Currently the SPL binary is 67 kB, which leaves only 1 kB of free
internal RAM space.
The following options can be safely removed to save some precious
SPL space:
- CONFIG_SPL_FS_EXT4: u-boot-dtb.img is stored in raw sector via dd
command (at offset 69 kB)
- CONFIG_SPL_I2C_SUPPORT: I2C is not used during SPL
- CONFIG_SPL_OS_BOOT: no need to make Falcon mode supported
by default
After this change the SPL binary size gets down to 51 kB.
Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Mon, 22 Jul 2019 01:25:10 +0000 (01:25 +0000)]
i.MX7ULP: Change clock rate calculation for NIC1 BUS and EXT
On i.MX7ULP B0, there is change in NIC clock dividers architecture.
On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but
on B0 they are parallel with NIC1 DIV. So now the dividers are independent.
This patch modifies the scg_nic_get_rate function according to this change.
Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Mon, 22 Jul 2019 01:25:03 +0000 (01:25 +0000)]
i.MX7ULP: Workaround APLL PFD2 to 345.6Mhz
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider
set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU
is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28)
to workaround the problem. The correct fix should let GPU handle the
clock rate in kernel.
Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Bai Ping [Mon, 22 Jul 2019 01:24:42 +0000 (01:24 +0000)]
i.MX7ULP: Fix system reset after a7 rtc alarm expired.
The board will reboot if A7 core enter mem mode by rtc, then M4 core
enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode
to fix this issue.
Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access
it. So check the CPU rev and not apply the settings for B0.
Signed-off-by: Bai Ping <ping.bai@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 22 Jul 2019 01:24:39 +0000 (01:24 +0000)]
i.MX7ULP: evk: Modify FDT file to disable SD3.0 for usb boot
Since the SD3.0 kernel driver needs M4 image support, this causes
problem for usb boot booting into kernel. To decouple the relationship,
we modify the FDT file in u-boot to disable SD3.0.
So the kernel won't depend on M4 image.
Robert Hancock [Thu, 8 Aug 2019 18:14:39 +0000 (12:14 -0600)]
ARM: imx: Support larger SPL size on IMX6DQ
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca> Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
spl: imx: only use HAB if spl fit signature is not enabled
There is no need to use HAB for FIT signature validation when
SPL_FIT_SIGNATURE is also enabled, as that will be validated via the
normal U-Boot signed FIT image flow.
This allows having SPL validated by HAB and the payloads to follow
being validated with FIT signatures only.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q
variants, which are quite similar and already managed via only one
dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in
order to automatically enable the HAS_CAAM and MX6_SMP features.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Commit e37ac717d796 ("Convert to use fsl_esdhc_imx for i.MX platforms")
converted FSL_ESDHC to FSL_ESDHC_IMX, but the config check for
apalis_imx6 wasn't updated accordantly.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Peng Fan [Wed, 7 Aug 2019 06:40:53 +0000 (06:40 +0000)]
spl: pass args to board_return_to_bootrom
Pass spl_image and bootdev to board_return_bootrom.
i.MX8MN needs the args to let ROM to load images
Cc: Simon Glass <sjg@chromium.org> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Cc: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Peng Fan [Tue, 6 Aug 2019 10:05:48 +0000 (10:05 +0000)]
pinctrl: imx: use devfdt_get_addr_size_index
fdtdec_get_addr_size could not parse addr/size correctly is
using address-cells 2 and size-cells 2 on an ARM32 SoC.
So switch to use devfdt_get_addr_size_index.
Peng Fan [Thu, 1 Aug 2019 06:02:41 +0000 (06:02 +0000)]
imx: mx6ul_14x14_evk: Fix SPL boot
When booting SPL on the board, met boot failure:
"
Trying to boot from MMC2
MMC Device 1 not found
spl: could not find mmc device 1. error: -19
SPL: failed to boot from all boot devices
"
Let's register the two mmc controllers in SPL stage to
avoid boot failure.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Thu, 8 Aug 2019 09:55:47 +0000 (09:55 +0000)]
arm: dts: import dts for i.MX6ULZ
Import kernel dts for i.MX6ULZ from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Thu, 8 Aug 2019 09:55:37 +0000 (09:55 +0000)]
arm: dts: sync dts for i.MX6ULL
Sync kernel dts for i.MX6ULL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Thu, 8 Aug 2019 09:55:33 +0000 (09:55 +0000)]
arm: dts: sync dts for i.MX6UL
Sync kernel dts for i.MX6UL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Eugeniy Paltsev [Mon, 7 Oct 2019 16:10:50 +0000 (19:10 +0300)]
NET: DW: fix regression for ARC boards
The commit 642b80d256e ("net: designware: drop compatible altr, socfpga-stmmac")
breaks designware ethernet for all ARC boards. It removes
"altr, socfpga-stmmac" compatible from "drivers/net/designware.c"
without changing compatible in the boards which use it.
Fix that by adding "snps,arc-dwmac-3.70a" compatible string to
"drivers/net/designware.c" and using it in ARC boards device tree.
AKASHI Takahiro [Thu, 22 Aug 2019 07:47:39 +0000 (16:47 +0900)]
cmd: host: fix seg fault at "host info"
With the patch below applied, host_block_dev structure was switched
to be placed in platdata rather than priv. The command "host info"
must be aligned with this change. Otherwise, we will see "Segmentation
Fault."
Fixes: 8f994c860d91 ("sandbox: blk: Switch to use platdata_auto_alloc_size for the driver data") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Fri, 4 Oct 2019 16:22:43 +0000 (12:22 -0400)]
Merge branch '2019-10-04-master-imports'
- Assorted TI platform fixes
- Revert the change that broke environment flag validation
- Assorted typo fixes
- Assorted Kconfig dependency fixes
- Other minor bug fixes
Adam Ford [Wed, 7 Aug 2019 15:16:33 +0000 (10:16 -0500)]
ARM: dts: imx6q-logicpd: Add missing imx6q-logicpd-u-boot for SPL
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and
usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file
which will enable these functions so SPL can properly setup UART, detect
microSD card, and startup.
Fixes: 8f4691e31a18 ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled,
remove MMC init")
At this point we are using part number sub-command to retrieve UUID
of the partition using it's name.
e.g.:
part number mmc $mmcdev system_a system_a_index
part uuid mmc $mmcdev:${system_a_index} system_a_uuid
Since 'part uuid' sub-command expects partition index in hex format and
'part number' returns decimal value, 'part uuid' command will provide
wrong UUID or fail.
The memory allocated to store the FIT image containing SYSFW and board
configuration data is statically defined to the largest size expected.
This was 269000 bytes but now needs to be grown to 276000 to make room
for the signatures attached to the board configuration data on High
Security devices.
Simon Glass [Wed, 25 Sep 2019 14:55:50 +0000 (08:55 -0600)]
dm: core: Correct bad cast in ofnode_get_addr_size_index()
At present this code passes an fdt_addr_t pointer as a u64 pointer which
is not safe, since sizeof(fdt_addr_t) may be 4, e.g. with sandbox. Correct
this to avoid a stack corruption problem.
Fixes: e679d03b08 (core: ofnode: Add ofnode_get_addr_size_index) Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 25 Sep 2019 14:55:46 +0000 (08:55 -0600)]
dm: core: Correct low cell in ofnode_read_pci_addr()
This reads the low cell of the PCI address from the wrong cell. Fix it.
Also fix the function that this code came from.
Fixes: 9e51204527 (dm: core: Add operations on device tree references) Fixes: 4ea5243a3a (fdt: fix fdtdec_get_pci_addr() for CONFIG_PHYS_64BIT) Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When booting through the efi stub, the memory map get's created by
reading the dram bank information. Depending on the version of the RPi4
this information changes. Read the device tree to initialize the dram
bank data structure. This way the kernel is able to access the whole
range of available memory.
Tom Rini [Mon, 30 Sep 2019 11:21:38 +0000 (07:21 -0400)]
Merge tag 'u-boot-atmel-fixes-2019.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2019.10 cycle:
This includes only tiny cleanups on env changes related to 2019.10 new
features: removal of duplicate env settings (otherwise there may be
warnings in building..) and a small fix for flashes on Gardena smart
gateway (requires nand bad block tables).
at91: configs: Drop duplication of defconfig macros
'commit a9221f3ebd6d ("at91, omap2plus: configs: migrate CONFIG_ENV_ to defconfigs")'
migrated CONFIG_ENV_ macros to defconfigs but did not remove the
identical redefinition of these macros in include/configs/.
Since the duplicated macros have the same value as the ones in defconfigs,
no "redefined" warnings were raised. Remove duplicated macros for all
sama5 and sam9x5ek boards.
While verifying that the removal of the macros from include/configs did
not change the same macros in defconfigs, overwrite the old defconfig by
saving them with the output from "make arch=ARM savedefconfig". This
resulted in the movement of some macros in the defconfig files.
This patch enables the BBT in NAND on the AT91SAM based GARDENA smart
Gateway. This is especially important, since the Linux driver also
enables this option and uses the BBT table pages. Without setting this
option, U-Boot will try to re-use these pages again (e.g. UBI).
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Mon, 18 Mar 2019 02:20:31 +0000 (03:20 +0100)]
ARM: dts: rmobile: Restore increase off-on delay on the SD Vcc regulator
This patch restores commit c49d0ac38a76 ("ARM: dts: rmobile: Increase off-on
delay on the SD Vcc regulator"), which was accidentally dropped during DT
resync in commit 317d13ac6307 ("ARM: dts: rmobile: Synchronize Gen3 DTs with
Linux 5.0").
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Fixes: 317d13ac6307 ("ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.0")
rockchip: make_fit_atf.py: fix .its generation for a single atf image
The commit 619f002db864 ("rockchip: make_fit_atf.py: fix loadables property
set error") fixed the double-loading of the primary atf-image, but didn't
take into account that there may be rare atf images with only that main
section present.
Right now this will result in a broken its due to the loadables section not
getting closed correctly, so fix that by adapting the guards around the loop.
The guards now protect against 0 segments when the bl31 binary doesn't
contain any section and 1 segment when only a core atf section is present.
rockchip: misc: read the correct number of bytes from the efuse
Originally the cpuid var the value gets read into was defined as
u8 cpuid[RK3399_CPUID_LEN];
hence the sizeof(cpuid) would return the correct the correct number
of array elements.
With the move to a separate function cpuid becomes a pointer and
sizeof(cpuid) hence returns the pointer size - 8 in the arm64 case.
We do have the actual id length available as function param so use
it for actual amount of bytes to read.
Fixes: 04825384999f ("rockchip: rk3399: derive ethaddr from cpuid") Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Since commit af95f20 ("env: Create a new file for environment functions"),
a new header file exists.
So, this commit add a missing header file.
Fixes:
include/env.h:158:1: error: unknown type name ‘ulong’; did you mean ‘long’?
ulong env_get_ulong(const char *name, int base, ulong default_val);
^~~~~
long
include/env.h:158:49: error: unknown type name ‘ulong’; did you mean ‘long’?
ulong env_get_ulong(const char *name, int base, ulong default_val);
Since commit d3716dd ("env: Rename the redundancy flags"), the
definitions of ENV_REDUND_OBSOLETE & ENV_REDUND_ACTIVE was moved
to env.h.
Fixes:
tools/env/fw_env.c:122:22: error: ‘ENV_REDUND_ACTIVE’ redeclared as different kind of symbol
static unsigned char ENV_REDUND_ACTIVE = 1;
^~~~~~~~~~~~~~~~~
In file included from tools/env/fw_env.c:13:
include/env.h:63:2: note: previous definition of ‘ENV_REDUND_ACTIVE’ was here
ENV_REDUND_ACTIVE = 1,
^~~~~~~~~~~~~~~~~
tools/env/fw_env.c:127:22: error: ‘ENV_REDUND_OBSOLETE’ redeclared as different kind of symbol
static unsigned char ENV_REDUND_OBSOLETE;
^~~~~~~~~~~~~~~~~~~
In file included from tools/env/fw_env.c:13:
include/env.h:62:2: note: previous definition of ‘ENV_REDUND_OBSOLETE’ was here
ENV_REDUND_OBSOLETE = 0,
Mark Kettenis [Fri, 9 Aug 2019 20:30:26 +0000 (22:30 +0200)]
sunxi: video: HDMI: Fix LCD clock divider
Currently we may end up with an LCD clock divider that differs from
the HDMI PHY clock divider if we can't exactly match the pixel clock.
Fix this by using DIV_ROUND_UP to calculate the divider. This works
since the PLL is chosen such that the resulting pixel clock is
never higher than the requested pixel clock.
After mxc_ipuv3 DM_VIDEO conversion showing splash image
doesn't work. Fix this. Also enable white on black console
configuration as it used to be with cfb_console driver.
After mxc_ipuv3 DM_VIDEO conversion showing splash image
doesn't work. Fix this. Also enable white on black console
configuration as it used to be with cfb_console driver.
splash: fix logo drawing if CONFIG_VIDEO_LOGO enabled
After mxc_ipuv3 DM_VIDEO conversion board configs with enabled
CONFIG_VIDEO_LOGO do not show splash screen (previosly drawing
splash screen worked via cfb_console driver with CONFIG_VIDEO_LOGO
enabled). Use splash_source library for loading splash images
when CONFIG_SPLASH_SOURCE is selected, otherwise prepare built-in
video logo for drawing.
u16 version of strcmp(): u16_strncmp() works like u16_strcmp() but only
at most n characters (in u16) are compared.
This function will be used in my UEFI secure boot patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Now that APPEND_WRITE is supported,
the result check for the only existing test case should be changed to
'todo' to 'error', while two more test cases are added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If EFI_VARIABLE_APPEND_WRITE is specified in attributes at
efi_set_variable(), specified data will be appended to the variable's
original value. Attributes other than APPEND_WRITE should not be
modified.
With this patch, APPEND_WRITE test in 'variables' selftest will pass.
projects / u-boot.git / log
