--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_IOP480 1 /* This is a IOP480 CPU */
+#define CONFIG_ADCIOP 1 /* ...on a ADCIOP board */
+
+#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#define CONFIG_CPUCLOCK 66
+#define CONFIG_BUSCLOCK (CONFIG_CPUCLOCK)
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+
+#define CONFIG_IPADDR 10.0.18.222
+#define CONFIG_SERVERIP 10.0.18.190
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_ELF | \
+ CFG_CMD_ASKENV )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
+#define CFG_INIT_RAM_END 0x0f00 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFFFD0000
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x0AA9 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x0556 /* 2nd address for flash config cycles */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0 0x0002 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0000 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0004 /* 2 is standard */
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#if 1 /* Use NVRAM for environment variables */
+/*-----------------------------------------------------------------------
+ * NVRAM organization
+ */
+#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
+#define CFG_NVRAM_BASE_ADDR 0x10000000 /* NVRAM base address */
+#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
+#define CFG_ENV_SIZE 0x0400 /* Size of Environment vars */
+#define CFG_ENV_ADDR \
+ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
+#define CFG_NVRAM_VXWORKS_OFFS 0x7800 /* Offset for VxWorks eth-addr */
+
+#else /* Use FLASH for environment variables */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+
+#define CFG_ENV_SECT_SIZE 0x8000 /* see README - env sector total size */
+
+#endif
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ */
+#define CONFIG_PCI /* include pci support */
+#undef CONFIG_PCI_PNP
+
+#define CONFIG_NET_MULTI /* Multi ethernet cards support */
+
+#define CONFIG_TULIP
+
+#define CFG_ETH_DEV_FN 0x0000
+#define CFG_ETH_IOBASE 0x0fff0000
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 2048 /* For PLX IOP480 */
+#define CFG_CACHELINE_SIZE 16 /* For IBM 401/403 CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0xFFE00000 /* FLASH bank #1 */
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2002
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * board/config_CPCI440.h - configuration for esd CPCI-440 board
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_EBONY 1 /* Board is ebony */
+#define CONFIG_4xx 1 /* ... PPC4xx family */
+#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#undef CFG_DRAM_TEST /* Disable-takes long time! */
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */
+#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
+#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
+#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
+
+#define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000)
+#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000)
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in internal SRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 192 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#undef CFG_EXT_SERIAL_CLOCK /* (1843200 * 6) / * Ext clk @ 11.059 MHz */
+#define CONFIG_BAUDRATE 9600
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
+
+/*-----------------------------------------------------------------------
+ * NVRAM/RTC
+ *
+ * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located.
+ * The DS1743 code assumes this condition (i.e. -- it assumes the base
+ * address for the RTC registers is:
+ *
+ * CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE
+ *
+ *----------------------------------------------------------------------*/
+#define CFG_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs */
+#define CONFIG_RTC_DS174x 1 /* DS1743 RTC */
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#if 1 /* test-only */
+
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_FLASH_INCREMENT 0 /* there is only one bank */
+#define CFG_FLASH_PROTECTION 1 /* use hardware protection */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#undef CFG_FLASH_BASE
+#define CFG_FLASH_BASE 0xFF800000 /* test-only...*/
+
+#else /* test-only */
+
+#define CFG_MAX_FLASH_BANKS 3 /* number of banks */
+#define CFG_MAX_FLASH_SECT 32 /* sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#endif
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#if 0 /* test-only */
+#define CFG_ENV_IS_IN_NVRAM 1 /* Environment uses NVRAM */
+#undef CFG_ENV_IS_IN_FLASH /* ... not in flash */
+#undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */
+
+#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */
+#define CFG_ENV_ADDR \
+ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)
+#else
+
+#if 0 /* test-only */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x010 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
+ /* total size of a CAT24WC16 is 2048 bytes */
+#else
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#endif
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C /* I2c with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+ /* 16 byte page write mode using*/
+ /* last 4 bits of the address */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+#endif
+
+#define CONFIG_BOOTARGS "root=/dev/hda1 "
+#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */
+#define CONFIG_BOOTDELAY -1 /* disable autoboot */
+#define CONFIG_BAUDRATE 9600
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 1 /* PHY address */
+
+#if 0 /* test-only */
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_I2C | \
+ CFG_CMD_KGDB | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DATE | \
+ CFG_CMD_BEDBUG | \
+ CFG_CMD_ELF )
+#else
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_ELF | \
+ CFG_CMD_DATE | \
+ CFG_CMD_I2C | \
+ CFG_CMD_EEPROM )
+/* test-only: support fehlt bisher... */
+/* CFG_CMD_IDE | \*/
+/* CFG_CMD_PCI | \*/
+#endif
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#undef CONFIG_SPD_EEPROM /* don't use SPD EEPROM for setup */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#if 0 /* test-only */
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#endif
+
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#if 0
+#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
+#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#endif
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 32768 /* For IBM 440 CPUs */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+
+/* Configuration Port location */
+#define CONFIG_PORT_ADDR 0xF0000500
+
+/*-----------------------------------------------------------------------
+ * Definitions for Serial Presence Detect EEPROM address
+ * (to get SDRAM settings)
+ */
+#define SPD_EEPROM_ADDRESS 0x50
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
+#define CONFIG_CPU86 1 /* ...on a CPU86 board */
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#undef CONFIG_CONS_ON_SMC /* define if console on SMC */
+#define CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else*/
+#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
+
+#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
+#define CONFIG_BAUDRATE 230400
+#else
+#define CONFIG_BAUDRATE 9600
+#endif
+
+/*
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ *
+ */
+#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
+#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
+
+#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1)
+
+/*
+ * - Rx-CLK is CLK11
+ * - Tx-CLK is CLK12
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
+# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
+# define CFG_CPMFCR_RAMTYPE 0
+# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
+
+/*
+ * - Rx-CLK is CLK13
+ * - Tx-CLK is CLK14
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+# define CFG_CPMFCR_RAMTYPE 0
+# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#define CONFIG_8260_CLKIN 64000000 /* in Hz */
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#define CONFIG_PREBOOT \
+ "echo; " \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS; " \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+/*-----------------------------------------------------------------------
+ * I2C/EEPROM/RTC configuration
+ */
+#define CONFIG_SOFT_I2C /* Software I2C support enabled */
+
+# define CFG_I2C_SPEED 50000
+# define CFG_I2C_SLAVE 0xFE
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE (iop->pdir |= 0x00010000)
+#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
+#define I2C_READ ((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
+ else iop->pdat &= ~0x00010000
+#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
+ else iop->pdat &= ~0x00020000
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CONFIG_RTC_PCF8563
+#define CFG_I2C_RTC_ADDR 0x51
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*-----------------------------------------------------------------------
+ * Disk-On-Chip configuration
+ */
+
+#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
+
+#define CFG_DOC_SUPPORT_2000
+#define CFG_DOC_SUPPORT_MILLENNIUM
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configuration options
+ */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_BEDBUG | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DATE | \
+ CFG_CMD_I2C | \
+ CFG_CMD_DOC)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_RESET_ADDRESS 0xFFF00100 /* "bad" address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Flash configuration
+ */
+
+#define CFG_BOOTROM_BASE 0xFF800000
+#define CFG_BOOTROM_SIZE 0x00080000
+#define CFG_FLASH_BASE 0xFF000000
+#define CFG_FLASH_SIZE 0x00800000
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max num of memory banks */
+#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+/*-----------------------------------------------------------------------
+ * Other areas to be mapped
+ */
+
+/* CS3: Dual ported SRAM */
+#define CFG_DPSRAM_BASE 0x40000000
+#define CFG_DPSRAM_SIZE 0x00020000
+
+/* CS4: DiskOnChip */
+#define CFG_DOC_BASE 0xF4000000
+#define CFG_DOC_SIZE 0x00100000
+
+/* CS5: FDC37C78 controller */
+#define CFG_FDC37C78_BASE 0xF1000000
+#define CFG_FDC37C78_SIZE 0x00100000
+
+/* CS6: Board configuration registers */
+#define CFG_BCRS_BASE 0xF2000000
+#define CFG_BCRS_SIZE 0x00010000
+
+/* CS7: VME Extended Access Range */
+#define CFG_VMEEAR_BASE 0x80000000
+#define CFG_VMEEAR_SIZE 0x01000000
+
+/* CS8: VME Standard Access Range */
+#define CFG_VMESAR_BASE 0xFE000000
+#define CFG_VMESAR_SIZE 0x01000000
+
+/* CS9: VME Short I/O Access Range */
+#define CFG_VMESIOAR_BASE 0xFD000000
+#define CFG_VMESIOAR_SIZE 0x01000000
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * if you change bits in the HRCW, you must also change the CFG_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ */
+#if defined(CONFIG_BOOT_ROM)
+#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
+ HRCW_BPS01 | HRCW_CS10PC01)
+#else
+#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | HRCW_CS10PC01)
+#endif
+
+/* no slaves so just fill with zeros */
+#define CFG_HRCW_SLAVE1 0
+#define CFG_HRCW_SLAVE2 0
+#define CFG_HRCW_SLAVE3 0
+#define CFG_HRCW_SLAVE4 0
+#define CFG_HRCW_SLAVE5 0
+#define CFG_HRCW_SLAVE6 0
+#define CFG_HRCW_SLAVE7 0
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ *
+ * 60x SDRAM is mapped at CFG_SDRAM_BASE.
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+# define CFG_RAMBOOT
+#endif
+
+#if 0
+/* environment is in Flash */
+#define CFG_ENV_IS_IN_FLASH 1
+#ifdef CONFIG_BOOT_ROM
+# define CFG_ENV_ADDR (CFG_FLASH_BASE+0x70000)
+# define CFG_ENV_SIZE 0x10000
+# define CFG_ENV_SECT_SIZE 0x10000
+#endif
+#else
+/* environment is in EEPROM */
+#define CFG_ENV_IS_IN_EEPROM 1
+#define CFG_I2C_EEPROM_ADDR 0x58 /* EEPROM X24C16 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CFG_ENV_OFFSET 0
+#define CFG_ENV_SIZE 2048
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers 2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|\
+ HID0_DCI|HID0_IFEM|HID0_ABE)
+#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE)
+#define CFG_HID2 0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CFG_RMR RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration 4-25
+ *-----------------------------------------------------------------------
+ */
+#define BCR_APD01 0x10000000
+#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 4-31
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SIUMCR (SIUMCR_BBD|SIUMCR_DPPC00|SIUMCR_APPC10|\
+ SIUMCR_CS10PC01|SIUMCR_BCTLC10)
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control 4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control 9-8
+ *-----------------------------------------------------------------------
+ * Ensure DFBRG is Divide by 16
+ */
+#define CFG_SCCR SCCR_DFBRG01
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration 13-7
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR 0
+
+#define CFG_MIN_AM_MASK 0xC0000000
+/*-----------------------------------------------------------------------
+ * MPTPR - Memory Refresh Timer Prescaler Register 10-18
+ *-----------------------------------------------------------------------
+ */
+#define CFG_MPTPR 0x1F00
+
+/*-----------------------------------------------------------------------
+ * PSRT - Refresh Timer Register 10-16
+ *-----------------------------------------------------------------------
+ */
+#define CFG_PSRT 0x0f
+
+/*-----------------------------------------------------------------------
+ * PSRT - SDRAM Mode Register 10-10
+ *-----------------------------------------------------------------------
+ */
+
+ /* SDRAM initialization values for 8-column chips
+ */
+#define CFG_OR2_8COL (CFG_MIN_AM_MASK |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI0_A9 |\
+ ORxS_NUMR_12)
+
+#define CFG_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\
+ PSDMR_BSMA_A14_A16 |\
+ PSDMR_SDA10_PBI0_A10 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_1W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_1C |\
+ PSDMR_CL_2)
+
+ /* SDRAM initialization values for 9-column chips
+ */
+#define CFG_OR2_9COL (CFG_MIN_AM_MASK |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI0_A7 |\
+ ORxS_NUMR_13)
+
+#define CFG_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\
+ PSDMR_BSMA_A13_A15 |\
+ PSDMR_SDA10_PBI0_A9 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_1W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_1C |\
+ PSDMR_CL_2)
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus Machine PortSz Device
+ * ---- --- ------- ------ ------
+ * 0 60x GPCM 8 bit Boot ROM
+ * 1 60x GPCM 64 bit FLASH
+ * 2 60x SDRAM 64 bit SDRAM
+ *
+ */
+
+#define CFG_MRS_OFFS 0x00000000
+
+#ifdef CONFIG_BOOT_ROM
+/* Bank 0 - Boot ROM
+ */
+#define CFG_BR0_PRELIM ((CFG_BOOTROM_BASE & BRx_BA_MSK)|\
+ BRx_PS_8 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_BOOTROM_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_3_CLK |\
+ ORxU_EHTR_8IDLE)
+
+/* Bank 1 - FLASH
+ */
+#define CFG_BR1_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_3_CLK |\
+ ORxU_EHTR_8IDLE)
+
+#else /* CONFIG_BOOT_ROM */
+/* Bank 0 - FLASH
+ */
+#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_3_CLK |\
+ ORxU_EHTR_8IDLE)
+
+/* Bank 1 - Boot ROM
+ */
+#define CFG_BR1_PRELIM ((CFG_BOOTROM_BASE & BRx_BA_MSK)|\
+ BRx_PS_8 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_BOOTROM_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_3_CLK |\
+ ORxU_EHTR_8IDLE)
+
+#endif /* CONFIG_BOOT_ROM */
+
+
+/* Bank 2 - 60x bus SDRAM
+ */
+#ifndef CFG_RAMBOOT
+#define CFG_BR2_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_SDRAM_P |\
+ BRx_V)
+
+#define CFG_OR2_PRELIM CFG_OR2_9COL
+
+#define CFG_PSDMR CFG_PSDMR_9COL
+#endif /* CFG_RAMBOOT */
+
+/* Bank 3 - Dual Ported SRAM
+ */
+#define CFG_BR3_PRELIM ((CFG_DPSRAM_BASE & BRx_BA_MSK) |\
+ BRx_PS_16 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR3_PRELIM (P2SZ_TO_AM(CFG_DPSRAM_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_SETA)
+
+/* Bank 4 - DiskOnChip
+ */
+#define CFG_BR4_PRELIM ((CFG_DOC_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR4_PRELIM (P2SZ_TO_AM(CFG_DOC_SIZE) |\
+ ORxG_ACS_DIV2 |\
+ ORxG_SCY_5_CLK |\
+ ORxU_EHTR_8IDLE)
+
+/* Bank 5 - FDC37C78 controller
+ */
+#define CFG_BR5_PRELIM ((CFG_FDC37C78_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR5_PRELIM (P2SZ_TO_AM(CFG_FDC37C78_SIZE) |\
+ ORxG_ACS_DIV2 |\
+ ORxG_SCY_8_CLK |\
+ ORxU_EHTR_8IDLE)
+
+/* Bank 6 - Board control registers
+ */
+#define CFG_BR6_PRELIM ((CFG_BCRS_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR6_PRELIM (P2SZ_TO_AM(CFG_BCRS_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_SCY_5_CLK)
+
+/* Bank 7 - VME Extended Access Range
+ */
+#define CFG_BR7_PRELIM ((CFG_VMEEAR_BASE & BRx_BA_MSK) |\
+ BRx_PS_32 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR7_PRELIM (P2SZ_TO_AM(CFG_VMEEAR_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_SETA)
+
+/* Bank 8 - VME Standard Access Range
+ */
+#define CFG_BR8_PRELIM ((CFG_VMESAR_BASE & BRx_BA_MSK) |\
+ BRx_PS_16 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR8_PRELIM (P2SZ_TO_AM(CFG_VMESAR_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_SETA)
+
+/* Bank 9 - VME Short I/O Access Range
+ */
+#define CFG_BR9_PRELIM ((CFG_VMESIOAR_BASE & BRx_BA_MSK) |\
+ BRx_PS_16 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR9_PRELIM (P2SZ_TO_AM(CFG_VMESIOAR_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_SETA)
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_IOP480 1 /* This is a IOP480 CPU */
+#define CONFIG_DASA_SIM 1 /* ...on a DASA_SIM board */
+
+#define CONFIG_BOARD_PRE_INIT 1 /* call board_pre_init() */
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#define CONFIG_CPUCLOCK 66
+#define CONFIG_BUSCLOCK (CONFIG_CPUCLOCK)
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
+#define CONFIG_BOOTCOMMAND "bootm ffe00000" /* autoboot command */
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_IPADDR 10.0.18.222
+#define CONFIG_SERVERIP 10.0.18.190
+
+#if 0
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_BSP | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_ELF )
+#else
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_BSP )
+#endif
+
+#if 0 /* Does not appear to be used?! If it is used, needs to be fixed */
+#define CONFIG_SOFT_I2C /* Software I2C support enabled */
+#endif
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
+#define CFG_INIT_RAM_END 0x0f00 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFFFD0000
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 128 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_FLASH_WORD_SIZE unsigned char /* flash word size (width) */
+#define CFG_FLASH_ADDR0 0x0AA9 /* 1st address for flash config cycles */
+#define CFG_FLASH_ADDR1 0x0556 /* 2nd address for flash config cycles */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0 0x0002 /* 0 is standard */
+#define CFG_FLASH_READ1 0x0000 /* 1 is standard */
+#define CFG_FLASH_READ2 0x0004 /* 2 is standard */
+
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x00010000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+
+#if 0
+#define CFG_ENV_SECT_SIZE 0x8000 /* see README - env sector total size */
+#else
+#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
+#endif
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ */
+#define CONFIG_PCI /* include pci support */
+#undef CONFIG_PCI_PNP
+
+#define CONFIG_NET_MULTI /* Multi ethernet cards support */
+
+#define CONFIG_TULIP
+
+#define CFG_ETH_DEV_FN 0x0000
+#define CFG_ETH_IOBASE 0x0fff0000
+#define CFG_PCI9054_DEV_FN 0x0800
+#define CFG_PCI9054_IOBASE 0x0eff0000
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 2048 /* For PLX IOP480 */
+#define CFG_CACHELINE_SIZE 16 /* For IBM 401/403 CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC850 1 /* This is a MPC850 CPU */
+#define CONFIG_ESTEEM192E 1 /* ...on a EST ESTEEM192E */
+
+#define CONFIG_FLASH_16BIT 1 /* Rom 16 bit data bus */
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+
+#define MPC8XX_FACT 10 /* Multiply by 10 */
+#define MPC8XX_XIN 4915200 /* 4.915200 MHz in - ??? - XXX */
+#define CFG_PLPRCR_MF ((MPC8XX_FACT-1) << 20)
+#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) /* 49,152,000 Hz */
+
+#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ /* Force it - dont measure it */
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#define CONFIG_BAUDRATE 9600
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+#define CONFIG_BOOTCOMMAND "bootm 40030000" /* autoboot command */
+
+#define CONFIG_BOOTARGS "root=/dev/ram rw ramdisk=8192 " \
+ "ip=100.100.100.21:100.100.100.14:100.100.100.1:255.0.0.0 "
+/*
+ * Miscellaneous configurable options
+ */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "BOOT: " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 8 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFF000000
+
+ /*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x40000000
+#ifdef DEBUG
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
+#endif
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+
+/*-----------------------------------------------------------------------
+ * SUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) /* DBGC00 */
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
+
+/* (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) */
+
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit - leave PLL multiplication factor unchanged !
+ */
+#define CFG_PLPRCR (CFG_PLPRCR_MF | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+#define CFG_SCCR (SCCR_TBS | \
+ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+#define CFG_PCMCIA_INTERRUPT SIU_LEVEL6
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define CFG_DER 0x2002000F*/
+#define CFG_DER 0
+/*#define CFG_DER 0x02002000 */
+
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
+
+/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH 0x00000160
+ /*(OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \
+ OR_SCY_5_CLK | OR_EHTR) */
+
+#define CFG_OR0_REMAP 0x80000160 /*(CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)*/
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM ( FLASH_BASE0_PRELIM | 0x00000801 )
+
+#define CFG_OR1_REMAP CFG_OR0_REMAP
+#define CFG_OR1_PRELIM CFG_OR0_PRELIM
+#define CFG_BR1_PRELIM ( FLASH_BASE1_PRELIM | 0x00000801 )
+
+/*
+ * BR2/3 and OR2/3 (SDRAM)
+ *
+ */
+#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
+#define SDRAM_BASE3_PRELIM 0x04000000 /* SDRAM bank #1 */
+#define SDRAM_MAX_SIZE 0x02000000 /* max 32 MB per bank */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CFG_OR_TIMING_SDRAM 0x00000A00
+
+#define CFG_OR2_PRELIM 0xFC000E00
+#define CFG_BR2_PRELIM (SDRAM_BASE2_PRELIM | 0x00000081)
+
+#define CFG_OR3_PRELIM CFG_OR2_PRELIM
+#define CFG_BR3_PRELIM (SDRAM_BASE3_PRELIM | 0x00000081)
+
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL 0x18803112
+#define CFG_MAMR_9COL 0x18803112 /* same as 8 column because its just easier to port with*/
+
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
--- /dev/null
+ /*
+ * A collection of structures, addresses, and values associated with
+ * the Motorola 860T FADS board. Copied from the MBX stuff.
+ * Magnus Damm added defines for 8xxrom and extended bd_info.
+ * Helmut Buchsbaum added bitvalues for BCSRx
+ *
+ * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ */
+
+/*
+ * 1999-nov-26: The FADS is using the following physical memorymap:
+ *
+ * ff020000 -> ff02ffff : pcmcia
+ * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxrom
+ * ff000000 -> ff00ffff : IMAP internal in the cpu
+ * fe000000 -> ffnnnnnn : flash connected to CS0, setup by 8xxrom
+ * 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom
+ */
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#include <mpc8xx_irq.h>
+
+#define CONFIG_MPC850 1
+#define CONFIG_MPC850SAR 1
+#define CONFIG_FADS 1
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 9600
+
+#if 0
+#define MPC8XX_FACT 10 /* Multiply by 10 */
+#define MPC8XX_XIN 50000000 /* 50 MHz in */
+#else
+#define MPC8XX_FACT 12 /* Multiply by 12 */
+#define MPC8XX_XIN 4000000 /* 4 MHz in */
+#endif
+#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#if 1
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_BOOTCOMMAND "bootm 02880000" /* autoboot command */
+#define CONFIG_BOOTARGS " "
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#undef CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT ":>" /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x00004000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00800000 /* 0 ... 8 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x00100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFF000000
+#define CFG_IMMR_SIZE ((uint)(64 * 1024))
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Also NOTE that it doesn't mean SDRAM - it means MEMORY.
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x02800000
+#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
+#if 0
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 128 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
+#endif
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer *
+ * interrupt status bit - leave PLL multiplication factor unchanged !
+ */
+#define CFG_PLPRCR (((MPC8XX_FACT-1) << 20) | \
+ PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+#define CFG_SCCR (SCCR_TBS | \
+ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+
+ /*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0
+
+/* Because of the way the 860 starts up and assigns CS0 the
+* entire address space, we have to set the memory controller
+* differently. Normally, you write the option register
+* first, and then enable the chip select by writing the
+* base register. For CS0, you must write the base register
+* first, followed by the option register.
+*/
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+/* the other CS:s are determined by looking at parameters in BCSRx */
+
+
+#define BCSR_ADDR ((uint) 0x02100000)
+#define BCSR_SIZE ((uint)(64 * 1024))
+
+#define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */
+
+#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xFFE00000 /* OR addr mask */
+
+/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+
+/* BCSRx - Board Control and Status Registers */
+#define CFG_OR1_REMAP CFG_OR0_REMAP
+#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
+#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V )
+
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+#define CFG_MAMR 0x13a01114
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+
+/* values according to the manual */
+
+
+#define PCMCIA_MEM_ADDR ((uint)0xff020000)
+#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
+
+#define BCSR0 ((uint) (BCSR_ADDR + 00))
+#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
+#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
+#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
+#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
+
+/* FADS bitvalues by Helmut Buchsbaum
+ * see MPC8xxADS User's Manual for a proper description
+ * of the following structures
+ */
+
+#define BCSR0_ERB ((uint)0x80000000)
+#define BCSR0_IP ((uint)0x40000000)
+#define BCSR0_BDIS ((uint)0x10000000)
+#define BCSR0_BPS_MASK ((uint)0x0C000000)
+#define BCSR0_ISB_MASK ((uint)0x01800000)
+#define BCSR0_DBGC_MASK ((uint)0x00600000)
+#define BCSR0_DBPC_MASK ((uint)0x00180000)
+#define BCSR0_EBDF_MASK ((uint)0x00060000)
+
+#define BCSR1_FLASH_EN ((uint)0x80000000)
+#define BCSR1_DRAM_EN ((uint)0x40000000)
+#define BCSR1_ETHEN ((uint)0x20000000)
+#define BCSR1_IRDEN ((uint)0x10000000)
+#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
+#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
+#define BCSR1_BCSR_EN ((uint)0x02000000)
+#define BCSR1_RS232EN_1 ((uint)0x01000000)
+#define BCSR1_PCCEN ((uint)0x00800000)
+#define BCSR1_PCCVCC0 ((uint)0x00400000)
+#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
+#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
+#define BCSR1_RS232EN_2 ((uint)0x00040000)
+#define BCSR1_SDRAM_EN ((uint)0x00020000)
+#define BCSR1_PCCVCC1 ((uint)0x00010000)
+
+#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
+#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
+#define BCSR2_DRAM_PD_SHIFT (23)
+#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
+#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
+
+#define BCSR3_DBID_MASK ((ushort)0x3800)
+#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
+#define BCSR3_BREVNR0 ((ushort)0x0080)
+#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
+#define BCSR3_BREVN1 ((ushort)0x0008)
+#define BCSR3_BREVN2_MASK ((ushort)0x0003)
+
+#define BCSR4_ETHLOOP ((uint)0x80000000)
+#define BCSR4_TFPLDL ((uint)0x40000000)
+#define BCSR4_TPSQEL ((uint)0x20000000)
+#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
+#ifdef CONFIG_MPC823
+#define BCSR4_USB_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860SAR
+#define BCSR4_UTOPIA_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC860SAR */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETH_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_USB_SPEED ((uint)0x04000000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHCFG0 ((uint)0x04000000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_VCCO ((uint)0x02000000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHFDE ((uint)0x02000000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_VIDEO_ON ((uint)0x00800000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC823
+#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHCFG1 ((uint)0x00400000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_VIDEO_RST ((uint)0x00200000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHRST ((uint)0x00200000)
+#endif /* CONFIG_MPC860T */
+#define BCSR4_MODEM_EN ((uint)0x00100000)
+#define BCSR4_DATA_VOICE ((uint)0x00080000)
+
+#define CONFIG_DRAM_50MHZ 1
+#define CONFIG_SDRAM_50MHZ
+
+#ifdef CONFIG_MPC860T
+
+/* Interrupt level assignments.
+*/
+#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
+
+#endif /* CONFIG_MPC860T */
+
+/* We don't use the 8259.
+*/
+#define NR_8259_INTS 0
+
+/* Machine type
+*/
+#define _MACH_8xx (_MACH_fads)
+
+#define CONFIG_DISK_SPINUP_TIME 1000000
+
+
+/* PCMCIA configuration */
+
+#define PCMCIA_MAX_SLOTS 2
+
+#ifdef CONFIG_MPC860
+#define PCMCIA_SLOT_A 1
+#endif
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
+#define CONFIG_FLAGADM 1 /* ...on a FLAGA DM */
+#define CONFIG_8xx_GCLK_FREQ 48000000 /*48MHz*/
+
+#undef CONFIG_8xx_CONS_SMC1 /* Console is on SMC1 */
+#define CONFIG_8xx_CONS_SMC2 1
+#undef CONFIG_8xx_CONS_NONE
+
+#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
+#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+#if 0
+#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=bootp"
+#define CONFIG_BOOTCOMMAND \
+ "setenv bootargs root=/dev/ram ip=off panic=1;" \
+ "bootm 40040000 400e0000"
+#else
+#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=bootp panic=1"
+#define CONFIG_BOOTCOMMAND "bootp 0x400000; bootm 0x400000"
+#endif /* 0|1*/
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+/*#define CONFIG_WATCHDOG*/ /* watchdog enabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS (CFG_CMD_BDI | CFG_CMD_IMI | CFG_CMD_CACHE | \
+ CFG_CMD_MEMORY | CFG_CMD_FLASH | CFG_CMD_LOADB | CFG_CMD_LOADS | \
+ CFG_CMD_ENV | CFG_CMD_REGINFO | CFG_CMD_IMMAP | CFG_CMD_NET)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "EEG> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0f00000 /* 1 ... 15 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x40040000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFF000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x40000000
+#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+/* This is a litlebit wasteful, but one sector is 128kb and we have to
+ * assigne a whole sector for the environment, so that we can safely
+ * erase and write it without disturbing the boot sector
+ */
+#define CFG_ENV_OFFSET 0x20000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#ifdef CONFIG_WATCHDOG
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_SWF | SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_PRE_SIUMCR (SIUMCR_DBGC11 | SIUMCR_MPRE | \
+ SIUMCR_MLRC01 | SIUMCR_GB5E)
+#define CFG_SIUMCR (CFG_PRE_SIUMCR | SIUMCR_DLK)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit miltiplier of 0x00b i.e. operation clock is
+ * 4MHz * (0x00b+1) = 4MHz * 12 = 48MHz
+ */
+#define CFG_PLPRCR (0x00b00000 | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+#define CFG_SCCR ( SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+
+#define CFG_DER 0
+
+/*
+ * In the Flaga DM we have:
+ * Flash on BR0/OR0/CS0a at 0x40000000
+ * Display on BR1/OR1/CS1 at 0x20000000
+ * SDRAM on BR2/OR2/CS2 at 0x00000000
+ * Free BR3/OR3/CS3
+ * DSP1 on BR4/OR4/CS4 at 0x80000000
+ * DSP2 on BR5/OR5/CS5 at 0xa0000000
+ *
+ * For now we just configure the Flash and the SDRAM and leave the others
+ * untouched.
+*/
+
+#define CFG_FLASH_PROTECTION 0
+
+#define FLASH_BASE0 0x40000000 /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_OR_AM 0xff000000 /* OR addr mask */
+#define CFG_OR_ATM 0x00006000
+
+/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | \
+ OR_SCY_3_CLK | OR_TRLX | OR_EHTR )
+
+#define CFG_OR0_PRELIM (CFG_OR_AM | CFG_OR_ATM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM ((FLASH_BASE0 & BR_BA_MSK) | BR_PS_16 | BR_V )
+
+/*
+ * BR2 and OR2 (SDRAM)
+ *
+ */
+#define SDRAM_BASE2 0x00000000 /* SDRAM bank #0 */
+#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CFG_OR_TIMING_SDRAM ( 0x00000800 )
+
+#define CFG_OR2_PRELIM (CFG_OR_AM | CFG_OR_TIMING_SDRAM)
+#define CFG_BR2_PRELIM ((SDRAM_BASE2 & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+#define CFG_BR2 CFG_BR2_PRELIM
+#define CFG_OR2 CFG_OR2_PRELIM
+
+/*
+ * MAMR settings for SDRAM
+ */
+#define CFG_MAMR_48_SDR (CFG_MAMR_PTA | MAMR_WLFA_1X | MAMR_RLFA_1X \
+ | MAMR_G0CLA_A11)
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA 0x0F000000
+
+/*
+ * BR4 and OR4 (DSP1)
+ *
+ * We do not wan't preliminary setup of the DSP, anyway we need the
+ * UPMB setup correctly before we can access the DSP.
+ *
+*/
+#define DSP_BASE 0x80000000
+
+#define CFG_OR4 ( OR_AM_MSK | OR_CSNT_SAM | OR_BI | OR_G5LS)
+#define CFG_BR4 ( (DSP_BASE & BR_BA_MSK) | BR_PS_16 | BR_MS_UPMB | BR_V )
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * Parameters for GTH board
+ * Based on FADS860T
+ * by thomas.lange@corelatus.com
+
+ * A collection of structures, addresses, and values associated with
+ * the Motorola 860T FADS board. Copied from the MBX stuff.
+ * Magnus Damm added defines for 8xxrom and extended bd_info.
+ * Helmut Buchsbaum added bitvalues for BCSRx
+ *
+ * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ */
+
+/*
+ * ff000000 -> ff00ffff : IMAP internal in the cpu
+ * e0000000 -> ennnnnnn : pcmcia
+ * 98000000 -> 983nnnnn : FPGA 4MB
+ * 90000000 -> 903nnnnn : FPGA 4MB
+ * 80000000 -> 80nnnnnn : flash connected to CS0, final ( real ) location
+ * 00000000 -> nnnnnnnn : sdram
+ */
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#include <mpc8xx_irq.h>
+
+#define CONFIG_MPC860 1
+#define CONFIG_MPC860T 1
+#define CONFIG_GTH 1
+
+#define CONFIG_MISC_INIT_R 1
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+
+#define MPC8XX_FACT 3 /* Multiply by 3 */
+#define MPC8XX_XIN 16384000 /* 16.384 MHz */
+#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
+
+#define CONFIG_BOOTDELAY 1 /* autoboot after 0 seconds */
+
+#define CONFIG_ENV_OVERWRITE 1 /* Allow change of ethernet address */
+
+#define CONFIG_BOOT_RETRY_TIME 5 /* Retry boot in 5 secs */
+
+#define CONFIG_RESET_TO_RETRY 1 /* If timeout waiting for command, perform a reset */
+
+/* Only interrupt boot if space is pressed */
+/* If a long serial cable is connected but */
+/* other end is dead, garbage will be read */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT "Press space to abort autoboot in %d second\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "d"
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+#if 0
+/* Net boot */
+/* Loads a tftp image and starts it */
+#define CONFIG_BOOTCOMMAND "bootp;bootm 100000" /* autoboot command */
+#define CONFIG_BOOTARGS "panic=1"
+#else
+/* Compact flash boot */
+#define CONFIG_BOOTARGS "panic=1 root=/dev/hda7"
+#define CONFIG_BOOTCOMMAND "disk 100000 0:5;bootm 100000"
+#endif
+
+/* Enable watchdog */
+#define CONFIG_WATCHDOG 1
+
+/* choose SCC1 ethernet (10BASET on motherboard)
+ * or FEC ethernet (10/100 on daughterboard)
+ */
+#if 1
+#define CONFIG_SCC1_ENET 1 /* use SCC1 ethernet */
+#undef CONFIG_FEC_ENET /* disable FEC ethernet */
+#define CFG_DISCOVER_PHY
+#else
+#undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */
+#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
+#define CFG_DISCOVER_PHY
+#endif
+#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
+#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
+#endif
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_IDE)
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_PROMPT "=>" /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
+
+/* Default location to load data from net */
+#define CFG_LOAD_ADDR 0x100000
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFF000000
+#define CFG_IMMR_SIZE ((uint)(64 * 1024))
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+
+#define CFG_FLASH_BASE 0x80000000
+
+#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
+
+#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+
+#define CFG_MONITOR_BASE TEXT_BASE
+
+#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#undef CFG_ENV_IS_IN_EEPROM
+#define CFG_ENV_OFFSET 0x000E0000
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+#define CFG_ENV_SECT_SIZE 0x50000 /* see README - env sector total size */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+
+/*FIXME dont use for now */
+/*#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
+/*#define CFG_RTCSC (RTCSC_RTF) */
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+/* PITE */
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * set the PLL, the low-power modes and the reset control (15-29)
+ */
+#define CFG_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
+ PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+
+/* FIXME check values */
+#define SCCR_MASK SCCR_EBDF11
+#define CFG_SCCR (SCCR_TBS|SCCR_RTSEL|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00)
+
+ /*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0
+
+/* Because of the way the 860 starts up and assigns CS0 the
+* entire address space, we have to set the memory controller
+* differently. Normally, you write the option register
+* first, and then enable the chip select by writing the
+* base register. For CS0, you must write the base register
+* first, followed by the option register.
+*/
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+/* the other CS:s are determined by looking at parameters in BCSRx */
+
+#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+
+#define CFG_REMAP_OR_AM 0xFF800000 /* 4 MB OR addr mask */
+#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
+
+#define FPGA_2_BASE 0x90000000
+#define FPGA_3_BASE 0x98000000
+
+/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+
+
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16 )
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#define CONFIG_ETHADDR DE:AD:BE:EF:00:01 /* Ethernet address */
+
+#ifdef CONFIG_MPC860T
+
+/* Interrupt level assignments.
+*/
+#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
+
+#endif /* CONFIG_MPC860T */
+
+/* We don't use the 8259.
+*/
+#define NR_8259_INTS 0
+
+/* Machine type
+*/
+#define _MACH_8xx (_MACH_gth)
+
+#ifdef CONFIG_MPC860
+#define PCMCIA_SLOT_A 1
+#define CONFIG_PCMCIA_SLOT_A 1
+#endif
+
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET 0x0100
+
+#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ /* Force it - dont measure it */
+
+#define PA_FRONT_LED ((u16)0x4) /* PA 13 */
+#define PA_FL_CONFIG ((u16)0x20) /* PA 10 */
+#define PA_FL_CE ((u16)0x1000) /* PA 3 */
+
+#define PB_ID_GND ((u32)1) /* PB 31 */
+#define PB_REV_1 ((u32)2) /* PB 30 */
+#define PB_REV_0 ((u32)4) /* PB 29 */
+#define PB_BLUE_LED ((u32)0x400) /* PB 21 */
+#define PB_EEPROM ((u32)0x800) /* PB 20 */
+#define PB_ID_3 ((u32)0x2000) /* PB 18 */
+#define PB_ID_2 ((u32)0x4000) /* PB 17 */
+#define PB_ID_1 ((u32)0x8000) /* PB 16 */
+#define PB_ID_0 ((u32)0x10000) /* PB 15 */
+
+/* NOTE. This is reset for 100Mbit port only */
+#define PC_ENET100_RESET ((ushort)0x0080) /* PC 8 */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001, 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <mpc8xx_irq.h>
+
+
+# ifdef DEBUG
+# warning DEBUG Defined
+# endif /* DEBUG */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MPC860 1
+#define CONFIG_IAD210 1 /* ...on a IAD210 module */
+#define CONFIG_MPC860T 1
+#define CONFIG_MPC862 1
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+
+#undef CONFIG_8xx_CONS_SMC1
+#undef CONFIG_8xx_CONS_SMC2
+#define CONFIG_8xx_CONS_SCC2 /* V24 on SCC2 */
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 9600
+
+
+# define MPC8XX_FACT 16
+# define CONFIG_8xx_GCLK_FREQ (64000000L) /* define if can't use get_gclk_freq */
+# define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#if 0
+# define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+# define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+/* using this define saves us updating another source file */
+#define CONFIG_BOARD_PRE_INIT 1
+
+#undef CONFIG_BOOTARGS
+/* #define CONFIG_BOOTCOMMAND \
+ "bootp;" \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
+ "bootm"
+*/
+
+#define CONFIG_BOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs" \
+ "ip=192.168.28.129:139.10.137.138:192.168.28.1:255.255.255.0:iadlinux002::off; " \
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/* #define CONFIG_STATUS_LED 1*/ /* Status LED enabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+# undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */
+# define CONFIG_FEC_ENET 1 /* use FEC ethernet */
+# define CFG_DISCOVER_PHY 1
+# define CONFIG_FEC_UTOPIA 1
+# define CONFIG_ETHADDR 08:00:06:26:A2:6D
+# define CONFIG_IPADDR 192.168.28.128
+# define CONFIG_SERVERIP 139.10.137.138
+# define CFG_DISCOVER_PHY 1
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+/* enable I2C and select the hardware/software driver */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+# define CFG_I2C_SPEED 50000
+# define CFG_I2C_SLAVE 0xDD
+# define CFG_I2C_EEPROM_ADDR 0x50
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL 0x00000020 /* PB 26 */
+#define PB_SDA 0x00000010 /* PB 27 */
+
+#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
+#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
+#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DATE )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x00100000
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFFF00000
+#define CFG_IMMR_SIZE ((uint)(64 * 1024))
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x08000000
+#define CFG_FLASH_SIZE ((uint)(4 * 1024 * 1024)) /* max 16Mbyte */
+
+#define CFG_RESET_ADDRESS 0xFFF00100
+
+#if defined(DEBUG)
+# define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+# define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#endif
+
+# define CFG_MONITOR_BASE CFG_FLASH_BASE
+# define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x8000
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * set the PLL, the low-power modes and the reset control (15-29)
+ */
+#define CFG_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
+ PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+
+#define CFG_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \
+ SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
+ SCCR_DFLCD000 |SCCR_DFALCD00 )
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration Register 19-4
+ *-----------------------------------------------------------------------
+ */
+/* +0x09C4 => DRQP = 10 (IDMA requests have lowest priority) */
+#define CFG_RCCR 0x0020
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCMCIA_MEM_ADDR ((uint)0xff020000)
+#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0
+
+/* Because of the way the 860 starts up and assigns CS0 the
+* entire address space, we have to set the memory controller
+* differently. Normally, you write the option register
+* first, and then enable the chip select by writing the
+* base register. For CS0, you must write the base register
+* first, followed by the option register.
+*/
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0 and OR0 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM 0xF8000000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xF8000000 /* OR addr mask */
+
+/* FLASH timing:
+ TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | \
+ OR_SCY_3_CLK | OR_EHTR)
+
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+
+/*
+ * BR2/3 and OR2/3 (SDRAM)
+ *
+ */
+#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM bank #0 */
+#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+
+#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | OR_CSNT_SAM | OR_BI | OR_ACS_DIV4)
+#define CFG_BR2_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#define CFG_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V)
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA 124 /* start with divider for 64 MHz */
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
+#define CFG_MPTPR MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+#define CFG_MAMR ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLB_A11 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_8X)
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#ifdef CONFIG_MPC860T
+
+/* Interrupt level assignments.
+*/
+#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
+
+#endif /* CONFIG_MPC860T */
+
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
+#define CONFIG_IVML24 1 /* ...on a IVML24 board */
+
+#if defined (CONFIG_IVML24_16M)
+# define CONFIG_IDENT_STRING " IVML24"
+#elif defined (CONFIG_IVML24_32M)
+# define CONFIG_IDENT_STRING " IVML24_128"
+#elif defined (CONFIG_IVML24_64M)
+# define CONFIG_IDENT_STRING " IVML24_256"
+#endif
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+#define CONFIG_8xx_GCLK_FREQ 50331648
+
+#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
+
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
+
+#define CONFIG_BOOTARGS "root=/dev/nfs rw " \
+ "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \
+ "nfsaddrs=10.0.0.99:10.0.0.2"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_IDE)
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_BOOTP_MASK \
+ ((CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) & ~CONFIG_BOOTP_GATEWAY)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x00100000 /* default load address */
+
+#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
+
+#define CFG_PB_12V_ENABLE 0x00002000 /* PB 18 */
+#define CFG_PB_ILOCK_SWITCH 0x00004000 /* PB 17 */
+#define CFG_PB_SDRAM_CLKE 0x00008000 /* PB 16 */
+#define CFG_PB_ETH_POWERDOWN 0x00010000 /* PB 15 */
+#define CFG_PB_IDE_MOTOR 0x00020000 /* PB 14 */
+
+#define CFG_PC_ETH_RESET ((ushort)0x0010) /* PC 11 */
+#define CFG_PC_IDE_RESET ((ushort)0x0020) /* PC 10 */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFFF00000 /* was: 0xFF000000 */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+
+#if defined (CONFIG_IVML24_16M)
+# define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#elif defined (CONFIG_IVML24_32M)
+# define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */
+#elif defined (CONFIG_IVML24_64M)
+# define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */
+#endif
+
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFF000000
+#ifdef DEBUG
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#endif
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x7A000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+
+# if defined (CONFIG_IVML24_16M)
+# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+# elif defined (CONFIG_IVML24_32M)
+# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWP)
+# elif defined (CONFIG_IVML24_64M)
+# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWP)
+# endif
+
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+/* EARB, DBGC and DBPC are initialised by the HCW */
+/* => 0x000000C0 */
+#define CFG_SIUMCR (SIUMCR_BSC | SIUMCR_GB5E)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit, set PLL multiplication factor !
+ */
+/* 0x00B0C0C0 */
+#define CFG_PLPRCR \
+ ( (11 << PLPRCR_MF_SHIFT) | \
+ PLPRCR_SPLSS | PLPRCR_TEXPS | /*PLPRCR_TMIST|*/ \
+ /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \
+ PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \
+ )
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+/* 0x01800014 */
+#define CFG_SCCR (SCCR_COM01 | /*SCCR_TBS|*/ \
+ SCCR_RTDIV | SCCR_RTSEL | \
+ /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \
+ SCCR_EBDF00 | SCCR_DFSYNC00 | \
+ SCCR_DFBRG00 | SCCR_DFNL000 | \
+ SCCR_DFNH000 | SCCR_DFLCD101 | \
+ SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+/* 0x00C3 */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration Register 19-4
+ *-----------------------------------------------------------------------
+ */
+/* TIMEP=2 */
+#define CFG_RCCR 0x0200
+
+/*-----------------------------------------------------------------------
+ * RMDS - RISC Microcode Development Support Control Register
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RMDS 0
+
+/*-----------------------------------------------------------------------
+ *
+ * Interrupt Levels
+ *-----------------------------------------------------------------------
+ */
+#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */
+#define CONFIG_IDE_RESET 1 /* reset for ide supported */
+
+#define CFG_IDE_MAXBUS 1 /* The IVML24 has only 1 IDE bus*/
+#define CFG_IDE_MAXDEVICE 1 /* ... and only 1 IDE device */
+
+#define CFG_ATA_BASE_ADDR 0xFE100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#undef CFG_ATA_IDE1_OFFSET /* only one IDE bus available */
+
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define CFG_DER 0x2002000F*/
+#define CFG_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0 and OR0 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0xFF000000 /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+/* EPROMs are 512kb */
+#define CFG_REMAP_OR_AM 0xFFF80000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xFFF80000 /* OR addr mask */
+
+/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH (OR_SCY_5_CLK | OR_EHTR)
+
+#define CFG_OR0_REMAP ( CFG_REMAP_OR_AM | OR_ACS_DIV4 | OR_BI | \
+ CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | OR_ACS_DIV4 | OR_BI | \
+ CFG_OR_TIMING_FLASH)
+/* 16 bit, bank valid */
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
+
+/*
+ * BR1/OR1 - ELIC SACCO bank @ 0xFE000000
+ *
+ * AM=0xFFFF8 ATM=0 CSNT/SAM=1 ACS/G5LA/G5LS=3 BIH=1 SCY=2 SETA=0 TRLX=1 EHTR=1
+ */
+#define ELIC_SACCO_BASE 0xFE000000
+#define ELIC_SACCO_OR_AM 0xFFFF8000
+#define ELIC_SACCO_TIMING (OR_SCY_2_CLK | OR_TRLX | OR_EHTR)
+
+#define CFG_OR1 (ELIC_SACCO_OR_AM | OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \
+ ELIC_SACCO_TIMING)
+#define CFG_BR1 ((ELIC_SACCO_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
+
+/*
+ * BR2/OR2 - ELIC EPIC bank @ 0xFE008000
+ *
+ * AM=0xFFFF8 ATM=0 CSNT/SAM=1 ACS/G5LA/G5LS=3 BIH=1 SCY=2 SETA=0 TRLX=1 EHTR=1
+ */
+#define ELIC_EPIC_BASE 0xFE008000
+#define ELIC_EPIC_OR_AM 0xFFFF8000
+#define ELIC_EPIC_TIMING (OR_SCY_2_CLK | OR_TRLX | OR_EHTR)
+
+#define CFG_OR2 (ELIC_EPIC_OR_AM | OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \
+ ELIC_EPIC_TIMING)
+#define CFG_BR2 ((ELIC_EPIC_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
+
+/*
+ * BR3/OR3: SDRAM
+ *
+ * Multiplexed addresses, GPL5 output to GPL5_A (don't care)
+ */
+#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */
+#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
+#define SDRAM_TIMING OR_SCY_0_CLK /* SDRAM-Timing */
+
+#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */
+
+#define CFG_OR3_PRELIM (SDRAM_PRELIM_OR_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING )
+#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V )
+
+/*
+ * BR4/OR4 - HDLC Address
+ *
+ * AM=0xFFFF8 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=0 BIH=1 SCY=1 SETA=0 TRLX=0 EHTR=0
+ */
+#define HDLC_ADDR_BASE 0xFE108000 /* HDLC Address area */
+#define HDLC_ADDR_OR_AM 0xFFFF8000
+#define HDLC_ADDR_TIMING OR_SCY_1_CLK
+
+#define CFG_OR4 (HDLC_ADDR_OR_AM | OR_BI | HDLC_ADDR_TIMING)
+#define CFG_BR4 ((HDLC_ADDR_BASE & BR_BA_MSK) | BR_PS_8 | BR_WP | BR_V )
+
+/*
+ * BR5/OR5: SHARC ADSP-2165L
+ *
+ * AM=0xFFC00 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=3 BIH=1 SCY=0 SETA=0 TRLX=0 EHTR=0
+ */
+#define SHARC_BASE 0xFE400000
+#define SHARC_OR_AM 0xFFC00000
+#define SHARC_TIMING OR_SCY_0_CLK
+
+#define CFG_OR5 (SHARC_OR_AM | OR_ACS_DIV2 | OR_BI | SHARC_TIMING )
+#define CFG_BR5 ((SHARC_BASE & BR_BA_MSK) | BR_PS_32 | BR_MS_UPMA | BR_V )
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTB 204
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+
+#if defined (CONFIG_IVML24_16M)
+# define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+#elif defined (CONFIG_IVML24_32M)
+# define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+#elif defined (CONFIG_IVML24_64M)
+# define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV8 /* setting for 1 bank */
+#endif
+
+
+/*
+ * MBMR settings for SDRAM
+ */
+
+#if defined (CONFIG_IVML24_16M)
+ /* 8 column SDRAM */
+# define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \
+ MAMR_AMB_TYPE_0 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A11 | \
+ MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X)
+#elif defined (CONFIG_IVML24_32M)
+/* 128 MBit SDRAM */
+# define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \
+ MAMR_AMB_TYPE_1 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A10 | \
+ MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X)
+#elif defined (CONFIG_IVML24_64M)
+/* 128 MBit SDRAM */
+# define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \
+ MAMR_AMB_TYPE_1 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A10 | \
+ MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X)
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
+#define CONFIG_IVMS8 1 /* ...on a IVMS8 board */
+
+#if defined (CONFIG_IVMS8_16M)
+# define CONFIG_IDENT_STRING " IVMS8"
+#elif defined (CONFIG_IVMS8_32M)
+# define CONFIG_IDENT_STRING " IVMS8_128"
+#elif defined (CONFIG_IVMS8_64M)
+# define CONFIG_IDENT_STRING " IVMS8_256"
+#endif
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+#define CONFIG_8xx_GCLK_FREQ 50331648
+
+#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
+
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
+
+#define CONFIG_BOOTARGS "root=/dev/nfs rw " \
+ "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \
+ "nfsaddrs=10.0.0.99:10.0.0.2"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_IDE)
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_BOOTP_MASK \
+ ((CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) & ~CONFIG_BOOTP_GATEWAY)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x00100000 /* default load address */
+
+#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
+
+#define CFG_PB_SDRAM_CLKE 0x00008000 /* PB 16 */
+#define CFG_PB_ETH_POWERDOWN 0x00010000 /* PB 15 */
+#define CFG_PB_IDE_MOTOR 0x00020000 /* PB 14 */
+
+#define CFG_PC_ETH_RESET ((ushort)0x0010) /* PC 11 */
+#define CFG_PC_IDE_RESET ((ushort)0x0020) /* PC 10 */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFFF00000 /* was: 0xFF000000 */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#if defined (CONFIG_IVMS8_16M)
+# define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#elif defined (CONFIG_IVMS8_32M)
+# define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */
+#elif defined (CONFIG_IVMS8_64M)
+# define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */
+#endif
+
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFF000000
+#ifdef DEBUG
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#endif
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x7A000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+# if defined (CONFIG_IVMS8_16M)
+# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+# elif defined (CONFIG_IVMS8_32M)
+# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWP)
+# elif defined (CONFIG_IVMS8_64M)
+# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWP)
+# endif
+#else
+# define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+/* EARB, DBGC and DBPC are initialised by the HCW */
+/* => 0x000000C0 */
+#define CFG_SIUMCR (SIUMCR_BSC | SIUMCR_GB5E)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit, set PLL multiplication factor !
+ */
+/* 0x00B0C0C0 */
+#define CFG_PLPRCR \
+ ( (11 << PLPRCR_MF_SHIFT) | \
+ PLPRCR_SPLSS | PLPRCR_TEXPS | /*PLPRCR_TMIST|*/ \
+ /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \
+ PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \
+ )
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+/* 0x01800014 */
+#define CFG_SCCR (SCCR_COM01 | /*SCCR_TBS|*/ \
+ SCCR_RTDIV | SCCR_RTSEL | \
+ /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \
+ SCCR_EBDF00 | SCCR_DFSYNC00 | \
+ SCCR_DFBRG00 | SCCR_DFNL000 | \
+ SCCR_DFNH000 | SCCR_DFLCD101 | \
+ SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+/* 0x00C3 */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration Register 19-4
+ *-----------------------------------------------------------------------
+ */
+/* TIMEP=2 */
+#define CFG_RCCR 0x0200
+
+/*-----------------------------------------------------------------------
+ * RMDS - RISC Microcode Development Support Control Register
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RMDS 0
+
+/*-----------------------------------------------------------------------
+ *
+ * Interrupt Levels
+ *-----------------------------------------------------------------------
+ */
+#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */
+#define CONFIG_IDE_RESET 1 /* reset for ide supported */
+
+#define CFG_IDE_MAXBUS 1 /* The IVMS8 has only 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* ... and only 1 IDE device */
+
+#define CFG_ATA_BASE_ADDR 0xFE100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#undef CFG_ATA_IDE1_OFFSET /* only one IDE bus available */
+
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define CFG_DER 0x2002000F*/
+#define CFG_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0 and OR0 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0xFF000000 /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+/* EPROMs are 512kb */
+#define CFG_REMAP_OR_AM 0xFFF80000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xFFF80000 /* OR addr mask */
+
+/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH (/* OR_CSNT_SAM | */ OR_ACS_DIV4 | OR_BI | \
+ OR_SCY_5_CLK | OR_EHTR)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+/* 16 bit, bank valid */
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
+
+/*
+ * BR1/OR1 - ELIC SACCO bank @ 0xFE000000
+ *
+ * AM=0xFFFF8 ATM=0 CSNT/SAM=1 ACS/G5LA/G5LS=3 BIH=1 SCY=2 SETA=0 TRLX=1 EHTR=1
+ */
+#define ELIC_SACCO_BASE 0xFE000000
+#define ELIC_SACCO_OR_AM 0xFFFF8000
+#define ELIC_SACCO_TIMING 0x00000F26
+
+#define CFG_OR1 (ELIC_SACCO_OR_AM | ELIC_SACCO_TIMING)
+#define CFG_BR1 ((ELIC_SACCO_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
+
+/*
+ * BR2/OR2 - ELIC EPIC bank @ 0xFE008000
+ *
+ * AM=0xFFFF8 ATM=0 CSNT/SAM=1 ACS/G5LA/G5LS=3 BIH=1 SCY=2 SETA=0 TRLX=1 EHTR=1
+ */
+#define ELIC_EPIC_BASE 0xFE008000
+#define ELIC_EPIC_OR_AM 0xFFFF8000
+#define ELIC_EPIC_TIMING 0x00000F26
+
+#define CFG_OR2 (ELIC_EPIC_OR_AM | ELIC_EPIC_TIMING)
+#define CFG_BR2 ((ELIC_EPIC_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
+
+/*
+ * BR3/OR3: SDRAM
+ *
+ * Multiplexed addresses, GPL5 output to GPL5_A (don't care)
+ */
+#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */
+#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
+#define SDRAM_TIMING 0x00000A00 /* SDRAM-Timing */
+
+#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */
+
+#define CFG_OR3_PRELIM (SDRAM_PRELIM_OR_AM | SDRAM_TIMING )
+#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V )
+
+/*
+ * BR4/OR4: not used
+ */
+
+/*
+ * BR5/OR5: SHARC ADSP-2165L
+ *
+ * AM=0xFFC00 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=3 BIH=1 SCY=0 SETA=0 TRLX=0 EHTR=0
+ */
+#define SHARC_BASE 0xFE400000
+#define SHARC_OR_AM 0xFFC00000
+#define SHARC_TIMING 0x00000700
+
+#define CFG_OR5 (SHARC_OR_AM | SHARC_TIMING )
+#define CFG_BR5 ((SHARC_BASE & BR_BA_MSK) | BR_PS_32 | BR_MS_UPMA | BR_V )
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTB 204
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#if defined (CONFIG_IVMS8_16M)
+ #define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+#elif defined (CONFIG_IVMS8_32M)
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+#elif defined (CONFIG_IVMS8_64M)
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV8 /* setting for 1 bank */
+#endif
+
+
+/*
+ * MBMR settings for SDRAM
+ */
+
+#if defined (CONFIG_IVMS8_16M)
+ /* 8 column SDRAM */
+# define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \
+ MAMR_AMB_TYPE_0 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A11 | \
+ MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X)
+#elif defined (CONFIG_IVMS8_32M)
+/* 128 MBit SDRAM */
+#define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \
+ MAMR_AMB_TYPE_1 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A10 | \
+ MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X)
+#elif defined (CONFIG_IVMS8_64M)
+/* 128 MBit SDRAM */
+#define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \
+ MAMR_AMB_TYPE_1 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A10 | \
+ MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X)
+
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
--- /dev/null
+ /*
+ * A collection of structures, addresses, and values associated with
+ * the Motorola 860T MBX board.
+ * Copied from the FADS stuff, which was originally copied from the MBX stuff!
+ * Magnus Damm added defines for 8xxrom and extended bd_info.
+ * Helmut Buchsbaum added bitvalues for BCSRx
+ * Rob Taylor coverted it back to MBX
+ *
+ * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ */
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#include <mpc8xx_irq.h>
+
+#define CONFIG_MPC860 1
+#define CONFIG_MPC860T 1
+#define CONFIG_MBX 1
+
+#define CONFIG_8xx_CPUCLOCK 40
+#define CONFIG_8xx_BUSCLOCK (CONFIG_8xx_CPUCLOCK)
+#define TARGET_SYSTEM_FREQUENCY 40
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#define CONFIG_BAUDRATE 9600
+
+#define MPC8XX_FACT 10 /* Multiply by 10 */
+#define MPC8XX_XIN 40000000 /* 50 MHz in */
+#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#if 1
+#define CONFIG_8xx_BOOTDELAY -1 /* autoboot disabled */
+#define CONFIG_8xx_TFTP_MODE
+#else
+#define CONFIG_8xx_BOOTDELAY 5 /* autoboot after 5 seconds */
+#undef CONFIG_8xx_TFTP_MODE
+#endif
+
+#define CONFIG_DRAM_SPEED (CONFIG_8xx_BUSCLOCK) /* MHz */
+#define CONFIG_BOOTCOMMAND "bootm FE020000" /* autoboot command */
+#define CONFIG_BOOTARGS " "
+/*
+ * Miscellaneous configurable options
+ */
+#undef CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT ":>" /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0800000 /* 4 ... 8 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFFA00000
+#define CFG_IMMR_SIZE ((uint)(64 * 1024))
+#define CFG_NVRAM_BASE 0xFA000000 /* NVRAM */
+#define CFG_NVRAM_OR 0xffe00000 /* w/o speed dependent flags!! */
+#define CFG_CSR_BASE 0xFA100000 /* Control/Status Registers */
+#define CFG_PCIMEM_BASE 0x80000000 /* PCI I/O and Memory Spaces */
+#define CFG_PCIMEM_OR 0xA0000108
+#define CFG_PCIBRIDGE_BASE 0xFA210000 /* PCI-Bus Bridge Registers */
+#define CFG_PCIBRIDGE_OR 0xFFFF0108
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2f00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_VPD_SIZE 256 /* size in bytes reserved for vpd buffer */
+#define CFG_INIT_VPD_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_VPD_SIZE)
+#define CFG_INIT_SP_OFFSET (CFG_INIT_VPD_OFFSET-8)
+
+/*-----------------------------------------------------------------------
+ * Offset in DPMEM where we keep the VPD data
+ */
+#define CFG_DPRAMVPD (CFG_INIT_VPD_OFFSET - 0x2000)
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x00000000
+/*0xFE000000*/
+#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_HWINFO_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CFG_HWINFO_LEN)
+#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 4 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+/*-----------------------------------------------------------------------
+ * NVRAM Configuration
+ *
+ * Note: the MBX is special because there is already a firmware on this
+ * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
+ * access the NVRAM at the offset 0x1000.
+ */
+#define CFG_ENV_IS_IN_NVRAM 1 /* turn on NVRAM env feature */
+#define CFG_ENV_ADDR (CFG_NVRAM_BASE + 0x1000)
+#define CFG_ENV_SIZE 0x1000
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit - leave PLL multiplication factor unchanged !
+ */
+#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK (SCCR_RTDIV | SCCR_RTSEL)
+#define CFG_SCCR SCCR_TBS
+
+ /*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0
+
+/* Because of the way the 860 starts up and assigns CS0 the
+* entire address space, we have to set the memory controller
+* differently. Normally, you write the option register
+* first, and then enable the chip select by writing the
+* base register. For CS0, you must write the base register
+* first, followed by the option register.
+*/
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+/* the other CS:s are determined by looking at parameters in BCSRx */
+
+
+#define BCSR_ADDR ((uint) 0xFF010000)
+#define BCSR_SIZE ((uint)(64 * 1024))
+
+#define FLASH_BASE0_PRELIM 0xFE000000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0xFF010000 /* FLASH bank #0 */
+
+#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xFFF00000 /* OR addr mask */
+
+/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (0xFF800000 | OR_CSNT_SAM | OR_BI | OR_SCY_3_CLK) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
+#define CFG_BR0_PRELIM (0xFE000000 | BR_V )
+
+/* BCSRx - Board Control and Status Registers */
+#define CFG_OR1_REMAP CFG_OR0_REMAP
+#define CFG_OR1_PRELIM 0xFFC00000 | OR_ACS_DIV4
+#define CFG_BR1_PRELIM (0x00000000 | BR_MS_UPMA | BR_V )
+
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+#define CFG_MAMR 0x13821000
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+
+/* values according to the manual */
+
+
+#define PCMCIA_MEM_ADDR ((uint)0xff020000)
+#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
+
+#define BCSR0 ((uint) (BCSR_ADDR + 00))
+#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
+#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
+#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
+#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
+
+/* FADS bitvalues by Helmut Buchsbaum
+ * see MPC8xxADS User's Manual for a proper description
+ * of the following structures
+ */
+
+#define BCSR0_ERB ((uint)0x80000000)
+#define BCSR0_IP ((uint)0x40000000)
+#define BCSR0_BDIS ((uint)0x10000000)
+#define BCSR0_BPS_MASK ((uint)0x0C000000)
+#define BCSR0_ISB_MASK ((uint)0x01800000)
+#define BCSR0_DBGC_MASK ((uint)0x00600000)
+#define BCSR0_DBPC_MASK ((uint)0x00180000)
+#define BCSR0_EBDF_MASK ((uint)0x00060000)
+
+#define BCSR1_FLASH_EN ((uint)0x80000000)
+#define BCSR1_DRAM_EN ((uint)0x40000000)
+#define BCSR1_ETHEN ((uint)0x20000000)
+#define BCSR1_IRDEN ((uint)0x10000000)
+#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
+#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
+#define BCSR1_BCSR_EN ((uint)0x02000000)
+#define BCSR1_RS232EN_1 ((uint)0x01000000)
+#define BCSR1_PCCEN ((uint)0x00800000)
+#define BCSR1_PCCVCC0 ((uint)0x00400000)
+#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
+#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
+#define BCSR1_RS232EN_2 ((uint)0x00040000)
+#define BCSR1_SDRAM_EN ((uint)0x00020000)
+#define BCSR1_PCCVCC1 ((uint)0x00010000)
+
+#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
+#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
+#define BCSR2_DRAM_PD_SHIFT (23)
+#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
+#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
+
+#define BCSR3_DBID_MASK ((ushort)0x3800)
+#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
+#define BCSR3_BREVNR0 ((ushort)0x0080)
+#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
+#define BCSR3_BREVN1 ((ushort)0x0008)
+#define BCSR3_BREVN2_MASK ((ushort)0x0003)
+
+#define BCSR4_ETHLOOP ((uint)0x80000000)
+#define BCSR4_TFPLDL ((uint)0x40000000)
+#define BCSR4_TPSQEL ((uint)0x20000000)
+#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
+#ifdef CONFIG_MPC823
+#define BCSR4_USB_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860SAR
+#define BCSR4_UTOPIA_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC860SAR */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETH_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC860T */
+#define BCSR4_USB_SPEED ((uint)0x04000000)
+#define BCSR4_VCCO ((uint)0x02000000)
+#define BCSR4_VIDEO_ON ((uint)0x00800000)
+#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
+#define BCSR4_VIDEO_RST ((uint)0x00200000)
+#define BCSR4_MODEM_EN ((uint)0x00100000)
+#define BCSR4_DATA_VOICE ((uint)0x00080000)
+
+#define CONFIG_DRAM_40MHZ 1
+
+#ifdef CONFIG_MPC860T
+
+/* Interrupt level assignments.
+*/
+#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
+
+#endif /* CONFIG_MPC860T */
+
+/* We don't use the 8259.
+*/
+#define NR_8259_INTS 0
+
+/* Machine type
+*/
+#define _MACH_8xx (_MACH_fads)
+
+/*
+ * MPC8xx CPM Options
+ */
+#define CONFIG_SCC_ENET 1
+#define CONFIG_SCC1_ENET 1
+#define CONFIG_FEC_ENET 1
+#undef CONFIG_CPM_IIC
+#undef CONFIG_UCODE_PATCH
+
+
+#define CONFIG_DISK_SPINUP_TIME 1000000
+
+
+/* PCMCIA configuration */
+
+#define PCMCIA_MAX_SLOTS 2
+
+#ifdef CONFIG_MPC860
+#define PCMCIA_SLOT_A 1
+#endif
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef CFG_RAMBOOT
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */
+#define CONFIG_PM826 1 /* ...on a PM8260 module */
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+/* enable I2C and select the hardware/software driver */
+#undef CONFIG_HARD_I2C
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+# define CFG_I2C_SPEED 50000
+# define CFG_I2C_SLAVE 0xFE
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE (iop->pdir |= 0x00010000)
+#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
+#define I2C_READ ((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
+ else iop->pdat &= ~0x00010000
+#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
+ else iop->pdat &= ~0x00020000
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+
+#define CONFIG_RTC_PCF8563
+#define CFG_I2C_RTC_ADDR 0x51
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#define CONFIG_CONS_ON_SMC /* define if console on SMC */
+#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else*/
+#define CONFIG_CONS_INDEX 2 /* which serial channel for console */
+
+/*
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ */
+#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
+#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
+
+#if (CONFIG_ETHER_INDEX == 1)
+/*
+ * - Rx-CLK is CLK11
+ * - Tx-CLK is CLK10
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
+# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10)
+# define CFG_CPMFCR_RAMTYPE 0
+# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+#endif /* CONFIG_ETHER_INDEX */
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#define CONFIG_8260_CLKIN 64000000 /* in Hz */
+
+#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
+#define CONFIG_BAUDRATE 230400
+#else
+#define CONFIG_BAUDRATE 9600
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_BEDBUG | \
+ CFG_CMD_DATE | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DOC)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Disk-On-Chip configuration
+ */
+
+#define CFG_DOC_SHORT_TIMEOUT
+#define CFG_MAX_DOC_DEVICE 1 /* Max number of DOC devices */
+
+#define CFG_DOC_SUPPORT_2000
+#define CFG_DOC_SUPPORT_MILLENNIUM
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Flash and Boot ROM mapping
+ */
+
+#define CFG_BOOTROM_BASE 0x60000000
+#define CFG_BOOTROM_SIZE 0x00080000
+#define CFG_FLASH0_BASE 0x40000000
+#define CFG_FLASH0_SIZE 0x02000000
+#define CFG_DOC_BASE 0x60000000
+#define CFG_DOC_SIZE 0x00100000
+
+
+/* Flash bank size (for preliminary settings)
+ */
+#define CFG_FLASH_SIZE CFG_FLASH0_SIZE
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
+#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+#if 0
+/* Start port with environment in flash; switch to EEPROM later */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (CFG_FLASH_BASE+0x40000)
+#define CFG_ENV_SIZE 0x40000
+#define CFG_ENV_SECT_SIZE 0x40000
+#else
+/* Final version: environment in EEPROM */
+#define CFG_ENV_IS_IN_EEPROM 1
+#define CFG_I2C_EEPROM_ADDR 0x58
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+#define CFG_ENV_OFFSET 0
+#define CFG_ENV_SIZE 2048
+#endif
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * if you change bits in the HRCW, you must also change the CFG_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ */
+#if defined(CONFIG_BOOT_ROM)
+#define CFG_HRCW_MASTER (HRCW_BPS01 | HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
+#else
+#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
+#endif
+
+/* no slaves so just fill with zeros */
+#define CFG_HRCW_SLAVE1 0
+#define CFG_HRCW_SLAVE2 0
+#define CFG_HRCW_SLAVE3 0
+#define CFG_HRCW_SLAVE4 0
+#define CFG_HRCW_SLAVE5 0
+#define CFG_HRCW_SLAVE6 0
+#define CFG_HRCW_SLAVE7 0
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ *
+ * 60x SDRAM is mapped at CFG_SDRAM_BASE, local SDRAM
+ * is mapped at SDRAM_BASE2_PRELIM.
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE CFG_FLASH0_BASE
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+# define CFG_RAMBOOT
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers 2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
+ HID0_IFEM|HID0_ABE)
+#define CFG_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE)
+#define CFG_HID2 0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CFG_RMR RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration 4-25
+ *-----------------------------------------------------------------------
+ */
+
+#define BCR_APD01 0x10000000
+#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 4-31
+ *-----------------------------------------------------------------------
+ */
+#if 0
+#define CFG_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_CS10PC01)
+#else
+#define CFG_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10)
+#endif
+
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control 4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control 9-8
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SCCR (SCCR_DFBRG01)
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration 13-7
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR 0
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus Machine PortSz Device
+ * ---- --- ------- ------ ------
+ * 0 60x GPCM 64 bit FLASH
+ * 1 60x SDRAM 64 bit SDRAM
+ * 2 Local SDRAM 32 bit SDRAM
+ *
+ */
+
+ /* Initialize SDRAM on local bus
+ */
+#define CFG_INIT_LOCAL_SDRAM
+
+
+/* Minimum mask to separate preliminary
+ * address ranges for CS[0:2]
+ */
+#define CFG_MIN_AM_MASK 0xC0000000
+
+#define CFG_MPTPR 0x1F00
+
+#define CFG_MRS_OFFS 0x00000000
+
+
+#if defined(CONFIG_BOOT_ROM)
+/*
+ * Bank 0 - Boot ROM (8 bit wide)
+ */
+#define CFG_BR0_PRELIM ((CFG_BOOTROM_BASE & BRx_BA_MSK)|\
+ BRx_PS_8 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_BOOTROM_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_3_CLK |\
+ ORxG_EHTR |\
+ ORxG_TRLX)
+
+/*
+ * Bank 1 - Flash (64 bit wide)
+ */
+#define CFG_BR1_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_3_CLK |\
+ ORxG_EHTR |\
+ ORxG_TRLX)
+
+#else /* ! CONFIG_BOOT_ROM */
+
+/*
+ * Bank 0 - Flash (64 bit wide)
+ */
+#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_FLASH_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_3_CLK |\
+ ORxG_EHTR |\
+ ORxG_TRLX)
+
+/*
+ * Bank 1 - Disk-On-Chip
+ */
+#define CFG_BR1_PRELIM ((CFG_DOC_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR1_PRELIM (P2SZ_TO_AM(CFG_DOC_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_3_CLK |\
+ ORxG_EHTR |\
+ ORxG_TRLX)
+
+#endif /* CONFIG_BOOT_ROM */
+
+/* Bank 2 - SDRAM
+ */
+#define CFG_PSRT 0x0F
+#ifndef CFG_RAMBOOT
+#define CFG_BR2_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_SDRAM_P |\
+ BRx_V)
+
+ /* SDRAM initialization values for 8-column chips
+ */
+#define CFG_OR2_8COL (CFG_MIN_AM_MASK |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI0_A9 |\
+ ORxS_NUMR_12)
+
+#define CFG_PSDMR_8COL (PSDMR_SDAM_A13_IS_A5 |\
+ PSDMR_BSMA_A14_A16 |\
+ PSDMR_SDA10_PBI0_A10 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_1W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_1C |\
+ PSDMR_CL_2)
+
+ /* SDRAM initialization values for 9-column chips
+ */
+#define CFG_OR2_9COL (CFG_MIN_AM_MASK |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI0_A7 |\
+ ORxS_NUMR_13)
+
+#define CFG_PSDMR_9COL (PSDMR_SDAM_A14_IS_A5 |\
+ PSDMR_BSMA_A13_A15 |\
+ PSDMR_SDA10_PBI0_A9 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_1W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_1C |\
+ PSDMR_CL_2)
+
+#define CFG_OR2_PRELIM CFG_OR2_9COL
+#define CFG_PSDMR CFG_PSDMR_9COL
+
+#endif /* CFG_RAMBOOT */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */
+#define CONFIG_TQM8260 200 /* ...on a TQM8260 module Rev.200 */
+#define CONFIG_SCM 1 /* ...on a System Controller Module */
+
+#if (CONFIG_TQM8260 <= 100)
+# error "TQM8260 module revison not supported"
+#endif
+
+/* We use a TQM8260 module with a 300MHz CPU */
+#define CONFIG_300MHz
+
+/* Define 60x busmode only if your TQM8260 has L2 cache! */
+#ifdef CONFIG_L2_CACHE
+# define CONFIG_BUSMODE_60x 1 /* bus mode: 60x */
+#else
+# undef CONFIG_BUSMODE_60x /* bus mode: 8260 */
+#endif
+
+/* The board with 300MHz CPU doesn't have L2 cache, but works in 60x bus mode */
+#ifdef CONFIG_300MHz
+# define CONFIG_BUSMODE_60x
+#endif
+
+#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+/* enable I2C and select the hardware/software driver */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+
+#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE (iop->pdir |= 0x00010000)
+#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
+#define I2C_READ ((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
+ else iop->pdat &= ~0x00010000
+#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
+ else iop->pdat &= ~0x00020000
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CFG_I2C_EEPROM_ADDR 0x50
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+#define CONFIG_I2C_X
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#define CONFIG_CONS_ON_SMC /* define if console on SMC */
+#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else*/
+#ifdef CONFIG_82xx_CONS_SMC1
+#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
+#endif
+#ifdef CONFIG_82xx_CONS_SMC2
+#define CONFIG_CONS_INDEX 2 /* which serial channel for console */
+#endif
+
+#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */
+#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */
+#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9 */
+
+/*
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ *
+ * (On TQM8260 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the
+ * X.29 connector, and FCC2 is hardwired to the X.1 connector)
+ */
+#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
+#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
+
+#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1)
+
+/*
+ * - Rx-CLK is CLK12
+ * - Tx-CLK is CLK11
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
+# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK12|CMXFCR_TF1CS_CLK11)
+# define CFG_CPMFCR_RAMTYPE 0
+# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3)
+
+/*
+ * - Rx-CLK is CLK15
+ * - Tx-CLK is CLK16
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
+# define CFG_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
+# define CFG_CPMFCR_RAMTYPE 0
+# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
+
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#ifndef CONFIG_300MHz
+#define CONFIG_8260_CLKIN 66666666 /* in Hz */
+#else
+#define CONFIG_8260_CLKIN 83333000 /* in Hz */
+#endif
+
+#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
+#define CONFIG_BAUDRATE 230400
+#else
+#define CONFIG_BAUDRATE 115200
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_I2C | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_BSP)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */
+
+#define CONFIG_MISC_INIT_R /* have misc_init_r() function */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+
+/* What should the base address of the main FLASH be and how big is
+ * it (in MBytes)? This must contain TEXT_BASE from board/tqm8260/config.mk
+ * The main FLASH is whichever is connected to *CS0.
+ */
+#define CFG_FLASH0_BASE 0x40000000
+#define CFG_FLASH1_BASE 0x60000000
+#define CFG_FLASH0_SIZE 32
+#define CFG_FLASH1_SIZE 32
+
+/* Flash bank size (for preliminary settings)
+ */
+#define CFG_FLASH_SIZE CFG_FLASH0_SIZE
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
+#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+#if 0
+/* Start port with environment in flash; switch to EEPROM later */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (CFG_FLASH_BASE+0x40000)
+#define CFG_ENV_SIZE 0x40000
+#define CFG_ENV_SECT_SIZE 0x40000
+#else
+/* Final version: environment in EEPROM */
+#define CFG_ENV_IS_IN_EEPROM 1
+#define CFG_ENV_OFFSET 0
+#define CFG_ENV_SIZE 2048
+#endif
+
+/*-----------------------------------------------------------------------
+ * Hardware Information Block
+ */
+#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
+#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
+#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * if you change bits in the HRCW, you must also change the CFG_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ */
+#if defined(CONFIG_266MHz)
+#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \
+ HRCW_MODCK_H0111)
+#elif defined(CONFIG_300MHz)
+#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \
+ HRCW_MODCK_H0110)
+#else
+#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
+#endif
+
+/* no slaves so just fill with zeros */
+#define CFG_HRCW_SLAVE1 0
+#define CFG_HRCW_SLAVE2 0
+#define CFG_HRCW_SLAVE3 0
+#define CFG_HRCW_SLAVE4 0
+#define CFG_HRCW_SLAVE5 0
+#define CFG_HRCW_SLAVE6 0
+#define CFG_HRCW_SLAVE7 0
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ *
+ * 60x SDRAM is mapped at CFG_SDRAM_BASE, local SDRAM
+ * is mapped at SDRAM_BASE2_PRELIM.
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE CFG_FLASH0_BASE
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+
+/*-----------------------------------------------------------------------
+ * Hardware Information Block
+ */
+#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
+#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
+#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers 2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
+ HID0_IFEM|HID0_ABE)
+#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE)
+#define CFG_HID2 0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CFG_RMR RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration 4-25
+ *-----------------------------------------------------------------------
+ */
+#ifdef CONFIG_BUSMODE_60x
+#define CFG_BCR (BCR_EBM|BCR_L2C|BCR_LETM|\
+ BCR_NPQM0|BCR_NPQM1|BCR_NPQM2) /* 60x mode */
+#else
+#define BCR_APD01 0x10000000
+#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 4-31
+ *-----------------------------------------------------------------------
+ */
+#if 0
+#define CFG_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10)
+#else
+#define CFG_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10)
+#endif
+
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control 4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control 9-8
+ *-----------------------------------------------------------------------
+ * Ensure DFBRG is Divide by 16
+ */
+#define CFG_SCCR 0
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration 13-7
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR 0
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus Machine PortSz Device
+ * ---- --- ------- ------ ------
+ * 0 60x GPCM 64 bit FLASH
+ * 1 60x SDRAM 64 bit SDRAM
+ * 2 Local SDRAM 32 bit SDRAM
+ *
+ */
+
+ /* Initialize SDRAM on local bus
+ */
+#define CFG_INIT_LOCAL_SDRAM
+
+#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
+
+/* Minimum mask to separate preliminary
+ * address ranges for CS[0:2]
+ */
+#define CFG_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */
+#define CFG_LOCAL_SDRAM_LIMIT (128<<20) /* less than 128 MB */
+
+#define CFG_MPTPR 0x4000
+
+/*-----------------------------------------------------------------------------
+ * Address for Mode Register Set (MRS) command
+ *-----------------------------------------------------------------------------
+ * In fact, the address is rather configuration data presented to the SDRAM on
+ * its address lines. Because the address lines may be mux'ed externally either
+ * for 8 column or 9 column devices, some bits appear twice in the 8260's
+ * address:
+ *
+ * | (RFU) | (RFU) | WBL | TM | CL | BT | Burst Length |
+ * | BA1 BA0 | A12 : A10 | A9 | A8 A7 | A6 : A4 | A3 | A2 : A0 |
+ * 8 columns mux'ing: | A9 | A10 A21 | A22 : A24 | A25 | A26 : A28 |
+ * 9 columns mux'ing: | A8 | A20 A21 | A22 : A24 | A25 | A26 : A28 |
+ * Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 |
+ *-----------------------------------------------------------------------------
+ */
+#define CFG_MRS_OFFS 0x00000110
+
+
+/* Bank 0 - FLASH
+ */
+#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_3_CLK |\
+ ORxG_EHTR |\
+ ORxG_TRLX)
+
+ /* SDRAM on TQM8260 can have either 8 or 9 columns.
+ * The number affects configuration values.
+ */
+
+/* Bank 1 - 60x bus SDRAM
+ */
+#define CFG_PSRT 0x20
+#define CFG_LSRT 0x20
+#ifndef CFG_RAMBOOT
+#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_SDRAM_P |\
+ BRx_V)
+
+#define CFG_OR1_PRELIM CFG_OR1_8COL
+
+
+ /* SDRAM initialization values for 8-column chips
+ */
+#define CFG_OR1_8COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A7 |\
+ ORxS_NUMR_12)
+
+#define CFG_PSDMR_8COL (PSDMR_PBI |\
+ PSDMR_SDAM_A15_IS_A5 |\
+ PSDMR_BSMA_A12_A14 |\
+ PSDMR_SDA10_PBI1_A8 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_2C |\
+ PSDMR_EAMUX |\
+ PSDMR_CL_2)
+
+ /* SDRAM initialization values for 9-column chips
+ */
+#define CFG_OR1_9COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A5 |\
+ ORxS_NUMR_13)
+
+#define CFG_PSDMR_9COL (PSDMR_PBI |\
+ PSDMR_SDAM_A16_IS_A5 |\
+ PSDMR_BSMA_A12_A14 |\
+ PSDMR_SDA10_PBI1_A7 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_2C |\
+ PSDMR_EAMUX |\
+ PSDMR_CL_2)
+
+/* Bank 2 - Local bus SDRAM
+ */
+#ifdef CFG_INIT_LOCAL_SDRAM
+#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BRx_BA_MSK) |\
+ BRx_PS_32 |\
+ BRx_MS_SDRAM_L |\
+ BRx_V)
+
+#define CFG_OR2_PRELIM CFG_OR2_8COL
+
+#define SDRAM_BASE2_PRELIM 0x80000000
+
+ /* SDRAM initialization values for 8-column chips
+ */
+#define CFG_OR2_8COL ((~(CFG_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A8 |\
+ ORxS_NUMR_12)
+
+#define CFG_LSDMR_8COL (PSDMR_PBI |\
+ PSDMR_SDAM_A15_IS_A5 |\
+ PSDMR_BSMA_A13_A15 |\
+ PSDMR_SDA10_PBI1_A9 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_BL |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_2C |\
+ PSDMR_CL_2)
+
+ /* SDRAM initialization values for 9-column chips
+ */
+#define CFG_OR2_9COL ((~(CFG_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A6 |\
+ ORxS_NUMR_13)
+
+#define CFG_LSDMR_9COL (PSDMR_PBI |\
+ PSDMR_SDAM_A16_IS_A5 |\
+ PSDMR_BSMA_A13_A15 |\
+ PSDMR_SDA10_PBI1_A8 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_BL |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_2C |\
+ PSDMR_CL_2)
+
+#endif /* CFG_INIT_LOCAL_SDRAM */
+
+#endif /* CFG_RAMBOOT */
+
+#define CFG_CAN0_BASE 0xc0000000
+#define CFG_CAN1_BASE 0xc0008000
+#define CFG_FIOX_BASE 0xc0010000
+#define CFG_FDOHM_BASE 0xc0018000
+#define CFG_EXTPROM_BASE 0xc2000000
+
+#define CFG_CAN_SIZE 0x00000100
+#define CFG_FIOX_SIZE 0x00000020
+#define CFG_FDOHM_SIZE 0x00002000
+#define CFG_EXTPROM_BANK_SIZE 0x01000000
+
+#define EXT_EEPROM_MAX_FLASH_BANKS 0x02
+
+/* CS3 - CAN 0
+ */
+#define CFG_CAN0_BR3 ((CFG_CAN0_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 |\
+ BRx_MS_UPMA |\
+ BRx_V)
+
+#define CFG_CAN0_OR3 (P2SZ_TO_AM(CFG_CAN_SIZE) |\
+ ORxU_BI |\
+ ORxU_EHTR_4IDLE)
+
+/* CS4 - CAN 1
+ */
+#define CFG_CAN1_BR4 ((CFG_CAN1_BASE & BRx_BA_MSK) |\
+ BRx_PS_8 |\
+ BRx_MS_UPMA |\
+ BRx_V)
+
+#define CFG_CAN1_OR4 (P2SZ_TO_AM(CFG_CAN_SIZE) |\
+ ORxU_BI |\
+ ORxU_EHTR_4IDLE)
+
+/* CS5 - Extended PROM (16MB optional)
+ */
+#define CFG_EXTPROM_BR5 ((CFG_EXTPROM_BASE & BRx_BA_MSK)|\
+ BRx_PS_32 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_EXTPROM_OR5 (P2SZ_TO_AM(CFG_EXTPROM_BANK_SIZE)|\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV4 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_TRLX)
+
+/* CS6 - Extended PROM (16MB optional)
+ */
+#define CFG_EXTPROM_BR6 (((CFG_EXTPROM_BASE + \
+ CFG_EXTPROM_BANK_SIZE) & BRx_BA_MSK)|\
+ BRx_PS_32 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_EXTPROM_OR6 (P2SZ_TO_AM(CFG_EXTPROM_BANK_SIZE)|\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV4 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_TRLX)
+
+/* CS7 - FPGA FIOX: Glue Logic
+ */
+#define CFG_FIOX_BR7 ((CFG_FIOX_BASE & BRx_BA_MSK) |\
+ BRx_PS_32 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_FIOX_OR7 (P2SZ_TO_AM(CFG_FIOX_SIZE) |\
+ ORxG_ACS_DIV4 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_TRLX)
+
+/* CS8 - FPGA DOH Master
+ */
+#define CFG_FDOHM_BR8 ((CFG_FDOHM_BASE & BRx_BA_MSK) |\
+ BRx_PS_16 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_FDOHM_OR8 (P2SZ_TO_AM(CFG_FDOHM_SIZE) |\
+ ORxG_ACS_DIV4 |\
+ ORxG_SCY_5_CLK |\
+ ORxG_TRLX)
+
+
+/* FPGA configuration */
+#define CFG_PD_FIOX_PROG (1 << (31- 5)) /* PD 5 */
+#define CFG_PD_FIOX_DONE (1 << (31-28)) /* PD 28 */
+#define CFG_PD_FIOX_INIT (1 << (31-29)) /* PD 29 */
+
+#define CFG_PD_FDOHM_PROG (1 << (31- 4)) /* PD 4 */
+#define CFG_PD_FDOHM_DONE (1 << (31-26)) /* PD 26 */
+#define CFG_PD_FDOHM_INIT (1 << (31-27)) /* PD 27 */
+
+
+#endif /* __CONFIG_H */
+
--- /dev/null
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
+#define CONFIG_SPD823TS 1 /* ...on a SPD823TS board */
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 115200
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
+
+#define CONFIG_BOOTARGS "root=/dev/nfs rw " \
+ "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \
+ "nfsaddrs=10.0.0.99:10.0.0.2"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_COMMANDS \
+((CONFIG_CMD_DFL & ~(CFG_CMD_FLASH)) | CFG_CMD_IDE) /* no Flash, but IDE */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*----------------------------------------------------------------------*/
+#define CONFIG_ETHADDR 00:D0:93:00:01:CB
+#define CONFIG_IPADDR 10.0.0.98
+#define CONFIG_SERVERIP 10.0.0.1
+#undef CONFIG_BOOTCOMMAND
+#define CONFIG_BOOTCOMMAND "tftp 200000 pImage;bootm 200000"
+/*----------------------------------------------------------------------*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x00100000 /* default load address */
+
+#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
+
+#define CFG_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFFF00000 /* was: 0xFF000000 */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFF000000
+#ifdef DEBUG
+#define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#endif
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 0 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 0 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 0 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 0 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x0800 /* Total Size of Environment Sector */
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+/* 0x00000040 */
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC00 | SIUMCR_GB5E)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit, set PLL multiplication factor !
+ */
+/* 0x00b0c0c0 */
+#define CFG_PLPRCR \
+ ( (11 << PLPRCR_MF_SHIFT) | \
+ PLPRCR_SPLSS | PLPRCR_TEXPS | /*PLPRCR_TMIST|*/ \
+ /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \
+ PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \
+ )
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+/* 0x01800014 */
+#define CFG_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \
+ SCCR_RTDIV | SCCR_RTSEL | \
+ /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \
+ SCCR_EBDF00 | SCCR_DFSYNC00 | \
+ SCCR_DFBRG00 | SCCR_DFNL000 | \
+ SCCR_DFNH000 | SCCR_DFLCD101 | \
+ SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register
+ *-----------------------------------------------------------------------
+ */
+/* 0x00C3 */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration Register
+ *-----------------------------------------------------------------------
+ */
+/* TIMEP=2 */
+#define CFG_RCCR 0x0200
+
+/*-----------------------------------------------------------------------
+ * RMDS - RISC Microcode Development Support Control Register
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RMDS 0
+
+/*-----------------------------------------------------------------------
+ * SDSR - SDMA Status Register
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SDSR ((u_char)0x83)
+
+/*-----------------------------------------------------------------------
+ * SDMR - SDMA Mask Register
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SDMR ((u_char)0x00)
+
+/*-----------------------------------------------------------------------
+ *
+ * Interrupt Levels
+ *-----------------------------------------------------------------------
+ */
+#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */
+#define CONFIG_IDE_LED 1 /* LED for ide supported */
+#define CONFIG_IDE_RESET 1 /* reset for ide supported */
+
+#define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
+
+#define CFG_ATA_BASE_ADDR 0xFE100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_IDE1_OFFSET 0x0C00
+
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define CFG_DER 0x2002000F*/
+#define CFG_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0xFF000000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0xFF080000 /* FLASH bank #1 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+/* EPROMs are 512kb */
+#define CFG_REMAP_OR_AM 0xFFF80000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xFFF80000 /* OR addr mask */
+
+/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH (/* OR_CSNT_SAM | */ OR_ACS_DIV4 | OR_BI | \
+ OR_SCY_5_CLK | OR_EHTR)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+/* 16 bit, bank valid */
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
+
+#define CFG_OR1_REMAP CFG_OR0_REMAP
+#define CFG_OR1_PRELIM CFG_OR0_PRELIM
+/* 16 bit, bank valid */
+#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
+
+/*
+ * BR2-5 and OR2-5 (SRAM/SDRAM/PER8/SHARC)
+ *
+ */
+#define SRAM_BASE 0xFE200000 /* SRAM bank */
+#define SRAM_OR_AM 0xFFE00000 /* SRAM is 2 MB */
+
+#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */
+#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
+#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */
+
+#define PER8_BASE 0xFE000000 /* PER8 bank */
+#define PER8_OR_AM 0xFFF00000 /* PER8 is 1 MB */
+
+#define SHARC_BASE 0xFE400000 /* SHARC bank */
+#define SHARC_OR_AM 0xFFC00000 /* SHARC is 4 MB */
+
+/* SRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+
+#define CFG_OR_TIMING_SRAM 0x00000D42 /* SRAM-Timing */
+#define CFG_OR2 (SRAM_OR_AM | CFG_OR_TIMING_SRAM )
+#define CFG_BR2 ((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V )
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+
+#define CFG_OR_TIMING_SDRAM 0x00000A00 /* SDRAM-Timing */
+#define CFG_OR3_PRELIM (SDRAM_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V )
+
+#define CFG_OR_TIMING_PER8 0x00000F32 /* PER8-Timing */
+#define CFG_OR4 (PER8_OR_AM | CFG_OR_TIMING_PER8 )
+#define CFG_BR4 ((PER8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
+
+#define CFG_OR_TIMING_SHARC 0x00000700 /* SHARC-Timing */
+#define CFG_OR5 (SHARC_OR_AM | CFG_OR_TIMING_SHARC )
+#define CFG_BR5 ((SHARC_BASE & BR_BA_MSK) | BR_PS_32 | BR_MS_UPMA | BR_V )
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTB 204
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+
+/*
+ * MBMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MBMR_8COL ((CFG_MAMR_PTB << MAMR_PTB_SHIFT) | \
+ MAMR_AMB_TYPE_0 | MAMR_DSB_1_CYCL | MAMR_G0CLB_A11 | \
+ MAMR_RLFB_1X | MAMR_WLFB_1X | MAMR_TLFB_4X)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * Imported from global configuration:
+ * CONFIG_L2_CACHE
+ * CONFIG_266MHz
+ * CONFIG_300MHz
+ */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */
+
+#if 0
+#define CONFIG_TQM8260 100 /* ...on a TQM8260 module Rev.100 */
+#else
+#define CONFIG_TQM8260 200 /* ...on a TQM8260 module Rev.200 */
+#endif
+
+/* Define 60x busmode only if your TQM8260 has L2 cache! */
+#ifdef CONFIG_L2_CACHE
+# define CONFIG_BUSMODE_60x 1 /* bus mode: 60x */
+#else
+# undef CONFIG_BUSMODE_60x /* bus mode: 8260 */
+#endif
+
+/* The board with 300MHz CPU doesn't have L2 cache, but works in 60x bus mode */
+#ifdef CONFIG_300MHz
+# define CONFIG_BUSMODE_60x
+#endif
+
+#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+/* enable I2C and select the hardware/software driver */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+
+/* TQM8260 Rev.100 has the clock and data pins swapped (!!!) on EEPROM */
+#if (CONFIG_TQM8260 <= 100)
+
+#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE (iop->pdir |= 0x00020000)
+#define I2C_TRISTATE (iop->pdir &= ~0x00020000)
+#define I2C_READ ((iop->pdat & 0x00020000) != 0)
+#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00020000; \
+ else iop->pdat &= ~0x00020000
+#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00010000; \
+ else iop->pdat &= ~0x00010000
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#else
+
+#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE (iop->pdir |= 0x00010000)
+#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
+#define I2C_READ ((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
+ else iop->pdat &= ~0x00010000
+#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
+ else iop->pdat &= ~0x00020000
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+#endif
+
+#define CFG_I2C_EEPROM_ADDR 0x50
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+#define CONFIG_I2C_X
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#define CONFIG_CONS_ON_SMC /* define if console on SMC */
+#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else*/
+#ifdef CONFIG_82xx_CONS_SMC1
+#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
+#endif
+#ifdef CONFIG_82xx_CONS_SMC2
+#define CONFIG_CONS_INDEX 2 /* which serial channel for console */
+#endif
+
+#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */
+#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */
+#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9 */
+
+/*
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ *
+ * (On TQM8260 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the
+ * X.29 connector, and FCC2 is hardwired to the X.1 connector)
+ */
+#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
+#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */
+
+#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1)
+
+/*
+ * - RX clk is CLK11
+ * - TX clk is CLK12
+ */
+# define CFG_CMXSCR_VALUE (CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12)
+
+#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
+
+/*
+ * - Rx-CLK is CLK13
+ * - Tx-CLK is CLK14
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+# define CFG_CPMFCR_RAMTYPE 0
+# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
+
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#ifndef CONFIG_300MHz
+#define CONFIG_8260_CLKIN 66666666 /* in Hz */
+#else
+#define CONFIG_8260_CLKIN 83333000 /* in Hz */
+#endif
+
+#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
+#define CONFIG_BAUDRATE 230400
+#else
+#define CONFIG_BAUDRATE 9600
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_I2C | \
+ CFG_CMD_EEPROM)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_RESET_ADDRESS 0xFFFFFFFC /* "bad" address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+
+/* What should the base address of the main FLASH be and how big is
+ * it (in MBytes)? This must contain TEXT_BASE from board/tqm8260/config.mk
+ * The main FLASH is whichever is connected to *CS0.
+ */
+#define CFG_FLASH0_BASE 0x40000000
+#define CFG_FLASH1_BASE 0x60000000
+#define CFG_FLASH0_SIZE 32
+#define CFG_FLASH1_SIZE 32
+
+/* Flash bank size (for preliminary settings)
+ */
+#define CFG_FLASH_SIZE CFG_FLASH0_SIZE
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
+#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+#if 0
+/* Start port with environment in flash; switch to EEPROM later */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (CFG_FLASH_BASE+0x40000)
+#define CFG_ENV_SIZE 0x40000
+#define CFG_ENV_SECT_SIZE 0x40000
+#else
+/* Final version: environment in EEPROM */
+#define CFG_ENV_IS_IN_EEPROM 1
+#define CFG_ENV_OFFSET 0
+#define CFG_ENV_SIZE 2048
+#endif
+
+/*-----------------------------------------------------------------------
+ * Hardware Information Block
+ */
+#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
+#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
+#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * if you change bits in the HRCW, you must also change the CFG_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ */
+#if defined(CONFIG_266MHz)
+#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \
+ HRCW_MODCK_H0111)
+#elif defined(CONFIG_300MHz)
+#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \
+ HRCW_MODCK_H0110)
+#else
+#define CFG_HRCW_MASTER (HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
+#endif
+
+/* no slaves so just fill with zeros */
+#define CFG_HRCW_SLAVE1 0
+#define CFG_HRCW_SLAVE2 0
+#define CFG_HRCW_SLAVE3 0
+#define CFG_HRCW_SLAVE4 0
+#define CFG_HRCW_SLAVE5 0
+#define CFG_HRCW_SLAVE6 0
+#define CFG_HRCW_SLAVE7 0
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data*/
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ *
+ * 60x SDRAM is mapped at CFG_SDRAM_BASE, local SDRAM
+ * is mapped at SDRAM_BASE2_PRELIM.
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE CFG_FLASH0_BASE
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers 2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
+ HID0_IFEM|HID0_ABE)
+#define CFG_HID0_FINAL (HID0_IFEM|HID0_ABE)
+#define CFG_HID2 0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CFG_RMR RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration 4-25
+ *-----------------------------------------------------------------------
+ */
+#ifdef CONFIG_BUSMODE_60x
+#define CFG_BCR (BCR_EBM|BCR_L2C|BCR_LETM|\
+ BCR_NPQM0|BCR_NPQM1|BCR_NPQM2) /* 60x mode */
+#else
+#define BCR_APD01 0x10000000
+#define CFG_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 4-31
+ *-----------------------------------------------------------------------
+ */
+#if 0
+#define CFG_SIUMCR (SIUMCR_DPPC10|SIUMCR_APPC10)
+#else
+#define CFG_SIUMCR (SIUMCR_DPPC00|SIUMCR_APPC10)
+#endif
+
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control 4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control 9-8
+ *-----------------------------------------------------------------------
+ * Ensure DFBRG is Divide by 16
+ */
+#define CFG_SCCR 0
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration 13-7
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR 0
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus Machine PortSz Device
+ * ---- --- ------- ------ ------
+ * 0 60x GPCM 64 bit FLASH
+ * 1 60x SDRAM 64 bit SDRAM
+ * 2 Local SDRAM 32 bit SDRAM
+ *
+ */
+
+ /* Initialize SDRAM on local bus
+ */
+#define CFG_INIT_LOCAL_SDRAM
+
+#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */
+
+/* Minimum mask to separate preliminary
+ * address ranges for CS[0:2]
+ */
+#define CFG_GLOBAL_SDRAM_LIMIT (512<<20) /* less than 512 MB */
+#define CFG_LOCAL_SDRAM_LIMIT (128<<20) /* less than 128 MB */
+
+#define CFG_MPTPR 0x4000
+
+/*-----------------------------------------------------------------------------
+ * Address for Mode Register Set (MRS) command
+ *-----------------------------------------------------------------------------
+ * In fact, the address is rather configuration data presented to the SDRAM on
+ * its address lines. Because the address lines may be mux'ed externally either
+ * for 8 column or 9 column devices, some bits appear twice in the 8260's
+ * address:
+ *
+ * | (RFU) | (RFU) | WBL | TM | CL | BT | Burst Length |
+ * | BA1 BA0 | A12 : A10 | A9 | A8 A7 | A6 : A4 | A3 | A2 : A0 |
+ * 8 columns mux'ing: | A9 | A10 A21 | A22 : A24 | A25 | A26 : A28 |
+ * 9 columns mux'ing: | A8 | A20 A21 | A22 : A24 | A25 | A26 : A28 |
+ * Settings: | 0 | 0 0 | 0 1 0 | 0 | 0 1 0 |
+ *-----------------------------------------------------------------------------
+ */
+#define CFG_MRS_OFFS 0x00000110
+
+
+/* Bank 0 - FLASH
+ */
+#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_GPCM_P |\
+ BRx_V)
+
+#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\
+ ORxG_CSNT |\
+ ORxG_ACS_DIV1 |\
+ ORxG_SCY_3_CLK |\
+ ORxG_EHTR |\
+ ORxG_TRLX)
+
+ /* SDRAM on TQM8260 can have either 8 or 9 columns.
+ * The number affects configuration values.
+ */
+
+/* Bank 1 - 60x bus SDRAM
+ */
+#define CFG_PSRT 0x20
+#define CFG_LSRT 0x20
+#ifndef CFG_RAMBOOT
+#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
+ BRx_PS_64 |\
+ BRx_MS_SDRAM_P |\
+ BRx_V)
+
+#define CFG_OR1_PRELIM CFG_OR1_8COL
+
+
+ /* SDRAM initialization values for 8-column chips
+ */
+#define CFG_OR1_8COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A7 |\
+ ORxS_NUMR_12)
+
+#define CFG_PSDMR_8COL (PSDMR_PBI |\
+ PSDMR_SDAM_A15_IS_A5 |\
+ PSDMR_BSMA_A12_A14 |\
+ PSDMR_SDA10_PBI1_A8 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_2C |\
+ PSDMR_EAMUX |\
+ PSDMR_CL_2)
+
+ /* SDRAM initialization values for 9-column chips
+ */
+#define CFG_OR1_9COL ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A5 |\
+ ORxS_NUMR_13)
+
+#define CFG_PSDMR_9COL (PSDMR_PBI |\
+ PSDMR_SDAM_A16_IS_A5 |\
+ PSDMR_BSMA_A12_A14 |\
+ PSDMR_SDA10_PBI1_A7 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_2C |\
+ PSDMR_EAMUX |\
+ PSDMR_CL_2)
+
+/* Bank 2 - Local bus SDRAM
+ */
+#ifdef CFG_INIT_LOCAL_SDRAM
+#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BRx_BA_MSK) |\
+ BRx_PS_32 |\
+ BRx_MS_SDRAM_L |\
+ BRx_V)
+
+#define CFG_OR2_PRELIM CFG_OR2_8COL
+
+#define SDRAM_BASE2_PRELIM 0x80000000
+
+ /* SDRAM initialization values for 8-column chips
+ */
+#define CFG_OR2_8COL ((~(CFG_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A8 |\
+ ORxS_NUMR_12)
+
+#define CFG_LSDMR_8COL (PSDMR_PBI |\
+ PSDMR_SDAM_A15_IS_A5 |\
+ PSDMR_BSMA_A13_A15 |\
+ PSDMR_SDA10_PBI1_A9 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_BL |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_2C |\
+ PSDMR_CL_2)
+
+ /* SDRAM initialization values for 9-column chips
+ */
+#define CFG_OR2_9COL ((~(CFG_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+ ORxS_BPD_4 |\
+ ORxS_ROWST_PBI1_A6 |\
+ ORxS_NUMR_13)
+
+#define CFG_LSDMR_9COL (PSDMR_PBI |\
+ PSDMR_SDAM_A16_IS_A5 |\
+ PSDMR_BSMA_A13_A15 |\
+ PSDMR_SDA10_PBI1_A8 |\
+ PSDMR_RFRC_7_CLK |\
+ PSDMR_PRETOACT_2W |\
+ PSDMR_ACTTORW_2W |\
+ PSDMR_BL |\
+ PSDMR_LDOTOPRE_1C |\
+ PSDMR_WRC_2C |\
+ PSDMR_CL_2)
+
+#endif /* CFG_INIT_LOCAL_SDRAM */
+
+#endif /* CFG_RAMBOOT */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2000, 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405GP 1 /* This is a PPC405 CPU */
+#define CONFIG_4xx 1 /* ...member of PPC4xx family */
+#define CONFIG_WALNUT405 1 /* ...on a WALNUT405 board */
+
+#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+
+/*#define CFG_ENV_IS_IN_FLASH 1*/ /* use FLASH for environment vars */
+#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
+
+#ifdef CFG_ENV_IS_IN_NVRAM
+#undef CFG_ENV_IS_IN_FLASH
+#else
+#ifdef CFG_ENV_IS_IN_FLASH
+#undef CFG_ENV_IS_IN_NVRAM
+#endif
+#endif
+
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+
+#if 1
+#define CONFIG_BOOTCOMMAND "bootm ffc00000" /* autoboot command */
+#else
+#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
+#endif
+
+/* Size (bytes) of interrupt driven serial port buffer.
+ * Set to 0 to use polling instead of interrupts.
+ * Setting to 0 will also disable RTS/CTS handshaking.
+ */
+#if 0
+#define CONFIG_SERIAL_SOFTWARE_FIFO 4000
+#else
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#endif
+
+#if 0
+#define CONFIG_BOOTARGS "root=/dev/nfs " \
+ "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \
+ "nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
+#else
+#define CONFIG_BOOTARGS "root=/dev/hda1 " \
+ "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0"
+
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 1 /* PHY address */
+
+#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_PCI | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_KGDB | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DATE | \
+ CFG_CMD_BEDBUG | \
+ CFG_CMD_ELF )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+/*
+ * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
+ * The Linux BASE_BAUD define should match this configuration.
+ * baseBaud = cpuClock/(uartDivisor*16)
+ * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * set Linux BASE_BAUD to 403200.
+ */
+#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
+#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
+#define CFG_BASE_BAUD 691200
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0x00000000 /* disabled */
+#define CFG_PCI_PTM2MS 0x00000000 /* disabled */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+
+/*-----------------------------------------------------------------------
+ * External peripheral base address
+ *-----------------------------------------------------------------------
+ */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
+
+#define CFG_KEY_REG_BASE_ADDR 0xF0100000
+#define CFG_IR_REG_BASE_ADDR 0xF0200000
+#define CFG_FPGA_REG_BASE_ADDR 0xF0300000
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xFFF80000
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+/* BEG ENVIRONNEMENT FLASH */
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_OFFSET 0x00050000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
+#endif
+/* END ENVIRONNEMENT FLASH */
+/*-----------------------------------------------------------------------
+ * NVRAM organization
+ */
+#define CFG_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
+#define CFG_NVRAM_SIZE 0x1ff8 /* NVRAM size */
+
+#ifdef CFG_ENV_IS_IN_NVRAM
+#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */
+#define CFG_ENV_ADDR \
+ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
+#endif
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
+
+
+/* Configuration Port location */
+#define CONFIG_PORT_ADDR 0xF0000500
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_DCACHE_CS 4 /* use cs # 4 for data cache memory */
+
+#define CFG_INIT_RAM_ADDR 0x40000000 /* inside of SDRAM */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for Serial Presence Detect EEPROM address
+ * (to get SDRAM settings)
+ */
+#define SPD_EEPROM_ADDRESS 0x50
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC855 1 /* This is a MPC855 CPU */
+#define CONFIG_C2MON 1 /* ...on a C2MON module */
+
+#define CONFIG_80MHz 1 /* Running at 5 * 16 = 80 MHz */
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#undef CONFIG_STATUS_LED /* Status LED disabled */
+
+#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_FEC_ENET 1 /* Use Fast Ethernet Controller */
+
+#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_IDE | \
+ CFG_CMD_DATE )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#undef CFG_HUSH_PARSER /* use "hush" command parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFFF00000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0x40000000
+#if defined(DEBUG)
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#endif
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#ifndef CONFIG_CAN_DRIVER
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#else /* we must activate GPL5 in the SIUMCR for CAN */
+#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#endif /* CONFIG_CAN_DRIVER */
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit
+ *
+ * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
+ */
+#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
+#define CFG_PLPRCR \
+ ( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
+#else /* up to 50 MHz we use a 1:1 clock */
+#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+#endif /* CONFIG_80MHz */
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
+#define CFG_SCCR (/* SCCR_TBS | */ \
+ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+#else /* up to 50 MHz we use a 1:1 clock */
+#define CFG_SCCR (SCCR_TBS | \
+ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+#endif /* CONFIG_80MHz */
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ * PCMCIA Power Switch
+ *
+ * The C2MON uses a TPS2211A PC-Card Power-Interface Switch to
+ * control the voltages on the PCMCIA slot which is connected
+ * to Port C (all outputs) and Port B (Over-Current Input)
+ *-----------------------------------------------------------------------
+ */
+ /* Output pins */
+#define TPS2211_VCCD0 0x0002 /* PC.14 */
+#define TPS2211_VCCD1 0x0004 /* PC.13 */
+#define TPS2211_VPPD0 0x0008 /* PC.12 */
+#define TPS2211_VPPD1 0x0010 /* PC.11 */
+#define TPS2211_OUTPUTS ( TPS2211_VCCD0 | TPS2211_VCCD1 | \
+ TPS2211_VPPD0 | TPS2211_VPPD1 )
+
+ /* Input pins */
+#define TPS2211_OC 0x00000200 /* PB.22: Over-Current */
+#define TPS2211_INPUTS ( TPS2211_OC )
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
+ *-----------------------------------------------------------------------
+ */
+
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET 0x0100
+
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define CFG_DER 0x2002000F*/
+#define CFG_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
+
+/* used to re-map FLASH both when starting from SRAM or FLASH:
+ * restrict access enough to keep SRAM working (if any)
+ * but not too much to meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
+
+/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \
+ OR_SCY_5_CLK | OR_EHTR)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+
+#define CFG_OR1_REMAP CFG_OR0_REMAP
+#define CFG_OR1_PRELIM CFG_OR0_PRELIM
+#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
+
+/*
+ * BR2/3 and OR2/3 (SDRAM)
+ *
+ */
+#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
+#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
+#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
+
+/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
+#define CFG_OR_TIMING_SDRAM 0x00000A00
+
+#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
+#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+
+#ifndef CONFIG_CAN_DRIVER
+#define CFG_OR3_PRELIM CFG_OR2_PRELIM
+#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
+#define CFG_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
+#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
+#define CFG_OR3_CAN (CFG_CAN_OR_AM | OR_G5LA | OR_BI)
+#define CFG_BR3_CAN ((CFG_CAN_BASE & BR_BA_MSK) | \
+ BR_PS_8 | BR_MS_UPMB | BR_V )
+#endif /* CONFIG_CAN_DRIVER */
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2000
+ * Murray Jensen <Murray.Jensen@cmst.csiro.au>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Config header file for Cogent platform using an MPC8xx CPU module
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
+#define CONFIG_COGENT 1 /* using Cogent Modular Architecture */
+
+/* Cogent Modular Architecture options */
+#define CONFIG_CMA282 1 /* ...on a CMA282 CPU module */
+#define CONFIG_CMA111 1 /* ...on a CMA111 motherboard */
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#define CONFIG_CONS_ON_SMC /* define if console on SMC */
+#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else*/
+#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
+#undef CONFIG_CONS_USE_EXTC /* SMC/SCC use ext clock not brg_clk */
+#define CONFIG_CONS_EXTC_RATE 3686400 /* SMC/SCC ext clk rate in Hz */
+#define CONFIG_CONS_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9,1=CLK5/CLK15*/
+
+/*
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ */
+#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
+#undef CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+#define CONFIG_ETHER_NONE /* define if ether on something else */
+#define CONFIG_ETHER_INDEX 1 /* which channel for ether */
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#define CONFIG_8260_CLKIN 66666666 /* in Hz */
+
+#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
+#define CONFIG_BAUDRATE 230400
+#else
+#define CONFIG_BAUDRATE 9600
+#endif
+
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL|CFG_CMD_KGDB)&~CFG_CMD_NET)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#ifdef DEBUG
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+#define CONFIG_BOOTCOMMAND "bootm 04080000 04200000" /* autoboot command*/
+
+#define CONFIG_BOOTARGS "root=/dev/ram rw"
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
+#undef CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
+#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
+#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */
+#define CONFIG_KGDB_USE_EXTC /* SMC/SCC use ext clock not brg_clk */
+#define CONFIG_KGDB_EXTC_RATE 3686400 /* serial ext clk rate in Hz */
+#define CONFIG_KGDB_EXTC_PINSEL 0 /* pin select 0=CLK3/CLK9,1=CLK5/CLK15*/
+# if defined(CONFIG_KGDB_NONE) || defined(CONFIG_KGDB_USE_EXTC)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port at */
+# else
+#define CONFIG_KGDB_BAUDRATE 9600 /* speed to run kgdb serial port at */
+# endif
+#endif
+
+#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x01c00000 /* 4 ... 28 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Low Level Cogent settings
+ * if CFG_CMA_CONS_SERIAL is defined, make sure the 8260 CPM serial is not.
+ * also, make sure CONFIG_CONS_INDEX is still defined - the index will be
+ * 1 for serialA, 2 for serialB, 3 for ser2A, 4 for ser2B
+ * (second 2 for CMA120 only)
+ */
+#define CFG_CMA_MB_BASE 0x00000000 /* base of m/b address space */
+
+#include <configs/cogent_common.h>
+
+#ifdef CONFIG_CONS_NONE
+#define CFG_CMA_CONS_SERIAL /* use Cogent motherboard serial for console */
+#endif
+#define CFG_CMA_LCD_HEARTBEAT /* define for sec rotator in lcd corner */
+
+#if (CMA_MB_CAPS & CMA_MB_CAP_FLASH)
+/*
+ * flash exists on the motherboard
+ * set these four according to TOP dipsw:
+ * TOP on => ..._FLLOW_... (boot EPROM space is high so FLASH is low )
+ * TOP off => ..._FLHIGH_... (boot EPROM space is low so FLASH is high)
+ */
+#define CMA_MB_FLASH_EXEC_BASE CMA_MB_FLLOW_EXEC_BASE
+#define CMA_MB_FLASH_EXEC_SIZE CMA_MB_FLLOW_EXEC_SIZE
+#define CMA_MB_FLASH_RDWR_BASE CMA_MB_FLLOW_RDWR_BASE
+#define CMA_MB_FLASH_RDWR_SIZE CMA_MB_FLLOW_RDWR_SIZE
+#endif
+#define CMA_MB_FLASH_BASE CMA_MB_FLASH_EXEC_BASE
+#define CMA_MB_FLASH_SIZE CMA_MB_FLASH_EXEC_SIZE
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * if you change bits in the HRCW, you must also change the CFG_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ */
+#define CFG_HRCW_MASTER (HRCW_EBM|HRCW_BPS10|HRCW_L2CPC10|HRCW_DPPC11|\
+ HRCW_ISB100|HRCW_MMR11|HRCW_MODCK_H0101)
+/* no slaves so just duplicate the master hrcw */
+#define CFG_HRCW_SLAVE1 CFG_HRCW_MASTER
+#define CFG_HRCW_SLAVE2 CFG_HRCW_MASTER
+#define CFG_HRCW_SLAVE3 CFG_HRCW_MASTER
+#define CFG_HRCW_SLAVE4 CFG_HRCW_MASTER
+#define CFG_HRCW_SLAVE5 CFG_HRCW_MASTER
+#define CFG_HRCW_SLAVE6 CFG_HRCW_MASTER
+#define CFG_HRCW_SLAVE7 CFG_HRCW_MASTER
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE CMA_MB_RAM_BASE
+#ifdef CONFIG_CMA302
+#define CFG_FLASH_BASE CMA_MB_SLOT2_BASE /* cma302 in slot 2 */
+#else
+#define CFG_FLASH_BASE CMA_MB_FLASH_BASE /* flash on m/b */
+#endif
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max num of memory banks */
+#define CFG_MAX_FLASH_SECT 67 /* max num of sects on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR CFG_FLASH_BASE /* Addr of Environment Sector */
+#ifdef CONFIG_CMA302
+#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE (512*1024) /* see README - env sect real size */
+#else
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers 2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CFG_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
+ HID0_IFEM|HID0_ABE)
+#define CFG_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE)
+#define CFG_HID2 0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CFG_RMR RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration 4-25
+ *-----------------------------------------------------------------------
+ */
+#define CFG_BCR BCR_EBM
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 4-31
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SIUMCR (SIUMCR_DPPC11|SIUMCR_L2CPC10|SIUMCR_MMR11)
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+ SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control 4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control 9-8
+ *-----------------------------------------------------------------------
+ * Ensure DFBRG is Divide by 16
+ */
+#define CFG_SCCR (SCCR_DFBRG01)
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration 13-7
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR 0
+
+#if defined(CONFIG_CMA282)
+
+/*
+ * Init Memory Controller:
+ *
+ * According to the Cogent manual, only CS0 and CS2 are used - CS0 for EPROM
+ * and CS2 for (optional) local bus RAM on the CPU module.
+ *
+ * Note the motherboard address space (256 Mbyte in size) is connected
+ * to the 60x Bus and is located starting at address 0. The Hard Reset
+ * Configuration Word should put the 60x Bus into External Bus Mode, since
+ * we dont set up any memory controller maps for it (see BCR[EBM], 4-26).
+ *
+ * (the *_SIZE vars must be a power of 2)
+ */
+
+#define CFG_CMA_CS0_BASE TEXT_BASE /* EPROM */
+#define CFG_CMA_CS0_SIZE (1 << 20)
+#if 0
+#define CFG_CMA_CS2_BASE 0x10000000 /* Local Bus SDRAM */
+#define CFG_CMA_CS2_SIZE (16 << 20)
+#endif
+
+/*
+ * CS0 maps the EPROM on the cpu module
+ * Set it for 10 wait states, address CFG_MONITOR_BASE and size 1M
+ *
+ * Note: We must have already transferred control to the final location
+ * of the EPROM before these are used, because when BR0/OR0 are set, the
+ * mirror of the eprom at any other addresses will disappear.
+ */
+
+/* base address = CFG_CMA_CS0_BASE, 16-bit, no parity, r/o, gpcm (60x bus) */
+#define CFG_BR0_PRELIM ((CFG_CMA_CS0_BASE&BRx_BA_MSK)|BRx_PS_16|BRx_WP|BRx_V)
+/* mask size CFG_CMA_CS0_SIZE, csneg 1/4 early, adr-to-cs 1/2, 10-wait states */
+#define CFG_OR0_PRELIM (P2SZ_TO_AM(CFG_CMA_CS0_SIZE)|\
+ ORxG_CSNT|ORxG_ACS_DIV2|ORxG_SCY_10_CLK)
+
+/*
+ * CS2 enables the Local Bus SDRAM on the CPU Module
+ *
+ * Will leave this unset for the moment, because a) my CPU module has no
+ * SDRAM installed (it is optional); and b) it will require programming
+ * one of the UPMs in SDRAM mode - not a trivial job, and hard to get right
+ * if you can't test it.
+ */
+
+#if 0
+/* base address = CFG_CMA_CS2_BASE, 32-bit, no parity, ??? */
+#define CFG_BR0_PRELIM ((CFG_CMA_CS2_BASE&BRx_BA_MSK)|BRx_PS_32|/*???*/|BRx_V)
+/* mask size CFG_CMA_CS2_SIZE, CS time normal, ??? */
+#define CFG_OR2_PRELIM ((~(CFG_CMA_CS2_SIZE-1)&ORx_AM_MSK)|/*???*/)
+#endif
+
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH*/
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2000
+ * Murray Jensen <Murray.Jensen@cmst.csiro.au>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Config header file for Cogent platform using an MPC8xx CPU module
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC860 1 /* This is an MPC860 CPU */
+#define CONFIG_COGENT 1 /* using Cogent Modular Architecture */
+
+/* Cogent Modular Architecture options */
+#define CONFIG_CMA286_60_OLD 1 /* ...on an old CMA286-60 CPU module */
+#define CONFIG_CMA102 1 /* ...on a CMA102 motherboard */
+#define CONFIG_CMA302 1 /* ...with a CMA302 flash I/O module */
+
+/* serial console configuration */
+#undef CONFIG_8xx_CONS_SMC1
+#undef CONFIG_8xx_CONS_SMC2
+#define CONFIG_8xx_CONS_NONE /* not on 8xx serial ports (eg on cogent m/b) */
+
+#if defined(CONFIG_CMA286_60_OLD)
+#define CONFIG_8xx_GCLK_FREQ 33333000 /* define if cant use get_gclk_freq */
+#endif
+
+#define CONFIG_BAUDRATE 230400
+
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_KGDB | CFG_CMD_I2C) & ~CFG_CMD_NET)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+#define CONFIG_BOOTCOMMAND "bootm 04080000 04200000" /* autoboot command*/
+
+#define CONFIG_BOOTARGS "root=/dev/ram rw"
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
+#undef CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
+#define CONFIG_KGDB_NONE /* define if kgdb on something else */
+#define CONFIG_KGDB_INDEX 2 /* which SMC/SCC channel for kgdb */
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+#define CONFIG_WATCHDOG /* turn on platform specific watchdog */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x01c00000 /* 4 ... 28 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+
+#define CFG_ALLOC_DPRAM
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Low Level Cogent settings
+ * if CFG_CMA_CONS_SERIAL is defined, make sure the 8xx CPM serial is not.
+ * also, make sure CONFIG_CONS_INDEX is still defined - the index will be
+ * 1 for serialA, 2 for serialB, 3 for ser2A, 4 for ser2B
+ * (second 2 for CMA120 only)
+ */
+#define CFG_CMA_MB_BASE 0x00000000 /* base of m/b address space */
+
+#include <configs/cogent_common.h>
+
+#define CFG_CMA_CONS_SERIAL /* use Cogent motherboard serial for console */
+#define CONFIG_CONS_INDEX 1
+#define CFG_CMA_LCD_HEARTBEAT /* define for sec rotator in lcd corner */
+#if (CMA_MB_CAPS & CMA_MB_CAP_FLASH)
+/*
+ * flash exists on the motherboard
+ * set these four according to TOP dipsw:
+ * TOP on => ..._FLLOW_... (boot EPROM space is high so FLASH is low )
+ * TOP off => ..._FLHIGH_... (boot EPROM space is low so FLASH is high)
+ */
+#define CMA_MB_FLASH_EXEC_BASE CMA_MB_FLLOW_EXEC_BASE
+#define CMA_MB_FLASH_EXEC_SIZE CMA_MB_FLLOW_EXEC_SIZE
+#define CMA_MB_FLASH_RDWR_BASE CMA_MB_FLLOW_RDWR_BASE
+#define CMA_MB_FLASH_RDWR_SIZE CMA_MB_FLLOW_RDWR_SIZE
+#endif
+#define CMA_MB_FLASH_BASE CMA_MB_FLASH_EXEC_BASE
+#define CMA_MB_FLASH_SIZE CMA_MB_FLASH_EXEC_SIZE
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFF000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE CMA_MB_RAM_BASE
+#ifdef CONFIG_CMA302
+#define CFG_FLASH_BASE CMA_MB_SLOT2_BASE /* cma302 in slot 2 */
+#else
+#define CFG_FLASH_BASE CMA_MB_FLASH_BASE /* flash on m/b */
+#endif
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR CFG_FLASH_BASE /* Addr of Environment Sector */
+#ifdef CONFIG_CMA302
+#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE (512*1024) /* see README - env sect real size */
+#else
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#endif
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit - leave PLL multiplication factor unchanged !
+ */
+#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+#define CFG_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \
+ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
+ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
+ SCCR_DFALCD00)
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+/*#define CFG_DER 0x2002000F*/
+#define CFG_DER 0
+
+#if defined(CONFIG_CMA286_60_OLD)
+
+/*
+ * Init Memory Controller:
+ *
+ * NOTE: although the names (CFG_xRn_PRELIM) suggest preliminary settings,
+ * they are actually the final settings for this cpu/board, because the
+ * flash and RAM are on the motherboard, accessed via the CMAbus, and the
+ * mappings are pretty much fixed.
+ *
+ * (the *_SIZE vars must be a power of 2)
+ */
+
+#define CFG_CMA_CS0_BASE TEXT_BASE /* EPROM */
+#define CFG_CMA_CS0_SIZE (1 << 20)
+#define CFG_CMA_CS1_BASE CMA_MB_RAM_BASE /* RAM + I/O SLOT 1 */
+#define CFG_CMA_CS1_SIZE (64 << 20)
+#define CFG_CMA_CS2_BASE CMA_MB_SLOT2_BASE /* I/O SLOTS 2 + 3 */
+#define CFG_CMA_CS2_SIZE (64 << 20)
+#define CFG_CMA_CS3_BASE CMA_MB_ROMLOW_BASE /* M/B I/O */
+#define CFG_CMA_CS3_SIZE (32 << 20)
+
+/*
+ * CS0 maps the EPROM on the cpu module
+ * Set it for 4 wait states, address CFG_MONITOR_BASE and size 1M
+ *
+ * Note: We must have already transferred control to the final location
+ * of the EPROM before these are used, because when BR0/OR0 are set, the
+ * mirror of the eprom at any other addresses will disappear.
+ */
+
+/* base address = CFG_CMA_CS0_BASE, 16-bit, no parity, r/o, gpcm */
+#define CFG_BR0_PRELIM ((CFG_CMA_CS0_BASE&BR_BA_MSK)|BR_PS_16|BR_WP|BR_V)
+/* mask size CFG_CMA_CS0_SIZE, CS time normal, burst inhibit, 4-wait states */
+#define CFG_OR0_PRELIM ((~(CFG_CMA_CS0_SIZE-1)&OR_AM_MSK)|OR_BI|OR_SCY_4_CLK)
+
+/*
+ * CS1 maps motherboard DRAM and motherboard I/O slot 1
+ * (each 32Mbyte in size)
+ */
+
+/* base address = CFG_CMA_CS1_BASE, 32-bit, no parity, r/w, gpcm */
+#define CFG_BR1_PRELIM ((CFG_CMA_CS1_BASE&BR_BA_MSK)|BR_V)
+/* mask size CFG_CMA_CS1_SIZE, CS time normal, burst ok, ext xfer ack */
+#define CFG_OR1_PRELIM ((~(CFG_CMA_CS1_SIZE-1)&OR_AM_MSK)|OR_SETA)
+
+/*
+ * CS2 maps motherboard I/O slots 2 and 3
+ * (each 32Mbyte in size)
+ */
+
+/* base address = CFG_CMA_CS2_BASE, 32-bit, no parity, r/w, gpcm */
+#define CFG_BR2_PRELIM ((CFG_CMA_CS2_BASE&BR_BA_MSK)|BR_V)
+/* mask size CFG_CMA_CS2_SIZE, CS time normal, burst ok, ext xfer ack */
+#define CFG_OR2_PRELIM ((~(CFG_CMA_CS2_SIZE-1)&OR_AM_MSK)|OR_SETA)
+
+/*
+ * CS3 maps motherboard I/O
+ * (32Mbyte in size)
+ */
+
+/* base address = CFG_CMA_CS3_BASE, 32-bit, no parity, r/w, gpcm */
+#define CFG_BR3_PRELIM ((CFG_CMA_CS3_BASE&BR_BA_MSK)|BR_V)
+/* mask size CFG_CMA_CS3_SIZE, CS time normal, burst inhibit, ext xfer ack */
+#define CFG_OR3_PRELIM ((~(CFG_CMA_CS3_SIZE-1)&OR_AM_MSK)|OR_BI|OR_SETA)
+
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * Workaround for layout bug on prototype board
+ */
+#define PCU_E_WITH_SWAPPED_CS 1
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC860 1 /* This is a MPC860T CPU */
+#define CONFIG_MPC860T 1
+#define CONFIG_PCU_E 1 /* ...on a PCU E board */
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+
+#define CONFIG_BAUDRATE 9600
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "bootp;" \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
+ "bootm"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+
+#define CONFIG_PRAM 2048 /* reserve 2 MB "protected RAM" */
+
+#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+
+#define CONFIG_SPI /* enable SPI driver */
+#define CONFIG_SPI_X /* 16 bit EEPROM addressing */
+
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+
+/* ----------------------------------------------------------------
+ * Offset to initial SPI buffers in DPRAM (used if the environment
+ * is in the SPI EEPROM): We need a 520 byte scratch DPRAM area to
+ * use at an early stage. It is used between the two initialization
+ * calls (spi_init_f() and spi_init_r()). The value 0xB00 makes it
+ * far enough from the start of the data area (as well as from the
+ * stack pointer).
+ * ---------------------------------------------------------------- */
+#define CFG_SPI_INIT_OFFSET 0xB00
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_DATE | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_BSP )
+
+#define CONFIG_BOOTP_MASK \
+ ((CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) & ~CONFIG_BOOTP_GATEWAY)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x00100000 /* default load address */
+
+#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
+
+/* Ethernet hardware configuration done using port pins */
+#define CFG_PB_ETH_RESET 0x00000020 /* PB 26 */
+#if PCU_E_WITH_SWAPPED_CS /* XXX */
+#define CFG_PA_ETH_MDDIS 0x4000 /* PA 1 */
+#define CFG_PB_ETH_POWERDOWN 0x00000800 /* PB 20 */
+#define CFG_PB_ETH_CFG1 0x00000400 /* PB 21 */
+#define CFG_PB_ETH_CFG2 0x00000200 /* PB 22 */
+#define CFG_PB_ETH_CFG3 0x00000100 /* PB 23 */
+#else /* XXX */
+#define CFG_PB_ETH_MDDIS 0x00000010 /* PB 27 */
+#define CFG_PB_ETH_POWERDOWN 0x00000100 /* PB 23 */
+#define CFG_PB_ETH_CFG1 0x00000200 /* PB 22 */
+#define CFG_PB_ETH_CFG2 0x00000400 /* PB 21 */
+#define CFG_PB_ETH_CFG3 0x00000800 /* PB 20 */
+#endif /* XXX */
+
+/* Ethernet settings:
+ * MDIO enabled, autonegotiation, 10/100Mbps, half/full duplex
+ */
+#define CFG_ETH_MDDIS_VALUE 0
+#define CFG_ETH_CFG1_VALUE 1
+#define CFG_ETH_CFG2_VALUE 1
+#define CFG_ETH_CFG3_VALUE 1
+
+/* PUMA configuration */
+#if PCU_E_WITH_SWAPPED_CS /* XXX */
+#define CFG_PB_PUMA_PROG 0x00000010 /* PB 27 */
+#else /* XXX */
+#define CFG_PA_PUMA_PROG 0x4000 /* PA 1 */
+#endif /* XXX */
+#define CFG_PC_PUMA_DONE 0x0008 /* PC 12 */
+#define CFG_PC_PUMA_INIT 0x0004 /* PC 13 */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xFE000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Address accessed to reset the board - must not be mapped/assigned
+ */
+#define CFG_RESET_ADDRESS 0xFEFFFFFF
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+/* this is an ugly hack needed because of the silly non-constant address map */
+#define CFG_FLASH_BASE (0-flash_info[0].size-flash_info[1].size)
+
+#if defined(DEBUG)
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#else
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#endif
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 160 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
+
+#if 0
+/* Start port with environment in flash; switch to SPI EEPROM later */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment */
+#define CFG_ENV_ADDR 0xFFFFE000 /* Address of Environment Sector */
+#define CFG_ENV_SECT_SIZE 0x2000 /* use the top-most 8k boot sector */
+#else
+/* Final version: environment in EEPROM */
+#define CFG_ENV_IS_IN_EEPROM 1
+#define CFG_I2C_EEPROM_ADDR 0
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_ENV_OFFSET 1024
+#define CFG_ENV_SIZE 1024
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * External Arbitration max. priority (7),
+ * Debug pins configuration '11',
+ * Asynchronous external master enable.
+ */
+/* => 0x70600200 */
+#define CFG_SIUMCR (SIUMCR_EARP7 | SIUMCR_DBGC11 | SIUMCR_AEME)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit, set PLL multiplication factor !
+ */
+/* 0x00004080 */
+#define CFG_PLPRCR_MF 0 /* (0+1) * 50 = 50 MHz Clock */
+#define CFG_PLPRCR \
+ ( (CFG_PLPRCR_MF << PLPRCR_MF_SHIFT) | \
+ PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \
+ /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \
+ PLPRCR_CSR /*| PLPRCR_LOLRE|PLPRCR_FIOPD*/ \
+ )
+
+#define CONFIG_8xx_GCLK_FREQ ((CFG_PLPRCR_MF+1)*50000000)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ *
+ * Note: PITRTCLK is 50MHz / 512 = 97'656.25 Hz
+ */
+#define SCCR_MASK SCCR_EBDF11
+/* 0x01800000 */
+#define CFG_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \
+ SCCR_RTDIV | SCCR_RTSEL | \
+ /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \
+ SCCR_EBDF00 | SCCR_DFSYNC00 | \
+ SCCR_DFBRG00 | SCCR_DFNL000 | \
+ SCCR_DFNH000 | SCCR_DFLCD100 | \
+ SCCR_DFALCD01)
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register 11-27
+ *-----------------------------------------------------------------------
+ *
+ * Note: RTC counts at PITRTCLK / 8'192 = 11.920928 Hz !!!
+ *
+ * Don't expect the "date" command to work without a 32kHz clock input!
+ */
+/* 0x00C3 => 0x0003 */
+#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
+
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration Register 19-4
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR 0x0000
+
+/*-----------------------------------------------------------------------
+ * RMDS - RISC Microcode Development Support Control Register
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RMDS 0
+
+/*-----------------------------------------------------------------------
+ *
+ * Interrupt Levels
+ *-----------------------------------------------------------------------
+ */
+#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */
+
+/*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH) - second Flash bank optional
+ */
+
+#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */
+#if PCU_E_WITH_SWAPPED_CS /* XXX */
+#define FLASH_BASE6_PRELIM 0xFF000000 /* FLASH bank #1 */
+#else /* XXX */
+#define FLASH_BASE1_PRELIM 0xFF000000 /* FLASH bank #1 */
+#endif /* XXX */
+
+/*
+ * used to re-map FLASH: restrict access enough but not too much to
+ * meddle with FLASH accesses
+ */
+#define CFG_REMAP_OR_AM 0xFF800000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
+
+/* FLASH timing: CSNT = 0, ACS = 00, SCY = 8, EHTR = 1 */
+#define CFG_OR_TIMING_FLASH (OR_SCY_8_CLK | OR_EHTR)
+
+#define CFG_OR0_REMAP ( CFG_REMAP_OR_AM | OR_ACS_DIV1 | OR_BI | \
+ CFG_OR_TIMING_FLASH)
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | OR_ACS_DIV1 | OR_BI | \
+ CFG_OR_TIMING_FLASH)
+/* 16 bit, bank valid */
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
+
+#if PCU_E_WITH_SWAPPED_CS /* XXX */
+#define CFG_OR6_REMAP CFG_OR0_REMAP
+#define CFG_OR6_PRELIM CFG_OR0_PRELIM
+#define CFG_BR6_PRELIM ((FLASH_BASE6_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
+#else /* XXX */
+#define CFG_OR1_REMAP CFG_OR0_REMAP
+#define CFG_OR1_PRELIM CFG_OR0_PRELIM
+#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
+#endif /* XXX */
+
+/*
+ * BR2/OR2: SDRAM
+ *
+ * Multiplexed addresses, GPL5 output to GPL5_A (don't care)
+ */
+#if PCU_E_WITH_SWAPPED_CS /* XXX */
+#define SDRAM_BASE5_PRELIM 0x00000000 /* SDRAM bank */
+#else /* XXX */
+#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank */
+#endif /* XXX */
+#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map 128 MB (>SDRAM_MAX_SIZE!) */
+#define SDRAM_TIMING OR_CSNT_SAM /* SDRAM-Timing */
+
+#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */
+
+#if PCU_E_WITH_SWAPPED_CS /* XXX */
+#define CFG_OR5_PRELIM (SDRAM_PRELIM_OR_AM | SDRAM_TIMING )
+#define CFG_BR5_PRELIM ((SDRAM_BASE5_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#else /* XXX */
+#define CFG_OR2_PRELIM (SDRAM_PRELIM_OR_AM | SDRAM_TIMING )
+#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#endif /* XXX */
+
+/*
+ * BR3/OR3: CAN Controller
+ * BR3: 0x10000401 OR3: 0xffff818a
+ */
+#define CAN_CTRLR_BASE 0x10000000 /* CAN Controller */
+#define CAN_CTRLR_OR_AM 0xFFFF8000 /* 32 kB */
+#define CAN_CTRLR_TIMING (OR_BI | OR_SCY_8_CLK | OR_SETA | OR_EHTR)
+
+#if PCU_E_WITH_SWAPPED_CS /* XXX */
+#define CFG_BR4_PRELIM ((CAN_CTRLR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
+#define CFG_OR4_PRELIM (CAN_CTRLR_OR_AM | CAN_CTRLR_TIMING)
+#else /* XXX */
+#define CFG_BR3_PRELIM ((CAN_CTRLR_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
+#define CFG_OR3_PRELIM (CAN_CTRLR_OR_AM | CAN_CTRLR_TIMING)
+#endif /* XXX */
+
+/*
+ * BR4/OR4: PUMA Config
+ *
+ * Memory controller will be used in 2 modes:
+ *
+ * - "read" mode:
+ * BR4: 0x10100801 OR4: 0xffff8530
+ * - "load" mode (chip select on UPM B):
+ * BR4: 0x101008c1 OR4: 0xffff8630
+ *
+ * Default initialization is in "read" mode
+ */
+#define PUMA_CONF_BASE 0x10100000 /* PUMA Config */
+#define PUMA_CONF_OR_AM 0xFFFF8000 /* 32 kB */
+#define PUMA_CONF_LOAD_TIMING (OR_ACS_DIV2 | OR_SCY_3_CLK)
+#define PUMA_CONF_READ_TIMING (OR_G5LA | OR_BI | OR_SCY_3_CLK)
+
+#define PUMA_CONF_BR_LOAD ((PUMA_CONF_BASE & BR_BA_MSK) | \
+ BR_PS_16 | BR_MS_UPMB | BR_V)
+#define PUMA_CONF_OR_LOAD (PUMA_CONF_OR_AM | PUMA_CONF_LOAD_TIMING)
+
+#define PUMA_CONF_BR_READ ((PUMA_CONF_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
+#define PUMA_CONF_OR_READ (PUMA_CONF_OR_AM | PUMA_CONF_READ_TIMING)
+
+#if PCU_E_WITH_SWAPPED_CS /* XXX */
+#define CFG_BR3_PRELIM PUMA_CONF_BR_READ
+#define CFG_OR3_PRELIM PUMA_CONF_OR_READ
+#else /* XXX */
+#define CFG_BR4_PRELIM PUMA_CONF_BR_READ
+#define CFG_OR4_PRELIM PUMA_CONF_OR_READ
+#endif /* XXX */
+
+/*
+ * BR5/OR5: PUMA: SMA Bus 8 Bit
+ * BR5: 0x10200401 OR5: 0xffe0010a
+ */
+#define PUMA_SMA8_BASE 0x10200000 /* PUMA SMA Bus 8 Bit */
+#define PUMA_SMA8_OR_AM 0xFFE00000 /* 2 MB */
+#define PUMA_SMA8_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR)
+
+#if PCU_E_WITH_SWAPPED_CS /* XXX */
+#define CFG_BR2_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
+#define CFG_OR2_PRELIM (PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA)
+#else /* XXX */
+#define CFG_BR5_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
+#define CFG_OR5_PRELIM (PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA)
+#endif /* XXX */
+
+/*
+ * BR6/OR6: PUMA: SMA Bus 16 Bit
+ * BR6: 0x10600801 OR6: 0xffe0010a
+ */
+#define PUMA_SMA16_BASE 0x10600000 /* PUMA SMA Bus 16 Bit */
+#define PUMA_SMA16_OR_AM 0xFFE00000 /* 2 MB */
+#define PUMA_SMA16_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR)
+
+#if PCU_E_WITH_SWAPPED_CS /* XXX */
+#define CFG_BR1_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
+#define CFG_OR1_PRELIM (PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA)
+#else /* XXX */
+#define CFG_BR6_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
+#define CFG_OR6_PRELIM (PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA)
+#endif /* XXX */
+
+/*
+ * BR7/OR7: PUMA: external Flash
+ * BR7: 0x10a00801 OR7: 0xfe00010a
+ */
+#define PUMA_FLASH_BASE 0x10A00000 /* PUMA external Flash */
+#define PUMA_FLASH_OR_AM 0xFE000000 /* 32 MB */
+#define PUMA_FLASH_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR)
+
+#define CFG_BR7_PRELIM ((PUMA_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
+#define CFG_OR7_PRELIM (PUMA_FLASH_OR_AM | PUMA_FLASH_TIMING | OR_SETA)
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MPTPR 0x0200
+
+/*
+ * MAMR settings for SDRAM
+ * 0x30104118 = Timer A period 0x30, MAMR_AMB_TYPE_1, MAMR_G0CLB_A10,
+ * MAMR_RLFB_1X, MAMR_WLFB_1X, MAMR_TLFB_8X
+ * 0x30904114 = - " - | Periodic Timer A Enable, MAMR_TLFB_4X
+ */
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA 0x30 /* = 48 */
+
+#define CFG_MAMR ( (CFG_MAMR_PTA << MAMR_PTA_SHIFT) | \
+ MAMR_AMB_TYPE_1 | \
+ MAMR_G0CLB_A10 | \
+ MAMR_RLFB_1X | \
+ MAMR_WLFB_1X | \
+ MAMR_TLFB_8X )
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#endif /* __CONFIG_H */
projects / u-boot.git / commitdiff