or CONFIG_VIDEO_SED13806_16BPP
CONFIG_FSL_DIU_FB
- Enable the Freescale DIU video driver. Reference boards for
+ Enable the Freescale DIU video driver. Reference boards for
SOCs that have a DIU should define this macro to enable DIU
support, and should also define these other macros:
kernel. Needed for UBI support.
- SPL framework
- CONFIG_SPL
- Enable building of SPL globally.
+ CONFIG_SPL
+ Enable building of SPL globally.
- CONFIG_SPL_TEXT_BASE
- TEXT_BASE for linking the SPL binary.
+ CONFIG_SPL_TEXT_BASE
+ TEXT_BASE for linking the SPL binary.
- CONFIG_SPL_LDSCRIPT
- LDSCRIPT for linking the SPL binary.
+ CONFIG_SPL_LDSCRIPT
+ LDSCRIPT for linking the SPL binary.
- CONFIG_SPL_LIBCOMMON_SUPPORT
- Support for common/libcommon.o in SPL binary
+ CONFIG_SPL_LIBCOMMON_SUPPORT
+ Support for common/libcommon.o in SPL binary
- CONFIG_SPL_LIBDISK_SUPPORT
- Support for disk/libdisk.o in SPL binary
+ CONFIG_SPL_LIBDISK_SUPPORT
+ Support for disk/libdisk.o in SPL binary
- CONFIG_SPL_I2C_SUPPORT
- Support for drivers/i2c/libi2c.o in SPL binary
+ CONFIG_SPL_I2C_SUPPORT
+ Support for drivers/i2c/libi2c.o in SPL binary
- CONFIG_SPL_GPIO_SUPPORT
- Support for drivers/gpio/libgpio.o in SPL binary
+ CONFIG_SPL_GPIO_SUPPORT
+ Support for drivers/gpio/libgpio.o in SPL binary
- CONFIG_SPL_MMC_SUPPORT
- Support for drivers/mmc/libmmc.o in SPL binary
+ CONFIG_SPL_MMC_SUPPORT
+ Support for drivers/mmc/libmmc.o in SPL binary
- CONFIG_SPL_SERIAL_SUPPORT
- Support for drivers/serial/libserial.o in SPL binary
+ CONFIG_SPL_SERIAL_SUPPORT
+ Support for drivers/serial/libserial.o in SPL binary
- CONFIG_SPL_SPI_FLASH_SUPPORT
- Support for drivers/mtd/spi/libspi_flash.o in SPL binary
+ CONFIG_SPL_SPI_FLASH_SUPPORT
+ Support for drivers/mtd/spi/libspi_flash.o in SPL binary
- CONFIG_SPL_SPI_SUPPORT
- Support for drivers/spi/libspi.o in SPL binary
+ CONFIG_SPL_SPI_SUPPORT
+ Support for drivers/spi/libspi.o in SPL binary
- CONFIG_SPL_FAT_SUPPORT
- Support for fs/fat/libfat.o in SPL binary
+ CONFIG_SPL_FAT_SUPPORT
+ Support for fs/fat/libfat.o in SPL binary
- CONFIG_SPL_LIBGENERIC_SUPPORT
- Support for lib/libgeneric.o in SPL binary
+ CONFIG_SPL_LIBGENERIC_SUPPORT
+ Support for lib/libgeneric.o in SPL binary
Modem Support:
--------------
writel(1 << ATMEL_ID_USART2, &pmc->pcer);
}
-
void at91_seriald_hw_init(void)
{
at91_set_a_periph(AT91_PIO_PORTA, 30, PUP); /* DRXD */
at91_set_a_periph(AT91_PIO_PORTA, 31, 1); /* DTXD */
/* writing SYS to PCER has no effect on AT91RM9200 */
}
-
return freq;
}
-
int at91_clock_init(unsigned long main_clock)
{
unsigned freq, mckr;
return 0;
}
-
{
return at91_clock_init(CONFIG_SYS_AT91_MAIN_CLOCK);
}
-
COBJS-$(CONFIG_SPL_BUILD) += foo.o
#ifdef CONFIG_SPL_BUILD
- foo();
+ foo();
#endif
3. add new structures for SoC access
4. Convert arch, driver and boards file to new SoC
5. remove legacy code, if all boards and drives are ready
-
Structure of this binary (Example for the cam_enc_4xx board with a NAND
page size = 0x800):
-offset : 0x00000 | 0x800 | 0x3800
-content: UBL | nand_spl | u-boot code
- Header | code |
+offset : 0x00000 | 0x800 | 0x3800
+content: UBL | nand_spl | u-boot code
+ Header | code |
The NAND layout looks for example like this:
(Example for the cam_enc_4xx board with a NAND page size = 0x800, block
size = 0x20000 and CONFIG_SYS_NROF_UBL_HEADER 5):
-offset : 0x80000 | 0xa0000 | 0xa3000
-content: UBL | nand_spl | u-boot code
- Header | code |
- ^ ^
- ^ 0xa0000 = CONFIG_SYS_NROF_UBL_HEADER * 0x20000
- ^
- 0x80000 = Block 4 * 0x20000
+offset : 0x80000 | 0xa0000 | 0xa3000
+content: UBL | nand_spl | u-boot code
+ Header | code |
+ ^ ^
+ ^ 0xa0000 = CONFIG_SYS_NROF_UBL_HEADER * 0x20000
+ ^
+ 0x80000 = Block 4 * 0x20000
If the cpu starts in NAND boot mode, it checks the UBL descriptor
starting with block 1 (page 0). When a valid UBL signature is found,
Once the user-specified start-up conditions are set, the RBL copies the
nand_spl into ARM internal RAM, starting at address 0x0000: 0020.
- ^^^^
+ ^^^^
The nand_spl code itself now does necessary intializations, and at least,
copies the u-boot code from NAND into RAM, and jumps to it ...
If you look at drivers/usb/eth/asix.c you will see this line within the
supported device list, so we know this adapter is supported.
- { 0x0b95, 0x7720 }, /* Trendnet TU2-ET100 V3.0R */
+ { 0x0b95, 0x7720 }, /* Trendnet TU2-ET100 V3.0R */
If your adapter is not listed there is a still a chance that it will
work. Try looking up the manufacturer of the chip inside your adapter.
support USB with CONFIG_CMD_USB enabled and working. You will need to
add some config settings to your board header file:
-#define CONFIG_USB_HOST_ETHER /* Enable USB Ethernet adapters */
-#define CONFIG_USB_ETHER_ASIX /* Asix, or whatever driver(s) you want */
+#define CONFIG_USB_HOST_ETHER /* Enable USB Ethernet adapters */
+#define CONFIG_USB_ETHER_ASIX /* Asix, or whatever driver(s) you want */
As with built-in networking, you will also want to enable some network
commands, for example:
as well as the default file to load when a 'bootp' command is issued.
All of these can be obtained from the bootp server if not set.
-#define CONFIG_IPADDR 10.0.0.2 (replace with your value)
-#define CONFIG_SERVERIP 10.0.0.1 (replace with your value)
-#define CONFIG_BOOTFILE uImage
+#define CONFIG_IPADDR 10.0.0.2 (replace with your value)
+#define CONFIG_SERVERIP 10.0.0.1 (replace with your value)
+#define CONFIG_BOOTFILE uImage
The 'usb start' command should identify the adapter something like this:
Filename '/tftpboot/uImage-sjg-seaboard-261347'.
Load address: 0x40c000
Loading: #################################################################
- #################################################################
- #################################################################
- ################################################
+ #################################################################
+ #################################################################
+ ################################################
done
Bytes transferred = 3557464 (364858 hex)
CrOS>
#include <asm/arch/hardware.h>
#include <asm/arch/davinci_misc.h>
-
static struct gpio_registry {
int is_registered;
char name[GPIO_NAME_SIZE];
} gpio_registry[MAX_NUM_GPIOS];
-
#define pinmux(x) (&davinci_syscfg_regs->pinmux[x])
static const struct pinmux_config gpio_pinmux[] = {
{ pinmux(18), 8, 2 },
};
-
-
int gpio_request(int gp, const char *label)
{
if (gp >= MAX_NUM_GPIOS)
return 0;
}
-
void gpio_free(int gp)
{
gpio_registry[gp].is_registered = 0;
}
-
void gpio_toggle_value(int gp)
{
struct davinci_gpio *bank;
gpio_set_value(gp, !gpio_get_value(gp));
}
-
int gpio_direction_input(int gp)
{
struct davinci_gpio *bank;
return 0;
}
-
int gpio_direction_output(int gp, int value)
{
struct davinci_gpio *bank;
return 0;
}
-
int gpio_get_value(int gp)
{
struct davinci_gpio *bank;
return ip ? 1 : 0;
}
-
void gpio_set_value(int gp, int value)
{
struct davinci_gpio *bank;
bank->clr_data = 1U << GPIO_BIT(gp);
}
-
void gpio_info(void)
{
int gp, dir, val;
MDIO_DEVS_DTEXS | \
MDIO_DEVS_AN)
-
-
/* Control register 2. */
#define MDIO_PMA_CTRL2_TYPE 0x000f /* PMA/PMD type selection */
#define MDIO_PMA_CTRL2_10GBCX4 0x0000 /* 10GBASE-CX4 type */
projects / u-boot.git / commitdiff