--- /dev/null
+/*
+ * Copyright (C) 2014 Soeren Moch <smoch@web.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/sata.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/video.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+DECLARE_GLOBAL_DATA_PTR;
+
+#define WEAK_PULLUP (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_SRE_SLOW)
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+#ifdef CONFIG_SYS_I2C
+/* I2C1, SGTL5000 */
+static struct i2c_pads_info i2c_pad_info0 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
+ .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
+ .gp = IMX_GPIO_NR(5, 27)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
+ .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
+ .gp = IMX_GPIO_NR(5, 26)
+ }
+};
+
+/* I2C2 HDMI */
+static struct i2c_pads_info i2c_pad_info1 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
+ .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
+ .gp = IMX_GPIO_NR(4, 12)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
+ .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
+ .gp = IMX_GPIO_NR(4, 13)
+ }
+};
+
+/* I2C3, CON11, DS1307, PCIe_SMB */
+static struct i2c_pads_info i2c_pad_info2 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
+ .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
+ .gp = IMX_GPIO_NR(1, 3)
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
+ .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
+ .gp = IMX_GPIO_NR(1, 6)
+ }
+};
+#endif /* CONFIG_SYS_I2C */
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart2_pads[] = {
+ MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const enet_pads[] = {
+ MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ /* AR8035 PHY Reset */
+ MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const pcie_pads[] = {
+ /* W_DISABLE# */
+ MX6_PAD_KEY_COL4__GPIO4_IO14 | MUX_PAD_CTRL(WEAK_PULLUP),
+ /* PERST# */
+ MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int dram_init(void)
+{
+ gd->ram_size = 2048ul * 1024 * 1024;
+ return 0;
+}
+
+static void setup_iomux_enet(void)
+{
+ imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+ /* Reset AR8035 PHY */
+ gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
+ udelay(500);
+ gpio_set_value(IMX_GPIO_NR(1, 25), 1);
+}
+
+static void setup_pcie(void)
+{
+ imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
+}
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+ imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+ MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+ MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg[3] = {
+ {USDHC2_BASE_ADDR},
+ {USDHC3_BASE_ADDR},
+ {USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 2)
+#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 0)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
+ case USDHC3_BASE_ADDR:
+ ret = !gpio_get_value(USDHC3_CD_GPIO);
+ break;
+ case USDHC4_BASE_ADDR:
+ ret = 1; /* eMMC/uSDHC4 is always present */
+ break;
+ }
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ s32 status = 0;
+ int i;
+
+ /*
+ * (U-boot device node) (Physical Port)
+ * mmc0 SD2
+ * mmc1 SD3
+ * mmc2 eMMC
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+ gpio_direction_input(USDHC2_CD_GPIO);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ gpio_direction_input(USDHC3_CD_GPIO);
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ break;
+ case 2:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+ usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers"
+ "(%d) then supported by the board (%d)\n",
+ i + 1, CONFIG_SYS_FSL_USDHC_NUM);
+ return status;
+ }
+
+ status |= fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ }
+ return status;
+}
+#endif /* CONFIG_FSL_ESDHC */
+
+#ifdef CONFIG_VIDEO_IPUV3
+static void do_enable_hdmi(struct display_info_t const *dev)
+{
+ imx_enable_hdmi_phy();
+}
+
+struct display_info_t const displays[] = {{
+ .bus = -1,
+ .addr = 0,
+ .pixfmt = IPU_PIX_FMT_RGB24,
+ .detect = detect_hdmi,
+ .enable = do_enable_hdmi,
+ .mode = {
+ .name = "HDMI",
+ /* 1024x768@60Hz (VESA)*/
+ .refresh = 60,
+ .xres = 1024,
+ .yres = 768,
+ .pixclock = 15384,
+ .left_margin = 160,
+ .right_margin = 24,
+ .upper_margin = 29,
+ .lower_margin = 3,
+ .hsync_len = 136,
+ .vsync_len = 6,
+ .sync = FB_SYNC_EXT,
+ .vmode = FB_VMODE_NONINTERLACED
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+
+static void setup_display(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+ s32 timeout = 100000;
+
+ enable_ipu_clock();
+ imx_setup_hdmi();
+
+ /* set video pll to 455MHz (24MHz * (37+11/12) / 2) */
+ reg = readl(&ccm->analog_pll_video);
+ reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN;
+ writel(reg, &ccm->analog_pll_video);
+
+ reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+ reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37);
+ reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+ reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1);
+ writel(reg, &ccm->analog_pll_video);
+
+ writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
+ writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
+
+ reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
+ writel(reg, &ccm->analog_pll_video);
+
+ while (timeout--)
+ if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+ break;
+ if (timeout < 0)
+ printf("Warning: video pll lock timeout!\n");
+
+ reg = readl(&ccm->analog_pll_video);
+ reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
+ reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
+ writel(reg, &ccm->analog_pll_video);
+
+ /* select video pll for ldb_di0_clk */
+ reg = readl(&ccm->cs2cdr);
+ reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK);
+ writel(reg, &ccm->cs2cdr);
+
+ /* select ldb_di0_clk / 7 for ldb_di0_ipu_clk */
+ reg = readl(&ccm->cscmr2);
+ reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+ writel(reg, &ccm->cscmr2);
+
+ /* select ldb_di0_ipu_clk for ipu1_di0_clk -> 65MHz pixclock */
+ reg = readl(&ccm->chsccdr);
+ reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+ << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+ writel(reg, &ccm->chsccdr);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
+int board_eth_init(bd_t *bis)
+{
+ setup_iomux_enet();
+ setup_pcie();
+ return cpu_eth_init(bis);
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+ return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+ /* 4 bit bus width */
+ {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+ {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+ /* 8 bit bus width */
+ {"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
+ {NULL, 0},
+};
+#endif
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_VIDEO_IPUV3
+ setup_display();
+#endif
+#ifdef CONFIG_SYS_I2C
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+#endif
+#ifdef CONFIG_DWC_AHSATA
+ setup_sata();
+#endif
+#ifdef CONFIG_CMD_BMODE
+ add_board_boot_modes(board_boot_modes);
+#endif
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: TBS2910 Matrix ARM mini PC\n");
+ return 0;
+}
--- /dev/null
+/*
+ * Copyright (C) 2014 Soeren Moch <smoch@web.de>
+ *
+ * Configuration settings for the TBS2910 MatrixARM board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __TBS2910_CONFIG_H
+#define __TBS2910_CONFIG_H
+
+#include "mx6_common.h"
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+/* General configuration */
+#define CONFIG_MX6
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+#define CONFIG_SYS_THUMB_BUILD
+
+#define CONFIG_MACH_TYPE 3980
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SYS_GENERIC_BOARD
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MXC_GPIO
+#define CONFIG_CMD_GPIO
+
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT "Matrix U-Boot> "
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_CBSIZE 1024
+#define CONFIG_SYS_PBSIZE \
+ (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_HZ 1000
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024 * 1024)
+
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END \
+ (CONFIG_SYS_MEMTEST_START + 500 * 1024 * 1024)
+
+#define CONFIG_SYS_TEXT_BASE 0x80000000
+#define CONFIG_SYS_BOOTMAPSZ 0x6C000000
+#define CONFIG_SYS_LOAD_ADDR 0x10800000
+
+/* Serial console */
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE /* select UART1/UART2 */
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_CONS_INDEX 1
+
+/* *** Command definition *** */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_CMD_TIME
+
+/* Filesystems / image support */
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_FS_GENERIC
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_SUPPORT_RAW_INITRD
+#define CONFIG_FIT
+
+/* MMC */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_USDHC_NUM 3
+#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC4_BASE_ADDR
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+
+/* Ethernet */
+#define CONFIG_FEC_MXC
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 4
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+/* Framebuffer */
+#define CONFIG_VIDEO
+#ifdef CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_IPUV3_CLK 260000000
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_CFB_CONSOLE_ANSI
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_IMX_HDMI
+#define CONFIG_IMX_VIDEO_SKIP
+#define CONFIG_CMD_HDMIDETECT
+#endif
+
+/* PCI */
+#define CONFIG_CMD_PCI
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_PCIE_IMX
+#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12)
+#endif
+
+/* SATA */
+#define CONFIG_CMD_SATA
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE 1
+#define CONFIG_DWC_AHSATA_PORT_ID 0
+#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+#endif
+
+/* USB */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_KEYBOARD
+#ifdef CONFIG_USB_KEYBOARD
+#define CONFIG_SYS_USB_EVENT_POLL
+#define CONFIG_SYS_STDIO_DEREGISTER
+#define CONFIG_PREBOOT "if hdmidet; then usb start; fi"
+#endif /* CONFIG_USB_KEYBOARD */
+#endif /* CONFIG_CMD_USB */
+
+/* RTC */
+#define CONFIG_CMD_DATE
+#ifdef CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C
+#define CONFIG_RTC_DS1307
+#define CONFIG_SYS_RTC_BUS_NUM 2
+#endif
+
+/* I2C */
+#define CONFIG_CMD_I2C
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_I2C_EDID
+#endif
+
+/* Fuses */
+#define CONFIG_CMD_FUSE
+#ifdef CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+#endif
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+/* Flash and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 2
+#define CONFIG_SYS_MMC_ENV_PART 1
+#define CONFIG_ENV_SIZE (8 * 1024)
+#define CONFIG_ENV_OFFSET (384 * 1024)
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "bootargs_mmc1=console=ttymxc0,115200 di0_primary console=tty1\0" \
+ "bootargs_mmc2=video=mxcfb0:dev=hdmi,1920x1080M@60 " \
+ "video=mxcfb1:off video=mxcfb2:off fbmem=28M\0" \
+ "bootargs_mmc3=root=/dev/mmcblk0p1 rootwait consoleblank=0 quiet\0" \
+ "bootargs_mmc=setenv bootargs ${bootargs_mmc1} ${bootargs_mmc2} " \
+ "${bootargs_mmc3}\0" \
+ "bootargs_upd=setenv bootargs console=ttymxc0,115200 " \
+ "rdinit=/sbin/init enable_wait_mode=off\0" \
+ "bootcmd_mmc=run bootargs_mmc; mmc dev 2; " \
+ "mmc read 0x10800000 0x800 0x4000; bootm\0" \
+ "bootcmd_up1=load mmc 1 0x10800000 uImage\0" \
+ "bootcmd_up2=load mmc 1 0x10d00000 uramdisk.img; " \
+ "run bootargs_upd; " \
+ "bootm 0x10800000 0x10d00000\0" \
+ "console=ttymxc0\0" \
+ "fan=gpio set 92\0" \
+ "stdin=serial,usbkbd\0" \
+ "stdout=serial,vga\0" \
+ "stderr=serial,vga\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc rescan; " \
+ "if run bootcmd_up1; then " \
+ "run bootcmd_up2; " \
+ "else " \
+ "run bootcmd_mmc; " \
+ "fi"
+
+#endif /* __TBS2910_CONFIG_H * */
projects / u-boot.git / commitdiff