NUM_MAX 0xFF
+#define PXCAR_BUS_NUM_MASK (PXCAR_BUS_NUM_MAX << PXCAR_BUS_NUM_OFFS)
+#define PXCAR_EXT_REG_NUM_OFFS 24
+#define PXCAR_EXT_REG_NUM_MAX 0xF
+
+#define PXCAR_REAL_EXT_REG_NUM_OFFS 8
+#define PXCAR_REAL_EXT_REG_NUM_MASK (0xF << PXCAR_REAL_EXT_REG_NUM_OFFS)
+
+
+#define PEX_CAPABILITIES_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x60)
+#define PEX_LINK_CAPABILITIES_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x6C)
+#define PEX_LINK_CTRL_STATUS_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x70)
+#define PEX_LINK_CTRL_STATUS2_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x90)
+#define PEX_CTRL_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1A00)
+#define PEX_STATUS_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1A04)
+#define PEX_COMPLT_TMEOUT_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1A10)
+#define PEX_PWR_MNG_EXT_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1A18)
+#define PEX_FLOW_CTRL_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1A20)
+#define PEX_DYNMC_WIDTH_MNG_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1A30)
+#define PEX_ROOT_CMPLX_SSPL_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1A0C)
+#define PEX_RAM_PARITY_CTRL_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1A50)
+#define PEX_DBG_CTRL_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1A60)
+#define PEX_DBG_STATUS_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1A64)
+
+#define PXLCSR_NEG_LNK_GEN_OFFS 16 /* Negotiated Link GEN */
+#define PXLCSR_NEG_LNK_GEN_MASK (0xf << PXLCSR_NEG_LNK_GEN_OFFS)
+#define PXLCSR_NEG_LNK_GEN_1_1 (0x1 << PXLCSR_NEG_LNK_GEN_OFFS)
+#define PXLCSR_NEG_LNK_GEN_2_0 (0x2 << PXLCSR_NEG_LNK_GEN_OFFS)
+
+#define PEX_CFG_ADDR_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x18F8)
+#define PEX_CFG_DATA_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x18FC)
+#define PEX_CAUSE_REG(if) ((MV_PEX_IF_REGS_BASE(if)) + 0x1900)
+
+#define PEX_CAPABILITY_REG 0x60
+#define PEX_DEV_CAPABILITY_REG 0x64
+#define PEX_DEV_CTRL_STAT_REG 0x68
+#define PEX_LINK_CAPABILITY_REG 0x6C
+#define PEX_LINK_CTRL_STAT_REG 0x70
+#define PEX_LINK_CTRL_STAT_2_REG 0x90
+
+#endif /* __BOARD_ENV_SPEC */
--- /dev/null
+/*
+ * Copyright (C) Marvell International Ltd. and its affiliates
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+
+#include "high_speed_env_spec.h"
+#include "board_env_spec.h"
+
+#define SERDES_VERION "2.1.5"
+#define ENDED_OK "High speed PHY - Ended Successfully\n"
+
+static const u8 serdes_cfg[][SERDES_LAST_UNIT] = BIN_SERDES_CFG;
+
+extern MV_BIN_SERDES_CFG *serdes_info_tbl[];
+
+extern u8 rd78460gp_twsi_dev[];
+extern u8 db88f78xx0rev2_twsi_dev[];
+
+u32 pex_cfg_read(u32 pex_if, u32 bus, u32 dev, u32 func, u32 offs);
+int pex_local_bus_num_set(u32 pex_if, u32 bus_num);
+int pex_local_dev_num_set(u32 pex_if, u32 dev_num);
+
+#define MV_BOARD_PEX_MODULE_ADDR 0x23
+#define MV_BOARD_PEX_MODULE_ID 1
+#define MV_BOARD_ETM_MODULE_ID 2
+
+#define PEX_MODULE_DETECT 1
+#define ETM_MODULE_DETECT 2
+
+#define PEX_MODE_GET(satr) ((satr & 0x6) >> 1)
+#define PEX_CAPABILITY_GET(satr) (satr & 1)
+#define MV_PEX_UNIT_TO_IF(pex_unit) ((pex_unit < 3) ? (pex_unit * 4) : 9)
+
+/* Static parametes */
+static int config_module;
+static int switch_module;
+
+/* Local function */
+static u32 board_id_get(void)
+{
+#if defined(CONFIG_DB_88F78X60)
+ return DB_88F78XX0_BP_ID;
+#elif defined(CONFIG_RD_88F78460_SERVER)
+ return RD_78460_SERVER_ID;
+#elif defined(CONFIG_RD_78460_SERVER_REV2)
+ return RD_78460_SERVER_REV2_ID;
+#elif defined(CONFIG_DB_78X60_PCAC)
+ return DB_78X60_PCAC_ID;
+#elif defined(CONFIG_DB_88F78X60_REV2)
+ return DB_88F78XX0_BP_REV2_ID;
+#elif defined(CONFIG_RD_78460_NAS)
+ return RD_78460_NAS_ID;
+#elif defined(CONFIG_DB_78X60_AMC)
+ return DB_78X60_AMC_ID;
+#elif defined(CONFIG_DB_78X60_PCAC_REV2)
+ return DB_78X60_PCAC_REV2_ID;
+#elif defined(CONFIG_DB_784MP_GP)
+ return DB_784MP_GP_ID;
+#elif defined(CONFIG_RD_78460_CUSTOMER)
+ return RD_78460_CUSTOMER_ID;
+#else
+ /*
+ * Return 0 here for custom board as this should not be used
+ * for custom boards.
+ */
+ return 0;
+#endif
+}
+
+static u8 board_sat_r_get(u8 dev_num, u8 reg)
+{
+ u8 data;
+ u8 *dev;
+ u32 board_id = board_id_get();
+ int ret;
+
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+ switch (board_id) {
+ case DB_784MP_GP_ID:
+ dev = rd78460gp_twsi_dev;
+
+ break;
+ case DB_88F78XX0_BP_ID:
+ case DB_88F78XX0_BP_REV2_ID:
+ dev = db88f78xx0rev2_twsi_dev;
+ break;
+
+ case DB_78X60_PCAC_ID:
+ case FPGA_88F78XX0_ID:
+ case DB_78X60_PCAC_REV2_ID:
+ case RD_78460_SERVER_REV2_ID:
+ default:
+ return 0;
+ }
+
+ /* Read MPP module ID */
+ ret = i2c_read(dev[dev_num], 0, 1, (u8 *)&data, 1);
+ if (ret)
+ return MV_ERROR;
+
+ return data;
+}
+
+static int board_modules_scan(void)
+{
+ u8 val;
+ u32 board_id = board_id_get();
+ int ret;
+
+ /* Perform scan only for DB board */
+ if ((board_id == DB_88F78XX0_BP_ID) ||
+ (board_id == DB_88F78XX0_BP_REV2_ID)) {
+ /* reset modules flags */
+ config_module = 0;
+
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+ /* SERDES module (only PEX model is supported now) */
+ ret = i2c_read(MV_BOARD_PEX_MODULE_ADDR, 0, 1, (u8 *)&val, 1);
+ if (ret)
+ return MV_ERROR;
+
+ if (val == MV_BOARD_PEX_MODULE_ID)
+ config_module = PEX_MODULE_DETECT;
+ if (val == MV_BOARD_ETM_MODULE_ID)
+ config_module = ETM_MODULE_DETECT;
+ } else if (board_id == RD_78460_NAS_ID) {
+ switch_module = 0;
+ if ((reg_read(GPP_DATA_IN_REG(2)) & MV_GPP66) == 0x0)
+ switch_module = 1;
+ }
+
+ return MV_OK;
+}
+
+u32 pex_max_unit_get(void)
+{
+ /*
+ * TODO:
+ * Right now only MV78460 is supported. Other SoC's might need
+ * a different value here.
+ */
+ return MV_PEX_MAX_UNIT;
+}
+
+u32 pex_max_if_get(void)
+{
+ /*
+ * TODO:
+ * Right now only MV78460 is supported. Other SoC's might need
+ * a different value here.
+ */
+ return MV_PEX_MAX_IF;
+}
+
+u8 board_cpu_freq_get(void)
+{
+ u32 sar;
+ u32 sar_msb;
+
+ sar = reg_read(MPP_SAMPLE_AT_RESET(0));
+ sar_msb = reg_read(MPP_SAMPLE_AT_RESET(1));
+ return ((sar_msb & 0x100000) >> 17) | ((sar & 0xe00000) >> 21);
+}
+
+__weak MV_BIN_SERDES_CFG *board_serdes_cfg_get(u8 pex_mode)
+{
+ u32 board_id;
+ u32 serdes_cfg_val = 0; /* default */
+
+ board_id = board_id_get();
+
+ switch (board_id) {
+ case DB_784MP_GP_ID:
+ serdes_cfg_val = 0;
+ break;
+ }
+
+ return &serdes_info_tbl[board_id - BOARD_ID_BASE][serdes_cfg_val];
+}
+
+u16 ctrl_model_get(void)
+{
+ /* Right now only MV78460 supported */
+ return MV_78460_DEV_ID;
+}
+
+u32 get_line_cfg(u32 line_num, MV_BIN_SERDES_CFG *info)
+{
+ if (line_num < 8)
+ return (info->line0_7 >> (line_num << 2)) & 0xF;
+ else
+ return (info->line8_15 >> ((line_num - 8) << 2)) & 0xF;
+}
+
+int serdes_phy_config(void)
+{
+ int status = MV_OK;
+ u32 line_cfg;
+ u8 line_num;
+ /* addr/value for each line @ every setup step */
+ u32 addr[16][11], val[16][11];
+ u8 pex_unit, pex_line_num;
+ u8 sgmii_port = 0;
+ u32 tmp;
+ u32 in_direct;
+ u8 max_serdes_lines;
+ MV_BIN_SERDES_CFG *info;
+ u8 satr11;
+ u8 sata_port;
+ u8 freq;
+ u8 device_rev;
+ u32 rx_high_imp_mode;
+ u16 ctrl_mode;
+ u32 board_id = board_id_get();
+ u32 pex_if;
+ u32 pex_if_num;
+
+ /*
+ * TODO:
+ * Right now we only support the MV78460 with 16 serdes lines
+ */
+ max_serdes_lines = 16;
+ if (max_serdes_lines == 0)
+ return MV_OK;
+
+ switch (board_id) {
+ case DB_78X60_AMC_ID:
+ case DB_78X60_PCAC_REV2_ID:
+ case RD_78460_CUSTOMER_ID:
+ case RD_78460_SERVER_ID:
+ case RD_78460_SERVER_REV2_ID:
+ case DB_78X60_PCAC_ID:
+ satr11 = (0x1 << 1) | 1;
+ break;
+ case FPGA_88F78XX0_ID:
+ case RD_78460_NAS_ID:
+ satr11 = (0x0 << 1) | 1;
+ break;
+ case DB_88F78XX0_BP_REV2_ID:
+ case DB_784MP_GP_ID:
+ case DB_88F78XX0_BP_ID:
+ satr11 = board_sat_r_get(1, 1);
+ if ((u8) MV_ERROR == (u8) satr11)
+ return MV_ERROR;
+ break;
+ }
+
+ board_modules_scan();
+ memset(addr, 0, sizeof(addr));
+ memset(val, 0, sizeof(val));
+
+ /* Check if DRAM is already initialized */
+ if (reg_read(REG_BOOTROM_ROUTINE_ADDR) &
+ (1 << REG_BOOTROM_ROUTINE_DRAM_INIT_OFFS)) {
+ DEBUG_INIT_S("High speed PHY - Version: ");
+ DEBUG_INIT_S(SERDES_VERION);
+ DEBUG_INIT_S(" - 2nd boot - Skip\n");
+ return MV_OK;
+ }
+ DEBUG_INIT_S("High speed PHY - Version: ");
+ DEBUG_INIT_S(SERDES_VERION);
+ DEBUG_INIT_S(" (COM-PHY-V20)\n");
+
+ /*
+ * AVS : disable AVS for frequency less than 1333
+ */
+ freq = board_cpu_freq_get();
+ device_rev = mv_ctrl_rev_get();
+
+ if (device_rev == 2) { /* for B0 only */
+ u32 cpu_avs;
+ u8 fabric_freq;
+ cpu_avs = reg_read(CPU_AVS_CONTROL2_REG);
+ DEBUG_RD_REG(CPU_AVS_CONTROL2_REG, cpu_avs);
+ cpu_avs &= ~(1 << 9);
+
+ if ((0x4 == freq) || (0xB == freq)) {
+ u32 tmp2;
+
+ tmp2 = reg_read(CPU_AVS_CONTROL0_REG);
+ DEBUG_RD_REG(CPU_AVS_CONTROL0_REG, tmp2);
+ /* cpu upper limit = 1.1V cpu lower limit = 0.9125V */
+ tmp2 |= 0x0FF;
+ reg_write(CPU_AVS_CONTROL0_REG, tmp2);
+ DEBUG_WR_REG(CPU_AVS_CONTROL0_REG, tmp2);
+ cpu_avs |= (1 << 9); /* cpu avs enable */
+ cpu_avs |= (1 << 18); /* AvsAvddDetEn enable */
+ fabric_freq = (reg_read(MPP_SAMPLE_AT_RESET(0)) &
+ SAR0_FABRIC_FREQ_MASK) >> SAR0_FABRIC_FREQ_OFFSET;
+ if ((0xB == freq) && (5 == fabric_freq)) {
+ u32 core_avs;
+
+ core_avs = reg_read(CORE_AVS_CONTROL_0REG);
+ DEBUG_RD_REG(CORE_AVS_CONTROL_0REG, core_avs);
+
+ /*
+ * Set core lower limit = 0.9V &
+ * core upper limit = 0.9125V
+ */
+ core_avs &= ~(0xff);
+ core_avs |= 0x0E;
+ reg_write(CORE_AVS_CONTROL_0REG, core_avs);
+ DEBUG_WR_REG(CORE_AVS_CONTROL_0REG, core_avs);
+
+ core_avs = reg_read(CORE_AVS_CONTROL_2REG);
+ DEBUG_RD_REG(CORE_AVS_CONTROL_2REG, core_avs);
+ core_avs |= (1 << 9); /* core AVS enable */
+ reg_write(CORE_AVS_CONTROL_2REG, core_avs);
+ DEBUG_WR_REG(CORE_AVS_CONTROL_2REG, core_avs);
+
+ tmp2 = reg_read(GENERAL_PURPOSE_RESERVED0_REG);
+ DEBUG_RD_REG(GENERAL_PURPOSE_RESERVED0_REG,
+ tmp2);
+ tmp2 |= 0x1; /* AvsCoreAvddDetEn enable */
+ reg_write(GENERAL_PURPOSE_RESERVED0_REG, tmp2);
+ DEBUG_WR_REG(GENERAL_PURPOSE_RESERVED0_REG,
+ tmp2);
+ }
+ }
+ reg_write(CPU_AVS_CONTROL2_REG, cpu_avs);
+ DEBUG_WR_REG(CPU_AVS_CONTROL2_REG, cpu_avs);
+ }
+
+ info = board_serdes_cfg_get(PEX_MODE_GET(satr11));
+ DEBUG_INIT_FULL_S("info->line0_7= 0x");
+ DEBUG_INIT_FULL_D(info->line0_7, 8);
+ DEBUG_INIT_FULL_S(" info->line8_15= 0x");
+ DEBUG_INIT_FULL_D(info->line8_15, 8);
+ DEBUG_INIT_FULL_S("\n");
+
+ if (info == NULL) {
+ DEBUG_INIT_S("Hight speed PHY Error #1\n");
+ return MV_ERROR;
+ }
+
+ if (config_module & ETM_MODULE_DETECT) { /* step 0.9 ETM */
+ DEBUG_INIT_FULL_S("ETM module detect Step 0.9:\n");
+ reg_write(SERDES_LINE_MUX_REG_0_7, 0x11111111);
+ DEBUG_WR_REG(SERDES_LINE_MUX_REG_0_7, 0x11111111);
+ info->pex_mode[1] = PEX_BUS_DISABLED; /* pex unit 1 is configure for ETM */
+ mdelay(100);
+ reg_write(PEX_PHY_ACCESS_REG(1), (0x002 << 16) | 0xf44d); /* SETM0 - start calibration */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(1), (0x002 << 16) | 0xf44d); /* SETM0 - start calibration */
+ reg_write(PEX_PHY_ACCESS_REG(1), (0x302 << 16) | 0xf44d); /* SETM1 - start calibration */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(1), (0x302 << 16) | 0xf44d); /* SETM1 - start calibration */
+ reg_write(PEX_PHY_ACCESS_REG(1), (0x001 << 16) | 0xf801); /* SETM0 - SATA mode & 25MHz ref clk */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(1), (0x001 << 16) | 0xf801); /* SETM0 - SATA mode & 25MHz ref clk */
+ reg_write(PEX_PHY_ACCESS_REG(1), (0x301 << 16) | 0xf801); /* SETM1 - SATA mode & 25MHz ref clk */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(1), (0x301 << 16) | 0xf801); /* SETM1 - SATA mode & 25MHz ref clk */
+ reg_write(PEX_PHY_ACCESS_REG(1), (0x011 << 16) | 0x0BFF); /* SETM0 - G3 full swing AMP */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(1), (0x011 << 16) | 0x0BFF); /* SETM0 - G3 full swing AMP */
+ reg_write(PEX_PHY_ACCESS_REG(1), (0x311 << 16) | 0x0BFF); /* SETM1 - G3 full swing AMP */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(1), (0x311 << 16) | 0x0BFF); /* SETM1 - G3 full swing AMP */
+ reg_write(PEX_PHY_ACCESS_REG(1), (0x023 << 16) | 0x0800); /* SETM0 - 40 data bit width */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(1), (0x023 << 16) | 0x0800); /* SETM0 - 40 data bit width */
+ reg_write(PEX_PHY_ACCESS_REG(1), (0x323 << 16) | 0x0800); /* SETM1 - 40 data bit width */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(1), (0x323 << 16) | 0x0800); /* SETM1 - 40 data bit width */
+ reg_write(PEX_PHY_ACCESS_REG(1), (0x046 << 16) | 0x0400); /* lane0(serdes4) */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(1), (0x046 << 16) | 0x0400); /* lane0(serdes4) */
+ reg_write(PEX_PHY_ACCESS_REG(1), (0x346 << 16) | 0x0400); /* lane3(serdes7) */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(1), (0x346 << 16) | 0x0400); /* lane3(serdes7) */
+ }
+
+ /* STEP -1 [PEX-Only] First phase of PEX-PIPE Configuration: */
+ DEBUG_INIT_FULL_S("Step 1: First phase of PEX-PIPE Configuration\n");
+ for (pex_unit = 0; pex_unit < pex_max_unit_get(); pex_unit++) {
+ if (info->pex_mode[pex_unit] == PEX_BUS_DISABLED)
+ continue;
+
+ /* 1. GLOB_CLK_CTRL Reset and Clock Control */
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit), (0xC1 << 16) | 0x25);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit), (0xC1 << 16) | 0x25);
+
+ /* 2. GLOB_TEST_CTRL Test Mode Control */
+ if (info->pex_mode[pex_unit] == PEX_BUS_MODE_X4) {
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit),
+ (0xC2 << 16) | 0x200);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit),
+ (0xC2 << 16) | 0x200);
+ }
+
+ /* 3. GLOB_CLK_SRC_LO Clock Source Low */
+ if (info->pex_mode[pex_unit] == PEX_BUS_MODE_X1) {
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit),
+ (0xC3 << 16) | 0x0F);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit),
+ (0xC3 << 16) | 0x0F);
+ }
+
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit), (0xC5 << 16) | 0x11F);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit),
+ (0xC5 << 16) | 0x11F);
+ }
+
+ /*
+ * 2 Configure the desire PIN_PHY_GEN and do power down to the PU_PLL,
+ * PU_RX,PU_TX. (bits[12:5])
+ */
+ DEBUG_INIT_FULL_S("Step 2: Configure the desire PIN_PHY_GEN\n");
+ for (line_num = 0; line_num < max_serdes_lines; line_num++) {
+ line_cfg = get_line_cfg(line_num, info);
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_UNCONNECTED])
+ continue;
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_PEX])
+ continue;
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SATA]) {
+ switch (line_num) {
+ case 4:
+ case 6:
+ sata_port = 0;
+ break;
+ case 5:
+ sata_port = 1;
+ break;
+ default:
+ DEBUG_INIT_C
+ ("SATA port error for serdes line: ",
+ line_num, 2);
+ return MV_ERROR;
+ }
+ tmp = reg_read(SATA_LP_PHY_EXT_CTRL_REG(sata_port));
+ DEBUG_RD_REG(SATA_LP_PHY_EXT_CTRL_REG(sata_port), tmp);
+ tmp &= ~((0x1ff << 5) | 0x7);
+ tmp |= ((info->bus_speed & (1 << line_num)) != 0) ?
+ (0x11 << 5) : 0x0;
+
+ reg_write(SATA_LP_PHY_EXT_CTRL_REG(sata_port), tmp);
+ DEBUG_WR_REG(SATA_LP_PHY_EXT_CTRL_REG(sata_port), tmp);
+ }
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_QSGMII]) {
+ /*
+ * 4) Configure the desire PIN_PHY_GEN and do power
+ * down to the PU_PLL,PU_RX,PU_TX. (bits[12:5])
+ */
+ tmp = reg_read(SGMII_SERDES_CFG_REG(0));
+ DEBUG_RD_REG(SGMII_SERDES_CFG_REG(0), tmp);
+ tmp &= ~((0x1ff << 5) | 0x7);
+ tmp |= 0x660;
+ reg_write(SGMII_SERDES_CFG_REG(0), tmp);
+ DEBUG_WR_REG(SGMII_SERDES_CFG_REG(0), tmp);
+ continue;
+ }
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII0])
+ sgmii_port = 0;
+ else if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII1])
+ sgmii_port = 1;
+ else if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII2])
+ sgmii_port = 2;
+ else if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII3])
+ sgmii_port = 3;
+ else
+ continue;
+
+ tmp = reg_read(SGMII_SERDES_CFG_REG(sgmii_port));
+ DEBUG_RD_REG(SGMII_SERDES_CFG_REG(sgmii_port), tmp);
+ tmp &= ~((0x1ff << 5) | 0x7);
+ tmp |= (((info->bus_speed & (1 << line_num)) != 0) ?
+ (0x88 << 5) : (0x66 << 5));
+ reg_write(SGMII_SERDES_CFG_REG(sgmii_port), tmp);
+ DEBUG_WR_REG(SGMII_SERDES_CFG_REG(sgmii_port), tmp);
+ }
+
+ /* Step 3 - QSGMII enable */
+ DEBUG_INIT_FULL_S("Step 3 QSGMII enable\n");
+ for (line_num = 0; line_num < max_serdes_lines; line_num++) {
+ line_cfg = get_line_cfg(line_num, info);
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_QSGMII]) {
+ /* QSGMII Active bit set to true */
+ tmp = reg_read(QSGMII_CONTROL_1_REG);
+ DEBUG_RD_REG(QSGMII_CONTROL_1_REG, tmp);
+ tmp |= (1 << 30);
+#ifdef ERRATA_GL_6572255
+ tmp |= (1 << 27);
+#endif
+ reg_write(QSGMII_CONTROL_1_REG, tmp);
+ DEBUG_WR_REG(QSGMII_CONTROL_1_REG, tmp);
+ }
+ }
+
+ /* Step 4 - configure SERDES MUXes */
+ DEBUG_INIT_FULL_S("Step 4: Configure SERDES MUXes\n");
+ if (config_module & ETM_MODULE_DETECT) {
+ reg_write(SERDES_LINE_MUX_REG_0_7, 0x40041111);
+ DEBUG_WR_REG(SERDES_LINE_MUX_REG_0_7, 0x40041111);
+ } else {
+ reg_write(SERDES_LINE_MUX_REG_0_7, info->line0_7);
+ DEBUG_WR_REG(SERDES_LINE_MUX_REG_0_7, info->line0_7);
+ }
+ reg_write(SERDES_LINE_MUX_REG_8_15, info->line8_15);
+ DEBUG_WR_REG(SERDES_LINE_MUX_REG_8_15, info->line8_15);
+
+ /* Step 5: Activate the RX High Impedance Mode */
+ DEBUG_INIT_FULL_S("Step 5: Activate the RX High Impedance Mode\n");
+ rx_high_imp_mode = 0x8080;
+ if (device_rev == 2) /* for B0 only */
+ rx_high_imp_mode |= 4;
+
+ for (line_num = 0; line_num < max_serdes_lines; line_num++) {
+ /* for each serdes lane */
+ DEBUG_INIT_FULL_S("SERDES ");
+ DEBUG_INIT_FULL_D_10(line_num, 2);
+ line_cfg = get_line_cfg(line_num, info);
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_UNCONNECTED]) {
+ DEBUG_INIT_FULL_S(" unconnected ***\n");
+ continue;
+ }
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_PEX]) {
+ pex_unit = line_num >> 2;
+ pex_line_num = line_num % 4;
+ DEBUG_INIT_FULL_S(" - PEX unit ");
+ DEBUG_INIT_FULL_D_10(pex_unit, 1);
+ DEBUG_INIT_FULL_S(" line= ");
+ DEBUG_INIT_FULL_D_10(pex_line_num, 1);
+ DEBUG_INIT_FULL_S("\n");
+
+ /* Needed for PEX_PHY_ACCESS_REG macro */
+ if ((line_num > 7) &&
+ (info->pex_mode[3] == PEX_BUS_MODE_X8))
+ /* lines 8 - 15 are belong to PEX3 in x8 mode */
+ pex_unit = 3;
+
+ if (info->pex_mode[pex_unit] == PEX_BUS_DISABLED)
+ continue;
+
+ /*
+ * 8) Activate the RX High Impedance Mode field
+ * (bit [2]) in register /PCIe_USB Control (Each MAC
+ * contain different Access to reach its
+ * Serdes-Regfile).
+ * [PEX-Only] Set bit[12]: The analog part latches idle
+ * if PU_TX = 1 and PU_PLL =1.
+ */
+
+ /* Termination enable */
+ if (info->pex_mode[pex_unit] == PEX_BUS_MODE_X1) {
+ in_direct = (0x48 << 16) | (pex_line_num << 24) |
+ 0x1000 | rx_high_imp_mode; /* x1 */
+ } else if ((info->pex_mode[pex_unit] ==
+ PEX_BUS_MODE_X4) && (pex_line_num == 0))
+ in_direct = (0x48 << 16) | (pex_line_num << 24) |
+ 0x1000 | (rx_high_imp_mode & 0xff); /* x4 */
+ else
+ in_direct = 0;
+
+ if (in_direct) {
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit),
+ in_direct);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit),
+ in_direct);
+ }
+
+ continue;
+ }
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SATA]) {
+ /*
+ * port 0 for serdes lines 4,6, and port 1 for
+ * serdes lines 5
+ */
+ sata_port = line_num & 1;
+ DEBUG_INIT_FULL_S(" - SATA port ");
+ DEBUG_INIT_FULL_D_10(sata_port, 2);
+ DEBUG_INIT_FULL_S("\n");
+ reg_write(SATA_COMPHY_CTRL_REG(sata_port),
+ rx_high_imp_mode);
+ DEBUG_WR_REG(SATA_COMPHY_CTRL_REG(sata_port),
+ rx_high_imp_mode);
+ continue;
+ }
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_QSGMII]) {
+ DEBUG_INIT_FULL_S(" - QSGMII\n");
+ reg_write(SGMII_COMPHY_CTRL_REG(0), rx_high_imp_mode);
+ DEBUG_WR_REG(SGMII_COMPHY_CTRL_REG(0),
+ rx_high_imp_mode);
+ continue;
+ }
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII0])
+ sgmii_port = 0;
+ else if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII1])
+ sgmii_port = 1;
+ else if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII2])
+ sgmii_port = 2;
+ else if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII3])
+ sgmii_port = 3;
+ else
+ continue;
+ DEBUG_INIT_FULL_S(" - SGMII port ");
+ DEBUG_INIT_FULL_D_10(sgmii_port, 2);
+ DEBUG_INIT_FULL_S("\n");
+ reg_write(SGMII_COMPHY_CTRL_REG(sgmii_port), rx_high_imp_mode);
+ DEBUG_WR_REG(SGMII_COMPHY_CTRL_REG(sgmii_port),
+ rx_high_imp_mode);
+ } /* for each serdes lane */
+
+ /* Step 6 [PEX-Only] PEX-Main configuration (X4 or X1): */
+ DEBUG_INIT_FULL_S("Step 6: [PEX-Only] PEX-Main configuration (X4 or X1)\n");
+ tmp = reg_read(SOC_CTRL_REG);
+ DEBUG_RD_REG(SOC_CTRL_REG, tmp);
+ tmp &= 0x200;
+ if (info->pex_mode[0] == PEX_BUS_MODE_X1)
+ tmp |= PCIE0_QUADX1_EN;
+ if (info->pex_mode[1] == PEX_BUS_MODE_X1)
+ tmp |= PCIE1_QUADX1_EN;
+ if (((reg_read(MPP_SAMPLE_AT_RESET(0)) & PEX_CLK_100MHZ_MASK) >>
+ PEX_CLK_100MHZ_OFFSET) == 0x1)
+ tmp |= (PCIE0_CLK_OUT_EN_MASK | PCIE1_CLK_OUT_EN_MASK);
+
+ reg_write(SOC_CTRL_REG, tmp);
+ DEBUG_WR_REG(SOC_CTRL_REG, tmp);
+
+ /* 6.2 PCI Express Link Capabilities */
+ DEBUG_INIT_FULL_S("Step 6.2: [PEX-Only] PCI Express Link Capabilities\n");
+
+ for (line_num = 0; line_num < max_serdes_lines; line_num++) {
+ line_cfg = get_line_cfg(line_num, info);
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_PEX]) {
+ /*
+ * PCI Express Control
+ * 0xX1A00 [0]:
+ * 0x0 X4-Link.
+ * 0x1 X1-Link
+ */
+ pex_unit = line_num >> 2;
+ pex_if = MV_SERDES_NUM_TO_PEX_NUM(line_num);
+ if (info->pex_mode[pex_unit] == PEX_BUS_DISABLED)
+ continue;
+
+ /* set Common Clock Configuration */
+ tmp = reg_read(PEX_LINK_CTRL_STATUS_REG(pex_if));
+ DEBUG_RD_REG(PEX_LINK_CTRL_STATUS_REG(pex_if), tmp);
+ tmp |= (1 << 6);
+ reg_write(PEX_LINK_CTRL_STATUS_REG(pex_if), tmp);
+ DEBUG_WR_REG(PEX_LINK_CTRL_STATUS_REG(pex_if), tmp);
+
+ tmp = reg_read(PEX_LINK_CAPABILITIES_REG(pex_if));
+ DEBUG_RD_REG(PEX_LINK_CAPABILITIES_REG(pex_if), tmp);
+ tmp &= ~(0x3FF);
+ if (info->pex_mode[pex_unit] == PEX_BUS_MODE_X1)
+ tmp |= (0x1 << 4);
+ if (info->pex_mode[pex_unit] == PEX_BUS_MODE_X4)
+ tmp |= (0x4 << 4);
+ if (0 == PEX_CAPABILITY_GET(satr11))
+ tmp |= 0x1;
+ else
+ tmp |= 0x2;
+ DEBUG_INIT_FULL_S("Step 6.2: PEX ");
+ DEBUG_INIT_FULL_D(pex_if, 1);
+ DEBUG_INIT_FULL_C(" set GEN", (tmp & 3), 1);
+ reg_write(PEX_LINK_CAPABILITIES_REG(pex_if), tmp);
+ DEBUG_WR_REG(PEX_LINK_CAPABILITIES_REG(pex_if), tmp);
+
+ /*
+ * If pex is X4, no need to pass thru the other
+ * 3X1 serdes lines
+ */
+ if (info->pex_mode[pex_unit] == PEX_BUS_MODE_X4)
+ line_num += 3;
+ }
+ }
+
+ /*
+ * Step 7 [PEX-X4 Only] To create PEX-Link that contain 4-lanes you
+ * need to config the register SOC_Misc/General Purpose2
+ * (Address= 182F8)
+ */
+ DEBUG_INIT_FULL_S("Step 7: [PEX-X4 Only] To create PEX-Link\n");
+ tmp = reg_read(GEN_PURP_RES_2_REG);
+ DEBUG_RD_REG(GEN_PURP_RES_2_REG, tmp);
+
+ tmp &= 0xFFFF0000;
+ if (info->pex_mode[0] == PEX_BUS_MODE_X4)
+ tmp |= 0x0000000F;
+
+ if (info->pex_mode[1] == PEX_BUS_MODE_X4)
+ tmp |= 0x000000F0;
+
+ if (info->pex_mode[2] == PEX_BUS_MODE_X4)
+ tmp |= 0x00000F00;
+
+ if (info->pex_mode[3] == PEX_BUS_MODE_X4)
+ tmp |= 0x0000F000;
+
+ reg_write(GEN_PURP_RES_2_REG, tmp);
+ DEBUG_WR_REG(GEN_PURP_RES_2_REG, tmp);
+
+ /* Steps 8 , 9 ,10 - use prepared REG addresses and values */
+ DEBUG_INIT_FULL_S("Steps 7,8,9,10 and 11\n");
+
+ /* Prepare PHY parameters for each step according to MUX selection */
+ for (line_num = 0; line_num < max_serdes_lines; line_num++) {
+ /* for each serdes lane */
+
+ line_cfg = get_line_cfg(line_num, info);
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_UNCONNECTED])
+ continue;
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_PEX]) {
+ pex_unit = line_num >> 2;
+ pex_line_num = line_num % 4;
+
+ if (info->pex_mode[pex_unit] == PEX_BUS_DISABLED)
+ continue;
+ /*
+ * 8) Configure the desire PHY_MODE (bits [7:5])
+ * and REF_FREF_SEL (bits[4:0]) in the register Power
+ * and PLL Control (Each MAC contain different Access
+ * to reach its Serdes-Regfile).
+ */
+ if (((info->pex_mode[pex_unit] == PEX_BUS_MODE_X4) &&
+ (0 == pex_line_num))
+ || ((info->pex_mode[pex_unit] == PEX_BUS_MODE_X1))) {
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit),
+ (0x01 << 16) | (pex_line_num << 24) |
+ 0xFC60);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit),
+ (0x01 << 16) | (pex_line_num << 24)
+ | 0xFC60);
+ /*
+ * Step 8.1: [PEX-Only] Configure Max PLL Rate
+ * (bit 8 in KVCO Calibration Control and
+ * bits[10:9] in
+ */
+ /* Use Maximum PLL Rate(Bit 8) */
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit),
+ (0x02 << 16) | (1 << 31) |
+ (pex_line_num << 24)); /* read command */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit),
+ (0x02 << 16) | (1 << 31) |
+ (pex_line_num << 24));
+ tmp = reg_read(PEX_PHY_ACCESS_REG(pex_unit));
+ DEBUG_RD_REG(PEX_PHY_ACCESS_REG(pex_unit), tmp);
+ tmp &= ~(1 << 31);
+ tmp |= (1 << 8);
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit), tmp);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit), tmp);
+
+ /* Use Maximum PLL Rate(Bits [10:9]) */
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit),
+ (0x81 << 16) | (1 << 31) |
+ (pex_line_num << 24)); /* read command */
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit),
+ (0x81 << 16) | (1 << 31) |
+ (pex_line_num << 24));
+ tmp = reg_read(PEX_PHY_ACCESS_REG(pex_unit));
+ DEBUG_RD_REG(PEX_PHY_ACCESS_REG(pex_unit), tmp);
+ tmp &= ~(1 << 31);
+ tmp |= (3 << 9);
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit), tmp);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit), tmp);
+ }
+
+ continue;
+ }
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SATA]) {
+ /*
+ * Port 0 for serdes lines 4,6, and port 1 for serdes
+ * lines 5
+ */
+ sata_port = line_num & 1;
+
+ /*
+ * 8) Configure the desire PHY_MODE (bits [7:5]) and
+ * REF_FREF_SEL (bits[4:0]) in the register Power
+ * and PLL Control (Each MAC contain different Access
+ * to reach its Serdes-Regfile).
+ */
+ reg_write(SATA_PWR_PLL_CTRL_REG(sata_port), 0xF801);
+ DEBUG_WR_REG(SATA_PWR_PLL_CTRL_REG(sata_port), 0xF801);
+
+ /* 9) Configure the desire SEL_BITS */
+ reg_write(SATA_DIG_LP_ENA_REG(sata_port), 0x400);
+ DEBUG_WR_REG(SATA_DIG_LP_ENA_REG(sata_port), 0x400);
+
+ /* 10) Configure the desire REFCLK_SEL */
+
+ reg_write(SATA_REF_CLK_SEL_REG(sata_port), 0x400);
+ DEBUG_WR_REG(SATA_REF_CLK_SEL_REG(sata_port), 0x400);
+
+ /* 11) Power up to the PU_PLL,PU_RX,PU_TX. */
+ tmp = reg_read(SATA_LP_PHY_EXT_CTRL_REG(sata_port));
+ DEBUG_RD_REG(SATA_LP_PHY_EXT_CTRL_REG(sata_port), tmp);
+ tmp |= 7;
+ reg_write(SATA_LP_PHY_EXT_CTRL_REG(sata_port), tmp);
+ DEBUG_WR_REG(SATA_LP_PHY_EXT_CTRL_REG(sata_port), tmp);
+
+ continue;
+ }
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_QSGMII]) {
+ /*
+ * 8) Configure the desire PHY_MODE (bits [7:5])
+ * and REF_FREF_SEL (bits[4:0]) in the register
+ */
+ reg_write(SGMII_PWR_PLL_CTRL_REG(0), 0xF881);
+ DEBUG_WR_REG(SGMII_PWR_PLL_CTRL_REG(0), 0xF881);
+
+ /*
+ * 9) Configure the desire SEL_BITS (bits [11:0]
+ * in register
+ */
+ reg_write(SGMII_DIG_LP_ENA_REG(0), 0x400);
+ DEBUG_WR_REG(SGMII_DIG_LP_ENA_REG(0), 0x400);
+
+ /*
+ * 10) Configure the desire REFCLK_SEL (bit [10])
+ * in register
+ */
+ reg_write(SGMII_REF_CLK_SEL_REG(0), 0x400);
+ DEBUG_WR_REG(SGMII_REF_CLK_SEL_REG(0), 0x400);
+
+ /* 11) Power up to the PU_PLL,PU_RX,PU_TX. */
+ tmp = reg_read(SGMII_SERDES_CFG_REG(0));
+ DEBUG_RD_REG(SGMII_SERDES_CFG_REG(0), tmp);
+ tmp |= 7;
+ reg_write(SGMII_SERDES_CFG_REG(0), tmp);
+ DEBUG_WR_REG(SGMII_SERDES_CFG_REG(0), tmp);
+ continue;
+ }
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII0])
+ sgmii_port = 0;
+ else if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII1])
+ sgmii_port = 1;
+ else if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII2])
+ sgmii_port = 2;
+ else if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SGMII3])
+ sgmii_port = 3;
+ else
+ continue;
+
+ /*
+ * 8) Configure the desire PHY_MODE (bits [7:5]) and
+ * REF_FREF_SEL (bits[4:0]) in the register
+ */
+ reg_write(SGMII_PWR_PLL_CTRL_REG(sgmii_port), 0xF881);
+ DEBUG_WR_REG(SGMII_PWR_PLL_CTRL_REG(sgmii_port), 0xF881);
+
+ /* 9) Configure the desire SEL_BITS (bits [11:0] in register */
+ reg_write(SGMII_DIG_LP_ENA_REG(sgmii_port), 0);
+ DEBUG_WR_REG(SGMII_DIG_LP_ENA_REG(sgmii_port), 0);
+
+ /* 10) Configure the desire REFCLK_SEL (bit [10]) in register */
+ reg_write(SGMII_REF_CLK_SEL_REG(sgmii_port), 0x400);
+ DEBUG_WR_REG(SGMII_REF_CLK_SEL_REG(sgmii_port), 0x400);
+
+ /* 11) Power up to the PU_PLL,PU_RX,PU_TX. */
+ tmp = reg_read(SGMII_SERDES_CFG_REG(sgmii_port));
+ DEBUG_RD_REG(SGMII_SERDES_CFG_REG(sgmii_port), tmp);
+ tmp |= 7;
+ reg_write(SGMII_SERDES_CFG_REG(sgmii_port), tmp);
+ DEBUG_WR_REG(SGMII_SERDES_CFG_REG(sgmii_port), tmp);
+
+ } /* for each serdes lane */
+
+ /* Step 12 [PEX-Only] Last phase of PEX-PIPE Configuration */
+ DEBUG_INIT_FULL_S("Steps 12: [PEX-Only] Last phase of PEX-PIPE Configuration\n");
+ for (line_num = 0; line_num < max_serdes_lines; line_num++) {
+ /* for each serdes lane */
+
+ line_cfg = get_line_cfg(line_num, info);
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_UNCONNECTED])
+ continue;
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_PEX]) {
+ pex_unit = line_num >> 2;
+ pex_line_num = line_num % 4;
+ if (0 == pex_line_num) {
+ reg_write(PEX_PHY_ACCESS_REG(pex_unit),
+ (0xC1 << 16) | 0x24);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG(pex_unit),
+ (0xC1 << 16) | 0x24);
+ }
+ }
+ }
+
+ /*--------------------------------------------------------------*/
+ /* Step 13: Wait 15ms before checking results */
+ DEBUG_INIT_FULL_S("Steps 13: Wait 15ms before checking results");
+ mdelay(15);
+ tmp = 20;
+ while (tmp) {
+ status = MV_OK;
+ for (line_num = 0; line_num < max_serdes_lines; line_num++) {
+ u32 tmp;
+ line_cfg = get_line_cfg(line_num, info);
+ if (line_cfg ==
+ serdes_cfg[line_num][SERDES_UNIT_UNCONNECTED])
+ continue;
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_PEX])
+ continue;
+
+ if (line_cfg == serdes_cfg[line_num][SERDES_UNIT_SATA]) {
+ /*
+ * Port 0 for serdes lines 4,6, and port 1
+ * for serdes lines 5
+ */
+ sata_port = line_num & 1;
+
+ tmp =
+ reg_read(SATA_LP_PHY_EXT_STAT_REG
+ (sata_port));
+ DEBUG_RD_REG(SATA_LP_PHY_EXT_STAT_REG
+ (sata_port), tmp);
+ if ((tmp & 0x7) != 0x7)
+ status = MV_ERROR;
+ continue;
+ }
+
+ if (line_cfg ==
+ serdes_cfg[line_num][SERDES_UNIT_QSGMII]) {
+ tmp = reg_read(SGMII_SERDES_STAT_REG(0));
+ DEBUG_RD_REG(SGMII_SERDES_STAT_REG(0), tmp);
+ if ((tmp & 0x7) != 0x7)
+ status = MV_ERROR;
+ continue;
+ }
+
+ if (line_cfg ==
+ serdes_cfg[line_num][SERDES_UNIT_SGMII0])
+ sgmii_port = 0;
+ else if (line_cfg ==
+ serdes_cfg[line_num][SERDES_UNIT_SGMII1])
+ sgmii_port = 1;
+ else if (line_cfg ==
+ serdes_cfg[line_num][SERDES_UNIT_SGMII2])
+ sgmii_port = 2;
+ else if (line_cfg ==
+ serdes_cfg[line_num][SERDES_UNIT_SGMII3])
+ sgmii_port = 3;
+ else
+ continue;
+
+ tmp = reg_read(SGMII_SERDES_STAT_REG(sgmii_port));
+ DEBUG_RD_REG(SGMII_SERDES_STAT_REG(sgmii_port), tmp);
+ if ((tmp & 0x7) != 0x7)
+ status = MV_ERROR;
+ }
+
+ if (status == MV_OK)
+ break;
+ mdelay(5);
+ tmp--;
+ }
+
+ /*
+ * Step14 [PEX-Only] In order to configure RC/EP mode please write
+ * to register 0x0060 bits
+ */
+ DEBUG_INIT_FULL_S("Steps 14: [PEX-Only] In order to configure\n");
+ for (pex_unit = 0; pex_unit < pex_max_unit_get(); pex_unit++) {
+ if (info->pex_mode[pex_unit] == PEX_BUS_DISABLED)
+ continue;
+ tmp =
+ reg_read(PEX_CAPABILITIES_REG(MV_PEX_UNIT_TO_IF(pex_unit)));
+ DEBUG_RD_REG(PEX_CAPABILITIES_REG(MV_PEX_UNIT_TO_IF(pex_unit)),
+ tmp);
+ tmp &= ~(0xf << 20);
+ if (info->pex_type == MV_PEX_ROOT_COMPLEX)
+ tmp |= (0x4 << 20);
+ else
+ tmp |= (0x1 << 20);
+ reg_write(PEX_CAPABILITIES_REG(MV_PEX_UNIT_TO_IF(pex_unit)),
+ tmp);
+ DEBUG_WR_REG(PEX_CAPABILITIES_REG(MV_PEX_UNIT_TO_IF(pex_unit)),
+ tmp);
+ }
+
+ /*
+ * Step 15 [PEX-Only] Only for EP mode set to Zero bits 19 and 16 of
+ * register 0x1a60
+ */
+ DEBUG_INIT_FULL_S("Steps 15: [PEX-Only] In order to configure\n");
+ for (pex_unit = 0; pex_unit < pex_max_unit_get(); pex_unit++) {
+ if (info->pex_mode[pex_unit] == PEX_BUS_DISABLED)
+ continue;
+ if (info->pex_type == MV_PEX_END_POINT) {
+ tmp =
+ reg_read(PEX_DBG_CTRL_REG
+ (MV_PEX_UNIT_TO_IF(pex_unit)));
+ DEBUG_RD_REG(PEX_DBG_CTRL_REG
+ (MV_PEX_UNIT_TO_IF(pex_unit)), tmp);
+ tmp &= 0xfff6ffff;
+ reg_write(PEX_DBG_CTRL_REG(MV_PEX_UNIT_TO_IF(pex_unit)),
+ tmp);
+ DEBUG_WR_REG(PEX_DBG_CTRL_REG
+ (MV_PEX_UNIT_TO_IF(pex_unit)), tmp);
+ }
+ }
+
+ if (info->serdes_m_phy_change) {
+ MV_SERDES_CHANGE_M_PHY *serdes_m_phy_change;
+ u32 bus_speed;
+ for (line_num = 0; line_num < max_serdes_lines; line_num++) {
+ line_cfg = get_line_cfg(line_num, info);
+ if (line_cfg ==
+ serdes_cfg[line_num][SERDES_UNIT_UNCONNECTED])
+ continue;
+ serdes_m_phy_change = info->serdes_m_phy_change;
+ bus_speed = info->bus_speed & (1 << line_num);
+ while (serdes_m_phy_change->type !=
+ SERDES_UNIT_UNCONNECTED) {
+ switch (serdes_m_phy_change->type) {
+ case SERDES_UNIT_PEX:
+ if (line_cfg != SERDES_UNIT_PEX)
+ break;
+ pex_unit = line_num >> 2;
+ pex_line_num = line_num % 4;
+ if (info->pex_mode[pex_unit] ==
+ PEX_BUS_DISABLED)
+ break;
+ if ((info->pex_mode[pex_unit] ==
+ PEX_BUS_MODE_X4) && pex_line_num)
+ break;
+
+ if (bus_speed) {
+ reg_write(PEX_PHY_ACCESS_REG
+ (pex_unit),
+ (pex_line_num << 24) |
+ serdes_m_phy_change->val_hi_speed);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG
+ (pex_unit),
+ (pex_line_num <<
+ 24) |
+ serdes_m_phy_change->val_hi_speed);
+ } else {
+ reg_write(PEX_PHY_ACCESS_REG
+ (pex_unit),
+ (pex_line_num << 24) |
+ serdes_m_phy_change->val_low_speed);
+ DEBUG_WR_REG(PEX_PHY_ACCESS_REG
+ (pex_unit),
+ (pex_line_num <<
+ 24) |
+ serdes_m_phy_change->val_low_speed);
+ }
+ break;
+ case SERDES_UNIT_SATA:
+ if (line_cfg != SERDES_UNIT_SATA)
+ break;
+ /*
+ * Port 0 for serdes lines 4,6, and
+ * port 1 for serdes lines 5
+ */
+ sata_port = line_num & 1;
+ if (bus_speed) {
+ reg_write(SATA_BASE_REG
+ (sata_port) |
+ serdes_m_phy_change->reg_hi_speed,
+ serdes_m_phy_change->val_hi_speed);
+ DEBUG_WR_REG(SATA_BASE_REG
+ (sata_port) |
+ serdes_m_phy_change->reg_hi_speed,
+ serdes_m_phy_change->val_hi_speed);
+ } else {
+ reg_write(SATA_BASE_REG
+ (sata_port) |
+ serdes_m_phy_change->reg_low_speed,
+ serdes_m_phy_change->val_low_speed);
+ DEBUG_WR_REG(SATA_BASE_REG
+ (sata_port) |
+ serdes_m_phy_change->reg_low_speed,
+ serdes_m_phy_change->val_low_speed);
+ }
+ break;
+ case SERDES_UNIT_SGMII0:
+ case SERDES_UNIT_SGMII1:
+ case SERDES_UNIT_SGMII2:
+ case SERDES_UNIT_SGMII3:
+ if (line_cfg == serdes_cfg[line_num]
+ [SERDES_UNIT_SGMII0])
+ sgmii_port = 0;
+ else if (line_cfg ==
+ serdes_cfg[line_num]
+ [SERDES_UNIT_SGMII1])
+ sgmii_port = 1;
+ else if (line_cfg ==
+ serdes_cfg[line_num]
+ [SERDES_UNIT_SGMII2])
+ sgmii_port = 2;
+ else if (line_cfg ==
+ serdes_cfg[line_num]
+ [SERDES_UNIT_SGMII3])
+ sgmii_port = 3;
+ else
+ break;
+ if (bus_speed) {
+ reg_write(MV_ETH_REGS_BASE
+ (sgmii_port) |
+ serdes_m_phy_change->reg_hi_speed,
+ serdes_m_phy_change->val_hi_speed);
+ DEBUG_WR_REG(MV_ETH_REGS_BASE
+ (sgmii_port) |
+ serdes_m_phy_change->reg_hi_speed,
+ serdes_m_phy_change->val_hi_speed);
+ } else {
+ reg_write(MV_ETH_REGS_BASE
+ (sgmii_port) |
+ serdes_m_phy_change->reg_low_speed,
+ serdes_m_phy_change->val_low_speed);
+ DEBUG_WR_REG(MV_ETH_REGS_BASE
+ (sgmii_port) |
+ serdes_m_phy_change->reg_low_speed,
+ serdes_m_phy_change->val_low_speed);
+ }
+ break;
+ case SERDES_UNIT_QSGMII:
+ if (line_cfg != SERDES_UNIT_QSGMII)
+ break;
+ if (bus_speed) {
+ reg_write
+ (serdes_m_phy_change->reg_hi_speed,
+ serdes_m_phy_change->val_hi_speed);
+ DEBUG_WR_REG
+ (serdes_m_phy_change->reg_hi_speed,
+ serdes_m_phy_change->val_hi_speed);
+ } else {
+ reg_write
+ (serdes_m_phy_change->reg_low_speed,
+ serdes_m_phy_change->val_low_speed);
+ DEBUG_WR_REG
+ (serdes_m_phy_change->reg_low_speed,
+ serdes_m_phy_change->val_low_speed);
+ }
+ break;
+ default:
+ break;
+ }
+ serdes_m_phy_change++;
+ }
+ }
+ }
+
+ /* Step 16 [PEX-Only] Training Enable */
+ DEBUG_INIT_FULL_S("Steps 16: [PEX-Only] Training Enable");
+ tmp = reg_read(SOC_CTRL_REG);
+ DEBUG_RD_REG(SOC_CTRL_REG, tmp);
+ tmp &= ~(0x0F);
+ for (pex_unit = 0; pex_unit < pex_max_unit_get(); pex_unit++) {
+ reg_write(PEX_CAUSE_REG(pex_unit), 0);
+ DEBUG_WR_REG(PEX_CAUSE_REG(pex_unit), 0);
+ if (info->pex_mode[pex_unit] != PEX_BUS_DISABLED)
+ tmp |= (0x1 << pex_unit);
+ }
+ reg_write(SOC_CTRL_REG, tmp);
+ DEBUG_WR_REG(SOC_CTRL_REG, tmp);
+
+ /* Step 17: Speed change to target speed and width */
+ {
+ u32 tmp_reg, tmp_pex_reg;
+ u32 addr;
+ u32 first_busno, next_busno;
+ u32 max_link_width = 0;
+ u32 neg_link_width = 0;
+ pex_if_num = pex_max_if_get();
+ mdelay(150);
+ DEBUG_INIT_FULL_C("step 17: max_if= 0x", pex_if_num, 1);
+ next_busno = 0;
+ for (pex_if = 0; pex_if < pex_if_num; pex_if++) {
+ line_num = (pex_if <= 8) ? pex_if : 12;
+ line_cfg = get_line_cfg(line_num, info);
+ if (line_cfg != serdes_cfg[line_num][SERDES_UNIT_PEX])
+ continue;
+ pex_unit = (pex_if < 9) ? (pex_if >> 2) : 3;
+ DEBUG_INIT_FULL_S("step 17: PEX");
+ DEBUG_INIT_FULL_D(pex_if, 1);
+ DEBUG_INIT_FULL_C(" pex_unit= ", pex_unit, 1);
+
+ if (info->pex_mode[pex_unit] == PEX_BUS_DISABLED) {
+ DEBUG_INIT_FULL_C("PEX disabled interface ",
+ pex_if, 1);
+ if (pex_if < 8)
+ pex_if += 3;
+ continue;
+ }
+ first_busno = next_busno;
+ if ((info->pex_type == MV_PEX_END_POINT) &&
+ (0 == pex_if)) {
+ if ((pex_if < 8) && (info->pex_mode[pex_unit] ==
+ PEX_BUS_MODE_X4))
+ pex_if += 3;
+ continue;
+ }
+
+ tmp = reg_read(PEX_DBG_STATUS_REG(pex_if));
+ DEBUG_RD_REG(PEX_DBG_STATUS_REG(pex_if), tmp);
+ if ((tmp & 0x7f) == 0x7e) {
+ next_busno++;
+ tmp = reg_read(PEX_LINK_CAPABILITIES_REG(pex_if));
+ max_link_width = tmp;
+ DEBUG_RD_REG((PEX_LINK_CAPABILITIES_REG
+ (pex_if)), tmp);
+ max_link_width = ((max_link_width >> 4) & 0x3F);
+ neg_link_width =
+ reg_read(PEX_LINK_CTRL_STATUS_REG(pex_if));
+ DEBUG_RD_REG((PEX_LINK_CTRL_STATUS_REG(pex_if)),
+ neg_link_width);
+ neg_link_width = ((neg_link_width >> 20) & 0x3F);
+ if (max_link_width > neg_link_width) {
+ tmp &= ~(0x3F << 4);
+ tmp |= (neg_link_width << 4);
+ reg_write(PEX_LINK_CAPABILITIES_REG
+ (pex_if), tmp);
+ DEBUG_WR_REG((PEX_LINK_CAPABILITIES_REG
+ (pex_if)), tmp);
+ mdelay(1); /* wait 1ms before reading capability for speed */
+ DEBUG_INIT_S("PEX");
+ DEBUG_INIT_D(pex_if, 1);
+ DEBUG_INIT_C(": change width to X",
+ neg_link_width, 1);
+ }
+ tmp_pex_reg =
+ reg_read((PEX_CFG_DIRECT_ACCESS
+ (pex_if,
+ PEX_LINK_CAPABILITY_REG)));
+ DEBUG_RD_REG((PEX_CFG_DIRECT_ACCESS
+ (pex_if,
+ PEX_LINK_CAPABILITY_REG)),
+ tmp_pex_reg);
+ tmp_pex_reg &= (0xF);
+ if (tmp_pex_reg == 0x2) {
+ tmp_reg =
+ (reg_read
+ (PEX_CFG_DIRECT_ACCESS
+ (pex_if,
+ PEX_LINK_CTRL_STAT_REG)) &
+ 0xF0000) >> 16;
+ DEBUG_RD_REG(PEX_CFG_DIRECT_ACCESS
+ (pex_if,
+ PEX_LINK_CTRL_STAT_REG),
+ tmp_pex_reg);
+ /* check if the link established is GEN1 */
+ if (tmp_reg == 0x1) {
+ pex_local_bus_num_set(pex_if,
+ first_busno);
+ pex_local_dev_num_set(pex_if,
+ 1);
+
+ DEBUG_INIT_FULL_S("** Link is Gen1, check the EP capability\n");
+ /* link is Gen1, check the EP capability */
+ addr =
+ pex_cfg_read(pex_if,
+ first_busno, 0,
+ 0,
+ 0x34) & 0xFF;
+ DEBUG_INIT_FULL_C("pex_cfg_read: return addr=0x%x",
+ addr, 4);
+ if (addr == 0xff) {
+ DEBUG_INIT_FULL_C("pex_cfg_read: return 0xff -->PEX (%d): Detected No Link.",
+ pex_if, 1);
+ continue;
+ }
+ while ((pex_cfg_read
+ (pex_if, first_busno, 0,
+ 0,
+ addr) & 0xFF) !=
+ 0x10) {
+ addr =
+ (pex_cfg_read
+ (pex_if,
+ first_busno, 0, 0,
+ addr) & 0xFF00) >>
+ 8;
+ }
+ if ((pex_cfg_read
+ (pex_if, first_busno, 0, 0,
+ addr + 0xC) & 0xF) >=
+ 0x2) {
+ tmp =
+ reg_read
+ (PEX_LINK_CTRL_STATUS2_REG
+ (pex_if));
+ DEBUG_RD_REG
+ (PEX_LINK_CTRL_STATUS2_REG
+ (pex_if), tmp);
+ tmp &= ~(0x1 | 1 << 1);
+ tmp |= (1 << 1);
+ reg_write
+ (PEX_LINK_CTRL_STATUS2_REG
+ (pex_if), tmp);
+ DEBUG_WR_REG
+ (PEX_LINK_CTRL_STATUS2_REG
+ (pex_if), tmp);
+
+ tmp =
+ reg_read
+ (PEX_CTRL_REG
+ (pex_if));
+ DEBUG_RD_REG
+ (PEX_CTRL_REG
+ (pex_if), tmp);
+ tmp |= (1 << 10);
+ reg_write(PEX_CTRL_REG
+ (pex_if),
+ tmp);
+ DEBUG_WR_REG
+ (PEX_CTRL_REG
+ (pex_if), tmp);
+ mdelay(10); /* We need to wait 10ms before reading the PEX_DBG_STATUS_REG in order not to read the status of the former state */
+ DEBUG_INIT_FULL_S
+ ("Gen2 client!\n");
+ } else {
+ DEBUG_INIT_FULL_S
+ ("GEN1 client!\n");
+ }
+ }
+ }
+ } else {
+ DEBUG_INIT_FULL_S("PEX");
+ DEBUG_INIT_FULL_D(pex_if, 1);
+ DEBUG_INIT_FULL_S(" : Detected No Link. Status Reg(0x");
+ DEBUG_INIT_FULL_D(PEX_DBG_STATUS_REG(pex_if),
+ 8);
+ DEBUG_INIT_FULL_C(") = 0x", tmp, 8);
+ }
+
+ if ((pex_if < 8) &&
+ (info->pex_mode[pex_unit] == PEX_BUS_MODE_X4))
+ pex_if += 3;
+ }
+ }
+
+ /* Step 18: update pex DEVICE ID */
+ {
+ u32 devId;
+ pex_if_num = pex_max_if_get();
+ ctrl_mode = ctrl_model_get();
+ for (pex_if = 0; pex_if < pex_if_num; pex_if++) {
+ pex_unit = (pex_if < 9) ? (pex_if >> 2) : 3;
+ if (info->pex_mode[pex_unit] == PEX_BUS_DISABLED) {
+ if ((pex_if < 8) &&
+ (info->pex_mode[pex_unit] == PEX_BUS_MODE_X4))
+ pex_if += 3;
+ continue;
+ }
+
+ devId = reg_read(PEX_CFG_DIRECT_ACCESS(
+ pex_if, PEX_DEVICE_AND_VENDOR_ID));
+ devId &= 0xFFFF;
+ devId |= ((ctrl_mode << 16) & 0xffff0000);
+ DEBUG_INIT_S("Update Device ID PEX");
+ DEBUG_INIT_D(pex_if, 1);
+ DEBUG_INIT_D(devId, 8);
+ DEBUG_INIT_S("\n");
+ reg_write(PEX_CFG_DIRECT_ACCESS
+ (pex_if, PEX_DEVICE_AND_VENDOR_ID), devId);
+ if ((pex_if < 8) &&
+ (info->pex_mode[pex_unit] == PEX_BUS_MODE_X4))
+ pex_if += 3;
+ }
+ DEBUG_INIT_S("Update PEX Device ID 0x");
+ DEBUG_INIT_D(ctrl_mode, 4);
+ DEBUG_INIT_S("0\n");
+ }
+ tmp = reg_read(PEX_DBG_STATUS_REG(0));
+ DEBUG_RD_REG(PEX_DBG_STATUS_REG(0), tmp);
+
+ DEBUG_INIT_S(ENDED_OK);
+ return MV_OK;
+}
+
+/* PEX configuration space read write */
+
+/*
+ * pex_cfg_read - Read from configuration space
+ *
+ * DESCRIPTION:
+ * This function performs a 32 bit read from PEX configuration space.
+ * It supports both type 0 and type 1 of Configuration Transactions
+ * (local and over bridge). In order to read from local bus segment, use
+ * bus number retrieved from mvPexLocalBusNumGet(). Other bus numbers
+ * will result configuration transaction of type 1 (over bridge).
+ *
+ * INPUT:
+ * pex_if - PEX interface number.
+ * bus - PEX segment bus number.
+ * dev - PEX device number.
+ * func - Function number.
+ * offss - Register offset.
+ *
+ * OUTPUT:
+ * None.
+ *
+ * RETURN:
+ * 32bit register data, 0xffffffff on error
+ *
+ */
+u32 pex_cfg_read(u32 pex_if, u32 bus, u32 dev, u32 func, u32 offs)
+{
+ u32 pex_data = 0;
+ u32 local_dev, local_bus;
+ u32 val;
+
+ if (pex_if >= MV_PEX_MAX_IF)
+ return 0xFFFFFFFF;
+
+ if (dev >= MAX_PEX_DEVICES) {
+ DEBUG_INIT_C("pex_cfg_read: ERR. device number illigal ", dev,
+ 1);
+ return 0xFFFFFFFF;
+ }
+
+ if (func >= MAX_PEX_FUNCS) {
+ DEBUG_INIT_C("pex_cfg_read: ERR. function num illigal ", func,
+ 1);
+ return 0xFFFFFFFF;
+ }
+
+ if (bus >= MAX_PEX_BUSSES) {
+ DEBUG_INIT_C("pex_cfg_read: ERR. bus number illigal ", bus, 1);
+ return MV_ERROR;
+ }
+ val = reg_read(PEX_STATUS_REG(pex_if));
+
+ local_dev =
+ ((val & PXSR_PEX_DEV_NUM_MASK) >> PXSR_PEX_DEV_NUM_OFFS);
+ local_bus =
+ ((val & PXSR_PEX_BUS_NUM_MASK) >> PXSR_PEX_BUS_NUM_OFFS);
+
+ /* Speed up the process. In case on no link, return MV_ERROR */
+ if ((dev != local_dev) || (bus != local_bus)) {
+ pex_data = reg_read(PEX_STATUS_REG(pex_if));
+
+ if ((pex_data & PXSR_DL_DOWN))
+ return MV_ERROR;
+ }
+
+ /*
+ * In PCI Express we have only one device number
+ * and this number is the first number we encounter else that the
+ * local_dev spec pex define return on config read/write on any device
+ */
+ if (bus == local_bus) {
+ if (local_dev == 0) {
+ /*
+ * If local dev is 0 then the first number we encounter
+ * after 0 is 1
+ */
+ if ((dev != 1) && (dev != local_dev))
+ return MV_ERROR;
+ } else {
+ /*
+ * If local dev is not 0 then the first number we
+ * encounter is 0
+ */
+ if ((dev != 0) && (dev != local_dev))
+ return MV_ERROR;
+ }
+ }
+
+ /* Creating PEX address to be passed */
+ pex_data = (bus << PXCAR_BUS_NUM_OFFS);
+ pex_data |= (dev << PXCAR_DEVICE_NUM_OFFS);
+ pex_data |= (func << PXCAR_FUNC_NUM_OFFS);
+ pex_data |= (offs & PXCAR_REG_NUM_MASK); /* lgacy register space */
+ /* extended register space */
+ pex_data |= (((offs & PXCAR_REAL_EXT_REG_NUM_MASK) >>
+ PXCAR_REAL_EXT_REG_NUM_OFFS) << PXCAR_EXT_REG_NUM_OFFS);
+
+ pex_data |= PXCAR_CONFIG_EN;
+
+ /* Write the address to the PEX configuration address register */
+ reg_write(PEX_CFG_ADDR_REG(pex_if), pex_data);
+
+ /*
+ * In order to let the PEX controller absorbed the address of the read
+ * transaction we perform a validity check that the address was written
+ */
+ if (pex_data != reg_read(PEX_CFG_ADDR_REG(pex_if)))
+ return MV_ERROR;
+
+ /* cleaning Master Abort */
+ reg_bit_set(PEX_CFG_DIRECT_ACCESS(pex_if, PEX_STATUS_AND_COMMAND),
+ PXSAC_MABORT);
+ /* Read the Data returned in the PEX Data register */
+ pex_data = reg_read(PEX_CFG_DATA_REG(pex_if));
+
+ DEBUG_INIT_FULL_C(" --> ", pex_data, 4);
+
+ return pex_data;
+}
+
+/*
+ * pex_local_bus_num_set - Set PEX interface local bus number.
+ *
+ * DESCRIPTION:
+ * This function sets given PEX interface its local bus number.
+ * Note: In case the PEX interface is PEX-X, the information is read-only.
+ *
+ * INPUT:
+ * pex_if - PEX interface number.
+ * bus_num - Bus number.
+ *
+ * OUTPUT:
+ * None.
+ *
+ * RETURN:
+ * MV_NOT_ALLOWED in case PEX interface is PEX-X.
+ * MV_BAD_PARAM on bad parameters ,
+ * otherwise MV_OK
+ *
+ */
+int pex_local_bus_num_set(u32 pex_if, u32 bus_num)
+{
+ u32 val;
+
+ if (bus_num >= MAX_PEX_BUSSES) {
+ DEBUG_INIT_C("pex_local_bus_num_set: ERR. bus number illigal %d\n",
+ bus_num, 4);
+ return MV_ERROR;
+ }
+
+ val = reg_read(PEX_STATUS_REG(pex_if));
+ val &= ~PXSR_PEX_BUS_NUM_MASK;
+ val |= (bus_num << PXSR_PEX_BUS_NUM_OFFS) & PXSR_PEX_BUS_NUM_MASK;
+ reg_write(PEX_STATUS_REG(pex_if), val);
+
+ return MV_OK;
+}
+
+/*
+ * pex_local_dev_num_set - Set PEX interface local device number.
+ *
+ * DESCRIPTION:
+ * This function sets given PEX interface its local device number.
+ * Note: In case the PEX interface is PEX-X, the information is read-only.
+ *
+ * INPUT:
+ * pex_if - PEX interface number.
+ * dev_num - Device number.
+ *
+ * OUTPUT:
+ * None.
+ *
+ * RETURN:
+ * MV_NOT_ALLOWED in case PEX interface is PEX-X.
+ * MV_BAD_PARAM on bad parameters ,
+ * otherwise MV_OK
+ *
+ */
+int pex_local_dev_num_set(u32 pex_if, u32 dev_num)
+{
+ u32 val;
+
+ if (pex_if >= MV_PEX_MAX_IF)
+ return MV_BAD_PARAM;
+
+ val = reg_read(PEX_STATUS_REG(pex_if));
+ val &= ~PXSR_PEX_DEV_NUM_MASK;
+ val |= (dev_num << PXSR_PEX_DEV_NUM_OFFS) & PXSR_PEX_DEV_NUM_MASK;
+ reg_write(PEX_STATUS_REG(pex_if), val);
+
+ return MV_OK;
+}
--- /dev/null
+/*
+ * Copyright (C) Marvell International Ltd. and its affiliates
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+
+#include "high_speed_env_spec.h"
+
+MV_SERDES_CHANGE_M_PHY serdes_change_m_phy[] = {
+ /* SERDES TYPE, Low REG OFFS, Low REG VALUE, Hi REG OFS, Hi REG VALUE */
+ {
+ /* PEX: Change of Slew Rate port0 */
+ SERDES_UNIT_PEX, 0x0,
+ (0x0F << 16) | 0x2a21, 0x0, (0x0F << 16) | 0x2a21
+ }, {
+ /* PEX: Change PLL BW port0 */
+ SERDES_UNIT_PEX, 0x0,
+ (0x4F << 16) | 0x6219, 0x0, (0x4F << 16) | 0x6219
+ }, {
+ /* SATA: Slew rate change port 0 */
+ SERDES_UNIT_SATA, 0x0083C, 0x8a31, 0x0083C, 0x8a31
+ }, {
+ /* SATA: Slew rate change port 0 */
+ SERDES_UNIT_SATA, 0x00834, 0xc928, 0x00834, 0xc928
+ }, {
+ /* SATA: Slew rate change port 0 */
+ SERDES_UNIT_SATA, 0x00838, 0x30f0, 0x00838, 0x30f0
+ }, {
+ /* SATA: Slew rate change port 0 */
+ SERDES_UNIT_SATA, 0x00840, 0x30f5, 0x00840, 0x30f5
+ }, {
+ /* SGMII: FFE setting Port0 */
+ SERDES_UNIT_SGMII0, 0x00E18, 0x989F, 0x00E18, 0x989F
+ }, {
+ /* SGMII: SELMUP and SELMUF Port0 */
+ SERDES_UNIT_SGMII0, 0x00E38, 0x10FA, 0x00E38, 0x10FA
+ }, {
+ /* SGMII: Amplitude new setting gen2 Port3 */
+ SERDES_UNIT_SGMII0, 0x00E34, 0xC968, 0x00E34, 0xC66C
+ }, {
+ /* QSGMII: Amplitude and slew rate change */
+ SERDES_UNIT_QSGMII, 0x72E34, 0xaa58, 0x72E34, 0xaa58
+ }, {
+ /* QSGMII: SELMUP and SELMUF */
+ SERDES_UNIT_QSGMII, 0x72e38, 0x10aF, 0x72e38, 0x10aF
+ }, {
+ /* QSGMII: 0x72e18 */
+ SERDES_UNIT_QSGMII, 0x72e18, 0x98AC, 0x72e18, 0x98AC
+ }, {
+ /* Null terminated */
+ SERDES_UNIT_UNCONNECTED, 0, 0
+ }
+};
+
+MV_BIN_SERDES_CFG db88f78xx0_serdes_cfg[] = {
+ /* Z1B */
+ {MV_PEX_ROOT_COMPLEX, 0x32221111, 0x11111111,
+ {PEX_BUS_MODE_X1, PEX_BUS_DISABLED, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x0030, serdes_change_m_phy}, /* Default */
+ {MV_PEX_ROOT_COMPLEX, 0x31211111, 0x11111111,
+ {PEX_BUS_MODE_X1, PEX_BUS_MODE_X1, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x0030, serdes_change_m_phy}, /* PEX module */
+ /* Z1A */
+ {MV_PEX_ROOT_COMPLEX, 0x32220000, 0x00000000,
+ {PEX_BUS_DISABLED, PEX_BUS_DISABLED, PEX_BUS_DISABLED,
+ PEX_BUS_DISABLED}, 0x0030, serdes_change_m_phy}, /* Default - Z1A */
+ {MV_PEX_ROOT_COMPLEX, 0x31210000, 0x00000000,
+ {PEX_BUS_DISABLED, PEX_BUS_MODE_X1, PEX_BUS_DISABLED, PEX_BUS_DISABLED},
+ 0x0030, serdes_change_m_phy} /* PEX module - Z1A */
+};
+
+MV_BIN_SERDES_CFG db88f78xx0rev2_serdes_cfg[] = {
+ /* A0 */
+ {MV_PEX_ROOT_COMPLEX, 0x33221111, 0x11111111,
+ {PEX_BUS_MODE_X1, PEX_BUS_DISABLED, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x0030, serdes_change_m_phy}, /* Default: No Pex module, PEX0 x1, disabled */
+ {MV_PEX_ROOT_COMPLEX, 0x33211111, 0x11111111,
+ {PEX_BUS_MODE_X1, PEX_BUS_MODE_X1, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x0030, serdes_change_m_phy}, /* Pex module, PEX0 x1, PEX1 x1 */
+ {MV_PEX_ROOT_COMPLEX, 0x33221111, 0x11111111,
+ {PEX_BUS_MODE_X4, PEX_BUS_DISABLED, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x0030, serdes_change_m_phy}, /* no Pex module, PEX0 x4, PEX1 disabled */
+ {MV_PEX_ROOT_COMPLEX, 0x33211111, 0x11111111,
+ {PEX_BUS_MODE_X4, PEX_BUS_MODE_X1, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x0030, serdes_change_m_phy}, /* Pex module, PEX0 x4, PEX1 x1 */
+ {MV_PEX_ROOT_COMPLEX, 0x11111111, 0x11111111,
+ {PEX_BUS_MODE_X1, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x0030, serdes_change_m_phy}, /* Pex module, PEX0 x1, PEX1 x4 */
+ {MV_PEX_ROOT_COMPLEX, 0x11111111, 0x11111111,
+ {PEX_BUS_MODE_X4, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x0030, serdes_change_m_phy}, /* Pex module, PEX0 x4, PEX1 x4 */
+};
+
+MV_BIN_SERDES_CFG rd78460nas_serdes_cfg[] = {
+ {MV_PEX_ROOT_COMPLEX, 0x00223001, 0x11111111,
+ {PEX_BUS_MODE_X1, PEX_BUS_DISABLED, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x0030, serdes_change_m_phy}, /* Default */
+ {MV_PEX_ROOT_COMPLEX, 0x33320201, 0x11111111,
+ {PEX_BUS_MODE_X1, PEX_BUS_DISABLED, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x00f4, serdes_change_m_phy}, /* Switch module */
+};
+
+MV_BIN_SERDES_CFG rd78460_serdes_cfg[] = {
+ {MV_PEX_ROOT_COMPLEX, 0x22321111, 0x00000000,
+ {PEX_BUS_MODE_X4, PEX_BUS_DISABLED, PEX_BUS_DISABLED, PEX_BUS_DISABLED},
+ 0x0010, serdes_change_m_phy}, /* CPU0 */
+ {MV_PEX_ROOT_COMPLEX, 0x00321111, 0x00000000,
+ {PEX_BUS_MODE_X4, PEX_BUS_DISABLED, PEX_BUS_DISABLED, PEX_BUS_DISABLED},
+ 0x0010, serdes_change_m_phy} /* CPU1-3 */
+};
+
+MV_BIN_SERDES_CFG rd78460server_rev2_serdes_cfg[] = {
+ {MV_PEX_ROOT_COMPLEX, 0x00321111, 0x00000000,
+ {PEX_BUS_MODE_X4, PEX_BUS_DISABLED, PEX_BUS_DISABLED, PEX_BUS_DISABLED},
+ 0x0010, serdes_change_m_phy}, /* CPU0 */
+ {MV_PEX_ROOT_COMPLEX, 0x00321111, 0x00000000,
+ {PEX_BUS_MODE_X4, PEX_BUS_DISABLED, PEX_BUS_DISABLED, PEX_BUS_DISABLED},
+ 0x0010, serdes_change_m_phy} /* CPU1-3 */
+};
+
+MV_BIN_SERDES_CFG db78X60pcac_serdes_cfg[] = {
+ {MV_PEX_END_POINT, 0x22321111, 0x00000000,
+ {PEX_BUS_MODE_X4, PEX_BUS_DISABLED, PEX_BUS_DISABLED, PEX_BUS_DISABLED},
+ 0x0010, serdes_change_m_phy} /* Default */
+};
+
+MV_BIN_SERDES_CFG db78X60pcacrev2_serdes_cfg[] = {
+ {MV_PEX_END_POINT, 0x23321111, 0x00000000,
+ {PEX_BUS_MODE_X4, PEX_BUS_DISABLED, PEX_BUS_DISABLED, PEX_BUS_DISABLED},
+ 0x0010, serdes_change_m_phy} /* Default */
+};
+
+MV_BIN_SERDES_CFG fpga88f78xx0_serdes_cfg[] = {
+ {MV_PEX_ROOT_COMPLEX, 0x00000000, 0x00000000,
+ {PEX_BUS_DISABLED, PEX_BUS_DISABLED, PEX_BUS_DISABLED, PEX_BUS_DISABLED},
+ 0x0000, serdes_change_m_phy} /* No PEX in FPGA */
+};
+
+MV_BIN_SERDES_CFG db78X60amc_serdes_cfg[] = {
+ {MV_PEX_ROOT_COMPLEX, 0x33111111, 0x00010001,
+ {PEX_BUS_MODE_X4, PEX_BUS_MODE_X1, PEX_BUS_MODE_X1, PEX_BUS_MODE_X1},
+ 0x0030, serdes_change_m_phy} /* Default */
+};
+
+/*
+ * ARMADA-XP CUSTOMER BOARD
+ */
+MV_BIN_SERDES_CFG rd78460customer_serdes_cfg[] = {
+ {MV_PEX_ROOT_COMPLEX, 0x00223001, 0x11111111,
+ {PEX_BUS_MODE_X1, PEX_BUS_DISABLED, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x00000030, serdes_change_m_phy}, /* Default */
+ {MV_PEX_ROOT_COMPLEX, 0x33320201, 0x11111111,
+ {PEX_BUS_MODE_X1, PEX_BUS_DISABLED, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x00000030, serdes_change_m_phy}, /* Switch module */
+};
+
+MV_BIN_SERDES_CFG rd78460AXP_GP_serdes_cfg[] = {
+ {MV_PEX_ROOT_COMPLEX, 0x00223001, 0x11111111,
+ {PEX_BUS_MODE_X1, PEX_BUS_DISABLED, PEX_BUS_MODE_X4, PEX_BUS_MODE_X4},
+ 0x0030, serdes_change_m_phy} /* Default */
+};
+
+MV_BIN_SERDES_CFG *serdes_info_tbl[] = {
+ db88f78xx0_serdes_cfg,
+ rd78460_serdes_cfg,
+ db78X60pcac_serdes_cfg,
+ fpga88f78xx0_serdes_cfg,
+ db88f78xx0rev2_serdes_cfg,
+ rd78460nas_serdes_cfg,
+ db78X60amc_serdes_cfg,
+ db78X60pcacrev2_serdes_cfg,
+ rd78460server_rev2_serdes_cfg,
+ rd78460AXP_GP_serdes_cfg,
+ rd78460customer_serdes_cfg
+};
+
+u8 rd78460gp_twsi_dev[] = { 0x4C, 0x4D, 0x4E };
+u8 db88f78xx0rev2_twsi_dev[] = { 0x4C, 0x4D, 0x4E, 0x4F };
projects / u-boot.git / commitdiff