Some ARMv7 boards using PSCI require to be in secure-mode when booted via
'bootz' or 'bootm'. During distro-boot 'bootefi bootmgr' is called to check
if booting via UEFI is possible.
With the change we change the switch from secure mode to non-secure mode is
moved from the UEFI subsystem setup to just before calling StartImage().
Cc: Jernej Škrabec <jernej.skrabec@gmail.com>
Reported by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_selftest: test EFI_BLOCK_IO_PROTOCOL.Media->LastBlock
The field Media->LastBlock of the EFI_BLOCK_IO_PROTOCOL must be filled
with the index of the last logical block (LBA) for the block device that
our test driver provides.
After calling ConnectController() U-Boot exposes the block IO protocol for
the partition check that the value of Media->LastBlock equals the partition
size minus one.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Excluding ut str in test/cmd_ut.c but compiling test/str_ut.c results in
failure of the Python test invoking the C unit tests as observed on
sipeed_riscv_smode_defconfig:
Excluding ut bootm in test/cmd_ut.c but compiling test/bootm.c results in
failure of the Python test invoking the C unit tests as observed on
sipeed_riscv_smode_defconfig:
Fixes: f158ba15ee0f ("bootm: Add tests for fixup_silent_linux()") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 28 Jan 2021 19:39:56 +0000 (14:39 -0500)]
test: Update test_fs to not use deprecated pytest.yield_fixture()
As noted in comments, yield_fixture has been deprecated for longer than
our minimum required version of pytest. Newer versions of pytest cause
this to be a louder warning, and as the migration is trivial, perform it
now.
sandbox: Traceback (most recent call last):
File "./test/py/test.py", line 20, in <module>
sys.exit(load_entry_point('pytest', 'console_scripts', 'pytest')(args))
TypeError: console_main() takes 0 positional arguments but 1 was given
The definition of console_scripts has changed as follows:
The new function console_main() has a comment:
"This function is not meant for programmable use; use `main()`"
Hence let's call pytest.main() directly.
Move args processing into the __main__ paragraph.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com> Tested-by: Tom Rini <trini@konsulko.com>
Compiling wandboard_defconfig with CONFIG_UT_LOG=y leads to a build error:
test/log/pr_cont_test.c: In function ‘log_test_pr_cont’:
test/log/pr_cont_test.c:28:14: error:
‘gd_t’ {aka ‘volatile struct global_data’} has no member named ‘log_fmt’
log_fmt = gd->log_fmt;
We do not want to let CONFIG_UT_LOG depend on CONFIG_LOG=y because we have
tests for logging functions called with CONFIG_LOG=n.
Fix the build dependency.
Reported-by: Kever Yang <kever.yang@rock-chips.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Matthias Brugger [Wed, 27 Jan 2021 09:42:30 +0000 (10:42 +0100)]
fs: btrfs: Select SHA256 in Kconfig
Since commit 565a4147d17a ("fs: btrfs: Add more checksum algorithms")
btrfs uses the sha256 checksum algorithm. But Kconfig lacks to select
it. This leads to compilation errors:
fs/built-in.o: In function `hash_sha256':
fs/btrfs/crypto/hash.c:25: undefined reference to `sha256_starts'
fs/btrfs/crypto/hash.c:26: undefined reference to `sha256_update'
fs/btrfs/crypto/hash.c:27: undefined reference to `sha256_finish'
SkyLake.Huang [Wed, 20 Jan 2021 07:31:33 +0000 (15:31 +0800)]
spi: mtk_snor: add support for MTK SPI NOR controller
This patch adds support for MTK SPI NOR controller, which you
can see on mt7622 & mt7629.
1. This controller is designed only for SPI NOR. We can't adjust
its bus clock dynamically. Set clock in dts instead.
2. This controller only supports 1-1-1 write mode.
3. Remove mtk_snor_match_read() since upper SPI-MEM layer already
handles command.
4. sf read/write/update commands are tested with this driver.
rtc: add rtc-abx80x, a driver for the Abracon AB x80x i2c rtc
This is a basic driver for the ultra-low-power Abracon AB x80x series
of RTC chips. It supports in particular, the supersets AB0805 and AB1805.
It allows reading and writing the time, and enables the supercapacitor or
battery charger.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
autoboot: fix illegal memory access when stop key and delay key are empty
If both stop key and delay key are empty, the length of these
keys is 0. The subtraction operation will cause the u_int type
variable to overflow, will cause illegal memory access in key
input loop.
This commit fixes this bug by using int type instead of u_init. Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Thu, 14 Jan 2021 03:29:57 +0000 (20:29 -0700)]
binman: Allow reading entries from a subnode
Some images may have multiple copies of the same thing, e.g. two versions
of the read/write U-Boots. It is necessary to read data from one or other
of these under selection of the verified-boot logic. Add a function to
select the subnode to use.
Simon Glass [Thu, 14 Jan 2021 03:29:55 +0000 (20:29 -0700)]
crc32: Exclude crc32 from TPL
Unfortunately the toolchain often brings in the crc32 table even if the
function is not actually used. For now, exclude it from the TPL build,
which is very sensitive to size.
Simon Glass [Thu, 14 Jan 2021 03:29:54 +0000 (20:29 -0700)]
mmc: pci_mmc: Set the removable flag
Set this flag so that it is available to those looking at the device. For
non-removable devices there is no need to check for insertion/removable
since the media can never change.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Simon Glass [Thu, 14 Jan 2021 03:29:52 +0000 (20:29 -0700)]
mmc: pci_mmc: Only generate ACPI code for the SD card
At present if an eMMC part is in the system, the ACPI table generated
will include information about that, as well as the SD card. We only need
to include the SD card, since it has a card-detect GPIO. Use a different
compatible string for each option, and add code only for the SD card.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Simon Glass [Thu, 14 Jan 2021 03:29:51 +0000 (20:29 -0700)]
uuid: Add a comment for UUID_STR_LEN
This macro is the length of the string but excludes the terminator. Users
must add 1 when declaring a large-enough string. Add a comment to make
this clear.
Simon Glass [Thu, 14 Jan 2021 03:29:46 +0000 (20:29 -0700)]
video: Allow syncing the entire framebuffer to the copy
In some cases so much of the framebuffer is updated that it is not worth
copying the changes piece by piece to the copy framebuffer. Add a function
to copy the whole thing.
Simon Glass [Thu, 14 Jan 2021 03:29:42 +0000 (20:29 -0700)]
spl: Add functions for next and previous phase
It is useful to be able to figure out which phase we are loading next and
which phase we came from. Add some functions to handle this as well as
returning the name of a phase. This allows messages like "Booting to x"
where x is the next phase.
At present, TPL says 'Jumping to U-Boot' at the end, when in fact it is
jumping to SPL. This is confusing, so use the new functions to correct
this.
Tests for this will come with an upcoming minor SPL test refactor.
Philippe Reynes [Tue, 12 Jan 2021 18:18:54 +0000 (19:18 +0100)]
lib: rsa: rsa-verify: don't look for keys in the FIT image
In the function rsa_verify_hash, if the "main" key doesn't
work, u-boot try others keys. But it searches those keys
in the FIT image instead of the u-boot device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Tue, 12 Jan 2021 11:03:43 +0000 (12:03 +0100)]
pci: Remove CONFIG_PCI_ENUM_ONLY as it's not used (any more)
This patch completely removes CONFIG_PCI_ENUM_ONLY from the PCI code as
it is not configured for any board (any more). With this removal, some
PCI related files get cleaned up a bit.
Additional, dm_pciauto_setup_device() is now static, as it's not
referenced from any code outside of this C file.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
common: fit-sig: Fix error message in fit_config_verify_sig()
In fit_config_verify_sig(), when no 'signature*' subnode exists in
the configuration node, the fdt_for_each_subnode() loop is a no-op.
Therefore, no error flags are set, and 'err_,sg' is not populated
with an error string. This is incorrect behavior.
Populate err_msg to indicate that no 'signature' is found, before
entering the loop. The first call to fit_image_verify_sig() will
override clear err_msg, or set it to a more specific message.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Pali Rohár [Wed, 4 Nov 2020 14:33:44 +0000 (15:33 +0100)]
Makefile: Do not call useless command 'true'
Macro 'cmd_objcopy_uboot' currently does not work with passed empty command
expanded from 'cmd_static_rela' and therefore dummy command 'true' is set
in 'cmd_static_rela' to workaround this issue.
Eliminate it now by fixing 'cmd_objcopy_uboot' macro to work also with
empty 'cmd_static_rela' macro and remove useless invocation of command
'true'.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
- Espressobin: Disable slot when emmc is not present (Pali)
- DS414; config header cleanup (Phil)
- PCI: auto-config enhancement (Phil)
- pci_mvebu: Also map IO region (Phil)
- serial: a3720: Implement pending method for output direction (Pali)
- turris_mox: Enable a few commands (Marek)
- helios4 & ClearFog changes (Dennis)
- Plus some minor misc changes
Neil Armstrong [Wed, 20 Jan 2021 08:54:53 +0000 (09:54 +0100)]
cmd: pxe: add support for FDT overlays
This adds support for specifying FDT overlays in an extlinux/pxelinux
configuration file.
Without this, there is no simple way to apply overlays when the kernel
and fdt is loaded by the pxe command.
This change adds the 'fdtoverlays' keyword for a label, supporting multiple
overlay files to be applied on top of the fdt specified in the 'fdt' or
'devicetree' keyword.
Marek Vasut [Sat, 16 Jan 2021 23:16:16 +0000 (00:16 +0100)]
net: phy: micrel: Try default PHY ofnode first
The phydev structure has a PHY OF node pointer in it, use that OF node
first when looking up PHY OF node properties, since that is likely the
correct PHY OF node pointer. If the pointer is not valid, which is the
case e.g. on legacy DTs, fall back to parsing MAC ethernet-phy subnode.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Ramon Fried <rfried.dev@gmail.com>
Abbie Chang [Thu, 14 Jan 2021 21:34:12 +0000 (13:34 -0800)]
net: phy: ca_phy: Add driver for CAxxxx SoCs
Add phy driver support for MACs embedded inside Cortina Access SoCs
Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com> Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Tom Rini <trini@konsulko.com> CC: Aaron Tseng <aaron.tseng@cortina-access.com>
Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver
Stefan Roese [Mon, 16 Nov 2020 17:02:30 +0000 (18:02 +0100)]
net: e1000: Add missing address translations
Add some missing address translations from virtual address in local DRAM
to physical address, which is needed for the DMA transactions to work
correctly.
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com>
Stefan Roese [Mon, 16 Nov 2020 17:02:29 +0000 (18:02 +0100)]
net: e1000: Use virt_to_phys() instead of pci_virt_to_mem()
Using (dm_)pci_virt_to_mem() is incorrect to translate the virtual
address in local DRAM to a physical address. The correct macro here
is virt_to_phys() so switch to using this macro.
As virt_to_bus() is now not used any more, this patch also removes
both definitions (DM and non-DM).
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com>
Marek Behún [Tue, 19 Jan 2021 14:49:26 +0000 (15:49 +0100)]
arm: mvebu: turris_mox: enable setexpr command in defconfig
Enable setexpr command in defconfig for Turris MOX. We have found that
this is sometimes useful in U-Boot scripts and there is enough space in
NOR memory on MOX.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Thu, 14 Jan 2021 14:46:35 +0000 (15:46 +0100)]
serial: a3720: Implement pending method for output direction
To check if some output characters are waiting either in Transmitter
Holding Register or Transmitter Shift Register we need to look at
TX_EMPTY bit of UART Status Register.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Phil Sutter [Sun, 3 Jan 2021 22:06:46 +0000 (23:06 +0100)]
pci: pci_mvebu: Define an IO region as well
Configure an IO region and window for PNP identical to how MEM region is
set up. Linux does this only if the DT defines a pcie-io-aperture
property for the SOC, but since all supported boards do this should not
be needed.
Signed-off-by: Phil Sutter <phil@nwl.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Phil Sutter [Sun, 3 Jan 2021 22:06:45 +0000 (23:06 +0100)]
pci: Make auto-config code a little more robust
On my DS414, some PCI devices return odd values when probing BAR sizes.
An obvious case is all-ones response, the Linux driver
(drivers/pci/probe.c) catches those explicitly and a comment explains
that either bit 0 or bit 1 must be clear (depending on MEM or IO type).
Other BARs return e.g. 0xfff0000f or 0xfff00004 and thus manage to break
size calculation due to the "middle" zeroes. Mitigate that copying more
or less what Linux does and do a "find least bit set".
Signed-off-by: Phil Sutter <phil@nwl.cc> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Pali Rohár [Mon, 21 Dec 2020 10:09:10 +0000 (11:09 +0100)]
arm: mvebu: Espressobin: Disable slot when emmc is not present
This change extends previous commit 061c6d1b238a ("arm: mvebu: Espressobin:
Detect presence of emmc at runtime") and when emmc is not present then emmc
is removed from U-Boot DM and corresponding slot is disabled. Therefore on
Espressobin board without soldered emmc, state of emmc hw should be same as
if emmc was disabled in DTS.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Harm Berntsen [Sun, 29 Nov 2020 10:08:02 +0000 (10:08 +0000)]
gpio: Add support for DM GPIO for Kirkwood
The Armada driver also works on Nedap's custom Kirkwood board with a
Marvell 88F6180 CPU. The original commit of that driver,
commit 704d9a645e17 ("gpio: Add DM GPIO driver for Marvell MVEBU"),
also mentions that this driver would be suitable for Kirkwood. This
does not completely replace the Kirkwood specific driver as there
are still boards depending on that driver.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com> CC: Stefan Roese <sr@denx.de>, Reviewed-by: Stefan Roese <sr@denx.de>
Dennis Gilmore [Fri, 11 Sep 2020 16:56:59 +0000 (11:56 -0500)]
ARM: Distro boot: document the need for fdtfile variable to be set
When testing builds provided in https://github.com/openwrt/openwrt/pull/3360
I discovered that fdtfile was not set and as a result the firmware was not
functional. So I am documenting what is needed.
Jernej Skrabec [Mon, 11 Jan 2021 20:11:53 +0000 (21:11 +0100)]
sunxi: Add support for OrangePi Zero2
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.
The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.
Jernej Skrabec [Mon, 11 Jan 2021 20:11:46 +0000 (21:11 +0100)]
sunxi: Add support for H616 SoC
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 11 Jan 2021 20:11:44 +0000 (21:11 +0100)]
mmc: sunxi: Refactor mod clock register offset
So far the only difference between the various Allwinner MMC controller
we are concerned about is the mod clock register offset.
This is actually not directly related to the MMC controller IP, but an
integration choice, dependent on the SoC this appears in.
To avoid becoming trapped with some compatible fallback strings, let's
remove the whole struct sunxi_mmc_variant, and replace this with a SoC
based choice, which we can derive from the CONFIG_MACH_SUNx_y symbols.
This will later simplify H616 support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:43 +0000 (21:11 +0100)]
sunxi: Add H616 DRAM support
Allwinner H616 supports many types of DRAM. Most notably it supports
LPDDR4. However, all commercially available boards at this time use
only DDR3, so this commit adds only DDR3 support.
Controller and MBUS are very similar to H6 but PHY is completely
unknown.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:42 +0000 (21:11 +0100)]
sunxi: add support for R_I2C on H616
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:41 +0000 (21:11 +0100)]
sunxi: add support for H616 uart0
This port is used for debug terminal on all known H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:40 +0000 (21:11 +0100)]
sunxi: introduce support for H616 clocks
H616 has mostly the same clocks as H6 with some small differences. Just
reuse H6 clocks for H616 and handle differences with macros.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 11 Jan 2021 20:11:39 +0000 (21:11 +0100)]
sunxi: support loading with SPL > 32KB
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.
spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.
In the process of function rework, also add missing function argument.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Samuel Holland <samuel@sholland.org>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:38 +0000 (21:11 +0100)]
sunxi: Add support for I2C on H6 like SoCs
I2C support, especially R_I2C port, will be needed in future. Upcoming
support for H616 will need R_I2C to adjust DRAM voltage.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:37 +0000 (21:11 +0100)]
sunxi: prcm: Add memory map for H6 like SoCs
There was no need to have prcm definitions for H6 and similar SoCs till
now. However, support R_I2C will be needed soon in SPL.
Move old definitions to prcm_sun6i.h and add new ones in prcm_sun50i.h.
One of those files will be selected in common prcm.h based on defined
macros.
This commit doesn't do any functional change.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:36 +0000 (21:11 +0100)]
i2c: mvtwsi: sunxi: update macro
While currently none of the newer Allwinner SoCs currently has I2C
support implemented in U-Boot, this will change soon. mvtwsi driver is
good as it is for them except one macro. Update it to be ready once I2C
support lands for those SoCs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Mon, 11 Jan 2021 20:11:34 +0000 (21:11 +0100)]
sunxi: Introduce common symbol for H6 like SoCs
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Mon, 18 Jan 2021 23:23:59 +0000 (23:23 +0000)]
sunxi: Properly check for SATAPWR and MACPWR
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as
string Kconfig symbols are always "defined" from the preprocessor's
perspective. This lead to unnecessary calls to the GPIO routines, but
also always added a half a second delay to wait for a SATA disk to power
up. Many thanks to Peter for pointing this out!
Fix this by properly comparing the Kconfig symbols against the empty
string. strcmp() would be nicer for this, but GCC does not optimise this
away, probably due to our standalone compiler switches.
Reported-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi WinPlus Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Andre Heider [Fri, 1 Oct 2021 18:29:00 +0000 (19:29 +0100)]
sunxi: Add support for Orange Pi 3
dts file is taken from Linux 5.11-rc1 tag.
The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.
Signed-off-by: Andre Heider <a.heider@gmail.com> Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update] Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Jernej Skrabec [Wed, 6 Jan 2021 17:02:57 +0000 (18:02 +0100)]
sunxi: Add support for Tanix TX6
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.
DT file is taken from Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara [Sat, 14 Nov 2020 17:37:46 +0000 (17:37 +0000)]
net: sun8i-emac: Allow all RGMII PHY modes
So far all GBit users of the sun8i-emac driver were using the "rgmii"
PHY mode, even though this turns out to be wrong. It just worked because
the PHY driver doesn't do the proper setup (yet).
In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the
correct ones.
To allow the DTs to describe the phy-mode correctly, and to stay
compatible with Linux, at least allow those other RGMII modes in the
driver.
This avoids breakage if mainline DTs will be synced with U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
projects / u-boot.git / log
;st=author){kind=link}
