ARM: rockchip: Remove the pinctrl request at rk3288-board-spl

If we use the new pinctrl driver, the pinctrl setup will be done
by device probe. Remove the pinctrl setup at rk3288-board-spl.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

diff --git a/arch/arm/mach-rockchip/rk3288-board-spl.c b/arch/arm/mach-rockchip/rk3288-board-spl.c
index 236cb932baf6f8bbae3215cda6e2ba4d257543a9..93c772184d330a59f14c5c2b17d8d6a3434d0335 100644 (file)
--- a/arch/arm/mach-rockchip/rk3288-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3288-board-spl.c
@@ -78,45 +78,6 @@ fallback:
        return BOOT_DEVICE_MMC1;
 }
 
-#ifdef CONFIG_SPL_MMC_SUPPORT
-static int configure_emmc(struct udevice *pinctrl)
-{
-#if defined(CONFIG_TARGET_CHROMEBOOK_JERRY)
-
-       struct gpio_desc desc;
-       int ret;
-
-       pinctrl_request_noflags(pinctrl, PERIPH_ID_EMMC);
-
-       /*
-        * TODO(sjg@chromium.org): Pick this up from device tree or perhaps
-        * use the EMMC_PWREN setting.
-        */
-       ret = dm_gpio_lookup_name("D9", &desc);
-       if (ret) {
-               debug("gpio ret=%d\n", ret);
-               return ret;
-       }
-       ret = dm_gpio_request(&desc, "emmc_pwren");
-       if (ret) {
-               debug("gpio_request ret=%d\n", ret);
-               return ret;
-       }
-       ret = dm_gpio_set_dir_flags(&desc, GPIOD_IS_OUT);
-       if (ret) {
-               debug("gpio dir ret=%d\n", ret);
-               return ret;
-       }
-       ret = dm_gpio_set_value(&desc, 1);
-       if (ret) {
-               debug("gpio value ret=%d\n", ret);
-               return ret;
-       }
-#endif
-       return 0;
-}
-#endif
-
 #if !defined(CONFIG_SPL_OF_PLATDATA)
 static int phycore_init(void)
 {
@@ -145,7 +106,6 @@ static int phycore_init(void)
 
 void board_init_f(ulong dummy)
 {
-       struct udevice *pinctrl;
        struct udevice *dev;
        int ret;
 
@@ -184,12 +144,6 @@ void board_init_f(ulong dummy)
                return;
        }
 
-       ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
-       if (ret) {
-               debug("Pinctrl init failed: %d\n", ret);
-               return;
-       }
-
 #if !defined(CONFIG_SPL_OF_PLATDATA)
        if (of_machine_is_compatible("phytec,rk3288-phycore-som")) {
                ret = phycore_init();
@@ -240,52 +194,19 @@ static int setup_led(void)
 
 void spl_board_init(void)
 {
-       struct udevice *pinctrl;
        int ret;
 
        ret = setup_led();
-
        if (ret) {
                debug("LED ret=%d\n", ret);
                hang();
        }
 
-       ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
-       if (ret) {
-               debug("%s: Cannot find pinctrl device\n", __func__);
-               goto err;
-       }
-
-#ifdef CONFIG_SPL_MMC_SUPPORT
-       ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD);
-       if (ret) {
-               debug("%s: Failed to set up SD card\n", __func__);
-               goto err;
-       }
-       ret = configure_emmc(pinctrl);
-       if (ret) {
-               debug("%s: Failed to set up eMMC\n", __func__);
-               goto err;
-       }
-#endif
-
-       /* Enable debug UART */
-       ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
-       if (ret) {
-               debug("%s: Failed to set up console UART\n", __func__);
-               goto err;
-       }
-
        preloader_console_init();
 #if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM)
        back_to_bootrom(BROM_BOOT_NEXTSTAGE);
 #endif
        return;
-err:
-       printf("spl_board_init: Error %d\n", ret);
-
-       /* No way to report error here */
-       hang();
 }
 
 #ifdef CONFIG_SPL_OS_BOOT