source "board/hisilicon/hikey960/Kconfig"
source "board/hisilicon/poplar/Kconfig"
source "board/isee/igep003x/Kconfig"
+source "board/myir/mys_6ulx/Kconfig"
source "board/spear/spear300/Kconfig"
source "board/spear/spear310/Kconfig"
source "board/spear/spear320/Kconfig"
dtb-$(CONFIG_MX6ULL) += \
imx6ull-14x14-evk.dtb \
imx6ull-colibri.dtb \
+ imx6ull-myir-mys-6ulx-eval.dtb \
imx6ull-phytec-segin-ff-rdk-emmc.dtb \
imx6ull-dart-6ul.dtb \
imx6ull-somlabs-visionsom.dtb \
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-myir-mys-6ulx.dtsi"
+#include "imx6ull-mys-6ulx-u-boot.dtsi"
+
+/ {
+ model = "MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND";
+ compatible = "myir,imx6ull-mys-6ulx-eval", "fsl,imx6ull";
+};
+
+&gpmi {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "MYiR MYS-6ULX Single Board Computer";
+ compatible = "fsl,imx6ull";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ reg_vdd_5v: regulator-vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reg_vdd_3v3: regulator-vdd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <®_vdd_5v>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ phy-supply = <®_vdd_3v3>;
+ status = "okay";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_vdd_3v3>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ keep-power-in-suspend;
+ vmmc-supply = <®_vdd_3v3>;
+};
+
+&iomuxc {
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
+ MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_CLE__RAWNAND_CLE 0x0b0b1
+ MX6UL_PAD_NAND_ALE__RAWNAND_ALE 0x0b0b1
+ MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B 0x0b0b1
+ MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B 0x0b000
+ MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B 0x0b0b1
+ MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B 0x0b0b1
+ MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B 0x0b0b1
+ MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00 0x0b0b1
+ MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01 0x0b0b1
+ MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02 0x0b0b1
+ MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03 0x0b0b1
+ MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04 0x0b0b1
+ MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05 0x0b0b1
+ MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06 0x0b0b1
+ MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07 0x0b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170b9
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170b9
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170b9
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+&pinctrl_uart1 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpmi {
+ u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
+};
+
+&usdhc1 {
+ u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
+};
+
+&usdhc2 {
+ u-boot,dm-spl;
+ u-boot,dm-pre-reloc;
+};
select MX6ULL
imply CMD_DM
+config TARGET_MYS_6ULX
+ bool "MYiR MYS-6ULX"
+ select MX6ULL
+ select DM
+ select DM_ETH
+ select DM_GPIO
+ select DM_I2C
+ select DM_MMC
+ select DM_SERIAL
+ select DM_THERMAL
+ select SUPPORT_SPL
+
config TARGET_NITROGEN6X
bool "nitrogen6x"
imply USB_ETHER_ASIX
--- /dev/null
+if TARGET_MYS_6ULX
+
+config SYS_BOARD
+ default "mys_6ulx"
+
+config SYS_VENDOR
+ default "myir"
+
+config SYS_CONFIG_NAME
+ default "mys_6ulx"
+
+endif
--- /dev/null
+MYS_6ULX BOARD
+M: Parthiban Nallathambi <parthiban@linumiz.com>
+S: Maintained
+F: arch/arm/dts/imx6ull-myir-mys-6ulx-nand.dts
+F: arch/arm/dts/imx6ull-myir-mys-6ulx.dtsi
+F: arch/arm/dts/imx6ull-mys-6ulx-u-boot.dtsi
+F: board/myir/mys_6ulx/
+F: configs/myir_mys_6ulx_defconfig
+F: include/configs/mys_6ulx.h
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y := mys_6ulx.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
--- /dev/null
+How to use U-Boot on MYiR MYS-6ULX Single Board Computer
+--------------------------------------------------------
+
+- Configure and build U-Boot for MYS-6ULX iMX6ULL:
+
+ $ make mrproper
+ $ make myir_mys_6ulx_defconfig
+ $ make
+
+ This will generate SPL and u-boot-dtb.img images.
+
+Boot from MMC/SD:
+- The SPL and u-boot-dtb.img images need to be flashed into the micro SD card:
+
+ $ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+ $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Boot mode settings:
+
+ Boot switch position: SW1 -> 0
+ SW2 -> 1
+ SW3 -> 0
+ SW4 -> 1
+
+Boot from NAND:
+- Boot the board using SD/MMC or Serial download and load the SPL into memory
+either from SD/MMC or TFTP.
+
+Default MTD layout is 512k(spl),1m(uboot),1m(uboot-dup),-(ubi)
+
+Flash SPL to NAND from SD/MMC,
+
+ $ ext4load mmc 0:2 $loadaddr SPL
+ $ nand erase.part spl
+ $ nandbcb init $loadaddr 0x0 $filesize
+
+Flash u-boot proper to NAND from SD/MMC,
+
+ $ ext4load mmc 0:2 $loadaddr u-boot-dtb.img
+ $ nand erase.part uboot
+ $ nand write $loadaddr uboot $filesize
+
+- Boot mode settings:
+
+ Boot switch position: SW1 -> 1
+ SW2 -> 0
+ SW3 -> 0
+ SW4 -> 1
+
+- Connect the Serial cable to UART0 and the PC for the console.
+
+- Reset the board using and U-Boot should boot from NAND.
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+#include <init.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc_imx.h>
+#include <linux/bitops.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+ return 0;
+}
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | \
+ PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart5_pads[] = {
+ MX6_PAD_UART5_TX_DATA__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_UART5_RX_DATA__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_GPIO1_IO09__UART5_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_GPIO1_IO08__UART5_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+ imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+}
+
+#ifdef CONFIG_FEC_MXC
+
+static int setup_fec(void)
+{
+ struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ int ret;
+
+ /*
+ * Use 50M anatop loopback REF_CLK1 for ENET1,
+ * clear gpr1[13], set gpr1[17].
+ */
+ clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+ IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+
+ ret = enable_fec_anatop_clock(0, ENET_50MHZ);
+ if (ret)
+ return ret;
+
+ enable_enet_clk(1);
+
+ return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ /*
+ * Defaults + Enable status LEDs (LED1: Activity, LED0: Link) & select
+ * 50 MHz RMII clock mode.
+ */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+#endif /* CONFIG_FEC_MXC */
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_FEC_MXC
+ setup_fec();
+#endif
+ return 0;
+}
+
+int checkboard(void)
+{
+ u32 cpurev = get_cpu_rev();
+
+ printf("Board: MYiR MYS-6ULX %s Single Board Computer\n",
+ get_imx_type((cpurev & 0xFF000) >> 12));
+
+ return 0;
+}
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+#include <common.h>
+#include <init.h>
+#include <spl.h>
+#include <asm/arch/clock.h>
+#include <asm/io.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
+#include <fsl_esdhc_imx.h>
+
+/* Configuration for Micron MT41K128M16JT-125, 32M x 16 x 8 -> 256MiB */
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+ .grp_addds = 0x00000030,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_ctlds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_ddrpke = 0x00000000,
+ .grp_ddrmode = 0x00020000,
+ .grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+ .dram_dqm0 = 0x00000030,
+ .dram_dqm1 = 0x00000030,
+ .dram_ras = 0x00000030,
+ .dram_cas = 0x00000030,
+ .dram_odt0 = 0x00000030,
+ .dram_odt1 = 0x00000030,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdclk_0 = 0x00000030,
+ .dram_sdqs0 = 0x00000030,
+ .dram_sdqs1 = 0x00000030,
+ .dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+ .p0_mpwldectrl0 = 0x00000000,
+ .p0_mpdgctrl0 = 0x41480148,
+ .p0_mprddlctl = 0x40403E42,
+ .p0_mpwrdlctl = 0x40405852,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+ .dsize = 0, /* Bus size = 16bit */
+ .cs_density = 32,
+ .ncs = 1,
+ .cs1_mirror = 0,
+ .rtt_wr = 1,
+ .rtt_nom = 1,
+ .walat = 1, /* Write additional latency */
+ .ralat = 5, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 1, /* Bank interleaving enabled */
+ .pd_fast_exit = 1,
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+ .ddr_type = DDR_TYPE_DDR3,
+ .refsel = 1, /* Refresh cycles at 32KHz */
+ .refr = 7, /* 8 refresh commands per refresh cycle */
+};
+
+/* MT41K128M16JT-125 (2Gb density) */
+static struct mx6_ddr3_cfg mem_ddr = {
+ .mem_speed = 1600,
+ .density = 2,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 14,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ writel(0xFFFFFFFF, &ccm->CCGR0);
+ writel(0xFFFFFFFF, &ccm->CCGR1);
+ writel(0xFFFFFFFF, &ccm->CCGR2);
+ writel(0xFFFFFFFF, &ccm->CCGR3);
+ writel(0xFFFFFFFF, &ccm->CCGR4);
+ writel(0xFFFFFFFF, &ccm->CCGR5);
+ writel(0xFFFFFFFF, &ccm->CCGR6);
+}
+
+static void spl_dram_init(void)
+{
+ mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+ mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+#ifdef CONFIG_FSL_ESDHC_IMX
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | \
+ PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+ MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_UART1_RTS_B__USDHC1_CD_B | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifndef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+#endif
+
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+ {
+ .esdhc_base = USDHC1_BASE_ADDR,
+ .max_bus_width = 4,
+ },
+#ifndef CONFIG_NAND_MXS
+ {
+ .esdhc_base = USDHC2_BASE_ADDR,
+ .max_bus_width = 8,
+ },
+#endif
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ return 1;
+}
+
+int board_mmc_init(struct bd_info *bis)
+{
+ int i, ret;
+
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ SETUP_IOMUX_PADS(usdhc1_pads);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+#ifndef CONFIG_NAND_MXS
+ case 1:
+ SETUP_IOMUX_PADS(usdhc2_pads);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+#endif
+ default:
+ printf("Warning - USDHC%d controller not supporting\n",
+ i + 1);
+ return 0;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret) {
+ printf("Warning: failed to initialize mmc dev %d\n", i);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+#endif /* CONFIG_FSL_ESDHC_IMX */
+
+void board_init_f(ulong dummy)
+{
+ ccgr_init();
+
+ /* Setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ /* Setup iomux and fec */
+ board_early_init_f();
+
+ /* Setup GP timer */
+ timer_init();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* DDR initialization */
+ spl_dram_init();
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x87800000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_ENV_SIZE=0x4000
+CONFIG_TARGET_MYS_6ULX=y
+CONFIG_SPL_TEXT_BASE=0x908000
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=8
+CONFIG_SPL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6ull-myir-mys-6ulx-eval"
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
+# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_DMA=y
+CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SPL_USB_HOST_SUPPORT=y
+CONFIG_SPL_USB_GADGET=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_SYS_MEMTEST_START=0x80000000
+CONFIG_SYS_MEMTEST_END=0x90000000
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+# CONFIG_RANDOM_UUID is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
+CONFIG_MTDPARTS_DEFAULT="gpmi-nand:512k(spl),1m(uboot),1m(uboot-dup),-(ubi)"
+CONFIG_CMD_UBI=y
+# CONFIG_ISO_PARTITION is not set
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_DM_I2C_GPIO=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_FSL_USDHC=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_NAND_MXS=y
+CONFIG_NAND_MXS_DT=y
+CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
+CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000
+CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND=0x180000
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_MXC_UART=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_SMBIOS_MANUFACTURER="MYiR"
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+
+ *
+ * Copyright (C) 2020 Linumiz
+ * Author: Parthiban Nallathambi <parthiban@linumiz.com>
+ */
+
+#ifndef __MYS_6ULX_H
+#define __MYS_6ULX_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* SPL options */
+#include "imx6_spl.h"
+
+#define CONFIG_SYS_FSL_USDHC_NUM 1
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
+
+/* Console configs */
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+/* Physical Memory Map */
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE SZ_256M
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* NAND */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+
+/* USB Configs */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console=ttymxc0,115200n8\0" \
+ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
+ "fdt_addr_r=0x82000000\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "pxefile_addr_r=0x87100000\0" \
+ "ramdisk_addr_r=0x82100000\0" \
+ "scriptaddr=0x87000000\0" \
+ BOOTENV
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(UBIFS, ubifs, 0) \
+ func(PXE, pxe, na) \
+ func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+#endif /* __MYS_6ULX_H */
projects / u-boot.git / commitdiff