This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
mt7622-bananapi-bpi-r64.dtb \
mt7623n-bananapi-bpi-r2.dtb \
mt7629-rfb.dtb \
+ mt7981-rfb.dtb \
+ mt7981-emmc-rfb.dtb \
+ mt7981-sd-rfb.dtb \
mt7986a-rfb.dtb \
mt7986b-rfb.dtb \
mt7986a-sd-rfb.dtb \
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7981.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "mt7981-rfb";
+ compatible = "mediatek,mt7981", "mediatek,mt7981-rfb";
+ chosen {
+ stdout-path = &uart0;
+ tick-timer = &timer0;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+ð {
+ status = "okay";
+ mediatek,gmac-id = <0>;
+ phy-mode = "sgmii";
+ mediatek,switch = "mt7531";
+ reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&pinctrl {
+ spic_pins: spi1-pins-func-1 {
+ mux {
+ function = "spi";
+ groups = "spi1_1";
+ };
+ };
+
+ uart1_pins: spi1-pins-func-3 {
+ mux {
+ function = "uart";
+ groups = "uart1_2";
+ };
+ };
+
+ /* pin15 as pwm0 */
+ one_pwm_pins: one-pwm-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1";
+ };
+ };
+
+ /* pin15 as pwm0 and pin14 as pwm1 */
+ two_pwm_pins: two-pwm-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1", "pwm1_0";
+ };
+ };
+
+ /* pin15 as pwm0, pin14 as pwm1, pin7 as pwm2 */
+ three_pwm_pins: three-pwm-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1", "pwm1_0", "pwm2";
+ };
+ };
+
+ mmc0_pins_default: mmc0default {
+ mux {
+ function = "flash";
+ groups = "emmc_45";
+ };
+ conf-cmd-dat {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO",
+ "SPI0_CS", "SPI0_HOLD", "SPI0_WP",
+ "SPI1_CLK", "SPI1_MOSI", "SPI1_MISO";
+ input-enable;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ conf-clk {
+ pins = "SPI1_CS";
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+ conf-rst {
+ pins = "PWM0";
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&two_pwm_pins>;
+ status = "okay";
+};
+
+&watchdog {
+ status = "disabled";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_default>;
+ bus-width = <8>;
+ max-frequency = <52000000>;
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ vmmc-supply = <®_3p3v>;
+ non-removable;
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7981.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "mt7981-rfb";
+ compatible = "mediatek,mt7981", "mediatek,mt7981-rfb";
+ chosen {
+ stdout-path = &uart0;
+ tick-timer = &timer0;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+ð {
+ status = "okay";
+ mediatek,gmac-id = <0>;
+ phy-mode = "sgmii";
+ mediatek,switch = "mt7531";
+ reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&pinctrl {
+ spi_flash_pins: spi0-pins-func-1 {
+ mux {
+ function = "flash";
+ groups = "spi0", "spi0_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+
+ spi2_flash_pins: spi2-spi2-pins {
+ mux {
+ function = "spi";
+ groups = "spi2", "spi2_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
+ };
+
+ conf-pd {
+ pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
+ };
+ };
+
+ spic_pins: spi1-pins-func-1 {
+ mux {
+ function = "spi";
+ groups = "spi1_1";
+ };
+ };
+
+ uart1_pins: spi1-pins-func-3 {
+ mux {
+ function = "uart";
+ groups = "uart1_2";
+ };
+ };
+
+ /* pin15 as pwm0 */
+ one_pwm_pins: one-pwm-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1";
+ };
+ };
+
+ /* pin15 as pwm0 and pin14 as pwm1 */
+ two_pwm_pins: two-pwm-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1", "pwm1_0";
+ };
+ };
+
+ /* pin15 as pwm0, pin14 as pwm1, pin7 as pwm2 */
+ three_pwm_pins: three-pwm-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1", "pwm1_0", "pwm2";
+ };
+ };
+};
+
+&spi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ status = "okay";
+ must_tx;
+ enhance_timing;
+ dma_ext;
+ ipm_design;
+ support_quad;
+ tick_dly = <2>;
+ sample_sel = <0>;
+
+ spi_nand@0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <52000000>;
+ };
+};
+
+&spi2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_flash_pins>;
+ status = "okay";
+ must_tx;
+ enhance_timing;
+ dma_ext;
+ ipm_design;
+ support_quad;
+ tick_dly = <2>;
+ sample_sel = <0>;
+
+ spi_nor@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <52000000>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&two_pwm_pins>;
+ status = "okay";
+};
+
+&watchdog {
+ status = "disabled";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7981.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "mt7981-rfb";
+ compatible = "mediatek,mt7981", "mediatek,mt7981-sd-rfb";
+ chosen {
+ stdout-path = &uart0;
+ tick-timer = &timer0;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+ð {
+ status = "okay";
+ mediatek,gmac-id = <0>;
+ phy-mode = "sgmii";
+ mediatek,switch = "mt7531";
+ reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&pinctrl {
+ spic_pins: spi1-pins-func-1 {
+ mux {
+ function = "spi";
+ groups = "spi1_1";
+ };
+ };
+
+ uart1_pins: spi1-pins-func-3 {
+ mux {
+ function = "uart";
+ groups = "uart1_2";
+ };
+ };
+
+ /* pin15 as pwm0 */
+ one_pwm_pins: one-pwm-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1";
+ };
+ };
+
+ /* pin15 as pwm0 and pin14 as pwm1 */
+ two_pwm_pins: two-pwm-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1", "pwm1_0";
+ };
+ };
+
+ /* pin15 as pwm0, pin14 as pwm1, pin7 as pwm2 */
+ three_pwm_pins: three-pwm-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1", "pwm1_0", "pwm2";
+ };
+ };
+
+ mmc0_pins_default: mmc0default {
+ mux {
+ function = "flash";
+ groups = "emmc_45";
+ };
+ conf-cmd-dat {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO",
+ "SPI0_CS", "SPI0_HOLD", "SPI0_WP",
+ "SPI1_CLK", "SPI1_MOSI", "SPI1_MISO";
+ input-enable;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ conf-clk {
+ pins = "SPI1_CS";
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+ conf-rst {
+ pins = "PWM0";
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&two_pwm_pins>;
+ status = "okay";
+};
+
+&watchdog {
+ status = "disabled";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_default>;
+ bus-width = <4>;
+ max-frequency = <52000000>;
+ cap-sd-highspeed;
+ r_smpl = <0>;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_3p3v>;
+ status = "okay";
+};
--- /dev/null
+MT7981
+M: Sam Shih <sam.shih@mediatek.com>
+S: Maintained
+F: board/mediatek/mt7981
+F: include/configs/mt7981.h
+F: configs/mt7981_emmc_rfb_defconfig
+F: configs/mt7981_rfb_defconfig
+F: configs/mt7981_sd_rfb_defconfig
+F: configs/mt7981_spim_nand_rfb_defconfig
+F: configs/mt7981_spim_nor_rfb_defconfig
--- /dev/null
+# SPDX-License-Identifier: GPL-2.0
+
+obj-y += mt7981_rfb.o
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih@mediatek.com>
+ */
+
+int board_init(void)
+{
+ return 0;
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_POSITION_INDEPENDENT=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_SYS_TEXT_BASE=0x41e00000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x80000
+CONFIG_ENV_OFFSET=0x300000
+CONFIG_DEFAULT_DEVICE_TREE="mt7981-emmc-rfb"
+CONFIG_TARGET_MT7981=y
+CONFIG_DEBUG_UART_BASE=0x11002000
+CONFIG_DEBUG_UART_CLOCK=40000000
+CONFIG_SYS_LOAD_ADDR=0x46000000
+CONFIG_DEBUG_UART=y
+# CONFIG_AUTOBOOT is not set
+CONFIG_DEFAULT_FDT_FILE="mt7981-emmc-rfb"
+CONFIG_LOGLEVEL=7
+CONFIG_LOG=y
+CONFIG_SYS_PROMPT="MT7981> "
+CONFIG_SYS_CBSIZE=512
+CONFIG_SYS_PBSIZE=1049
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_UNLZ4 is not set
+# CONFIG_CMD_UNZIP is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_GPT_RENAME=y
+CONFIG_CMD_LSBLK=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_READ=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SMC=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CLK=y
+CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_MMC_MTK=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_MEDIATEK_ETH=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_MT7981=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_SERIAL=y
+CONFIG_MTK_SERIAL=y
+CONFIG_FAT_WRITE=y
+CONFIG_HEXDUMP=y
+# CONFIG_EFI_LOADER is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_POSITION_INDEPENDENT=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_SYS_TEXT_BASE=0x41e00000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_DEFAULT_DEVICE_TREE="mt7981-rfb"
+CONFIG_TARGET_MT7981=y
+CONFIG_DEBUG_UART_BASE=0x11002000
+CONFIG_DEBUG_UART_CLOCK=40000000
+CONFIG_SYS_LOAD_ADDR=0x46000000
+CONFIG_DEBUG_UART=y
+# CONFIG_AUTOBOOT is not set
+CONFIG_DEFAULT_FDT_FILE="mt7981-rfb"
+CONFIG_LOGLEVEL=7
+CONFIG_LOG=y
+CONFIG_SYS_PROMPT="MT7981> "
+CONFIG_SYS_CBSIZE=512
+CONFIG_SYS_PBSIZE=1049
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_UNLZ4 is not set
+# CONFIG_CMD_UNZIP is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_SF_TEST=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SMC=y
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_BLK=y
+CONFIG_HAVE_BLOCK_DEVICE=y
+CONFIG_CLK=y
+# CONFIG_MMC is not set
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_MTD_SPI_NAND=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_EON=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_ISSI=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPI_FLASH_XMC=y
+CONFIG_SPI_FLASH_XTX=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_MEDIATEK_ETH=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_MT7981=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_DM_SERIAL=y
+CONFIG_MTK_SERIAL=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_MTK_SPIM=y
+CONFIG_HEXDUMP=y
+# CONFIG_EFI_LOADER is not set
--- /dev/null
+CONFIG_ARM=y
+CONFIG_POSITION_INDEPENDENT=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_SYS_TEXT_BASE=0x41e00000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x80000
+CONFIG_ENV_OFFSET=0x300000
+CONFIG_DEFAULT_DEVICE_TREE="mt7981-sd-rfb"
+CONFIG_TARGET_MT7981=y
+CONFIG_DEBUG_UART_BASE=0x11002000
+CONFIG_DEBUG_UART_CLOCK=40000000
+CONFIG_SYS_LOAD_ADDR=0x46000000
+CONFIG_DEBUG_UART=y
+# CONFIG_AUTOBOOT is not set
+CONFIG_DEFAULT_FDT_FILE="mt7981-sd-rfb"
+CONFIG_LOGLEVEL=7
+CONFIG_LOG=y
+CONFIG_SYS_PROMPT="MT7981> "
+CONFIG_SYS_CBSIZE=512
+CONFIG_SYS_PBSIZE=1049
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_BOOTM_PLAN9 is not set
+# CONFIG_BOOTM_RTEMS is not set
+# CONFIG_BOOTM_VXWORKS is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_UNLZ4 is not set
+# CONFIG_CMD_UNZIP is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_GPT_RENAME=y
+CONFIG_CMD_LSBLK=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_READ=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SMC=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CLK=y
+CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_MMC_MTK=y
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_MEDIATEK_ETH=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_MT7981=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_MTK_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_SERIAL=y
+CONFIG_MTK_SERIAL=y
+CONFIG_FAT_WRITE=y
+CONFIG_HEXDUMP=y
+# CONFIG_EFI_LOADER is not set
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Configuration for MediaTek MT7981 SoC
+ *
+ * Copyright (C) 2022 MediaTek Inc.
+ * Author: Sam Shih <sam.shih@mediatek.com>
+ */
+
+#ifndef __MT7981_H
+#define __MT7981_H
+
+#include <linux/sizes.h>
+
+#define CONFIG_SYS_NONCACHED_MEMORY SZ_1M
+
+/* Uboot definition */
+#define CONFIG_SYS_UBOOT_BASE CONFIG_SYS_TEXT_BASE
+
+/* SPL -> Uboot */
+#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
+
+/* DRAM */
+#define CONFIG_SYS_SDRAM_BASE 0x40000000
+
+#endif