arm: xea: dts: Add 'fec-3v3' regulator properties to prevent accidental disablement

The 'enable-active-high' DTS property configures GPIO so it is active with
HIGH state (by default it is low).

The 'regulator-boot-on' property indicates that the regulator was enabled
in the 'earlier' stage - i.e. bootloader/firmware.
In the XEA case the 'fec-3v3' was configured (as a "wrapper" on GPIO0_0) in
very early SPL code, so it shouldn't be modified at latter stages.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

arm: xea: spl: Add GPIO0_0 setup on spl_board_init

Explicitly configure GPIO0_0 in SPL, which controlls 3V3 voltage
on the XEA board (it also supplies TIVAs).

This code would enable TIVAs power supply early (also when board
uses the falcon boot).

Signed-off-by: Lukasz Majewski <lukma@denx.de>

arm: xea: config: Enable support for XEA board specific device tree tweaks

This patch enables support for CONFIG_OF_BOARD_SETUP in xea defconfig.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

arm: xea: Provide function to set L2 switch 'local-mac-address' property

The 'local-mac-address' property needs to be adjusted to the MAC address
value stored in U-Boot's 'ethaddr' env variable.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

arm: xea: defconfig: Define space for redundant envs in SPI-NOR flash

Redundant envs help with assuring better reliability for the system as they
prevent from the situation when envs are stored only in a single place.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

mx7ulp_com: Remove unneeded SoC definitions

Since commit 9c27310ac23c ("mx7ulp: Move SoC base address to a common
file") we no longer need to have these SoC definitions in the board
file, so remove them.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>

cmd: mdc/mwc: normalize disjoint MX_CYCLIC usage

Both CMD_MX_CYCLIC and MX_CYCLIC are in use and defined in Kconfig,
but only the non-CMD version currently does anything. This changes all
usages to prefer the CMD_MX_CYCLIC option (since it's only affecting
addition of the commands), and switches defconfigs using the non-CMD
version to use the CMD version.

Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Tom Rini <trini@konsulko.com>

tools: imx8m_image: fix warning message

When a firmware file is missing the warning message doesn't indicate the
firmware file name because '$tmp' var doesn't exist.
Fix the warning message and while at it reduce the if/else statement.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>

mx6sxsabresd: Keep only one target

Currently there are two targets for the i.MX6SX SabreSD board:
mx6sxsabresd_defconfig and mx6sxsabresd_spl_defconfig.

This brings additional maintainance effort without a clear
advantage.

Keep only the mx6sxsabresd_defconfig one and remove
mx6sxsabresd_spl_defconfig to keep it simpler.

Also remove the SPL related code from the board file.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>

mx6ul_14x14_evk: Move CONFIG_DM_74X164 to defconfig

The CONFIG_DM_74X164 symbols should be moved to the defconfig file,
as indicated in the comments.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

gpio: Let DM_74X164 be built without CONFIG_SPL_GPIO

Since commit bcee8d6764f9 ("dm: gpio: Allow control of GPIO uclass in SPL")
CONFIG_DM_74X164 is no longer built for mx7dsabresd_defconfig, as
this target does not use CONFIG_SPL_GPIO.

Remove such dependency and let the the 74X164 GPIO driver be built
again.

This restores Ethernet functionality on the imx7-sdb board as the
Ethernet reset PHY comes from a GPIO driven by a 74LV595PW I/O
expander.

Fixes: bcee8d6764f9 ("dm: gpio: Allow control of GPIO uclass in SPL")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Alifer Moraes <alifer.wsdm@gmail.com>

imx: imx8mm_evk: spelling in readme file

Minor spelling fix in README file.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

board: toradex: verdin-imx8mm: add MAINTAINERS

Assign Igor Opaniuk as a board maintainer.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

board: toradex: verdin-imx8mm: add README

Add README with build steps for U-boot and TF-A for Verdin iMX8M Mini SoM.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

board: toradex: Add Verdin iMX8M Mini support

This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.

Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C

Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper

ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.

Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE:  Configuring TZASC380
NOTICE:  RDC off
NOTICE:  BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE:  BL31: Built : 01:11:41, Jan 25 2020
NOTICE:  sip svc init

U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)

CPU:   Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM:  2 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial
Out:   serial
Err:   serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
 06535149
Net:   eth0: ethernet@30be0000
Hit any key to stop autoboot:  0
Verdin iMX8MM #

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

toradex: tdx-cfg-block: add Verdin iMX8M Mini/Nano support

Add support for storing configuration for Verdin iMX8M Mini and
Nano SoMs in Toradex config block.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

toradex: tdx-cfg-block: add Apalis iMX8X support

Add support for storing configuration for Apalis iMX8X SoM
in Toradex config block.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

arm: dts: imx8mm-pinfunc: sync latest linux-next pin func header

Synchronise with latest linux-next kernel pin func header file.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

Merge branch '2020-02-07-master-imports'

- 2 FAT fixes.
- MediaTek ethernet support improvement.
- Initial Cortina Access CAxxxx family support.
- Correct return value of do_gpio() and so gpio shell command.

board: presidio-asic: Add basic G3 engr. development board support

Add basic Presidio G3 engineering board support

Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

serial: serial_cortina: add UART DM driver for CAxxxx SoCs

Add serial UART driver support for all Cortina Access
CAxxxx family of SoCs.

Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

watchdog: cortina_wdt: add support for HW WDT on CAxxxx SoCs

Add support for hardware watchdog timer on all Cortina Access
CAxxxx family of SoCs.

Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

gpio: cortina_gpio: add DM_GPIO driver for CAxxxx SoCs

DM_GPIO based GPIO controller driver for CAxxxx SoCs.
This driver support multiple CPU architectures and
Cortina Access SoC platforms.

Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

gpio: do not include <asm/arch/gpio.h> for Cortina CAxxxx SoCs

The Cortina CAxxxx GPIO driver maintains DM_GPIO support
across different CPU ISA in the CAxxxx Soc Family; Not just ARM.
Therefore, it is not desirable to split out and maintain separete
gpio header file for each CPU architecture.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

MAINTAINERS, git-mailrc: cortina: add Custodian for Cortina Access Inc.

Assign Alex Nemirovsky as custodian for all
Cortina Access (CA) for ARM and MIPS based SoCs.

Currently Cortina Access CAxxxx family of SoCs support both
ARM and MIPS ISA.  Drivers have cross platform support for
both architectures.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

mpc8xx: Expose show_regs()

To match the other PowerPC platforms the function show_regs() must not
be marked static but instead be an exposed global function.

Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Christophe Leroy <christophe.leroy@c-s.fr>

cmd/elf.c: Add SPDX tag

Based on reading the text of the license comment this appears to be
the BSD-2-Clause license but with an imperfect word match as
BSD-2-Clause was not (as far as I recall) a common license choice at the
time the code was written.

Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

configs: mediatek: enable mt7622 ethernet support

This patch enable mt7622 ethernet support in its defconfig

Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>

eth: mtk-eth: aarch64: fix build warnings on ethernet-driver

building mtk ethernet driver for aarch64 (mt7622) results
in warnings/errors

  "error: cast from pointer to integer of different size"

Fixes: 23f17164d9 ("ethernet: MediaTek: add ethernet driver for MediaTek ARM-based SoCs")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>

arm: dts: mediatek: add ethernet and sgmii dts node for mt7622

This patch add eth and sgmii dts node for mt7622 to support ethernet

Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>

eth: mtk-eth: add mt7622 support in mediatek eth driver

This patch add mt7622 support in mediatek eth driver

Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>

eth: mtk-eth: add sgmii mode support in mediatek eth driver

This patch add sgmii init part for the mediatek SoC that
support sgmii mode. It is a must for mt7622.

Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>

fat: write: adjust data written in each partial write

The code for handing file overwrite incorrectly calculated the amount of
data to write when writing to the last non-cluster aligned chunk. Fix
this by ensuring that no more data than the 'filesize' is written to disk.
While touching min()-based calculations, change it to type-safe min_t()
function.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch finally fixes the issue revealed by the test script from the
previous patch. The correctness of the change has been also verified by
the following additional test scripts:

--->8-fat_test2.sh---
#!/bin/bash
make sandbox_defconfig
make
dd if=/dev/zero of=/tmp/10M.img bs=1024 count=10k
mkfs.vfat -v /tmp/10M.img
cat >/tmp/cmds <<EOF
x
host bind 0 /tmp/10M.img
fatls host 0
mw 0x1000000 0x0a434241 0x1000 # "ABC\n"
mw 0x1100000 0x0a464544 0x8000 # "DEF\n"
fatwrite host 0 0x1000000 file0001.raw 0x1000
fatwrite host 0 0x1000000 file0002.raw 0x1000
fatwrite host 0 0x1000000 file0003.raw 0x1000
fatwrite host 0 0x1000000 file0004.raw 0x1000
fatwrite host 0 0x1000000 file0005.raw 0x1000
fatrm host 0 file0002.raw
fatrm host 0 file0004.raw
fatls host 0
fatwrite host 0 0x1100000 file0007.raw 0x2000
fatwrite host 0 0x1100000 file0007.raw 0x1f00
reset
EOF
./u-boot </tmp/cmds
#verify
rm -r /tmp/result /tmp/model
mkdir /tmp/result
mkdir /tmp/model
yes ABC | head -c 4096 >/tmp/model/file0001.raw
yes ABC | head -c 4096 >/tmp/model/file0003.raw
yes ABC | head -c 4096 >/tmp/model/file0005.raw
yes DEF | head -c 7936 >/tmp/model/file0007.raw
mcopy -n -i /tmp/10M.img ::file0001.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0003.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0005.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0007.raw /tmp/result
hd /tmp/10M.img
if diff -urq /tmp/model /tmp/result
then
echo Test okay
else
echo Test fail
fi
--->8-fat_test3.sh---
#!/bin/bash
make sandbox_defconfig
make
dd if=/dev/zero of=/tmp/10M.img bs=1024 count=10k
mkfs.vfat -v /tmp/10M.img
cat >/tmp/cmds <<EOF
x
host bind 0 /tmp/10M.img
fatls host 0
mw 0x1000000 0x0a434241 0x1000 # "ABC\n"
mw 0x1100000 0x0a464544 0x8000 # "DEF\n"
fatwrite host 0 0x1000000 file0001.raw 0x1000
fatwrite host 0 0x1000000 file0002.raw 0x1000
fatwrite host 0 0x1000000 file0003.raw 0x1000
fatwrite host 0 0x1000000 file0004.raw 0x1000
fatwrite host 0 0x1000000 file0005.raw 0x1000
fatrm host 0 file0002.raw
fatrm host 0 file0004.raw
fatls host 0
fatwrite host 0 0x1100000 file0007.raw 0x2000
fatwrite host 0 0x1100000 file0007.raw 0x2100
reset
EOF
./u-boot </tmp/cmds
#verify
rm -r /tmp/result /tmp/model
mkdir /tmp/result
mkdir /tmp/model
yes ABC | head -c 4096 >/tmp/model/file0001.raw
yes ABC | head -c 4096 >/tmp/model/file0003.raw
yes ABC | head -c 4096 >/tmp/model/file0005.raw
yes DEF | head -c 8448 >/tmp/model/file0007.raw
mcopy -n -i /tmp/10M.img ::file0001.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0003.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0005.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0007.raw /tmp/result
hd /tmp/10M.img
if diff -urq /tmp/model /tmp/result
then
echo Test okay
else
echo Test fail
fi
--->8-fat_test4.sh---
#!/bin/bash
make sandbox_defconfig
make
dd if=/dev/zero of=/tmp/10M.img bs=1024 count=10k
mkfs.vfat -v /tmp/10M.img
cat >/tmp/cmds <<EOF
x
host bind 0 /tmp/10M.img
fatls host 0
mw 0x1000000 0x0a434241 0x1000 # "ABC\n"
mw 0x1100000 0x0a464544 0x8000 # "DEF\n"
mw 0x1200000 0x0a494847 0x8000 # "GHI\n"
fatwrite host 0 0x1000000 file0001.raw 0x1000
fatwrite host 0 0x1000000 file0002.raw 0x1000
fatwrite host 0 0x1000000 file0003.raw 0x1000
fatwrite host 0 0x1000000 file0004.raw 0x1000
fatwrite host 0 0x1000000 file0005.raw 0x1000
fatrm host 0 file0002.raw
fatrm host 0 file0004.raw
fatls host 0
fatwrite host 0 0x1100000 file0007.raw 0x900
fatwrite host 0 0x1200000 file0007.raw 0x900 0x900
fatwrite host 0 0x1100000 file0007.raw 0x900 0x1200
fatwrite host 0 0x1200000 file0007.raw 0x900 0x1b00
reset
EOF
./u-boot </tmp/cmds
#verify
rm -r /tmp/result /tmp/model
mkdir /tmp/result
mkdir /tmp/model
yes ABC | head -c 4096 >/tmp/model/file0001.raw
yes ABC | head -c 4096 >/tmp/model/file0003.raw
yes ABC | head -c 4096 >/tmp/model/file0005.raw
yes DEF | head -c 2304 >/tmp/model/file0007.raw
yes GHI | head -c 2304 >>/tmp/model/file0007.raw
yes DEF | head -c 2304 >>/tmp/model/file0007.raw
yes GHI | head -c 2304 >>/tmp/model/file0007.raw
mcopy -n -i /tmp/10M.img ::file0001.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0003.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0005.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0007.raw /tmp/result
hd /tmp/10M.img
if diff -urq /tmp/model /tmp/result
then
echo Test okay
else
echo Test fail
fi
--->8---
Feel free to prepare a proper sandbox/py_test based tests based on
the provided test scripts.

fat: write: fix broken write to fragmented files

The code for handing file overwrite incorrectly assumed that the file on
disk is always contiguous. This resulted in corrupting disk structure
every time when write to existing fragmented file happened. Fix this
by adding proper check for cluster discontinuity and adjust chunk size
on each partial write.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch partially fixes the issue revealed by the following test
script:

--->8-fat_test1.sh---
#!/bin/bash
make sandbox_defconfig
make
dd if=/dev/zero of=/tmp/10M.img bs=1024 count=10k
mkfs.vfat -v /tmp/10M.img
cat >/tmp/cmds <<EOF
x
host bind 0 /tmp/10M.img
fatls host 0
mw 0x1000000 0x0a434241 0x1000 # "ABC\n"
mw 0x1100000 0x0a464544 0x8000 # "DEF\n"
fatwrite host 0 0x1000000 file0001.raw 0x1000
fatwrite host 0 0x1000000 file0002.raw 0x1000
fatwrite host 0 0x1000000 file0003.raw 0x1000
fatwrite host 0 0x1000000 file0004.raw 0x1000
fatwrite host 0 0x1000000 file0005.raw 0x1000
fatrm host 0 file0002.raw
fatrm host 0 file0004.raw
fatls host 0
fatwrite host 0 0x1100000 file0007.raw 0x4000
fatwrite host 0 0x1100000 file0007.raw 0x4000
reset
EOF
./u-boot </tmp/cmds
#verify
rm -r /tmp/result /tmp/model
mkdir /tmp/result
mkdir /tmp/model
yes ABC | head -c 4096 >/tmp/model/file0001.raw
yes ABC | head -c 4096 >/tmp/model/file0003.raw
yes ABC | head -c 4096 >/tmp/model/file0005.raw
yes DEF | head -c 16384 >/tmp/model/file0007.raw
mcopy -n -i /tmp/10M.img ::file0001.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0003.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0005.raw /tmp/result
mcopy -n -i /tmp/10M.img ::file0007.raw /tmp/result
hd /tmp/10M.img
if diff -urq /tmp/model /tmp/result
then
echo Test okay
else
echo Test fail
fi
--->8---

Overwritting a discontiguous test file (file0007.raw) no longer causes
corruption to file0003.raw, which's data lies between the chunks of the
test file. The amount of data written to disk is still incorrect, what
causes damage to the file (file0005.raw), which's data lies next to the
test file. This will be fixed by the next patch.

Feel free to prepare a proper sandbox/py_test based tests based on the
provided test scripts.

cmd: gpio: Correct do_gpio() return value

Use the correct return value in function do_gpio() and update
commands documentation with the return values from command_ret_t enum.

CMD_RET_SUCCESS is returned on command success and CMD_RET_FAILURE is
returned on command failure.

The command was returning the pin value, which caused confusion when
debugging (#define DEBUG).

Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Tested-by: Robert Marko <robert.marko@sartura.hr>

azure/gitlab: Update to Docker to have SDL2 available

Update to a newer Docker image that contains SDL2 libraries as required
by recent Sandbox changes.

Signed-off-by: Tom Rini <trini@konsulko.com>

azure: Use our own GRUB binaries

Use the same logic from 24df1b14f3ab to use our own GRUB binaries in
Azure pipelines as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

gitlab: use our own GRUB

Up to now we have been relying on openSUSE repositories for GRUB on arm and
arm64 though we have included GRUB in our Docker image.

Use the GRUB included in our Docker image.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

Merge tag 'efi-2020-04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi

Pull request for UEFI sub-system for efi-2020-04-rc2

Fix pylint issues in Python based tests.

Merge branch 'master' of git://git.denx.de/u-boot-socfpga

- Gen 5 and Watchdog fixes

video: enable VIDEO_ANSI and all VIDEO_BBP options

This partially reverts changes by commit 2cc393f32fd9
("video: make BPP and ANSI configs optional") since it
caused issues with other boards (missing LCD console
output on pinebook, x86 platform or sandbox). Enable
all disabled options again and opt out of not supported
color depth in board defconfigs.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Vagrant Cascadian <vagrant@debian.org>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq

- Bug fixes on ls1012a, ls1021a, ls1028ardb platforms Integrate fspi for
  ls1028a, add DM-I2C support, update secure boot header offset

Merge tag 'rpi-next-2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi

- DFU support file operations lager then the default max size
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config

test: efi_selftest: fix pylint warnings

Fix pylint warnings:

* add missing module and function documentation
* correct indentation

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

test: test_efi_fit: fix pylint warnings

Fix warnings issued by pylint:

* naming of variables
* usage of commas and semicolons
* indentation
* placement of module description

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

ddr: altera: Add DDR2 support to Gen5 driver

Add DDR2 support to Gen5 DRAM driver. As the DDR2 macro names generated
by Quartus are named differently than the DDR3 ones, use anon unions to
store them in the same structures, without growing their size.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

watchdog: designware: Optionally fetch clock and reset from DT

Add optional support for fetching watchdog clock rate from DT
and ungating reset via reset framework. This is optional as not
all platforms using DW WDT support the clock and reset frameworks
yet.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc

watchdog: designware: Convert to DM and DT probing

Convert the designware watchdog timer driver to DM and add DT probing
support. Perform minor coding style clean up, like drop superfluous
braces. These ought to be no functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc

Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86

- Various minor fixes for x86
- Switch to ACPI mode on Intel edison
- Support run-time configuration for NS16550 driver
- Update coreboot and slimbootloader serial drivers to use NS16550
run-time configuration
- ICH SPI driver fixes to hardware sequencing erase case
- Move ITSS from Apollo Lake to a more generic location
- Intel GPIO driver bug fixes
- Move to vs2017-win2016 platform build host for Azure pipelines

Merge tag 'ti-v2020.04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti

- DFU boot support for J721e
- I2C support for J721e
- GPIO support for J721e
- Android boot image updates on AM57XX
- OMAP watchdog fixes

board: ls1012ardb: do not use imply CONFIG_

Inside Kconfig we must not use the CONFIG_ prefix with the imply statement.

Fixes: 28e3c39e535b ("board: freescale: ls1012a2g5rdb: enable network
support on ls1012a2g5rdb")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

armv8: ls2088a: Updates secure boot headers offset

Updates the secure boot headers offsets of Kernel and other
firmware images for SD and NOR boot sources used by
esbc_validate command.

Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

armv8: ls1088a: Updates secure boot headers offset

Updates the secure boot headers offsets of Kernel and other
firmware images for SD and QSPI boot sources used by
esbc_validate command.

Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

armv8: lx2160a: Updates secure boot headers offset

Updates the secure boot headers offsets of Kernel and other
firmware images for SD and XSPI boot sources used by
esbc_validate command.

Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

armv8: ls1012ardb: Updates secure boot headers offset

Updates the secure boot headers offsets of Kernel and other
firmware images used by esbc_validate command.

Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

armv8: ls1046a: Updates secure boot headers offset

Updates the secure boot headers offsets of Kernel and other
firmware images for SD and QSPI boot sources used by
esbc_validate command.

Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

configs: ls1021a: Reserve low memory for CMA

The default reserved memory for CMA is high memory. If LPAE is enabled,
highmem pages are non-remapped and can not be used with
dma_alloc_coherent. This patch will reserve low memory for CMA and fix
the issue on LS1021A.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

dm: arm: ls1021a: add i2c DM support

This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

dm: arm64: ls1012a: add i2c DM support

This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

Kconfigs: layerscape: use a convenient default value for SYS_MALLOC_F_LEN

The default value of CONFIG_SYS_MALLOC_F_LEN (0x400)
leaves U-Boot with not enough memory to load i2c driver
before relocate, causing it to hang.

Change the default value of CONFIG_SYS_MALLOC_F_LEN
for below SoCs,
- LS1012A
- LS1021A
- LS1043A
- LS1046A

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

i2c: mxc_i2c: add DM_FLAG_PRE_RELOC flag

This adds DM_FLAG_PRE_RELOC flag to probe i2c driver
before relocation

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

armv8: fsl-layerscape: spl: fix build error when DM_I2C is enabled

Fix below SPL build error when DM_I2C is enabled,
- arch/arm/cpu/armv8/built-in.o: In function `board_init_f:
  arch/arm/cpu/armv8/fsl-layerscape/spl.c:74: undefined reference to `i2c_init_all'
  arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:(.text.board_init_f+0x30):
  relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol
  `i2c_init_all'
  make[2]: *** [spl/u-boot-spl] Error 1
  make[1]: *** [spl/u-boot-spl] Error 2
  make: *** [sub-make] Error 2
  arch/arm/cpu/armv8/fsl-layerscape/spl.c: In function 'board_init_f':
  arch/arm/cpu/armv8/fsl-layerscape/spl.c:74:2: warning: implicit
  declaration of function 'i2c_init_all'; did you mean 'misc_init_r'?
  [-Wimplicit-function-declaration]`

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

rtc: pcf8563: Add driver model support

Add support of driver model of pcf8563

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>

configs: ls1028a: Enable FSPI support

Enable FSPI controller support. So, flash environment can now be used

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

arm: dts: lx2160a: Add FSPI node properties

Align flexspi node properties with linux device-tree properties
Tested on LX2160A-RDB

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

arm: dts: ls1028a: Add FSPI node properties

Align flexspi node properties with linux device-tree properties
Tested on LS1028A-RDB

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

board: fsl: lx2160a: Add support to reset to eMMC

Add support of "qixis_reset emmc" command for lx2160a based platforms

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

arm: dts: ls1028a: fix interrupt properties

Sync the interrupt properties with the ones from Linux. Also use the
constants provided by the dt-bindings header. Please note, that there
are actual changes/fixes in the irq flags. U-Boot won't use the
interrupt properties anyway. It's just to be consistent with the Linux
device tree.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

arm: ls1028a: use the new flexspi driver

Also align the fspi node with the kernel one.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

configs: ls1012ardb: Enable CONFIG_SYS_RELOC_GD_ENV_ADDR

Enable the config for ls1012ardb as the entry got missed earlier.

Fixes: 8d8ee47e03 ("env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol")
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

azure: Move to vs2017-win2016 platform build host

Azure is moving to remove the vs2015-win2012r2 platform build host.  The
two suggested new platforms to use are vs2017-win2016 and windows-2019.
For now, move up to vs2017-win2016.

Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>

gpio: intel_gpio: Fix register/bit offsets intel_gpio_get_value()

Fix the following in intel_gpio_get_value():

 * The value of the register is contained in the variable 'reg', not in
   'mode'. The variable 'mode' contains only the configuration whether
   the gpio is currently an input or an output.

 * The correct bitmasks for the input and output value are
   PAD_CFG0_RX_STATE and PAD_CFG0_TX_STATE.
   Use them instead of the currently used PAD_CFG0_RX_STATE_BIT and
   PAD_CFG0_TX_STATE_BIT.

Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

gpio: intel_gpio: Clear tx state bit when setting output

Add missing 'PAD_CFG0_TX_STATE' to the clear mask for pcr_clrsetbits32().
Otherwise this bit cannot be cleared again after it has been set once.

Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

gpio: intel_gpio: Pass pinctrl device to pcr_clrsetbits32()

The function pcr_clrsetbits32() expects a device with a P2SB parent
device. In intel_gpio_direction_output() and intel_gpio_set_value()
the device 'dev' is passed to pcr_clrsetbits32(), which is a
gpio-controller with a device 'pinctrl' as parent. This does not match
the expectations of pcr_clrsetbits32(). But the 'pinctrl' device has a
P2SB as parent.

Pass the 'pinctrl' device instead of the 'dev' device to
pcr_clrsetbits32().

Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

x86: itss: Remove apl-prefix

The Interrupt Timer Subsystem (ITSS) is not specific to Apollo Lake, so
remove the apl-prefix of the implemented functions/structures/...

Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

x86: itss: Add a Kconfig option to enable/disable ITSS driver

Add a Kconfig option to support enabling/disabling the inclusion of
the ITSS driver depending on the platform.

Atuomatically select the ITSS driver when building for Apollo Lake.

Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: squashed in http://patchwork.ozlabs.org/patch/1232761/]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>

x86: Move itss.c from Apollo Lake to a more generic location

The Interrupt Timer Subsystem (ITSS) is not specific to Apollo Lake, so
move it to a common location within arch/x86.

Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: conditionally build itss.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>

watchdog: omap_wdt: Fix WDT coding style

Fix obvious coding style problems, no functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

watchdog: omap_wdt: Fix WDT reloading

The watchdog timer value was never updated in the hardware by this
driver, so the watchdog triggered on some random stale value that
was left in the hardware. The TI SPRUH37C says, quote:

  20.4.3.9 Modifying Timer Count/Load Values and Prescaler Setting
  ...
  After a write access, the load register value and prescaler ratio
  registers are updated immediately, but new values are considered
  only after the next consecutive counter overflow or after a new
  trigger command (the WDT_WTGR register).

This means at least one trigger must happen. The driver probably
depended on someone calling it's .reset() callback, however that
is not guaranteed e.g. if the WDT operates without servicing.

Add this missing trigger.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

watchdog: omap_wdt: Fix WDT timeout configuration

The timeout parameter of omap3_wdt_start() is in miliseconds, while
GET_WLDR_VAL() expects parameter in seconds. Fix this so the WDT
driver is actually usable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

configs: j721e_evm_a72: Add GPIO support

Enable CONFIG_DA8XX_GPIO to enable GPIO support.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: dts: k3-j721e-main: Add Support for gpio0

Add the main_gpio0 node.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

gpio: da8xx_gpio: Add "ti,keystone-gpio" compatible

Add "ti,keystone-gpio" compatible so as be able to use Linux DT files as
is.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

gpio: da8xx_gpio: Fix compiler warning

Fix below compiler warning for 64bit builds

drivers/gpio/da8xx_gpio.c: In function ‘davinci_get_gpio_bank’:
drivers/gpio/da8xx_gpio.c:446:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  return (struct davinci_gpio *)addr;

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

configs: j721e_evm_defconfig: Enable PCA953x IO expander

Enable PCA953x IO expander to control MMC/SD power lines.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: dts: k3-j721e-common-proc-board: Enable I2C expander for SPL

IO expanders are required to power cycle SD card. So enable the same

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: dts: k3-j721e-common-proc-board: Add I2C GPIO expander

Add I2C GPIO expander required to power cycle MMC/SD

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: dts: k3-j721e: Add I2C nodes

J721e SoC has 2 I2C instances in MCU domain and 7 I2C instances in main
domain. Add DT nodes for the same

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

gpio: pca953x_gpio: Add support for 24 bit IO expander

J721e EVM has a TCA6424 IO expander that has 24 GPIOs. Add support for
the same

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

configs: j721e_evm_r5/a72_defconfig: Enable DFU related configs

Enable DFU, Fastboot and USB mass storage gadget related configs

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

configs: j721e_evm_r5/a72_defconfig: Enable USB Gadget related configs

Enable USB Gadget for R5 SPL, A72 SPL and A72 U-Boot to support DFU boot

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

configs: j721e_evm_r5_defconfig: Increase early malloc size

Increase R5 SPL early malloc memory pool by ~7K to accommodate SPL USB
DFU boot requirements

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

configs: j721e_evm: Add DFU related variables

Add configs to download varies stages of bootloader images to RAM during
DFU boot.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: dts: k3-j721e-common-proc-board: Enable USB0 in peripheral mode

Enable USB0 in peripheral mode so that it be used for DFU

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: mach-k3: sysfw-loader: Add support to download SYSFW via DFU

Add support to download SYSFW into internal RAM via DFU in DFU boot
mode. Prepare a DFU config entity entry dynamically using buffer address
allocated for SYSFW and start DFU gadget to get SYSFW.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: mach-k3: j721e: Rename BOOT_DEVICE_USB to BOOT_DEVICE_DFU

J721e does not support USB Host MSC boot, but only supports DFU boot.
Since BOOT_DEVICE_USB is often used for host boot mode and
BOOT_DEVICE_DFU is used for DFU boot, rename BOOT_DEVICE_USB macro to
BOOT_DEVICE_DFU

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

configs: j721e_evm_a72: Fix redundant environment offset

The current environment offset overlaps with the sysfw area and whenever
environment is saved in the redundant slot, it overwrites sysfw.itb. Fix
the offset to prevent this.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: ti: boot: Use correct dtb and dtbo on Android boot

Read correct dtb blob from boot.img/recovery.img and apply correct dtbo
blobs from dtbo partition.

Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

env: ti: boot: Boot Android with dynamic partitions

Changes:
  - use boot.img instead of boot_fit.img
  - use .dtb from boot.img v2
  - implement recovery boot
  - always boot ramdisk from boot.img, we can't mount system as root
    now, as system is a logical partition inside of super partition
  - don't add "skip_initramfs" to cmdline anymore
  - to boot into recovery, use boot image from recovery partition
  - prepare partition table:
    - A/B scheme
    - use 'super' partition instead of 'system' and 'vendor'
    - add dtbo partitions
    - introduce metadata partition

Not implemented: reading and applying dtbo blobs from dtbo partition.

Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>