When a message is written by a log driver (e.g. via the network stack) this
may result in the generation of further messages. We cannot allow these
additional messages to be emitted as this might result in an infinite
recursion.
Up to now only the syslog driver was safeguarded. We should safeguard all
log drivers instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
optee: add property no-map to secure reserved memory
OP-TEE reserved memory node must set property "no-map" to prevent
Linux kernel from mapping secure memory unless what non-secure world
speculative accesses of the CPU can violate the memory firmware
configuration.
Fixes: 6ccb05eae01b ("image: fdt: copy possible optee nodes to a loaded devicetree") Signed-off-by: Etienne Carriere <etienne.carriere@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
fdtdec: optionally add property no-map to created reserved memory node
Add boolean input argument @no_map to helper function
fdtdec_add_reserved_memory() to add or not "no-map" property
for an added reserved memory node.
Property no-map is used by the Linux kernel to not not map memory
in its static memory mapping. It is needed for example for the|
consistency of system non-cached memory and to prevent speculative
accesses to some firewalled memory.
No functional change. A later change will update to OPTEE library to
add no-map property to OP-TEE reserved memory nodes.
Simon Glass [Sun, 6 Sep 2020 16:39:08 +0000 (10:39 -0600)]
binman: Allow selecting default FIT configuration
Add a new entry argument to the fit entry which allows selection of the
default configuration to use. This is the 'default' property in the
'configurations' node.
Update the Makefile to pass in the value of DEVICE_TREE or
CONFIG_DEFAULT_DEVICE_TREE to provide this information.
Signed-off-by: Simon Glass <sjg@chromium.org> Suggested-by: Michal Simek <michal.simek@xilinx.com>
binman: Document how CROSS_COMPILE, CC, HOSTCC etc. are used in README
Explain that binman interprets these environment variables in the
"External tools" section to run target/host specific versions of the
tools, and add a new section on how to use CROSS_COMPILE to run the
tests on non-x86 machines.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Allow resolving host-specific tools from env vars
This patch lets tools.Run() use host-specific versions with the
for_host keyword argument, based on the host-specific environment
variables (HOSTCC, HOSTOBJCOPY, HOSTSTRIP, etc.).
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Use target-specific tools when cross-compiling
Currently, binman always runs the compile tools like cc, objcopy, strip,
etc. using their literal name. Instead, this patch makes it use the
target-specific versions by default, derived from the tool-specific
environment variables (CC, OBJCOPY, STRIP, etc.) or from the
CROSS_COMPILE environment variable.
For example, the u-boot-elf etype directly uses 'strip'. Trying to run
the tests with 'CROSS_COMPILE=i686-linux-gnu- binman test' on an arm64
host results in the '097_elf_strip.dts' test to fail as the arm64
version of 'strip' can't understand the format of the x86 ELF file.
This also adjusts some command.Output() calls that caused test errors or
failures to use the target versions of the tools they call. After this,
patch, an arm64 host can run all tests with no errors or failures using
a correct CROSS_COMPILE value.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
These test files are currently "intended for use on x86 hosts", but most
of the tests using them can still pass when cross-compiled to x86 on an
arm64 host.
This patch enables non-x86 hosts to run the tests by specifying a
cross-compiler via CROSS_COMPILE. The list of variables it sets is taken
from the top-level Makefile. It would be possible to automatically set
an x86 cross-compiler with a few blocks like:
But it wouldn't propagate to the binman process calling this Makefile,
so it's better just raise an error and expect 'binman test' to be run
with a correct CROSS_COMPILE.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
buildman: Use git worktrees instead of git clones when possible
This patch makes buildman create linked working trees instead of clones
of the source repository, but keeps updating the older clones of the
repository that might already exist. These worktrees share "everything
except working directory specific files such as HEAD, index, etc." with
the source repository. See the git-worktree(1) manual page for more
information.
If git-worktree isn't available, silently falls back to cloning the
repository.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 1 Sep 2020 11:14:00 +0000 (05:14 -0600)]
Makefile: Support missing external blobs always
At present binman warns about missing external blobs only when the
BUILD_ROM is defined. Enable this behaviour always, since many boards
are starting to use these (e.g. ARM Trusted Firmware's BL31).
Simon Glass [Tue, 1 Sep 2020 11:13:59 +0000 (05:13 -0600)]
binman: Support generating FITs with multiple dtbs
In some cases it is useful to generate a FIT which has a number of DTB
images, selectable by configuration. Add support for this in binman,
using a simple iterator and string substitution.
Simon Glass [Tue, 1 Sep 2020 11:13:57 +0000 (05:13 -0600)]
binman: Move 'external' support into base class
At present we have an Entry_blob_ext which implement a blob which holds an
external binary. We need to support other entry types that hold external
binaries, e.g. Entry_blob_named_by_arg. Move the support into the base
Entry class to allow this.
Simon Glass [Tue, 1 Sep 2020 11:13:56 +0000 (05:13 -0600)]
libfdt: Detected out-of-space with fdt_finish()
At present the Python sequential-write interface can produce an error when
it calls fdt_finish(), since this needs to add a terminating tag to the
end of the struct section.
Fix this by automatically expanding the buffer if needed.
Simon Glass [Tue, 1 Sep 2020 11:13:54 +0000 (05:13 -0600)]
binman: Allow entry args to be required
If an entry argument is needed by an entry but the entry argument is not
present, then a strange error can occur when trying to read the file.
Fix this by allowing arguments to be required. Select this option for the
cros-ec-rw entry. If a filename is provided in the node, allow that to be
used.
Also tidy up a few related tests to make the error string easier to find,
and fully ignore unused return values.
Walter Lozano [Wed, 29 Jul 2020 16:17:31 +0000 (13:17 -0300)]
core: improve of_match_ptr with OF_PLATDATA
Currently of_match_ptr is used to avoid referencing compatible strings
when OF_CONTROL is not enabled. This behaviour could be improved by
taking into account also OF_PLATDATA, as when this configuration is
enabled the compatible strings are not used at all.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 29 Aug 2020 17:36:14 +0000 (11:36 -0600)]
binman: Use pkg_resources to find resources
At present we look for resources based on the path of the Python module
that wants them. Instead we should use Python's pkg_resources feature
which is designed for this purpose.
binman: Build FIT image subentries with the section etype
When reading subentries of each image, the FIT entry type directly
concatenates their contents without padding them according to their
offset, size, align, align-size, align-end, pad-before, pad-after
properties.
This patch makes sure these properties are respected by offloading this
image-data building to the section etype, where each subnode of the
"images" node is processed as a section. Alignments and offsets are
respective to the beginning of each image. For example, the following
fragment can end up having "u-boot-spl" start at 0x88 within the final
FIT binary, while "u-boot" would then end up starting at e.g. 0x20088.
fit {
description = "example";
images {
kernel-1 {
description = "U-Boot with SPL";
type = "kernel";
arch = "arm64";
os = "linux";
compression = "none";
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Reinstate check in testPadInSections(), squash in
"binman: Allow FIT binaries to have missing external blobs" Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
binman: Respect pad-before property of section subentries
Other relevant properties (pad-after, offset, size, align, align-size,
align-end) already work since Pack() sets correct ranges for subentries'
data (.offset, .size variables), but some padding here is necessary to
align the data within this range to match the pad-before property.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Wolfgang Wallner [Wed, 16 Sep 2020 14:57:53 +0000 (16:57 +0200)]
x86: acpi: Add memset to initialize SPCR table
Add a missing memset to acpi_create_spcr().
The other acpi_create_xxxx() functions perform a memset on their
structures, acpi_create_spcr() does not and as a result the contents of
this table are partly uninitialized (and thus random after every reset).
Fixes: b288cd960072 ("x86: acpi: Generate SPCR table") Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix the tags format in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Wolfgang Wallner [Fri, 11 Sep 2020 14:52:28 +0000 (16:52 +0200)]
x86: fsp: Replace e-mmc with emmc in devicetree bindings
The term eMMC is used inconsistently within the FSP devicetree
bindings (e-mmc and emmc), especially for "emmc-host-max-speed"
documentation and code disagree.
Change all eMMC instances within the FSP bindings to consistently
use "emmc". The term "emmc" is already used a lot within U-Boot,
while "e-mmc" is only used in the FSP bindings.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Fixes: 0b885bcfd9b0 ("acpi: Add an acpi command") Cc: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Tue, 8 Sep 2020 13:57:22 +0000 (16:57 +0300)]
x86: edison: Move config SYS_MALLOC_LEN to Kconfig
This patch moves the the config SYS_MALLOC_LEN to Kconfig
as it is already done for zynq arch in commit 01aa5b8f0503
("Kconfig: Move config SYS_MALLOC_LEN to Kconfig for zynq").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Sat, 19 Sep 2020 12:31:52 +0000 (08:31 -0400)]
Merge branch '2020-09-18-assorted-bugfixes'
- SquashFS Coverity fixes
- bitflip fix in the alternate memtest command
- Disable networking on bcmstb boards where we didn't have any network
drivers enabled.
Maxim Uvarov [Fri, 28 Aug 2020 19:20:10 +0000 (22:20 +0300)]
efi: change 'env -e -i' usage syntax
'env -e -i' syntax was changed from "," to ":". Account for this also
in the documentation.
Fixes: 2b3fbcb59f41 ("efi_loader: use ':' as separator for setenv -i") Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Correct the usage description for setenv -e too. Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Allow specifying the node on which a property is searched.
Test the device tree consistency more rigorously.
Some efi_st_printf() calls have been converted to efi_st_error().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Robert Marko [Thu, 10 Sep 2020 14:00:05 +0000 (16:00 +0200)]
usb: dwc3: Add Qualcomm DWC3 compatible string
Lot of Qualcomm SoC-s use DWC3 controller for both USB2.0 and USB3.0
ports.
Qualcomm has some custom config registers on top of the generic ones,
but for host mode these are not needed.
So lets add the neccessary compatible string.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr>
Robert Marko [Thu, 10 Sep 2020 14:00:02 +0000 (16:00 +0200)]
reset: Add IPQ40xx reset controller driver
On Qualcomm IPQ40xx SoC series, GCC clock IP also handles the resets.
So since this will be needed by further drivers, lets add a driver for the reset controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr>
Ralph Siemsen [Wed, 9 Sep 2020 16:10:00 +0000 (12:10 -0400)]
cmd: mem: fix range of bitflip test
The bitflip test uses two equal sized memory buffers. This is achieved
by splitting the range of memory into two pieces. The address of the
second buffer, as well as the length of each buffer, were not correctly
calculated. This caused bitflip test to access beyond the end of range.
This patch fixes the pointer arithmetic problem.
A second problem arises because u-boot "mtest" command expects the
ending address to be inclusive. When computing (end - start) this
results in missing 1 byte of the requested length. The bitflip test
expects a count rather than an "ending" address. Thus it fails to test
the last word of the requested range. Fixed by using (end - start + 1).
Added Kconfig option to optionally disable the bitflip test, since it
does add significantly to the time taken for "mtest".
Fixes: 8e434cb705d463bc8cff935160e4fb4c77cb99ab ("cmd: mem: Add bitflip
memory test to alternate mtest")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org> Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Thu, 17 Sep 2020 13:55:01 +0000 (09:55 -0400)]
Merge tag 'for-v2021.01-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
mpc83xx, keymile boards: enable DM_ETH and add DTS
- mpc83xx: remove unneeded extern declaration in cpu_init
- powerpc, qe: fix codingstyle issues for drivers/qe
- powerpc, qe: add DTS support for parallel I/O ports
- net, qe: add DM support for QE UEC ethernet
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
mmc: fsl_esdhc_imx: check the clock stable status after config the clock rate.
Currently, after config the clock rate, delay 10ms, this is quite a rough
method. Check the clock stable status in the present status register is
enough.
Tested-by: Ji Luo <ji.luo@nxp.com> Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Marek Vasut [Sat, 12 Sep 2020 23:35:08 +0000 (01:35 +0200)]
ARM: mx6: ddr: Add support for iMX6UL/ULL/SL/SDL
This patch adds support for iMX6UL/ULL/SL/SDL MMDC into the DDR calibration
code. The difference between MX6DQ and MX6UL/ULL/SL is that the later SoCs
have 2 SDQS registers, just like MX6SX, while the MX6DQ/MX6SDL has 8.
Fixes: 4f4c128c65 ("ARM: mx6: ddr: Add support for iMX6SX") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Eric Nelson <eric@nelint.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
The size of the binary created with the default U-boot config is much
greater than the default offset for environment `0x60000`.
In case if that binary is used for booting via MMC it is overlapped with
the environment stored on MMC.
This leads to U-Boot corruption while saving environment with `saveenv`
command and non-bootable SabreLite board.
The offset for environment `CONFIG_ENV_OFFSET=0x60000` was added in
commit a09fea1 but did not count in the change to `0xC0000` if option
`CONFIG_ENV_IS_IN_MMC` is used.
The offset is also used for variant with environment saving onto SPI NOR
flash (with enabled option `CONFIG_ENV_IS_IN_SPI_FLASH`). In that case the
U-Boot binary flashed on SPI NOR is also corrupted after environment
saving with the original 0x60000 offset.
Signed-off-by: Denis Pynkin <denis.pynkin@collabora.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Peng Fan [Wed, 16 Sep 2020 07:17:18 +0000 (15:17 +0800)]
imx7: ccm: correct target interface num
According to i.MX 7Dual Applications Processor Reference Manual, Rev. 1
The target interface CCM root index ranges [0,124], so the number
should be 125.
Reported-by: Coverity 18045 Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com>
Igor Opaniuk [Mon, 14 Sep 2020 08:01:10 +0000 (11:01 +0300)]
colibri_imx7: use preboot for fdtfile evaluation
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Igor Opaniuk [Mon, 14 Sep 2020 08:01:09 +0000 (11:01 +0300)]
colibri_vf: use preboot for fdtfile evaluation
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: 304042c1f3("colibri_vf: set fdtfile for distroboot") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Mon, 14 Sep 2020 08:01:08 +0000 (11:01 +0300)]
colibri-imx6ull: use preboot for fdtfile evaluation
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Heiko Schocher [Mon, 3 Feb 2020 06:43:57 +0000 (07:43 +0100)]
mpc83xx, keymile boards: enable DM_ETH and add DTS
enable DTS support for keymile mpc83xx based boards.
get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Therefore done:
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Series-to: u-boot
Series-version: 3
Series-changes: 3
- rebase patchset to current mainline commit c0192950df
- update defconfig files
Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
keymile to DM_ETH
Cover-letter:
powerpc, mpc83xx: add DM_ETH support
This patch series adds DM ethernet support for mpc83xx based
keymile boards.
Heiko Schocher [Thu, 6 Feb 2020 08:48:16 +0000 (09:48 +0100)]
net, qe: add DM support for QE UEC ethernet
add DM/DTS support for the UEC ethernet on QUICC Engine
Block.
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Patch-cc: Madalin Bucur <madalin.bucur@oss.nxp.com>
Series-changes: 3
- revert:
commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled")
as now qe works with DM and DM_ETH support.
- fix mailaddress from Holger
Series-changes: 2
- add comments from Qiang Zhao:
- add device node documentation
- I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c
because using drivers/net/fsl_mdio.c leads in none existent
udevice mdio@3320
instead boards with DM ETH support should use now this
driver.
- remove RFC tag
Commit-notes:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This Code should be removed if all boards are converted
to DM/DTS.
- add the DM based qe uec driver under drivers/net/qe
- Therefore copied the files uccf.c uccf.h uec.h from
drivers/qe. So there are a lot of Codingstyle problems
currently. I fix them in next version if this RFC
patch is OK or it needs some changes.
- The dm based driver code is now under drivers/net/qe/dm_qe_uec.c
Used a lot of functions from drivers/qe/uec.c
- seperated the PHY specific code into seperate file
drivers/net/qe/dm_qe_uec_phy.c
Heiko Schocher [Mon, 3 Feb 2020 09:23:53 +0000 (10:23 +0100)]
powerpc, qe: add DTS support for parallel I/O ports
add DM support for parallel I/O ports on QUICC Engine Block
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Series-changes: 2
- remove RFC
- fixed Codingstyle errors, therefore new patch
powerpc, mpc83xx: fix codingstyle issues for qe_io.c
- moved DM part to drivers/pinctrl
Commit-notes:
Open questions / discussion:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This should be removed if all boards are converted to
DM/DTS.
- Unfortunately linux DTS does not use "pinctrl-"
properties, instead "pio-handle" properties.
Even worser old U-Boot code initializes all pins
defined in "const qe_iop_conf_t qe_iop_conf_tab[]"
table in board code. As linux does the same I decided
to also scan through all subnodes containing "pio-map"
property and initialize them too.
The proper solution would be to check for "pio-handle"
when a device is probed.
projects / u-boot.git / log
