From: Chris Packham Date: Mon, 25 Nov 2024 19:55:53 +0000 (+1300) Subject: arm: mvebu: Add Allied Telesis x250 board X-Git-Url: http://git.dujemihanovic.xyz/%22mailto:Murray.Jensen%40csiro.au/static/git-logo.png?a=commitdiff_plain;h=7446e29db54818324859126739c3477a15d25c36;p=u-boot.git arm: mvebu: Add Allied Telesis x250 board The x250 and SE250 are series of 10G L2+ switches from Allied Telesis. There are a number of them in the range but as far as U-Boot is concerned all the CPU block components are the same so there's only one board defined. Signed-off-by: Chris Packham Reviewed-by: Stefan Roese --- diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 042282f372..6ad59aeed5 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -190,7 +190,8 @@ dtb-$(CONFIG_ARCH_MVEBU) += \ cn9130-crb-A.dtb \ cn9130-crb-B.dtb \ ac5-98dx35xx-rd.dtb \ - ac5-98dx35xx-atl-x240.dtb + ac5-98dx35xx-atl-x240.dtb \ + cn9130-atl-x250.dtb endif dtb-$(CONFIG_ARCH_SYNQUACER) += synquacer-sc2a11-developerbox.dtb diff --git a/arch/arm/dts/cn9130-atl-x250.dts b/arch/arm/dts/cn9130-atl-x250.dts new file mode 100644 index 0000000000..f2c82da9d1 --- /dev/null +++ b/arch/arm/dts/cn9130-atl-x250.dts @@ -0,0 +1,274 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2024 Allied Telesis Labs + */ + +#include "cn9130.dtsi" + +/ { + model = "Allied Telesis x250"; + compatible = "alliedtelesis,x250", + "marvell,cn9130", + "marvell,armada-ap806-quad", + "marvell,armada-ap806"; + + aliases { + serial0 = &uart0; + i2c0 = &cp0_i2c0; + i2c1 = &cp0_i2c1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-leds { + compatible = "gpio-leds"; + + fault { + label = "fault:red"; + gpios = <&cp0_gpio1 9 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + }; +}; + +/* + * AP related configuration + */ +&ap_pinctl { + /* AP_MPP Pins: + * GPIO & NC [0-6,9-10,12] + * UART0 [11,19] + * UART1 [7,8] + * Note: The x250-28XTm PT1 units has the console port wired + * to the second uart pins (UART1). This was fixed in all + * subsequent models. + * Here we choose to configure the pin control for both + * uarts to cater for either unit. + */ + /* 0 1 2 3 4 5 6 7 8 9 */ + pin-func = < 0 0 0 0 0 0 0 3 3 0 + 0 3 0 0 0 0 0 0 0 3 >; +}; + +&ap_gpio0 { + pp-reset { + gpio-hog; + gpios = <0 GPIO_ACTIVE_LOW>; + output-high; + line-name = "pp-reset"; + }; +}; + +/* + * CP related configuration + */ +&cp0_pinctl { + /* MPP Bus: + * [0-1] DEV + * [2-8] GPIO + * [9] DEV + * [10-12] GPIO + * [13] ND_RB + * [14] GPIO + * [15-28] DEV + * [29-30] GPIO + * [31] DEV + * [32-34] GPIO + * [35-36] I2C1 + * [37-38] I2C0 + * [39-55] GPIO + * [56-60] SPI + * [61-62] GPIO + */ + /* 0 1 2 3 4 5 6 7 8 9 */ + pin-func = < 1 1 0 0 0 0 0 0 0 1 + 0 0 0 2 0 1 1 1 1 1 + 1 1 1 1 1 1 1 1 1 0 + 0 1 0 0 0 2 2 2 2 0 + 0 0 0 0 0 0 0 0 0 0 + 0 0 0 0 0 0 6 6 6 6 + 6 0 0>; + + cp0_i2c0_pins: cp0-i2c-pins-0 { + marvell,pins = <37 38>; + marvell,function = <2>; + }; + + cp0_i2c0_gpio_pins: cp0-i2c-gpio-pins-0 { + marvell,pins = <37 38>; + marvell,function = <0>; + }; + + cp0_i2c1_pins: cp0-i2c-pins-1 { + marvell,pins = <35 36>; + marvell,function = <2>; + }; + + cp0_nand_pins: cp0-nand-pins { + marvell,pins = <0 1 9 15 16 17 18 19 20 21 22 23 24 25 26 27 28 31>; + marvell,function = <1>; + }; + + cp0_nand_rb: cp0-nand-rb { + marvell,pins = <13>; + marvell,function = <2>; + }; + + cp0_spi0_pins: cp0-spi-pins-0 { + marvell,pins = <56 57 58 59 60>; + marvell,function = <6>; + }; +}; + +&cp0_comphy { + phy0 { + phy-type = ; + }; + + phy1 { + phy-type = ; + }; + + phy2 { + phy-type = ; + }; + + phy3 { + phy-type = ; + }; + + phy4 { + phy-type = ; + }; + + phy5 { + phy-type = ; + }; +}; + +&cp0_pcie0 { + num-lanes = <1>; + /* non-prefetchable memory */ + ranges =<0x82000000 0 0xc0000000 0 0xc0000000 0 0x2000000>; + status = "disabled"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + clock-frequency = <200000000>; +}; + +&cp0_utmi0 { + status = "okay"; +}; + +&cp0_usb3_0 { + status = "okay"; +}; + +&cp0_spi0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_spi0_pins>; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <50000000>; + m25p,fast-read; + }; +}; + +&cp0_nand { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_nand_pins &cp0_nand_rb>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-timing-mode = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@user { + reg = <0x00000000 0x10000000>; + label = "user"; + }; + }; +}; + +&cp0_gpio0 +{ + nand-protect { + gpio-hog; + gpios = <29 GPIO_ACTIVE_LOW>; + output-low; + line-name = "nand-protect"; + }; +}; + +&cp0_gpio1 +{ + usb-en { + gpio-hog; + gpios = <0 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb-en"; + }; + + phy-reset { + gpio-hog; + gpios = <21 GPIO_ACTIVE_LOW>; + output-high; + line-name = "phy-reset"; + }; +}; + +&cp0_i2c0 { + status = "okay"; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&cp0_i2c0_pins>; + pinctrl-1 = <&cp0_i2c0_gpio_pins>; + scl-gpios = <&cp0_gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&cp0_gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + + mux@71 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "nxp,pca9546"; + reg = <0x71>; + i2c-mux-idle-disconnect; + reset-gpios = <&cp0_gpio1 19 GPIO_ACTIVE_LOW>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + hwmon@2e { + compatible = "adi,adt7476"; + reg = <0x2e>; + }; + + rtc@68 { + compatible = "adi,max31331"; + reg = <0x68>; + }; + }; + }; +}; + +&cp0_i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_i2c1_pins>; +}; diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index b61253e2d0..adb816982f 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -215,6 +215,12 @@ config TARGET_X530 bool "Support Allied Telesis x530" select 88F6820 +config TARGET_X250 + bool "Support Allied Telesis x250" + select ARMADA_8K + imply SCSI + imply BOOTSTD_DEFAULTS + config TARGET_X240 bool "Support Allied Telesis x240" select ALLEYCAT_5 @@ -302,6 +308,7 @@ config SYS_BOARD default "theadorable" if TARGET_THEADORABLE default "a38x" if TARGET_CONTROLCENTERDC default "x530" if TARGET_X530 + default "x250" if TARGET_X250 default "x240" if TARGET_X240 default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236 @@ -326,6 +333,7 @@ config SYS_CONFIG_NAME default "turris_mox" if TARGET_TURRIS_MOX default "controlcenterdc" if TARGET_CONTROLCENTERDC default "x530" if TARGET_X530 + default "x250" if TARGET_X250 default "x240" if TARGET_X240 default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236 @@ -350,6 +358,7 @@ config SYS_VENDOR default "CZ.NIC" if TARGET_TURRIS_MOX default "gdsys" if TARGET_CONTROLCENTERDC default "alliedtelesis" if TARGET_X530 + default "alliedtelesis" if TARGET_X250 default "alliedtelesis" if TARGET_X240 default "mikrotik" if TARGET_CRS3XX_98DX3236 default "Marvell" if TARGET_MVEBU_ALLEYCAT5 diff --git a/board/alliedtelesis/x250/MAINTAINERS b/board/alliedtelesis/x250/MAINTAINERS new file mode 100644 index 0000000000..8a74dbc68b --- /dev/null +++ b/board/alliedtelesis/x250/MAINTAINERS @@ -0,0 +1,7 @@ +X250 BOARD +M: Chris Packham +S: Maintained +F: board/alliedtelesis/x250/ +F: arch/arm/dts/cn9130-atl-x250.dts +F: include/configs/x250.h +F: configs/x250_defconfig diff --git a/board/alliedtelesis/x250/Makefile b/board/alliedtelesis/x250/Makefile new file mode 100644 index 0000000000..98e0ccedde --- /dev/null +++ b/board/alliedtelesis/x250/Makefile @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2024 Allied Telesis +# + +obj-y += x250.o diff --git a/board/alliedtelesis/x250/x250.c b/board/alliedtelesis/x250/x250.c new file mode 100644 index 0000000000..66c782698f --- /dev/null +++ b/board/alliedtelesis/x250/x250.c @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#define DEVICE_BUS_SYNC_CTRL 0xF27004C8 + +int board_init(void) +{ + gd->bd->bi_boot_params = CFG_SYS_SDRAM_BASE + 0x100; + + /* DEV_READYn is not needed for NVS, ignore it when accessing CS1 */ + writel(0x00004001, DEVICE_BUS_SYNC_CTRL); + + return 0; +} diff --git a/configs/x250_defconfig b/configs/x250_defconfig new file mode 100644 index 0000000000..dffe85bd6e --- /dev/null +++ b/configs/x250_defconfig @@ -0,0 +1,104 @@ +CONFIG_ARM=y +CONFIG_ARCH_CPU_INIT=y +CONFIG_ARCH_MVEBU=y +CONFIG_TEXT_BASE=0x00000000 +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 +CONFIG_TARGET_X250=y +CONFIG_ENV_SIZE=0x10000 +CONFIG_ENV_OFFSET=0xf80000 +CONFIG_ENV_SECT_SIZE=0x40000 +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="cn9130-atl-x250" +CONFIG_SYS_LOAD_ADDR=0x10000000 +CONFIG_DEBUG_UART_BASE=0xf0512000 +CONFIG_DEBUG_UART_CLOCK=200000000 +CONFIG_PCI=y +CONFIG_DEBUG_UART=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_FIT=y +CONFIG_FIT_SIGNATURE=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_BOOTCOMMAND="run distro_bootcmd" +CONFIG_USE_PREBOOT=y +CONFIG_SPL_SILENT_CONSOLE=y +CONFIG_TPL_SILENT_CONSOLE=y +CONFIG_SYS_CONSOLE_INFO_QUIET=y +# CONFIG_DISPLAY_CPUINFO is not set +# CONFIG_DISPLAY_BOARDINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MTD=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_TFTPPUT=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_UBI=y +CONFIG_MAC_PARTITION=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_SYS_MMC_ENV_DEV=1 +CONFIG_ARP_TIMEOUT=200 +CONFIG_NET_RETRY_COUNT=50 +CONFIG_IPV6=y +CONFIG_SYS_64BIT_LBA=y +CONFIG_GPIO_HOG=y +CONFIG_DM_I2C=y +CONFIG_DM_I2C_GPIO=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y +# CONFIG_INPUT is not set +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_MISC=y +# CONFIG_MMC is not set +CONFIG_MTD_RAW_NAND=y +CONFIG_SYS_NAND_USE_FLASH_BBT=y +CONFIG_NAND_PXA3XX=y +CONFIG_SYS_NAND_ONFI_DETECTION=y +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_ATMEL=y +CONFIG_SPI_FLASH_GIGADEVICE=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_SST=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_PHY_MARVELL=y +CONFIG_PHY_GIGE=y +CONFIG_E1000=y +CONFIG_MVPP2=y +CONFIG_NVME_PCI=y +CONFIG_PCIE_DW_MVEBU=y +CONFIG_PHY=y +CONFIG_MVEBU_COMPHY_SUPPORT=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_ARMADA_8K=y +CONFIG_DM_RTC=y +CONFIG_RTC_DS1307=y +CONFIG_RTC_MAX313XX=y +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_SYS_NS16550=y +CONFIG_KIRKWOOD_SPI=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +CONFIG_USB_ETHER_ASIX88179=y +CONFIG_USB_ETHER_MCS7830=y +CONFIG_USB_ETHER_RTL8152=y +CONFIG_USB_ETHER_SMSC95XX=y +# CONFIG_TOOLS_MKEFICAPSULE is not set diff --git a/include/configs/x250.h b/include/configs/x250.h new file mode 100644 index 0000000000..39f523fa6c --- /dev/null +++ b/include/configs/x250.h @@ -0,0 +1,28 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2024 Allied Telesis + */ + +#ifndef __X250_H_ +#define __X250_H_ + +/* + * High Level Configuration Options (easy to change) + */ +#define CFG_SYS_TCLK 250000000 /* 250MHz */ + +/* additions for new ARM relocation support */ +#define CFG_SYS_SDRAM_BASE 0x00000000 + +#define BOOT_TARGETS "usb scsi pxe dhcp" + +#define CFG_EXTRA_ENV_SETTINGS \ + "scriptaddr=0x6d00000\0" \ + "pxefile_addr_r=0x6e00000\0" \ + "fdt_addr_r=0x6f00000\0" \ + "kernel_addr_r=0x7000000\0" \ + "ramdisk_addr_r=0xa000000\0" \ + "fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \ + "boot_targets=" BOOT_TARGETS "\0" + +#endif /* __X250_H_ */