Wenyou Yang [Tue, 18 Apr 2017 05:49:35 +0000 (13:49 +0800)]
ARM: dts: at91: Add dts files for at91sam9n12ek
The device tree source files of at91sam9n12ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the pinctrl-names of mmc0 node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Tue, 18 Apr 2017 05:49:34 +0000 (13:49 +0800)]
ARM: dts: at91: Add dts files for at91sam9x5ek
The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Fri, 14 Apr 2017 07:01:27 +0000 (15:01 +0800)]
serial: atmel_usart: Fix early debug not work in SPL
Add the uart init function to be used on both probe and the early
debug uart init. For the latter, the input clock should be from
CONFIG_DEBUG_UART_CLOCK.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Fri, 14 Apr 2017 06:36:04 +0000 (14:36 +0800)]
net: macb: Add remove callback
To avoid the failure of mdio_register(), add the remove callback
to unregister the mii_dev when removing the ethernet device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fixed up unused variable warning, e.g. for gurnard: Signed-off-by: Simon Glass <sjg@chromium.org>
Wenyou Yang [Fri, 24 Mar 2017 01:26:16 +0000 (09:26 +0800)]
configs: sama5d3xek: add default config for CMP board
The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865, and
some power rails. The board is mainly used to measure the power
consumption. As all those changes are done in at91bootstrap,
in U-Boot, only use another device tree file, no code needed
to change.
As there is additional power consumption when enbling the USB
Host and USB device, for the power consumption measurement
intention, disable the USB host and device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Thu, 23 Mar 2017 06:26:28 +0000 (14:26 +0800)]
configs: sama5d2_xplained: update for SPL
Enable config options to support the SPL, increase the malloc
memory size for the SPL and board_init_f stage and increase
the memory space for the SPL binary.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Wenyou Yang [Thu, 23 Mar 2017 06:26:25 +0000 (14:26 +0800)]
board: sama5d2_xplained: clean up macb init code
Because the MACB driver supports the driver model and device tree,
the pins configuration and clock enabling are handled by the
pinctrl driver and clock driver, remove this hardcoded init code.
The USB Ether init code is removed as well.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Maxim Sloyko [Tue, 9 May 2017 13:08:07 +0000 (09:08 -0400)]
dm: Update Simple Watchdog uclass
- Remove "probe" function from sandbox wdt driver
- Fix include order
Fixes: 0753bc2d30d7 ("dm: Simple Watchdog uclass") Signed-off-by: Maxim Sloyko <maxims@google.com>
[trini: Create as the delta between v1 (applied) and v2 (should have
applied)]. Signed-off-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Wed, 3 May 2017 11:28:26 +0000 (16:58 +0530)]
ARM: keystone2: Add support for getting external clock dynamically
One some keystone2 platforms like K2G ICE, there is an option
to switch between 24MHz or 25MHz as sysclk. But the existing
driver assumes it is always 24MHz. Add support for getting
all reference clocks dynamically by reading boot pins.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Wed, 3 May 2017 11:28:25 +0000 (16:58 +0530)]
ARM: k2g: Add support for dynamic programming of PLL based on SYSCLK
K2G supports various sysclk frequencies which can be
determined using sysboot pins. PLLs should be configured
based on this sysclock frequency. Add PLL configurations
for all supported sysclk frequencies.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
board: ti: Define Kconfig symbol for common cmd options
Instead of defining command options in every defconfig,
define a common Kconfig symbol that consolidates all command
options that are supported by any TI platform. Also use imply
keyword so that that specific option can be disabled if
not required.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Add ARM errata workaround 852421 and 852423 for Cortex-A17
ARM errata 852421 and 852423 applies to r1p0, r1p1 and r1p2
revisions of Cortex-A17 processors. These workarounds
exist in Linux kernel and I thought it would be better
to add them in to U-Boot.
Add support for clocks needed by MACs to ast2500 clock driver.
The clocks are D2-PLL, which is used by both MACs and PCLK_MAC1 and
PCLK_MAC2 for MAC1 and MAC2 respectively.
The rate of D2-PLL is hardcoded to 250MHz -- the value used in Aspeed
SDK. It is not entirely clear from the datasheet how this clock is used
by MACs, so not clear if the rate would ever need to be different. So,
for now, hardcoding it is probably safer.
The rate of PCLK_MAC{1,2} is chosen based on MAC speed selected through
hardware strapping.
So, the network driver would only need to enable these clocks, no need
to configure the rate.
Signed-off-by: Maxim Sloyko <maxims@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Add Device Model based I2C driver for ast2500/ast2400 SoCs.
The driver is very limited, it only supports master mode and
synchronous byte-by-byte reads/writes, no DMA or Pool Buffers.
This driver uses Generic Pinctrl framework and is compatible with
the Linux driver for ast2500: it uses the same device tree
configuration.
Not all pins are supported by the driver at the moment, so it actually
compatible with ast2400. In general, however, there are differences that
in the future would be easier to maintain separately.
Signed-off-by: Maxim Sloyko <maxims@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
aspeed: Refactor AST2500 RAM Driver and Sysreset Driver
This change switches all existing users of ast2500 Watchdog to Driver
Model based Watchdog driver.
To perform system reset Sysreset Driver uses first Watchdog device found
via uclass_first_device call. Since the system is going to be reset
anyway it does not make much difference which watchdog is used.
Instead of using Watchdog to reset itself, SDRAM driver now uses Reset
driver to do that.
These were the only users of the old Watchdog API, so that API is
removed.
This all is done in one change to avoid having to maintain dual API for
watchdog in between.
Signed-off-by: Maxim Sloyko <maxims@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Add Reset Driver for ast2500 SoC. This driver uses Watchdog Timer to
perform resets and thus depends on it. The actual Watchdog device used
needs to be configured in Device Tree using "aspeed,wdt" property, which
must be WDT phandle, for example:
aspeed: Make SCU lock/unlock functions part of SCU API
Make functions for locking and unlocking SCU part of SCU API.
Many drivers need to modify settings in SCU and thus need to unlock it
first. This change makes it possible.
Signed-off-by: Maxim Sloyko <maxims@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
This is a simple uclass for Watchdog Timers. It has four operations:
start, restart, reset, stop. Drivers must implement start, restart and
stop operations, while implementing reset is optional: It's default
implementation expires watchdog timer in one clock tick.
Signed-off-by: Maxim Sloyko <maxims@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Pull in the Device Tree for ast2500 from the mainline Linux kernel.
The file is copied from
https://raw.githubusercontent.com/torvalds/linux/34ea5c9d/arch/arm/boot/dts/aspeed-g5.dtsi
Signed-off-by: Maxim Sloyko <maxims@google.com> Reviewed-by: Simon Glass <sjg@chromium.org>
ARM: DT: STM32F746: add u-boot, dm-pre-reloc property to sub nodes
This patch is required for correct SPL device tree creation by fdtgrep
as fdtgrep looks for u-boot,dm-pre-reloc property of the node to include
it in the spl device tree.
Not adding it in these subnodes ignores the pin muxing of peripherals
which is almost always in the subnodes.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Chris Packham [Tue, 2 May 2017 09:30:47 +0000 (21:30 +1200)]
tools: moveconfig: cleanup whitelist entries
After moving to KConfig and removing from all headers options should be
removed from config_whitelist.txt so the build starts complaining if
someone adds them back.
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
The IGEP SMARC AM335x is an industrial processor module with
following highlights:
o AM3352 TI processor (Up to AM3359)
o Cortex-A8 ARM CPU
o SMARC form factor module
o Up to 512 MB DDR3 SDRAM / 512 MB FLASH
o WiFi a/b/g/n and Bluetooth v4.0 on-board
o Ethernet 10/100/1000 Mbps and 10/100 Mbps controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Ladislav Michl [Sat, 1 Apr 2017 15:17:57 +0000 (17:17 +0200)]
igep003x: UBIize
Convert IGEP board to use UBI volumes for U-Boot, its environment and
kernel. With exception of first four sectors read by SoC BootROM whole
NAND is UBI managed.
nand_spl_load_image implementation was copied over into three
different drivers and now with nand_spl_read_block used for
ubispl situation gets even worse. For now use least intrusive
solution and #include the same implementation to nand drivers.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Tested-by: Pau Pajuelo <ppajuel@gmail.com>
This board support stm32f7 family device stm32f769-I with 2MB internal Flash &
512KB RAM.
STM32F769 lines offer the performance of the Cortex-M7 core (with double
precision floating point unit) running up to 216 MHz.
To compile for stm32f769 board, use same defconfig as stm32f746-disco,
the only difference is to pass "DEVICE_TREE=stm32f769-disco".
stm32f7: increase the max no of pin configuration to 70
The number of pins to be configured could be more than 50 e.g. in case
of sdram controller, there are about 56 pins (32 data lines, 12 address
& some control signals).
stm32f7: sdram: correct sdram configuration as per micron sdram
Actually the sdram memory on stm32f746 discovery board is micron part
MT48LC_4M32_B2B5_6A. This patch does the modification required in the
device tree node & driver for the same.
Also we are passing here all the timing parameters in terms of clock
cycles, so no need to convert time(ns or ms) to cycles.
stm32f7: use stm32f7 gpio driver supporting driver model
With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.
Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.
spl: make image arg or fdt blob address reconfigurable
At present fdt blob or argument address being passed to kernel is fixed at
compile time using macro CONFIG_SYS_SPL_ARGS_ADDR. FDT blob from
different media like nand, nor flash are copied to the address pointed
by the macro.
The problem is, it makes args/fdt blob compulsory to copy which is not required
in cases like for NOR Flash. This patch removes this limitation.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Igor Grinberg <grinberg@compulab.co.il>
Uri Mashiach [Thu, 23 Feb 2017 13:39:38 +0000 (15:39 +0200)]
arm: am57xx: cl-som-am57x: invoke clock API to enable/disable clocks
Invoke enable_usb_clocks during board_usb_init and disable_usb_clocks
during board_usb_exit to enable and disable clocks respectively.
Modifications:
* Enable USB clocks in the OMAP version of the function
board_usb_init.
* Disable USB clocks in the OMAP version of the function
board_usb_cleanup.
Cc: Marek Vasut <marex@denx.de> Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
A weak version of the function board_usb_init is implemented in:
common/usb.c
drivers/usb/host/xhci-omap.c
To fix the double implementations:
* Convert the board_usb_init function in drivers/usb/host/xhci-omap.c
normal (not weak).
* The function board_usb_init in drivers/usb/host/xhci-omap.c calls to
the weak function omap_xhci_board_usb_init.
* Rename board version of the function board_usb_init to
omap_xhci_board_usb_init.
Done only for boards that defines CONFIG_USB_XHCI_OMAP.
To achieve the same flexibility with the function board_usb_cleanup:
* Add a normal (not weak) implementation of the function
board_usb_cleanup in drivers/usb/host/xhci-omap.c
* The function board_usb_cleanup in drivers/usb/host/xhci-omap.c calls
to the weak function omap_xhci_board_usb_cleanup.
* Rename board version of the function board_usb_cleanup to
omap_xhci_board_usb_cleanup.
Done only for boards that defines CONFIG_USB_XHCI_OMAP.
Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Acked-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Roger Quadros <rogerq@ti.com>
Uri Mashiach [Thu, 23 Feb 2017 13:39:36 +0000 (15:39 +0200)]
arm: usb: dra7xx: xHCI registers based on USB port index
Modify the determination of the base address of xHCI registers of DRA7XX
targets.
Before the commit: by the target.
After the commit: by the USB port index.
Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Marek Vasut <marex@denx.de> Cc: Roger Quadros <rogerq@ti.com> Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Roger Quadros <rogerq@ti.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
According to the C99 standard endptr in the first strtol is always
set as &endptr is not NULL.
So the first part of the or condition is always true.
If all digits in optarg are valid endptr will point to the closing \0
and the second strtol will read beyond the end of the string optarg
points to.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A feature rich Linux kernel needs more than 8 MiB.
Hence enlarge CONFIG_SYS_BOOTM_LEN to 64 MiB for the GXBB systems.
As all known GXBB systems have at least 512 MiB of RAM this poses no problem.
Cc: Andreas Färber <afaerber@suse.de> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Suniel Mahesh [Wed, 3 May 2017 06:17:29 +0000 (11:47 +0530)]
drivers: spi: Remove duplicate .probe method
.probe method has been assigned twice when declaring
a driver with U_BOOT_DRIVER(). Removed one of them.
Here is the last commit which had the duplicate entry:
"spi: omap3: Convert to driver model"
(sha1: 77b8d04854f486741471ad02b93b473b5b3d72f8)
Signed-off-by: Suniel Mahesh <suniel.spartan@gmail.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Andreas Fenkart [Sat, 8 Apr 2017 09:59:34 +0000 (11:59 +0200)]
env_sf: use DIV_ROUND_UP to calculate number of sectors to erase
simpler to read
Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com>
Andreas Fenkart [Sat, 8 Apr 2017 09:59:33 +0000 (11:59 +0200)]
env_sf: re-order error handling in single-buffer env_relocate_spec
this makes it easier comparable to the double-buffered version
Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com>
Andreas Fenkart [Sat, 8 Apr 2017 09:59:32 +0000 (11:59 +0200)]
enf_sf: reuse setup_flash_device instead of open coding it
setup_flash_device selects one of two code paths depending on the driver
model being used (=CONFIG_DM_SPI_FLASH). env_relocate_spec only used
the non driver-model code path. I'm unsure why, either none of the
platforms that need relocation use the driver model, or - worse - the
driver model is not yet usable when relocating.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com>
Andreas Fenkart [Sat, 8 Apr 2017 09:59:31 +0000 (11:59 +0200)]
env_sf: factor out prepare_flash_device
copy&paste code found in single/double buffered code path
Signed-off-by: Andreas Fenkart <afenkart@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com>
projects / u-boot.git / log
