Marek Vasut [Wed, 8 Aug 2018 11:20:29 +0000 (13:20 +0200)]
blk: Increase cache element size
Cache up to 4 kiB entries. 4 kiB is the default block size on ext4, yet
the underlying block layer devices usually report support for 512B . In
most cases, the 512B support is emulated (ie. SD cards, SSDs, USB sticks
etc.) and the real block size of those devices is much bigger.
To avoid performance degradation with such devices and FS setup, bump
the maximum cache entry size to 4 kiB.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Makefile: run CONFIG_BOARD_SIZE_LIMIT against .img
With the current Makefile, CONFIG_BOARD_SIZE_LIMIT is used to check
the U-Boot binary without devicetree only. This produces wrong results
when OF_SEPARATE is used.
To fix this, run the CONFIG_BOARD_SIZE_LIMIT check on all .img binaries
as well.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Fri, 11 Jan 2019 10:42:27 +0000 (19:42 +0900)]
kbuild: add .SECONDARY special target to scripts/Kbuild.include
Based on the following Linux commits:
- 54a702f70589 ("kbuild: mark $(targets) as .SECONDARY and remove
.PRECIOUS markers")
- 8e9b61b293d9 ("kbuild: move .SECONDARY special target to
Kbuild.include")
GNU Make automatically deletes intermediate files that are updated
in a chain of pattern rules.
Example 1) %.dtb.o <- %.dtb.S <- %.dtb <- %.dts
Example 2) %.o <- %.c <- %.c_shipped
A couple of makefiles mark such targets as .PRECIOUS to prevent Make
from deleting them, but the correct way is to use .SECONDARY.
.SECONDARY
Prerequisites of this special target are treated as intermediate
files but are never automatically deleted.
.PRECIOUS
When make is interrupted during execution, it may delete the target
file it is updating if the file was modified since make started.
If you mark the file as precious, make will never delete the file
if interrupted.
Both can avoid deletion of intermediate files, but the difference is
the behavior when Make is interrupted; .SECONDARY deletes the target,
but .PRECIOUS does not.
The use of .PRECIOUS is relatively rare since we do not want to keep
partially constructed (possibly corrupted) targets.
.SECONDARY with no prerequisites causes all targets to be treated as
secondary. This agrees the policy of Kbuild.
scripts/Kbuild.include seems a suitable place to add it because it is
included from almost all sub-makes.
If Make gets a fatal signal while a shell is executing, it may delete
the target file that the recipe was supposed to update. This is needed
to make sure that it is remade from scratch when Make is next run; if
Make is interrupted after the recipe has begun to write the target file,
it results in an incomplete file whose time stamp is newer than that
of the prerequisites files. Make automatically deletes the incomplete
file on interrupt unless the target is marked .PRECIOUS.
The situation is just the same as when the shell fails for some reasons.
Usually when a recipe line fails, if it has changed the target file at
all, the file is corrupted, or at least it is not completely updated.
Yet the file’s time stamp says that it is now up to date, so the next
time Make runs, it will not try to update that file.
However, Make does not cater to delete the incomplete target file in
this case. We need to add .DELETE_ON_ERROR somewhere in the Makefile
to request it.
scripts/Kbuild.include seems a suitable place to add it because it is
included from almost all sub-makes.
Masahiro Yamada [Thu, 10 Jan 2019 14:11:39 +0000 (23:11 +0900)]
kbuild: fix parallel build race caused by u-boot.cfg regeneration
Multiple people have reported intermittent build failure in parallel
building.
Kever Yang reported this issue some time ago [1], but I could not
get enough clue at that time.
This time, Richard Purdie provided a full build log [2], which was
very helpful for me to root-cause it.
The cause of the problem is commit 0d982c585330 ("Makefile: add
dependencies to regenerate u-boot.cfg when lost").
That commit added the 'cfg' as the prerequisite of the 'all' target,
so the parallel build tries to run it simultaneously, then regenerates
a symlink while building objects.
When u-boot.cfg is accidentally lost, let's rebuild it before
descending into any subdirectories.
Also, what is annoying is u-boot.cfg is currently regenerated every
time since it depends on FORCE. We can get rid of all the prerequisites
of u-boot.cfg because u-boot.cfg is rebuilt anyway as the byproduct of
auto.conf when a user updates the .config file.
serial: ns16550: fix debug uart putc called before init
If _debug_uart_putc() is called before _debug_uart_init(), the
ns16550 debug uart driver hangs in a tight loop waiting for the
tx FIFO to get empty.
As this can happen via a printf sneaking in before the port calls
debug_uart_init(), introduce a config option to ignore characters
before the debug uart is initialized.
This is done by reading the baudrate divisor and aborting if is zero.
The Kconfig option is required as reading the baudrate divisor does
not seem to work for all ns16500 compatibles (which is why the last
attempt on this has been reverted in 1a67969a99).
Tested on socfpga_cyclone5_socrates.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Lokesh Vutla [Tue, 8 Jan 2019 13:58:35 +0000 (19:28 +0530)]
xyz-modem: Fix timeout loop waiting with WATCHDOG
Commit 2c77c0d6524eb ("xyz-modem: Change getc timeout loop waiting")
fixes the loop delay when using a hw watchdog, assuming that watchdog
kicking is taken care of by getc(). But the xyzmodem driver tries to
do a getc only after confirming that a character is available like below:
while (!tstc()) {
till timeout;
}
if (tstc())
*c = getc();
and getc() does a watchdog reset only if it fails to see a character.
In this case, getc() always sees a character and never does a
watchdog reset. So to make sure that watchdog doesn't get reset
while loading the file, do a watchdog reset just before starting the
image loading.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Mon, 7 Jan 2019 20:23:38 +0000 (21:23 +0100)]
lib: uuid: Do not enable UUID command SPL
The uuid command is only really useful in U-Boot, but it's useless in
SPL. Worse yet, it pulls in various environment manipulation functions
as it call env_set(). Do not compile the command in in SPL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Mon, 7 Jan 2019 20:23:22 +0000 (21:23 +0100)]
spl: ymodem: Add support for loading gzip compressed uImage
Add support for gunzip-ing gzip-compressed uImages in the SPL Ymodem code.
Loading data over Ymodem can be gruelingly slow, gzip-ing the data can
reduce that aggravating slowness at least slightly (depends on the data,
u-boot.bin compresses to ~1/3 of it's original size on ARM64), hence add
optional support for decompressing gzip-compressed uImages.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Thu, 3 Jan 2019 21:09:44 +0000 (22:09 +0100)]
cmd: mmc: Invalidate MMC block cache after init
Make sure the block cache is cleared for the MMC device after it was
reinitialized to avoid having any stale data in the cache, like e.g.
partition tables or such.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
Marek Vasut [Thu, 3 Jan 2019 20:19:24 +0000 (21:19 +0100)]
mmc: Add support for downgrading HS200/HS400 to HS mode
The mmc_select_mode_and_width() function can be called while the card
is in HS200/HS400 mode and can be used to downgrade the card to lower
mode, e.g. HS. This is used for example by mmc_boot_part_access_chk()
which cannot access the card in HS200/HS400 mode and which is in turn
called by saveenv if env is in the MMC.
In such case, forcing the card clock to legacy frequency cannot work.
Instead, the card must be switched to HS mode first, from which it can
then be reprogrammed as needed.
However, this procedure needs additional code changes, since the current
implementation checks whether the card correctly switched to HS mode in
mmc_set_card_speed(). The check only expects that the card will be going
to HS mode from lower modes, not from higher modes, hence add a parameter
which indicates that the HS200/HS400 to HS downgrade is happening. This
makes the code send the switch command first, reconfigure the controller
next and finally perform the EXT_CSD readback check. The last two steps
cannot be done in reverse order as the card is already in HS mode when
the clock are being switched on the controller side.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
omap3: igep00x0: Remove USB support due DM_USB deadline
The USB support for this board was never really tested, in fact, the
presence of these options are more a copy & paste error from the
Beagleboard than a feature that really was used. As doesn't work, remove
for now. If someone at some point want to add this support he'll need to
migrate the board to use CONFIG_DM_USB instead.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The IGEP0032 board was never officially pushed upstream and actually I
don't have access to this hardware, unless someone with the hardware
wants to start working on this doesn't makes sense have this defconfig
here. So remove it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC
controllers in this SoC, first one used for eMMC, second one used
for SD card and third one is not used by u-boot.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver
model.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Enable this on poplar] Signed-off-by: Tom Rini <trini@konsulko.com>
Shawn Guo [Tue, 18 Dec 2018 09:52:06 +0000 (17:52 +0800)]
poplar: add DWC2 OTG gadget support
It enables DWC2 OTG gadget driver support for Poplar board. As
usb2_phy_init() is being always called from board_init(), we can save
the call from board_usb_init().
Booting an image currently sets the environment variable "fdtaddr"
by calling into 'cmd/fdt.c'. As a result, linking U-Boot fails if
CMD_FDT is not enabled.
Fix this by adding 'if (CONFIG_IS_ENABLED(CMD_FDT))' to the two
places where 'set_working_fdt_addr()' is called.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
CPU: Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 33C
Reset cause: POR
Board: MX6 HummingBoard2
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
---> hangs
which is caused by the following infinite loop inside esdhc_send_cmd_common()
while (!(esdhc_read32(®s->irqstat) & flags))
;
Instead of looping forever, provide an exit path so that a timeout
error can be propagated in the case irqstat does not report
any interrupts, which may happen when no eMMC is populated on
board.
Fabio Estevam [Sat, 29 Dec 2018 12:02:24 +0000 (10:02 -0200)]
imx8mq_evk_defconfig: Move file system options to Kconfig
Chris Spencer reports that when enabling ext4 read support without
also enabling write support the following error is seen:
fs/fs.c:198:12: error: 'ext4_write_file' undeclared here (not in a
function); did you mean 'ext4_read_file'?
.write = ext4_write_file,
^~~~~~~~~~~~~~~
Fix this problem by moving these options to Kconfig.
Reported-by: Chris Spencer <spencercw@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
Alex Elder [Tue, 18 Dec 2018 03:08:18 +0000 (11:08 +0800)]
poplar: save environment at a different offset
Change CONFIG_ENV_OFFSET for Poplar to be 1MB further into the eMMC
than before. This puts it immediately prior to the space we are
reserving offset 0x200000-0x400000 for UEFI to save its persistent
data. Define CONFIG_ENV_SIZE as a product of env_mmc_nblks and the
sector size, like CONFIG_ENV_OFFSET is.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tom Rini [Fri, 11 Jan 2019 14:54:44 +0000 (09:54 -0500)]
Revert "fs: fat: assign rootdir sector when accessing root directory"
This particular commit is causing a regression on stih410-b2260 and
other platforms when reading from FAT16. Noting that I had rebased the
original fix from Thomas onto then-current master, there is also
question from Akashi-san if the change is still needed after other FAT
fixes that have gone in.
As reported by Alex Kiernan the above optimization introduces a
regression in the below use case where:
1. Device has defined 'u-boot,dm-spl' property (@ eMMC DTS node)
2. The device downloads its MLO/SPL via UART (not eMMC - the eMMC pinmux
pins are NOT probed/configured in MLO/SPL).
3. The loaded via UART MLO/SPL wants to load Linux from eMMC. In this case
the DM core and pinctrl uclass checks 'u-boot,dm-spl' and don't
configure pins (as it thinks that those were initialized in MLO/SPL).
As we are very close to release - please revert this commit.
Reported-by: Alex Kiernan <alex.kiernan@gmail.com> Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
dm: usb: gadget: Fix boot breakage on sunxi platforms
Fixes commit 013116243950 ("dm: usb: create a new UCLASS ID for USB gadget
devices")
The UCLASS_DRIVER for id UCLASS_USB_GADGET_GENERIC needs to be declared
even for platforms that do not enable DM_USB_GADGET. Otherwise the driver
for their usb peripheral controller fails to bind.
Reported-by: Priit Laes <plaes@plaes.org> Reported-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Tested-by: Priit Laes <plaes@plaes.org> Acked-by: Jagan Teki <jagan@openedev.com>
dm: usb: udc: Use SEQ_ALIAS to index the USB gadget ports
dfu, fastbot and other usb gadget commands take the USB port index as a
parameter. Currently this index is assigned in the order of the driver
bindings.
Changing this behavior using the SEQ_ALIAS feature. This option assign to
the device a SEQ number based on its alias (if it exists)
To use it we must set the DM_UC_FLAG_SEQ_ALIAS flag and follow the existing
naming convention: use "usb" for the name of the gadget UCLASS_DRIVER
(same as for the UCLASS_USB).
If no alias is provided, then the index falls back to the order in which
the bindings took place.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reported-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Peng Fan [Sat, 15 Dec 2018 12:19:58 +0000 (12:19 +0000)]
tools: imx8image: set dcd_skip to true
To B0[+] chips, dcd_skip needs to be true. For A0 chip, it needs
to be false, however A0 chip is no longer being supported anymore.
Considering we are moving code from imx-mkimage to uboot mkimage,
to make sure we not introduce some surprise, we still keep dcd_skip
code there.
Peng Fan [Sat, 15 Dec 2018 12:19:46 +0000 (12:19 +0000)]
clk: imx8: fix build warning
When build clk driver in spl, met the warning:
"
drivers/clk/imx/clk-imx8.c:21:25: warning: ‘imx8_clk_names’ defined but not used [-Wunused-variable]
static struct imx8_clks imx8_clk_names[] = {
^~~~~~~~~~~~~~
"
Soeren Moch [Sat, 5 Jan 2019 08:31:18 +0000 (09:31 +0100)]
board: tbs2910: Remove FIT support in defconfig to reduce u-boot size
The current defconfig build generates a u-boot.imx file that is too large
for the available space on a eMMC/SD card. Installing this file overwrites
the u-boot environment. So disable the unused FIT support to reduce the
size of the u-boot binary.
Chris Spencer [Thu, 20 Dec 2018 09:25:24 +0000 (09:25 +0000)]
imx: Add Makefile dependency for mkimage_fit_atf.sh
The mkimage_fit_atf.sh SPL FIT generator script requires
u-boot-nodtb.bin, but this was not enforced by the Makefile. This could
cause the generator script to be executed before u-boot-nodtb.bin has
been created.
Signed-off-by: Chris Spencer <christopher.spencer@sea.co.uk> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Stefan Agner [Tue, 4 Dec 2018 10:10:21 +0000 (11:10 +0100)]
ARM: vf610: ddrmc: do not write CR79 by default
The current value CTLUPD_AREF(0) is the reset value of the register,
so there is no need to write a value. If needed, the register can be
written using board specific CR settings.
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Stefan Agner [Tue, 4 Dec 2018 10:10:18 +0000 (11:10 +0100)]
toradex: colibri_vf: fix memory initialization
Commit 3f353ceccbbb ("vf610: refactor DDRMC code") changed on-die
termination (ODT) values from 120 Ohm to 60 Ohm and enabled a static
read/write leveling which has not been tested with this board. This
commit reverts both changes and makes sure that memory gets
initialized as it has been done before the mentioned commit.
Fixes: 3f353ceccbbb ("vf610: refactor DDRMC code") Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Stefan Agner [Fri, 14 Dec 2018 14:26:00 +0000 (15:26 +0100)]
ARM: vf610: ddrmc: program Dummy DDRBYTE1/2
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Patrice Chotard [Fri, 4 Jan 2019 09:55:06 +0000 (10:55 +0100)]
gpio: stm32f7: Fix SPL code size
In order to keep SPL code size below the 32Kb limit,
put under CONFIG_SPL_BUILD flag all unused code in SPL.
This is needed for stm32f7xx board which are using SPL.
Patrice Chotard [Fri, 4 Jan 2019 09:55:05 +0000 (10:55 +0100)]
gpio: stm32f7: Fix gpio bank hole management
In case "gpio-ranges" property is not present in device tree,
use default value for gpio_count and gpio_range.
This fixes an issue on stm32 F7 and H7 boards where "pinmux status -a"
command didn't return any pin status due to the fact that both stm32 F7
and H7 board DT doesn't use the gpio-ranges property.
Sam Protsenko [Fri, 4 Jan 2019 20:09:08 +0000 (22:09 +0200)]
arm: ti: boot: Remove legacy Android partitions
Remove unused Android partitions:
- efs, crypto, cache: we don't use it anymore (images are not built
in AOSP
- ipu1, ipu2: IPU firmware is now a part of vendor image and doesn't
reside as a separate partition
While at it, rename "reserved" partition to "uboot-env", as it's
actually stores U-Boot environment.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Ye Li [Fri, 4 Jan 2019 09:34:24 +0000 (09:34 +0000)]
env: sata: Add missed env location for SATA boot
The env location label ENVL_ESATA is missed in location tables, so
when we configure the ENV in SATA, u-boot fails to get correct env
location and cause boot hang in board_f.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Fri, 4 Jan 2019 09:24:14 +0000 (09:24 +0000)]
arm: Round the dma_alloc_coherent memory size to cache line aligned
When running usb dwc3 gadget driver, we meet random USB enumeration failure in fastboot.
The root cause is a cache coherence issue. When it happens, the ctrl_req in
gadget driver is allocated at 0xfe932f40, and the usb_composite_dev (cdev)
is allocated at 0xfe932f60. So after we submit the setup request (cache flushed) to USB
controller, any accessing to usb_composite_dev variable will cause the cache line refill, then
when setup transfer is completed, reading the setup data in ctrl_req will gets old value from
cache not from memory.
The ctrl_req is allocated by API dma_alloc_coherent, but u-boot don't have cohernet memory.
so it still needs cache maintain operations before/after HW accessing. Since the cache flush or
invalidate bases on cache line, so when the allocated memory size is not cache line aligned,
potentially it may meet such issue.
This patch modifies the dma_alloc_coherent API to round the size to cache line aligned.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
igep003x: MAINTAINER: Remove myself as maintainer and add Javier
I can't continue maintaining the board because I don't have access to the
hardware anymore, so remove myself from the entry and add Javier who has
volunteered to help and maintain the board.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Javier Martínez Canillas <javier@dowhile0.org>
Tom Rini [Thu, 27 Dec 2018 14:22:55 +0000 (09:22 -0500)]
Add a github template telling people to not use pull requests there
On our mirror account on github we have gotten a handful of pull
requests. At this time github does not allow you to disable pull
requests on a project. The generally suggested work-around is to add a
pull request template that tells people to not use that workflow. Add
one here that points to the wiki page on submitted patches.
Andre Przywara [Mon, 17 Dec 2018 10:05:45 +0000 (10:05 +0000)]
mmc: bring back partition init for non-DM MMC drivers
Commit d0851c893706 ("blk: Call part_init() in the post_probe() method")
removed the call to part_init() in mmc.c, as this is done by the DM_MMC
framework.
However Allwinner is (still) relying on a non-DM MMC driver, so we are
now missing the implicit partition init, leading to failing MMC accesses
due to the missing partition information.
Bring the call back just for non-DM MMC driver to fix this regression.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Soeren Moch <smoch@web.de>
Andre Przywara [Mon, 17 Dec 2018 10:05:44 +0000 (10:05 +0000)]
sunxi: drop default SPL_LIBDISK_SUPPORT enablement
There is no code for using partition labels in the Allwinner SPL port.
Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was
meant to guard partition code for the SPL.
Remove the "imply" line in the Kconfig to make this obvious and avoid
unneeded code inclusions, helping to keep the H6 SPL code small.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 8 Jan 2019 03:57:56 +0000 (22:57 -0500)]
Makefile: Correct logic for DM_SCSI + unconverted drivers check
When checking for boards that are enabling a SATA driver that isn't
converted to DM yet we need to be sure to not also trip over boards that
do set CONFIG_DM_SCSI by itself, as that is not a bug.
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com> Fixes: ea9d7c17fc4c ("dm: MIGRATION: Add migration plan for CONFIG_SATA") Signed-off-by: Tom Rini <trini@konsulko.com>
projects / u-boot.git / log
