Marek Vasut [Sun, 17 Sep 2023 14:08:35 +0000 (16:08 +0200)]
pinctrl: renesas: Add support for 1.8V/2.5V I/O voltage levels
Currently, the Renesas pin control driver supports pins that can switch
their I/O voltage levels between either 1.8V and 3.3V, or between 2.5V
and 3.3V. However, some SoCs have pins that can switch between 1.8V and
2.5V.
Add support for this by replacing the separate SH_PFC_PIN_CFG_IO_VOLTAGE
capability and voltage level flags by a 2-bit field, to cover three
possible I/O voltage switching options.
Ported from Linux kernel commit by Geert Uytterhoeven: b88e733ac517 ("pinctrl: renesas: Add support for 1.8V/2.5V I/O voltage levels")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Sun, 17 Sep 2023 11:49:30 +0000 (13:49 +0200)]
ARM: dts: renesas: Add compatible properties to KSZ9031 Ethernet PHYs on Salvator-X boards
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 Salvator-X boards. This allows software
to identify the PHY model at any time, regardless of the state of
the PHY reset line.
This is a fix for missed addition of these properties on Salvator-X
boards.
Simon Glass [Thu, 7 Sep 2023 16:00:19 +0000 (10:00 -0600)]
buildman: Start the clock when the build starts
The Kconfig and maintainer processing can take a while, sometimes 5
seconds or more. This skews the timing printed by buildmand when the build
completes. Start the clock when the threads start to avoid this problem.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Tom Rini <trini@konsulko.com>
AKASHI Takahiro [Wed, 23 Aug 2023 01:49:47 +0000 (10:49 +0900)]
cmd: dm: allow for selecting uclass and device
The output from "dm tree" or "dm uclass" is a bit annoying
if the number of devices available on the system is huge.
(This is especially true on sandbox when I debug some DM code.)
With this patch, we can specify the uclass name or the device
name that we are interested in in order to limit the output.
For instance,
=> dm uclass usb
uclass 121: usb
0 usb@1 @ 0bcff8b0, seq 1
Jonas Karlman [Sun, 20 Aug 2023 22:03:18 +0000 (22:03 +0000)]
dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation
Nodes with bootph-pre-sram/ram props are bound in multiple phases:
1. At TPL (bootph-pre-sram) or SPL (bootph-pre-ram) phase
2. At U-Boot proper pre-relocation phase
3. At U-Boot proper normal phase
However the binding and U-Boot Driver Model documentation indicate that
only nodes marked with bootph-all or bootph-some-ram should be bound in
the U-Boot proper pre-relocation phase.
Change ofnode_pre_reloc to report a node with bootph-pre-ram/sram prop
with a pre-reloc status only after U-Boot proper pre-relocation phase.
Also update the ofnode_pre_reloc documentation to closer reflect the
binding and driver model documentation.
This changes behavior of what nodes are bound in the U-Boot proper
pre-relocation phase. Change to bootph-all or add bootph-some-ram prop
to restore prior behavior.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 22 Sep 2023 15:16:22 +0000 (11:16 -0400)]
Merge tag 'x86-pull-20230922' of https://source.denx.de/u-boot/custodians/u-boot-x86 into next
- Add bootstd support to 64-bit efi payload
- Fix a bug of missing setting size of initrd in pxeboot
- Allow Python packages to be dropped
- Reland "x86: Move FACP table into separate functions"
- Fixes for chromebook_link64 and chromebook_samus_tpl
- Fixes and improvements for coreboot
- x86 documentation updates
Simon Glass [Wed, 20 Sep 2023 13:29:51 +0000 (07:29 -0600)]
efi: Use the installed SMBIOS tables
U-Boot should set up the SMBIOS tables during startup, as it does on x86.
Ensure that it does this correctly on non-x86 machines too, by creating
an event spy for last-stage init.
Tidy up the installation-condition code while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 20 Sep 2023 13:29:49 +0000 (07:29 -0600)]
bootstd: Keep track of use of usb stop
When 'usb stop' is run, doing 'bootflow scan' does not run the USB hunter
again so does not see any devices. Fix this by telling bootstd about the
state of USB.
Simon Glass [Wed, 20 Sep 2023 03:00:13 +0000 (21:00 -0600)]
x86: smbios: Add a Kconfig indicating SMBIOS-table presence
When booted from coreboot, U-Boot does not build the SMBIOS tables, but
it should still pass them on to the OS. Add a new option which indicates
whether SMBIOS tables are present, however they were built.
Flip the ordering so that the dependency is listed first, which is less
confusing.
Adjust GENERATE_SMBIOS_TABLE to depend on this new symbol.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 20 Sep 2023 03:00:11 +0000 (21:00 -0600)]
x86: coreboot: Enable VIDEO_COPY
At least on modern machines the write-back mechanism for the frame buffer
is quite slow when scrolling, since it must read the entire frame buffer
and write it back.
Enable the VIDEO_COPY feature to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 20 Sep 2023 03:00:08 +0000 (21:00 -0600)]
x86: coreboot: Enable CONFIG_SYS_NS16550_MEM32
The debug UART on modern machines uses a 32-bit wide transfer. Without
this, setting debug output causes a hang or no output. It is not obvious
(when enabling CONFIG_DEBUG_UART) that this is needed.
Enable 32-bit access to avoid this trap.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 20 Sep 2023 03:00:07 +0000 (21:00 -0600)]
x86: coreboot: Look for DBG2 UART in SPL too
If coreboot does not set up sysinfo for the UART, SPL currently hangs.
Use the DBG2 technique there as well. This allows coreboot64 to boot from
coreboot even if the console info is missing from sysinfo
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Wed, 20 Sep 2023 03:00:05 +0000 (21:00 -0600)]
x86: Set the CPU vendor in SPL
We don't read this information in 64-bit mode, since we don't have the
macros for doing it. Set it to Intel by default. This allows the TSC timer
to work correctly.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 10 Sep 2023 19:13:02 +0000 (13:13 -0600)]
x86: Update cbmem driver
This driver is not actually built since a Kconfig was never created for
it.
Add a Kconfig (which is already implied by COREBOOT) and update the
implementation to avoid using unnecessary memory. Drop the #ifdef at the
top since we can rely on Kconfig to get that right.
To enable it (in addition to serial and video), use:
setenv stdout serial,vidconsole,cbmem
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[Modified the comment about overflow a little bit] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 7 Sep 2023 15:58:20 +0000 (09:58 -0600)]
x86: dm: Mark driver model as dead when disabling CAR
When turning off CAR, set the flag to make sure that nothing tries to use
driver model in SPL before jumping to U-Bot proper, since its tables are
in CAR.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 7 Sep 2023 15:58:13 +0000 (09:58 -0600)]
dm: core: Allow marking driver model as dead
On x86 devices we use CAR (Cache-As-RAM) to hold the malloc() region in
SPL, since SDRAM is not set up yet. This means that driver model stores
its tables in this region.
When preparing to jump from SPL to U-Boot proper, we must disable CAR, so
that the CPU can uses the caches normally. This means that driver model
tables become inaccessible. From there until we jump to U-Boot proper, we
must avoid using driver model.
This is only a problem on boards which operate this way, for example
chromebook_link64
Add a flag to indicate that driver model is dead and should not be used.
It can be used in SPL to avoid hanging the machine.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Fri, 1 Sep 2023 17:27:10 +0000 (11:27 -0600)]
x86: Prevent from missing the FADT chaining
Recent approach with FADT writer shows that there is
a room for subtle errors. Prevent this from happening
again by introducing acpi_add_fadt() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Fri, 1 Sep 2023 17:27:09 +0000 (11:27 -0600)]
Reland "x86: Move FACP table into separate functions""
Each board has its own way of creating this table. Rather than calling the
acpi_create_fadt() function for each one from a common acpi_write_fadt()
function, just move the writer into the board-specific code.
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Simon Glass [Thu, 31 Aug 2023 17:20:53 +0000 (11:20 -0600)]
x86: coreboot: Avoid a declaration after a label
Declare the global_data pointer at the top of the file, to avoid an
error:
arch/x86/include/asm/global_data.h:143:35: error: a label can
only be part of a statement and a declaration is not a statement
board/coreboot/coreboot/coreboot.c:60:2: note: in expansion of macro
‘DECLARE_GLOBAL_DATA_PTR’
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Mike Frysinger <vapier@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Thu, 31 Aug 2023 17:20:52 +0000 (11:20 -0600)]
Allow Python packages to be dropped
When building in a portage chroot, we do not have the environment needed
to build pylibfdt. It is instead build as a separate package.
Provide a build option to tell U-Boot to skip this part of the build. We
still need it to use binman, etc. but don't need it to build its
dependencies.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Mike Frysinger <vapier@chromium.org>
[s/build bytes/builds bytes in tools.rst] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Enable bootstd support for U-Boot at VirtualBox described at
https://source.denx.de/u-boot/u-boot/-/blob/master/doc/develop/bootstd.rst
This is used to boot system images at Virtualbox via
- distroboot (extlinux.conf)
- boot script
Signed-off-by: Thomas Mittelstaedt <thomas.mittelstaedt@bosch.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[Added 'efi-payload64' tag] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot at VirtualBox must load Linux and boot configuration from disk devices.
Here the discs at AHCI (scsi) bus are used to load the needed boot data.
Signed-off-by: Thomas Mittelstaedt <thomas.mittelstaedt@de.bosch.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[Added 'efi-payload64' tag and rebased on top of u-boot/master] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Thu, 21 Sep 2023 14:51:58 +0000 (10:51 -0400)]
Merge tag 'xilinx-for-v2024.01-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2024.01-rc1
clk:
- Dont return error when assigned-clocks is empty or missing
dm:
- Support reading a single indexed u64 value
- Add support for reading bootscript address/flash address from DT
cmd:
- Fix flash_is_unlocked API
fpga:
- Define fpga_load() for debug build
global:
- U-Boot project name cleanup (next2)
net:
- zynq_gem: Use generic_phy_valid() helper
- axienet: Convert to ofnode functions
- gmii2rgmii: Read bridge address from DT
pytest:
- skip tpm2_startup when env__tpm_device_test_skip=True
spi-nor:
- Add mx25u25635f support
- zynqmp_qspi: Tune cache behavior
trace:
- Fix flyrecord alignment issue
xilinx:
- Move scriptaddr to DT as bootscr-address
- Pick script_offset_f/script_size_f from DT as bootscr-flash-offset/size
- Do not generate distro boot variables if disabled
versal:
- Extend memory ranges to cover HBM
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices
- Clean mini targets bootcommand
- Fix clock driver
versal-net:
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices
zynqmp;
- Allow AES to run from SPL
- Enable CMD_KASLRSEED
- Add proper dependencies for USB and remove ZYNQMP_USB
- Fix user si570 default frequency for zcu* boards
- Cover SOM rev2 revision
- Various DT changes
- Add firmware and pinctrl support for tristate configuration
(high impedance/output enable)
- Add output-enable pins to SOMs
- Fix distroboot prioritization in connection to available devices
- Read bootscript address/flash address from DT
- Fix pcap_prog address
spi: zynqmp_qspi: Workaround for small data cache issue
Cache related issues are seen with small sized data reads.
Due to this, proper data is not read. Also some times sf probe
fails randomly. To workaround this issue, invalidate dcache after read DMA
is triggered.
spi: zynqmp_qspi: Change flush cache to invalidate cache
Before DMA read, ideally cache should be invalidated, so that data from
memory will be updated to cache after DMA is completed. But
flush_dcache_range is being used which is incorrect. Change
flush_dcache_range to invalidate_dcache_range.
Michal Simek [Fri, 15 Sep 2023 12:12:05 +0000 (14:12 +0200)]
trace: Fix alignment logic in flyrecord header
Current alignment which is using 16 bytes is not correct in connection to
trace_clocks description and it's length.
That's why use start_addr variable and record proper size based on used
entries.
Michal Simek [Fri, 15 Sep 2023 12:12:04 +0000 (14:12 +0200)]
trace: Move trace_clocks description above record offset calculation
Flyrecord tracing data are page aligned that's why it is necessary to
calculate alignment properly. Because trace_clocks description is the part
of record length it is necessary to have information about length earlier.
cmd: sf: Fix the flash_is_unlocked api size parameter
When flash erase is called with size parameter, code is checking
if sectors are locked or not. But for checking, the whole device
length minus offset is used instead of actual size which should
be erased. That's why when only some sectors are locked it is
not possible to erase unlocked sectors.
The length is calculated as "length = max_chipsize - offset",
flash_is_unlocked() api is getting updated with length which is
incorrect. Fix this flash_is_unlocked() api by passing the size
parameter.
ZynqMP> sf erase 0 100000
len=0x8000000 which is flash size
size=0x100000
We need to update the size in the flash_is_unlocked() api and not
the length.
cmd: thordown: Add proper dependency for CMD_THOR_DOWNLOAD
When CONFIG_CMD_USB and CONFIG_USB are disabled some compilation errors are seen as below.
cmd/thordown.o: in function `usb_gadget_initialize':
include/linux/usb/gadget.h:981: undefined reference to `board_usb_init'
cmd/thordown.o: in function `do_thor_down':
cmd/thordown.c:68: undefined reference to `g_dnl_unregister'
cmd/thordown.o: in function `usb_gadget_release':
include/linux/usb/gadget.h:986: undefined reference to `board_usb_cleanup'
cmd/thordown.o: in function `do_thor_down':
cmd/thordown.c:41: undefined reference to `g_dnl_register'
cmd/thordown.c:48: undefined reference to `thor_init'
cmd/thordown.c:56: undefined reference to `thor_handle'
gnu/aarch64/lin/aarch64-linux/bin/aarch64-linux-gnu-ld.bfd: line 4: 8485
Segmentation fault (core dumped) $CC --sysroot=$LIBC
--no-warn-rwx-segment "$@"
Makefile:1779: recipe for target 'u-boot' failed
make: *** [u-boot] Error 139
make: *** Deleting file 'u-boot'
Add dependency of USB_GADGET_DOWNLOAD for CONFIG_CMD_THOR_DOWNLOAD to fix the errors.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com> Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com> Reviewed-by: Tom Rini <trini@konsulko.com> Link: https://lore.kernel.org/r/20230904031528.11817-2-venkatesh.abbarapu@amd.com Signed-off-by: Michal Simek <michal.simek@amd.com>
For reference clocks, PM_CLK_GET_PARENT call is not allowed.
PM_CLK_GET_PARENT only allowed for MUX clocks. Rename the
versal_clock_ref() with versal_clock_get_ref_rate() for better
readability. Fix the versal_clock_get_ref_rate function by
passing the parent_id, and check whether the parent_id
belongs to ref_clk or pl_alt_ref_clk.
Also adding the function versal_clock_get_fixed_factor_rate()
if the clk_id belongs to the fixed factor clock.
arm64: zynqmp: Fix i2c address for si570_user1 clock
Correct the i2c address for si570 oscillator that generates the si570_user1
clock. i2c address was changed by commit b6a8c603d680 ("arm64: zynqmp: Fix
i2c addresses for vck190 SC") because address in node name wasn't aligned
with reg property. But actual 0x5f address is correct which is quite rare
because all other si570s are at 0x5d.
arm64: versal: Add no-wp DT property in OSPI flash node
Added no-wp DT property in OSPI flash node for all board dts & dtsi files
on which the WP# signal of the OSPI flash device is not connected. If this
property is set, then the software will avoid setting the status register
write disable (SRWD) bit in status register during status register
write operation.
Michal Simek [Mon, 11 Sep 2023 14:10:46 +0000 (16:10 +0200)]
arm64: zynqmp: Rename xlnx, mio_bank to xlnx, mio-bank for DLC21
xlnx,mio_bank was used in past but it was renamed to xlnx,mio-bank because
'_' in property shoudln't be used. There is no impact on the platform
because if the properly is not defined bank 0 is default. Bank 0 and 1 have
the same configuration that's why there shouldn't be any issue.
net: phy: xilinx-gmii2rgmii: Removed hardcoded phy address 0 for bridge
Current code expects bridge phy address at 0 which is not correct
expectation because bridge phy address is configurable.
That's why update the code to read reg property to figure it out
where bridge is and use it in phy creation code.
xilinx: zynqmp: Do not setup boot_targets if driver is not enabled
SOC can boot in the device which is not accessible from APU and running
this is detected as error which ends up in stopping boot process.
Boot mode detection and logic around is present to setup priority on boot
devices that SOC boot device is likely also used for booting OS.
Change logic to detect this case with showing message about it but don't fail
in boot process and don't prioritize boot device in this case.
xilinx: versal: Do not setup boot_targets if driver is not enabled
SOC can boot in the device which is not accessible from APU and running
this is detected as error which ends up in stopping boot process.
Boot mode detection and logic around is present to setup priority on boot
devices that SOC boot device is likely also used for booting OS.
Change logic to detect this case with showing message about it but don't fail
in boot process and don't prioritize boot device in this case.
xilinx: versal-net: Do not setup boot_targets if driver is not enabled
SOC can boot in the device which is not accessible from APU and running
this is detected as error which ends up in stopping boot process.
Boot mode detection and logic around is present to setup priority
on boot devices that SOC boot device is likely also used for booting OS.
Change logic to detect this case with showing message about it but don't
fail in boot process and don't prioritize boot device in this case.
Michal Simek [Thu, 31 Aug 2023 07:04:28 +0000 (09:04 +0200)]
xilinx: board: Add support to pick bootscr flash offset/size from DT
Location of bootscript in flash can be specified via /options/u-boot DT
node by using bootscr-flash-offset and bootscr-flash-size properties.
Values should be saved to script_offset_f and script_size_f variables.
Variables are described in doc/develop/bootstd.rst as:
script_offset_f
SPI flash offset from which to load the U-Boot script, e.g. 0xffe000
script_size_f
Size of the script to load, e.g. 0x2000
Both of them are used by sf_get_bootflow() in drivers/mtd/spi/sf_bootdev.c
to identify bootscript location inside flash.
ofnode_read_bootscript_flash() reads bootscript address from
/options/u-boot DT node. bootscr-flash-offset and bootscr-flash-size
properties are read and values are filled. When bootscr-flash-size is not
defined, bootscr-flash-offset property is unusable that's why cleaned.
Both of these properties should be defined to function properly.
Neal Frager [Thu, 31 Aug 2023 14:27:53 +0000 (16:27 +0200)]
arm64: zynqmp: Add output-enable pins to SOMs
Now that the zynqmp pinctrl driver supports the tri-state registers, make
sure that the pins requiring output-enable are configured appropriately for
SOMs.
Without it, all tristate setting for MIOs, which are not related to SOM
itself, are using default configuration which is not correct setting.
It means SDs, USBs, ethernet, etc. are not working properly.
In past it was fixed through calling tristate configuration via bootcmd:
usb_init=mw 0xFF180208 2020
kv260_gem3=mw 0xFF18020C 0xFC0 && gpio toggle gpio@ff0a000038 && \
gpio toggle gpio@ff0a000038
xilinx: board: Add support to pick bootscr address from DT
The bootscript is expected at a default address specific to each
platform.
When high speed memory like Programmable Logic Double Data Rate RAM
(PL DDR RAM) or Higher Bandwidth Memory RAM (HBM) is used the boot.scr
may be loaded at a different offset. The offset needs to be set through
setenv. Due to the default values in some cases the boot.scr is falling
in between the kernel partition.
The bootscript address or the bootscript offset is fetched directly from
the DT and updated in the environment making it easier for automated
flows.
ofnode_read_bootscript_address() reads bootscript address from
/options/u-boot DT node. bootscr-address or bootscr-ram-offset properties
are read and values are filled. bootscr-address has higher priority than
bootscr-ram-offset and the only one should be described in DT.
clk: Dont return error when assigned-clocks is empty or missing
There is a chance that assigned-clock-rates is given and assigned-clocks
could be empty. Dont return error in that case, because the probe of the
corresponding driver will not be called at all if this fails.
Better to continue to look for it and return 0.
arm64: versal-net: Enable the config CMD_KASLRSEED
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data
structures at a random address at each boot.The bootloader
supports randomizing the virtual address at which the kernel image
is loaded. The bootloader must provide entropy by passing a random
u64 value in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data structures
at a random address at each boot.The bootloader supports randomizing
the virtual address at which the kernel image is loaded.
The bootloader must provide entropy by passing a random u64 value
in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Chanho Park [Thu, 31 Aug 2023 07:52:47 +0000 (16:52 +0900)]
fpga: define dummy fpga_load function for debug build
This fixes below build error when CC_OPTIMIZE_FOR_DEBUG is enabled and
CONFIG_FPGA or CONFIG_SPL_FPGA are not enabled.
When CC_OPTIMIZE_FOR_DEBUG is enabled, unused code will not be optimized
out. Hence, fpga_load function must have a dummy implementation to avoid
the build error.
../common/spl/spl_fit.c:591: undefined reference to `fpga_load'
collect2: error: ld returned 1 exit status
pinctrl: zynqmp: Add version check for TRISTATE configuration
Support for configuring TRISTATE parameter is added in ZYNQMP PMUFW(Xilinx
ZynqMP Platform Management Firmware) Configuration Param Set version 2.0.
If the requested configuration is TRISTATE then check the version before
requesting Xilinx firmware to set the configuration.
projects / u-boot.git / log
